Search Documents

By V Dolmage

In 1957 and 1958, ten topographically suitable damsites were investigated along the Peace river between Finlay Forks and Hudson Hope, B.C. Of these, three were eliminated after a reconnaissance survey indicated that the geology was unsuitable for the 650-ft.-high dam contemplated. ?After extensive drilling, five other sites were deemed unfeasible because of geological factors and, in 1959, the two remaining sites were designated as being suitable, one for the high dam and the other for a low dam downstream. The sites are located in the Peace River canyon, on the west and the south? side of Portage mountain, west of Hudson Hope. The site for the large dam, the Portage Mountain dam, has since been investigated by surface mapping, thousands of feet of diamond drilling, a seismic survey, laboratory rock tests and on-site grouting tests in order to establish the possible effect on the dam of all facets of the foundation rocks. Three diversion tunnels, 50 ft. in diameter and 2,200 feet in length, have been driven through massive sandstone and shale, and an intake cut, 500 ft. in length, 200 feet in width and 200 feet in depth, has also been excavated in rock.

Jan 1, 1963

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977

By B. Daniels, A. Tieu, W. Yan, B. Ren, M. Vijay

"Plasma or thermal sprayed coatings are becoming more widely used in a wide range of industrial applications. The preference to use thermal sprayed coatings is mainly attributed to its superior wear, and corrosion resistant properties akin to hard chrome but without the harmful health implications of chrome in the coating process. Specifically, High Velocity Oxygen Fuel (HVOF) plasma sprayed Tungsten Carbide & Cobalt (WC/Co) coatings are presently being tested on aircraft landing gear. This coating can be efficiently applied and is highly resistant to corrosion and wear. However, HVOF coating's durability also makes it difficult to be stripped for inspection and overhaul. Current coating removal methods usually involve a multi-step process whereby the coating must undergo diamond wheel grinding, chemical dipping, grit blasting, ultrahigh pressure (UHP) 380 MPa (55 Kpsi) water blasting, and subsequent chemical dipping, depending on the type and thickness of the coating. As explained by Yan, et al [l]"" a unique method has been developed for removing HVOF coatings with the use of only water. The method consists of modulating a stream of water at a pressure of only 69 MPa (10 Kpsi) with ultrasonic waves to generate a forced pulsed waterjet. The resulting cyclic loading of the hard coating due to the impact of the water pulses easily causes it to flake off the substrate. This paper will briefly describe the fundamentals of the forced pulsed waterjet technique with an emphasis on insitu applications of the removal of various plasma and HVOF coatings."

Jan 1, 2006

By Dean L. Millar

Measures taken by mining companies around the world to reduce their carbon footprints are becoming increasingly important in the sector securing its social licence to operate. The options for measures reduce to three categories of activity: i) demand reduction by avoiding unnecessary waste of supplied energy, ii) improving the utilization of energy that does have to be consumed and iii) adopting low carbon energy production options?including renewable energy. As well as the environmental imperative, as the prices of electricity, gas and liquid fuels increase, so the economic case for activities i) to iii) gains higher priority, especially in such an energy intensive industry. The specific energy consumption for certain upstream minerals industry operations in Canada is reported to be as follows: underground mining: 99.5 kWh/tonne mined; surface mining: 11.7 kWh/tonne mined; base metal processing: 81.4 kWh/tonne milled; gold processing: 99.6 kWh/tonne milled. Around 508 kWh/tonne (slag) of heat is reported to be available in cooling slag from 1500°C to 25°C; an amount that is simply indicative of the energy intensity of downstream smelting and refining operations. Low carbon, energy saving technology options that are available to mining industry companies lead to projects with return rates that must compete alongside other capital intensive projects considered by mining company boards. Energy projects frequently involve longer payback periods and lower rates of return than those of competing bids for capital, such as those for development of new mineral properties. For energy services companies (ESCOs) that specialize in the financing, construction, and the efficient operation and maintenance of energy projects, the same returns and payback periods may be considered acceptable or even attractive. For the ESCO, the key commercial risk mitigating factor is a securing a long term contract for the supply of energy.

May 1, 2011

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

IDS: The Company IDS Ingegneria Dei Sistemi, founded in 1980, is a world leader as a high technology solution provider in selected niche defense and civil market sectors ? Private and Independent ? IDS?s Quality System is certified ISO 9001 Ed. 2000 ? IDS has the highest Military Clearance ? Continuously measure (24x7) mine wall movements with sub-millimetric accuracy at long distance (up to 4 Km) ? Provide reliable early warning for progressive slope movements potentially leading to mining wall failures ?Map the long term evolution of slow moving slopes to get a better knowledge of the rock mass strength

Aug 1, 2013

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By O. Mejia

"As study was undertaken to investigate the relationship between mill liner wear and grinding energy efficiency and to assess the opportunity to control mill speed to improve energy performance as mill liner wears. The study involved analysis of plant operating data and liner wear profiles over time. The operating work index was found to be an effective tool to identify the decrease of grinding efficiency along the liner service. The plant data show that the mill grinding efficiency as determined by monitoring the operating work index, and throughput decreases as liner wears. However, efficiency and throughput can be maintained by either changing the liner more frequently or by increasing the mill speed. Two scenarios for increasing mill throughput were analyzed. The first one involves changing the liner before the efficiency drops and the second one requires increasing the mill speed from 75% to 79%. Both scenarios show financial benefits that can be used in mill operations.INTRODUCTION The analysis of the mill power draw is used in this study as a key parameter for comparing mill liner profile and its effect on mill performance. Current technology and simulation software used in the mining industry do not factor in the impact of liner wear profiles in grinding efficiency and mill throughput (Toor, 2013). To address this gap, this study provides an analysis of key factors affecting mill throughput and grinding efficiency: mill speed, ball loading, and liner profiles. Several years of plant mill operating data, published research papers, and MillTraj® simulation results are used to demonstrate that face angles impact grinding efficiency and throughput and that mill speed can be used to overcome this problem. Moreover, the liner profile wear analyses clarify a mismatch between actual and estimated power draw calculations."

Jan 1, 2019

By A. Glover

As the demand for natural gas as a prime global energy source continues to grow, the search for new sources of the fuel spreads into geographical areas that are more remote from the marketplace. Along with this comes the need for longer and ever more efficient pipelines. This requirement for higher value in natural gas transportation is satisfied to a large extent through the application of high strength technology and innovative design approaches that support increased design and operating pressures. This paper reviews the latest accomplishments and successes in these technologies for use in gas transmission. It also explores some of the technologies which are targeted for the future to allow the industry to achieve even higher benchmarks in reliability and cost-effectiveness. The central element in the theme of high strength technology for gas pipelines is that of high strength steel. From tensile strengths of Grade 359 a few decades ago, more and more operators are now specifying Grade 550 linepipe for their large diameter projects. As well, Grade 690 steel is operating successfully in limited transmission applications and Grade 825 has recently been installed. With the introduction of the latest high strength pipe comes the need for high strength fittings. The industry's first Grade 550 fittings were recently specified and installed on a project with Grade 825 line pipe. High strength materials can only be implemented successfully if compatible design and construction processes are in place. The latest developments in strain- and reliability based design will be described as well as the corresponding advancements in welding and inspection technology.

Jan 1, 2005

By W. E. Coates

The social ecology of surface mining in urban areas is illustrated by a case study of a recent application for the opening of a new gravel pit in the city of Guelph, including the design of a progressive extraction-rehabilitation sequence for the property, investigation of the ecological impact of the proposed operation, history of the application procedure for a zoning change and the relationship of the operating plan to provincial legislation controlling surface mining.

Jan 1, 1972

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By C. A. Clark

The Chagres Smelter is located 80 kilometres north of Santiago - Chile, in the middle of an agricultural valley which is also one of the poorest districts in the country. This condition sets the main focus for the smelter's Corporate Social Responsibility (CSR) programmes, which ultimately aim at building self sustainable social and economic capital in accordance with the local capacities. With the help of Anglo American's SEAT (Socio Economic Assessment Toolbox), a corporately developed instrument designed to help the operations understand the needs of the communities and the impacts of those operations, the Chagres Smelter implemented several programmes, such as the CETTA (Experimental and Applied Technology Transfer Centre) programme. This project started in 2003, and consists of creating a centre for the transfer of sustainable techniques and skills for the small agricultural and livestock producers that live in the rural areas near the Chagres Smelter. Its main impacts are: Improved production quality (goat cheese and bee honey) and access to relevant markets, improved training and self-sustainability levels of producers, enhanced socio-economic level of the District's inhabitants by improving their income earning opportunities and technical knowledge, creation and promotion of a local brand as a symbol of quality products from the valley and a positive environmental impact of good breeding and native flora protection practices in the area. Other relevant social programmes are the 'Environmental Strivers', which created a recycling centre in the community; and the 'Beautiful Valley" project, which provides management knowledge and skills to local youngsters and leaders who can contribute to finding solutions for local environmental needs.

Jan 1, 2007

By Shinji Muraishi, Shinji Kumai, Yasutaka Kedo, Takashi Kambe

"Magnetic pulse forming (MPF) is one of the extreme high-speed forming processes. A metal sheet which is accelerated by electromagnetic force is collided onto a mold and fine and sharp details of the product can be obtained. The deformation mechanism of the MPFed metal cannot be understood only by the microstructure observation of the deformed metal. The deformation behavior of the metal should be investigated also by considering the local microstructure change with strain, strain rate and temperature change during deformation. Numerical analysis is an effective method to achieve this requirement. In this study, pure Al and Cu sheets were deformed by MPF. Impact velocity of the metal sheet was calculated by using ANSYS Emag-Mechanical. Based on the obtained impact velocity, the deformation behavior of the metal sheet was reproduced, and local strain, strain rate, and temperature were analyzed by using ANSYS AUTODYN. The relationship between the local microstructure change of Al and Cu sheets and the deformation parameters was examined.INTRODUCTIONMagnetic pulse forming (MPF) is one of the high-speed forming processes using electromagnetic force. Fine and sharp details of the product can be obtained, and springback after deformation is extremely reduced in comparison to the conventional forming processes(Psyk, Risch, Kinsey, Tekkaya, & Kleiner, 2011). Figure 1 shows a schematic diagram of MPF. A metal sheet is placed over the coil in the discharge circuit. The discharge current runs through the coil, and magnetic fieldis producedaround the coil. An eddy current is inducedin the metal sheet. Interaction between magnetic field and eddy current creates electromagnetic force. The metal sheet accelerated by electromagnetic forcecollides ontothe mold. Forming is completed in a few tens of micro-seconds.MPF is suitable for metals with a high electrical conductivity like Al and Cu.The MPFed metal may have characteristic microstructure because of high strain rate deformation."

Jan 1, 2018

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By A. C. Hnatyshyn

INTRODUCTION THOSE concerned with coal mining operations in Alberta have been asked repeatedly the same question, "Why is mechanization in Alberta proceeding so slowly as to lag far behind the mines in the United States?" This question is often asked in such a manner as to indicate that a severe reprimand is overdue to the mining engineers of this Province for their apparent indifference to the problem of improving their mining operations by increased mechanization. To the average person, unacquainted with mining conditions and problems, mechanization appears to be simply a matter of introducing equipment to load coal underground and, once this is done, substantial economies in operating costs will automatically follow. Invariably, those who have followed this simple reasoning have found, to their regret, that such is not the case and that effective mechanization involves something more than the mere process of introducing loading equipment into a mine. To be effective, any programme of mechanization must take into consideration all operations incidental to the mining, transportation, and handling of the coal from the working face to the tipple, and must utilize equipment which can be best adapted to any peculiar condition or circumstance prevailing in the mine concerned. In the use of such equipment, the net and final result should be an improvement in operating costs of sufficient magnitude to at least return to the operator, over a specific period of years or during the expected life of that equipment, all his investment plus a fair return on that investment.

Jan 1, 1951

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By H. J. Handewith

"After having performed qualitative and quantitative tests on nearly 550 rock specimens from tunnel projects throughout the world and comparing the results with actual boring in eight distinctly different rock types which varied in compressive strength from 12,000 to over 34,000 psi, it has been concluded that any rock -andesite, granite and even taconite -can be machine-bored. The question is -can it be bored economically? The intent of this paper is to delineate the investigative needs to accurately and reliably answer this question. A piece of NX core in the hand represents less than 50 per cent of the worthwhile geologic information that could have been obtained from a given core hole. A thorough site investigation by competent personnel can gene-rally foretell to what extent, if any, varying geologic conditions will hinder machine progress.A laboratory testing technique has been developed that has been correlated well (80 to 120 per cent) with actual boring results. This technique will be discussed in detail. Rock cutter life is a function of the penetration rate and the forces required to sustain that rate. Cutters are now, and will be for .some time to come, the single, most expensive consumable item involved in continuous tunneling in hard rock. It is by strict attention to predicting these rates and forces that tunneling costs can be optimized."

Jan 1, 1970

By D. Holz

In this work we present a novel level set-based model for the real-time simulation of soil deformations. A level set defined by a signed distance function and sampled in a regular 3D grid represents and tracks the soil volume under deformation. Moving away from classical 2.5D heightfield representations of soil to a full 3D volume representation allows for improved tracking of cutting tool operations and the simulation of near-vertical or vertical soil faces. The proposed level set representation furthermore provides a versatile mathematical platform for modeling additional effects such as soil slip, and does not suffer from the sampling limitations of commonly used heightfields. Cutting forces applied to the tool are simulated via a formulation based on the Fundamental Equation of Earthmoving, modified to support inclined soil surfaces and transient states of tool motion. Discretisation of this 2D cutting force model with respect to the tool surface allows capturing the effects of irregular 3D terrain shapes on blades and buckets. The surcharge created during cutting operations is tracked in the form of particles and included in the soil failure force computation. We make use of an adaptive, hybrid level set-based and particle-based soil deformation scheme, which allows the soil deformation to be simulated in real-time.

Aug 1, 2013

By Gerhard W. Heinrich, Gerald V. Schroeder, Daniel A. Murphy, Daniel F. Suarez, Jamie B. Beauchamp

"Washwater 'Finger' sprays were installed and tested in the copper/nickel separation circuit at Strathcona Mill to improve flotation capacities and related metallurgical performances. The new spray design features submerged sideways introduction of wash water into the flotation froth through nozzles at the end of vertical pipes which are suspended from a header above the froth. This maximizes the effective cross sectional area of flotation vessels while maintaining effective froth cleaning and a desirably high density of the concentrate slurry. The plant tests gave increases of copper concentrate production rates of 17% to 20% for conventional cells and 16% to 20% in column flotation at target grades of 29% to 30% copper and of less than 0.5% nickel. Basic considerations and concepts of tests and evaluation procedures are described.IntroductionMeeting flotation concentrate grade targets at maximum production rates and recoveries is a challenge all too familiar to operators of base metal ore concentrators. Frothwashing is an option to improve grade/recovery performance by minimizing entrainment of impurities into the concentrate, which is commonly known since the sixties (Kaya & Laplante, 1989). It has been recommended for the flotation of sulphides and industrial minerals alike (Kaya & Laplante, 1989; Miller, 1969; Heinrich, 1989) and has found its ultimate application in flotation columns (Finch & Dobby, 1990). The washwater addition in a flotation column is most evenly distributed over the column's cross-sectional area thus ensuring almost complete displacement of feed water from the froth by a countercurrent washwater flow -provided, a positive bias is maintained. Therefore, flotation columns are ideal for cleaning flotation. However, there is usually less room for boosting the concentrate production capacity by increasing airflow or slurry level then with conventional cells because of the smaller cross-sectional area available."

Jan 1, 1994