Search Documents

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting of hand-sorted galena ore from other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the f oundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world 's largest lead-zinc producer).The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, andsteady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name wasshortened to Cominco Ltd.The Rossland mines continued to supply copper ore for the smelter until the late 1920s, but lead-silver ore also became available from the contemporary mining boom in the Slocan area, about 80 km away. In 1901, the Trail smelter diversified into lead; and when the CM&S Co. acquired the St. Eugene Mine at Moyie and the Sullivan Mine at Kimberley, the smelter was guaranteed a firm supply of lead ore. The company also purchased the West Kootenay Power and Light Company, which even before the turn of the century had constructed the first of four hydroelectric generating plants on the Kootenay River near Trail. This acquisition assured the CM&S smelter and its local mines of a stable power supply and the opportunity to diversify into power intensive technology."

Jan 1, 1988

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting offhand-sorted galena orefrom other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the foundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world's largest lead-zinc produce.The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, and steady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name was shortened to Cominco Ltd."

Jan 1, 1988

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase

Aug 1, 2013

By J. S. Fox

Major-element data for unaltered, unmineralized felsic host rocks from a number of stratigraphically simple, massive volcanogenic Zn-Cu(-Pb) sulphide deposits of low metamorphic grade have been compiled. The petrochemical affinities of these host rocks have been determined (by standard means and by discriminant analysis) and compared. This comparison indicates that volcanogenic deposits in felsic terrains are not restricted to the classical calc-alkaline rock association as previously thought, but can actually be hosted by rocks showing a range of iron content. There is a positive correlation between differentiation trend and are tenor. Zn-Cu ores usually have iron-rich felsic hosts (most Canadian Shield deposits); Pb-Zn -Cu ores have iron-poor felsic hosts (Japanese, Iberian and Tasmanian deposits). This parallels the antipathetic relationship between iron content and background lead levels evident in young, unmineralized, island arcs as well as in many older belts. Correlations between differentiation trend on one hand and massive ore mineralogy and the relative proportions of various rock type (including rhyolite, quartz-porphyry and coarse pyroclastic rocks) on the other are also evident. It is concluded that the recognition of a calc-alkaline differentiation trend cannot be used as a prospecting guide, as has previously been proposed. However, in view of the above correlations, the recognition of a given trend may aid in the formulation of an effective exploration philosophy.

Jan 1, 1979

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By Jr. Jones

This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded. A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.

Jan 1, 2012

By R. E. Dye

Introduction Research concerning all phases of hoisting practice, but more particularly the causes and prevention of hoisting rope deterioration and the improvement of safety dogs 158 for shaft conveyances, has been carried on intensively for the past three years in the Province of Ontario. Prior to the hoisting accident at the Paymaster mine on February 2nd, 1945, there had been no fatalities in the Province due to a hoisting rope failure. It was probably on this account that little original research on hoisting problems had been undertaken here and that the mining industry had been content to look to British, South African, and United States investigators for new developments in this field. Except for the Paymaster accident this might still be the case since, in any industry, it is apparently necessary for a serious accident to occur before any extensive programme of preventive research is launched. When this accident occurred, the Government of Ontario, with the close co-operation of the Paymaster officials and the mining industry as a whole, took immediate steps to determine the cause. A five-man, non-industry committee, selected from the Faculty of the University of Toronto with Dean C. R. Young as Chairman, was appointed by the Government, and a three-man Committee consisting of R. D. Parker, General Superintendent of the International Nickel Company of Canada, Limited, R. L. Healy, General Manager of Wright Hargreaves Mines, Limited, and R. E. Dye, General Manager of Dome Mines, Limited, with the latter acting as Chairman, was appointed by the Ontario Mining Association.

Jan 1, 1948

By L. M. Pidgeon

"Part I. - PrinciplesIntroductionIf the oxides of the metals are listed in decreasing order of the magnitude of their heats of formation, the list appearing in Table 1 will be formed. It will be apparent at once that this is essentially the well-known electrochemical series (Table li). The metals at the bottom of the list exhibit great stability and are attacked only by the most violent of chemical reagents. Higher on the list, the metals become more reactive until, at the head of the list, the metals lithium and calcium are unstable in moist air.The reactive metals to be considered lie above manganese. In this group will be found familiar and abundant metals such as aluminium and magnesium, the unfamiliar yet abundant metal titanium, the rare and mysterious metal beryllium, and others of greater or less interest.While these metals exhibit properties as unlike as those of uranium and magnesium, they have in common a specialized and difficult extractive metallurgy. They form compounds of great stability, and their reduction is to varying degrees difficult. The position of a metal in Table 1 (and more particu1arly its position in the free energy column) gives a numerical value to this property.Oxides with low free energies of formation may be reduced with great ease; thus silver and mercury may be produced from their oxides by simple heating in air.Lead, iron, and zinc may be separated from their oxides by heating with carbon to moderate temperatures. Magnesium oxide, on the other hand, .requires a high temperature and very special conditions before it will yield magnesium metal."

Jan 1, 1950

"An innovative concept is proposed whereby the operating power for haul trucks in certain areas of an underground mine are reduced in order to lower ventilation costs. Airflow that must be provided for diesel-powered equipment in most jurisdictions are regulated based on engine peak power capability and engine emissions, both of which can be lowered by artificially reducing the capacity of the engine through the engine control unit. Advances in asset tracking and ventilation on demand enable this methodology and this study demonstrates that it could represent significant value for mine operators. An examination of haul truck duty cycle indicates that de-rating of engine operating power based on the truck’s location in the mine can enable a step change in ventilation rates, often with no material impact on working conditions. Methods for implementation and estimate of cost savings will be defined.INTRODUCTION Ventilation of underground workings remains a significant operating cost burden for modern mine operators. In particular, ventilation rates for underground diesel mining equipment are often defined by local regulatory bodies and are assumed to present minimal opportunity for optimization or savings, at least until battery propulsion systems can be adopted. Commonly, the quantity of air flow required is defined by the peak rated engine output power of diesel equipment. For example, Ontario Regulation 854 SS 183.1 (3) states that “The flow of air must be at least 0.06 cubic metres per second for each kilowatt of power of the diesel-powered equipment operating in the workplace”. Jurisdictions that define air flow using the prescribed CANMET or MSHA ratings use peak engine emissions to calculate air flow required for dilution ventilation. These approaches are similar in that the maximum power capability of a vehicle’s engine is used to define the ventilation rate in all areas where it travels, regardless of what power output is actually used in any of those areas. Examination of the duty cycle of a typical underground haul truck identifies a large variance in the power output of the vehicle depending on its location in the mine and the activities undertaken at these locations. For example, travel on a mining sub-level requires a fraction of the truck’s peak power due to the minimal grade and significantly reduced travel speed. So if we can reliably reduce the peak engine power capacity and engine emissions in areas where peak power is not required, we can logically cut the ventilation rates for those areas."

Jan 1, 2017

By E. P. Williams

"Prince Edward Island, Canada's smallest Maritime Province, is located in the southwestern part of the Gulf of St. Lawrence. The Province is more or less centrally located in the Maritimes Basin, a large intermontane basin within the Appalachian orogenic belt. The Maritimes Basin is subdivided into sub-basins and uplifts which exhibit two dominant structural trends: east and northeast. The Basin is known to be petroliferous because of the seeps, shows, oil shales and albertite found in southern New Brunswick and northern Nova Scotia and the gas and oil produced from the Stony Creek field near Moncton, New Brunswick.Permian beds are exposed on the Island, mostly along sea-cliffs. A maximum thickness of about 5,000 feet of red beds -shales, sandstones and conglomerates -make up the sequence. Over most of the Island, the Permian section is much thinner. Four key wells (Mississippian tests) and several shallower tests have been drilled. The Pennsylvanian-Mississippian section thickens rapidly off the Port Hill Uplift at the northwest, where it is less than 4,600 feet thick, and continues to thicken to about 20,000 feet in the Cumberland Basin at the southeast. Geological and geophysical data combine to give us the structural picture of the deeper beds.Prospective reservoir rocks are primarily in the Missis-sippian Horton and Windsor groups. Prospects are:-1. on or over structural highs in the basement; 2. on anticlines or fault highs; 3. over or peripheral to salt domes or salt-core anticlines; 4. at truncation pinchouts of Mississippian prospective beds; 5. in basal sandstone or granite wash on the pre-Carboni-ferous basement; and 6. in facies traps at changes from sandstone to shale or porous to tight carbonate rocks."

Jan 1, 1967

By R. Jacobs, R. E. L. Pobe

The Moab Khotsong Metallurgical Complex comprises a gold recovery circuit (Noligwa Gold Plant) and a uranium recovery circuit (South Uranium Plant). The metallurgical complex employs the reverse leach technology for the recovery of uranium; specifically, uranium extraction prior to gold using acid leaching processing. The inherent uranium species in the ore are uraninite, coffinite and brannerite. The slurry that has been subjected to the uranium leach is further subjected to solid-liquid separation to separate the uranium in solution through counter-current decantation and the solids (solids carrying all the gold), which are repulped and returned to the gold plant for gold processing. The uranium leaching process is critical to the uranium playing a pivotal role as a value adding by-product to the gold operation. The benefit of adopting this reverse leach process, for improved gold recovery, is that it exposes gold particles occluded within the uranium matrices and avails them for cyanidation. However, the drive for operational efficiency in uranium extraction must be weighed against the incremental operating cost against the backdrop of depressed spot uranium market prices. Over the years, efforts were directed at maintaining the benefit of extracting uranium to enhance gold recovery and simultaneously, optimizing the operating cost model for the uranium operation to remain relevant to the gold operation. The aim of this paper and the corresponding presentation is to give account of the uranium processing optimization journey embarked on over the years; namely, the operational trade-offs made in the process of ensuring that uranium continues to add value to the gold operation. These challenges were faced while striking a fine balance between processing cost and operational efficiencies against the prevailing depressed uranium spot market prices. Mineralogical- and laboratory tests conducted form the support basis for the results and observations articulated in the paper.

Jan 1, 2020

The major factors limiting the establishing of vegetation on the shale and sandstone wastes at Minto are high exchange acidity and low pH (shale pH 4-5, sandstone pH < 4). In the first revegetation program (1967-74), 3.8 million trees were planted without grading on 4,000 acres (red, jack and scots pine and black locust). White dutch and sweet clover, birds-foot trefoil and red top were established in selected areas, and ponds were stocked with brook trout. In the second phase of reclamation, beginning in 1979, a comprehensive plan will be initiated which will allow for forest production, wildlife development and recreational activities.

Jan 1, 1977

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By William Shaw

Conditional simulation is now an accepted tool for managing ore block design at a number of operating mines. It provides a way to consider the quality of data, local continuity and economic risk in defining ore and waste across the cut-off boundary. In addition a computer based system can ensure consistency in making decisions to meet multiple criteria such as cut-off grades, minimum ore-block size and contaminant grade limits. The development of a procedure for using multiple criteria allows ore blocks to be defined using alternative strategies depending on the specific production requirements. This has introduced the opportunity to define ore blocks for different destinations based on their material types and opens the way for geometallurgical modelling to be incorporated into grade control.

Oct 1, 2009

By T. Prietl

Metallurgical vessel linings are multilayered, consisting of refractory bodies, insulation materials, joints, and additional space to control for thermal expansion. A unique biaxial hot testing press (BHTP) was installed at the RHI Refractories Technology Center Leoben, Austria to enable the three-dimensional behaviour of complex vessel lining segments to be investigated under simulated service conditions. Using the BHTP, the heat up and thermo-mechanical behaviour of magnesia chromite brick lining segments with and without mortar filled joints were examined. The results obtained during the initial heat up provided validation of CFD modelling of the lining system. In addition, after the heat up and under steady state conditions, the lining behaviour during deformation-controlled compression and relaxation was examined. These analyses generated important data regarding the stiffness, joint compressibility, and brick damage of the lining segments after cyclic loading and unloading as well as the benefits of using mortar joints in the lining. These investigations were performed in collaboration with the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals, University of Leoben, Austria. The BHTP has been operational since November 2004 and is providing information regarding the thermo-mechanical behaviour of different lining segments.

Jan 1, 2007

"Many underground mines are achieving extended life and optimizing existing facilities by mining at greater depths. The challenges to do this require a sound engineering approach to mine design and mine services, as well as ingenuity in safety design. The social consequence is full utilization of existing infrastructure.Accessing ores at depths of 2000 m to 3000 m requires exceptional hoisting design. May’s theme issue includes a paper that examines a case study of one such hoisting plant, with emphasis on the hoist rope selection at Agnico-Eagle’s Penna shaft. The paper also describes the process whereby consultation with provincial safety authorities resulted in a revised safety factor suited to the hoist. Another paper examines the challenges of ventilating mechanized mines to 3000 m, including air cooling and dilution of diesel exhaust emissions. Vent system designs are discussed, using sound engineering design, and proven technology that minimizes emissions to achieve cost efficiencies. The paper suggests design based on process and ventilation simulators to obtain realistic economic data at the design stage. Increased ground pressures present unique challenges for production and safety. While this is not confined to deep mining, one paper examines rock pressures and seismic events at the Brunswick mine, for which experience may be applied at depth. It describes seismic monitoring as a predictive tool in a real mine situation, and how it is used to improve overall recoveries and maintain worker safety."

Jan 1, 2004