Search Documents

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By J. -F. Lepage, M. A. Tomlinson, K. K. Murray

"The Éléonore mine, located in the James Bay region of Northern Quebec, generates a gold bearing flotation concentrate rich in pyrrhotite. Direct leaching of the finely ground concentrate results in high cyanide consumptions and poor recoveries, so effective pre-treatment to passivate the pyrrhotite is required before leaching. Following a number of process upsets at the mine, test work was performed to better understand the requirements for passivation so a more effective operational strategy could be implemented. This paper outlines the testing and implementation of the new strategy at Éléonore.ÉLÉONORE CONCENTRATOR The Éléonore mine is located 800 km north of Montreal, in the James Bay Region of Quebec, Canada. The ore, containing gold disseminated in sulfide minerals and free fine gold in silicate gangue, is crushed in a two-stage crusher plant before being ground in a single 9,000 kW ball mill. The ball mill is in closed circuit, with about 25% of the cyclone underflow passing through a gravity plant with two, 48” Knelson concentrators. Gold recovery in the gravity circuit varies between 15 and 20%, with gravity concentrate leached daily in an Acacia intensive leach reactor. Cyclone overflow, at a target P80 of 65 microns, flows to the flotation plant where the gold bearing sulfide minerals, mainly pyrrhotite and arsenopyrite, are recovered to concentrate with a mass pull of about 5%. The flotation concentrate, typically containing between 80 and 120 g/t of gold, is thickened and finely ground using a 1500 kW Isa Mill. The finely ground concentrate is diluted, to generate a slurry with about 32% solids by weight, before feeding the leach plant. Initially the concentrate slurry is pre-treated with oxygen and lead nitrate, to passivate the sulphide minerals before cyanide is added for gold dissolution. Gold is recovered from the leached slurry using carbon-in-pulp (CIP). The flotation tailings are also thickened and gold is recovered in a dedicated leach-CIP plant."

Jan 1, 2017

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By A. G. Doll

"This paper expands the SAG mill survey database published by the Author at Procemin 2013. The new database includes 49 published SAG/AG mill surveys and includes mills from all over the world. The paper will compare the survey database to SAG mill models by Austin, Morrell and Hogg & Fuerstenau with the purpose of demonstrating the degree of fit of the models to surveys and validating any empirical “fitting factors” used in the models.SAG mill power draw models are used in mill design and grinding circuit modelling to predict how much power will be consumed by a particular mill geometry and operating configuration. The importance of conducting surveys suited to model calibration will be highlighted because the review of literature shows that survey information important to modelling is often missing or omitted. A recommendation for the collection of data during a mill survey is presented, along with some assumptions used by the Author in the absence of certain data. The benefit to mining companies of publishing their survey data, and thereby allowing modellers to improve their model calibration, is discussed.The comparison of models requires a discussion of the measurement of power in a mill drive system as the models use slightly different position in the electrical network for ""where power is measured"". The benchmarking of models against plant operations requires a similar discussion of power measurement."

Jan 1, 2016

By C. F. Chung, F. P. Agterberg

"Prediction of a variable sulphur content in Cape Breton seams is important for planning the production of a highgrade metallurgical coal. Two extrapolation methods (Kriging and a version of Universal Kriging) to predict sulphur content in blocks of coal before mining are presented and applied to the New Lingan Mine reserves in the Harbour seam. The uncertainty of the predicted values is expressed by using standard deviations. Some statistical results for the Phalen seam, which occurs about 400 ft below the Harbour seam, are presented for comparison. The two mathematical models consist of two sets of equations which have been used in computer algorithms. Some limitations of the present approach and possibilities for further statistical work are indicated."

Jan 1, 1973

By M. H. Pelley

To increase drill fleet capacity and meet increased ore demands at its Carol Lake Project, the Iron Ore Company of Canada initiated a program in 1975 to convert the Gardner-Denver 120 and Bucyrus-Erie 60-R rotary drill fleet from 12 1/4-inch-diameter multi-pass drilling to 15-inch-diameter single-pass drilling. This paper will examine briefly the conversion program , including some tests and results, and examine how the utilization of the 15-inch-diameter blast-holes, coordinated by a comprehensive drilling and blasting program, has improved the drilling, blasting and drilling-plus-blasting aspects of the mine operations, from both economic and operational viewpoints.

Jan 1, 1978

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By A. Ignatieff

This is the second review of developments in coal mining engineering (see C.I.M .M. Transactions, Vol. LI, 1948, pp. 262- 264) and covers the period from October, 1948, to January, 1950. Mechanization The period under review was characterized by the intensive development of appliances providing for complete mechanization of coal-face operations. A variety of machines are being evolved or have already been placed on the market which embody the principle of 'continuous mining'. This trend can be observed in all coal producing countries. In the United States, two continuous mining machines have been developed for entry and room application and by the end of 1 949 were being used in a number of mines. These are the Joy Continuous Miner in which the coal is ripped from the face by means of multiple cutter chains, and the Jeffrey Colmol employing cutters on rotating arms for chipping the coal from the face. The Joy machine is made in tw6l models, 34-in. and 48-in. high and designed for a range of seam thicknesses from 3-ft. -t-in. to 4-ft. 6-in. and from 4-ft. 6-in. to 8ft., respectively. Some experience has been gained with this machine and accounts of its performance are already appearing in the technical literature. The Jeffrey-Colmol has a more limited range of working height. The first model, 38-in. high, was designed for seams about 4 feet in thick11ess but more recently the 28-in. low model has been placed on the market for seams 2-ft. 6-in, to 3-ft. 4-in. in thickness. Conventional mobile loading machines of the gathering-arm type are continuing to yield high production under suitable conditions, and improvements or modifications of the basic principle are embodied in new machines as, for example, the Jeffrey mobile (conveyor) loader with extensible (gathering-arm) head developed for conveyor mining.

Jan 1, 1950

By J. E. Gill

"The name 'Canadian Shield' is used for a vast area; largely in northeastern; Canada; underlain by Precambrian rocks. The part in Canada has an area; of about 1; 790; 000 square miles. Extensions in Greenland; Labrador; Newfoundland; and the United States bring the total area to around 2; 800; 000; square miles. The boundaries of the Canadian part are shown in Fig. 1.; At its margins; the Precambrian rocks can be seen at many places to; extend beneath a cover of flat-lying Palxozoic or later sediments. Information; from borings in the Plains and natural exposures in mountain-built belts; show that similar rocks form a large part of the continental platform. The; Shield; therefore; is a large exposure of what may be regarded as the foundation; of the continent."

Jan 1, 1954

By P. Morissette

Passive monitoring of support performance during rockbursts was conducted at three deep underground mines. A comprehensive database was constructed of 172 seismic events and the associated damage to support systems at 266 mine locations from January 2000 to September 2012. The majority of pertinent information was obtained through seismic system records and on-site field assessments. This work assesses the quality of collected information and evaluates the dynamic-load demand on support systems in seismically active mines.

Aug 1, 2013

By K. Krishnapisharody, S. Clark, M. Barati

Different gas purging methods to metallurgical baths have been applied to date, among which are top lancing and bottom blowing through tuyeres or porous plugs. Among these, the porous plug bottom blowing technique has shown higher efficiency in gas utilization than tuyeres and top blowing, due to smaller bubble size and lower liquid velocity. However, the studies related to bottom stirring of metallurgical baths are limited to slag-less or thin slag-covered melts. In particular, there is no examination of stirring ability in conditions similar to Falconbridge's Slag Make Converter, where the bath is covered with a thick slag layer and a stream of solids is charged on the bath from top. This study was undertaken to investigate the application of gas purging through a porous plug in stirring in and melting of the solid feeds. The spreading behaviour and melting time of a solid layer forming on a plume created by stirring were calculated using the existing models. The results show that formation of a thick solid layer, specifically in areas beyond the plume region is very likely. Nevertheless, the thickness of the layer and melting time do not appear unreasonably high. It is predicted that by proper controlling of gas flowrate and plug configurations, successful solid charging through the mouth can be practiced.

Jan 1, 2007

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By Pierre Bernard

Contents of the presentation ? Overview of Brunswick 12 Mine ? Brief description of the mine geology ? Summary of the current Mineral Reserves and Additional Mineral Resources ? Review of the ongoing mining remnants evaluation process, particularly emphasizing the integrated work between the mine geologists, the mine engineers and the metallurgists ? Challenges and opportunities to extend the mine life

Apr 1, 2005

By André Chagnon, Yvon Héroux

"Résumé - Cette étude porte sur l'altération de la matière organique et des argiles dans les boues carbonatés dévoniennes du faciès ""F"" de la Formation de Pine Point et ses équivalents stratigraphiques la Formation d'Evie et l'unité bitumineuse de la base de la Formation de Horn River. La matière organique se compose principalement de bitume solide et de quelques fragments de fossiles (organo­ clastes). La majorité des échantillons ne renferment que de l'illite et des interstratifiées illite/smectite.Si on compare les températures d'homogénéïsation (Th = l00°C) des inclusions fluides de la sphalérite et des dolomites associées à la minéralisation aux températures estimées à partir de la réflec­ tance de la collinite (84°C à ll7°C), l'on ne peut pas conclure à la présence d'une anomalie ther­ mique dans le district minier de Pine Point. De plus, la réflectance des organoclastes n'est pas plus élevée dans le district minier de Pine Point que dans les localités plus éloignées des gîtes. L'analyse des minéraux argileux conduit à la même conclusion : aucune anomalie thermique n'est décelable dans les unités échantillonnées à l'intérieur du district minier de Pine Point quelque soit l'indicateur utilisé.La kaolinite et la matière organique altérée, affichant des valeurs anomales de sa réflectance, se trouve essentiellement en présence de soufre et de sulfures. Cela suggère une origine authigène de la kaolinite et une altération de la matière organique reliées au phénomènes de minéralisation.Abstract- The alteration of organic matter and clays is studied in the Devonian Pine Point Formation carbonate muds, ""F"" facies, and its lateral equivalents the Evie Formation and the biturninous unit at the base of the Horn River Formation. The organic matter is mainly composed of solid bitumen with few fossil fragments (organoclasts). Most samples contain only illite and mixed layer illite/smectite.If we compare the Th(l00°C) from fluid inclusions of sphalerite and dolomites associated with mineralization to the temperatures calculated from the reflectanœ (Ro) of the collinite (84°C to 117°C), we cannot detect a thermal anomaly in the Pine Point mining district. This result is based on the reflectance values of organoclasts from the mining district that are not higher than those reflectance values measured on organic matter (OM) away from the ore deposit. A similar conclusion is reached from the clay study: none of the parameters used allow us to identify a thermal anomaly in the samples from the mining district.The kaolinite and the altered OM showing anomalous Ro values mainly occur with sulfides and sulfur. This association suggests an authigenic origin for the kaolinite and an alteration of the OM due to the mineralization events."

Jan 1, 1994

By F. Awotwe-Appiah, P. Koshy, A. Y. Fosu, J. Dankwah, J. R. Dankwah

Ghana currently exports its bauxite raw without any value addition. Gradual depletion of high grade bauxite (with high alumina content) and the emergence of low grade bauxite (with high iron oxide content) calls for novel and inexpensive ways to recover alumina from these low grade ores. Bauxite users have indicated their willingness to pay 10% to 50% higher for a corresponding reduction in impurities by a similar amount. This project therefore investigates the carbothermal upgrading of the Ghana Awaso bauxite using waste polypropylene as reductant in a locally designed gas-fired furnace. Composite pellets of low grade bauxite sample (assaying 45% Al2O3) containing pulverised waste polypropylene were formed, oven dried, placed in fireclay crucible and fired for 30 minutes. The magnetic fraction after reduction was separated by a Low Intensity Magnet and weighed. It was observed that up to 97% of the iron oxides (occurring as hematite and goethite) could be separated into the magnetic fraction as magnetite leaving a nonmagnetic fraction with over 98% Al2O3 as opposed to the 45% Al2O3 in the as-received bauxite sample. This research direction provides yet another simple but effective way for simultaneously upgrading low grade bauxite and recycling waste polypropylene, whilst at the same time decreasing the amount of waste material generated as red mud after the Bayer process.

Jan 1, 2015

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By Mehmet F. Tauer, Pierre Trudel

"The metamorphosed mineralized Archean Bourlamaque batholith, dated at 2710 +-54 Ma, is a homogeneous body, composed mainly of quartz diorite; it is cut by late dioritic, mafic and aplitic dykes, and contains metasomatized ultramafic xenoliths. A geochemical investigation confirms the calc-alkaline affinity of the batholith, and the REE profiles are similar (Lal Yb = 3.9 to 8.1) to those of the intermediate to felsic metavolcanic rocks at Val d'Or into which the batholith was intruded and to those of the calc-alkaline members of the Blake River Group at Rouyn.Gold distribution within the batholith is heterogeneous and anomalous. Although the background Au content of the batholith is estimated to be 3.2 ppb Au by RNAA , the estimated median gold content of the batholith is 10 pp b (with P84 =32 and PI 6=3.1 ppb), much higher than that of ""normal"" granites (I to 5 ppb A u). The gold mineralization exhibits a close relationship with shear zones (e.g. Belmoral Mine) or with diorite dykes (e.g. Sullivan, Perron and Courvan mines).The following sequence of geological events is proposed: (I) pretectonic emplacement of the batholith, which is cogenetic with its volcanic host rocks; (2) regional metam orphism and deformation with localized shearing; and (3) hydrothermal alteration and quartz veining. We conclude that: (1) the Bourlamaque batholith is a gold-enriched intrusion, and (2) the determination of average gold content may be an effective method f or distinguishing ""sterile"" intrusions from those with potentials for gold mineralization.RESUMELe batholite archéen minéralise de Bourlamaque, daté de 2710+-54 Ma, est une intrusion homogène, constituée principalement de diorite quartzique, qui a été recoupée par des dykes tardifs de diorite, d'aplite et de composition mafique. Il contient aussi des enclaves de roches ultramafiques metasomatisees. L 'étude géochimique confirme le caractère calco-alcalin du bath olite et les profits des ETR sont semblables (La/ Yb=3.9 a8.1) a ceux des volcanites intermédiaires afe tsiques de la région de Val d'Or dans lesquelles le batholite fait intrusion et à ceux des unites calco-alcalines du Groupe de Blake Ri ver a Rouyn. La distribution de Au dans le batholite est à la fois anomale et hétérogène. Bien que le bruit de fond du batholite ait été estime à 3.2 ppb A u par AANR, sa médiane a été estimée a10 ppb Au (avec P84=32 et PI6= 3.1 ppb) , ce qui est nettement plus élevé que la valeur des roches granitoides ""normales"" donnée dans la littérature (1 a 5 ppb A u). Dans la batholite, la minéralisation aurifère est intimement associée aux zones de cisaillement (e.g. mine Belmoral) au aux dykes de diorite (e.g. mines Sullivan, Perron et Courvan).La séquence des évènements géologiques suivante est proposée: (1) emplacement pre-tectonique du batholite, lequel est cogenetique avec les roches volcaniques encaissantes; (2) deformation et metamorphisme regional avec des cisaillements tectoniques locaux; et (3) altération hydrothermale et développement des veines de quartz. Nous concluons que: (1) le batho lite de Bourlamaque est une intrusion enrichie en Au; (2) la determination de la teneur en Au peu être une méthode efficace pour distinguer les intrusions stériles de celles qui possèderaient un pot entiel pour des minéralisation s aurifères."

Jan 1, 1989