Search Documents

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By S. M. Bradshaw, E. Charikinya

"Microwave induced cracks have the potential to enhance metal recovery from coarse sphalerite particles in heap leaching operations by creating new crack surface areas for lixiviant and enhancing value mineral exposure. The mode of fracture and the extent of mineral exposure due to microwave induced cracks have not yet been investigated. The objective of this study was to determine the extent of particle damage and mineral exposure in microwave treated particles. This was done using X-ray computed tomography (XCT) and image analysis techniques. XCT analysis was conducted on small (–5+4.75 mm), medium (–16+9.5 mm), and large (–25+19 mm) sphalerite ore particles before and after microwave treatment (MT). Geometrical properties, such as volume and surface area of each mineral phase in each particle was determined from the XCT reconstructed images using VGStudioMax image analysis software. These geometrical properties were used to calculate the interfacial areas of sulphide mineral grains in microwave treated particles before and after MT. The ratio of specific interfacial area after MT to specific interfacial area before treatment was used as an indicator of the degree of preferential grain boundary fracture. The results showed significant grain boundary fracture after MT at all sizes. For small sized particles, about 31% of the interfacial area was lost compared to 23 and 16% for medium and large particles, respectively. The results also showed an increase in the degree of mineral grain exposure of 28, 26, and 15% for small, medium, and large particles, respectively, after MT. These results provide experimental evidence supporting improved mineral exposure due to MT. INTRODUCTIONFor some years it has been suggested that microwave treatment (MT) of ores might result in preferential grain boundary fracture that would have benefits such as improved grain exposure and particle weakening. (Kingman, 2006). Most of the experimental work investigating the application of microwaves to mineral processing flow sheets has focused on assessing the benefits of applying microwave technology to flow sheets consisting of size reduction and mechanical flotation cells (Kingman et al., 2004). Experimental studies have shown that coarse crushing during tertiary grinding of microwave treated ore resulted in a better liberated coarser flotation feed (Scott, Bradshaw, & Eksteen, 2008). It has been suggested that improved liberation in milled flotation feed, was due to the presence of grain boundary fracture in microwave treated particles. However, this improvement in coarse particle liberation does not necessarily translate to a significant improvement in downstream flotation recovery (Kobusheshe, 2010). This is as a result of the size limit to the flotation of coarse material, due to detachment forces acting on particle-bubble aggregates, which increase as the particle size increases (Jameson, 2012). Current conventional, mechanically agitated flotation cells are not designed to float coarse material (Jameson, 2012). Hence it has been difficult to show the downstream processing benefits of applying microwaves to ores processed by comminution followed by flotation (Kobusheshe, 2010). It is clear from investigations carried out so far that inappropriate downstream exploitation of microwave treated ore would fail to realise a meaningful process benefit (Kobusheshe, 2010; Ali & Bradshaw, 2011)."

Jan 1, 2016

By ANNE FUZESY

Soluble potassium salts in bedded underground salt deposits supply most of The world demand for potassium f or agricultural and industrial use. The potassium salts, sylvite and carnallite, were f irs, noted in drillcores in southern Saskatchewan during The search for oil and gas in ihe early /940s. Problems in shafi sinking beset pioneering potash companies, however, and cominuous production did no, begin uniil 1962. Powsh deposits in southern Saskatchewan occur within ihe uppermost 60 111 of the Middle Devonian Prairie Evaporite a, depths in excess of 900 m. Four groups of po/ash-bearing haliie beds have been distinguished: the Esierha-::,y, White Bear, Belle Plaine and Paiience Lake members. Powsh deposiis extend a jell' kilomeires into Manitoba and south imo orth Dakoia and non heasiern Moniana. Individual potash-rich beds are extensive and consistent in grade and Th ickness. Local th ickening occurs where carnallite is the dominani poiash mineral. Th e preferred ore, sy lviniie, is a clean mixiure of sylvite and haliie. Carnalliie and insolubles are avoided wherever possible because of Their detrimenwl effects on mine stability, grade and refining. Sy lvin ite is exTracted by underground mining or brought TO swjace as brine in solution mining. Poiash is separaiedfrom halite byfloiation or sequential crystallization. The refined produci, potassium chloride, is employed as a fertilizer ingredient as well as in chemical and other industrial capaciiies. The ten poiash mines of Wesiern Canada all are in Saskatchewan and account for aboui 25 per cem of world production. Faciliiies are being expanded, and a new mine and refinery was planned for ihe Breden bury area. Deposiis in Manitoba also were being evaluaied.

Jan 1, 1984

By C. J. Brown

Since its commercialization thirty years ago, the Recoflo® short bed ion exchange process has been extensively utilized for the recovery of a wide variety of acids and metal salts. In addition to a reduction in resin bed height from 200 cm to 300 cm to 15 cm to 60 cm, the process has a number of features such as utilization of fine mesh resins in a compressed bed which together make it ideal for a number of applications. The process has been extensively exploited, for example, in the metal finishing industry for recovery of valuable chemicals from electroplating, anodizing, etching and pickling wastes. More recently, it has also been applied in the primary metals industry for purification of copper electrolytes and metals recovery from leachates. The paper discusses several of these applications and some of the issues that were found to be key to their success.

Jan 1, 2004

By C. Vanvoren

"Since 1975, the Aluminium Pechiney Research Centre at Saint-Jean-de-Maurienne (LRF) has been concentrating its efforts on designing, testing and perfecting the Aluminium Pechiney point-fed prebaked reduction cell.In 1979, the AP18 cell (180 kA) was industrially launched with the construction and start-up of the F line in Saint-Jean. The following generation, the AP30 (300 kA), with prototypes started in 1981, was launched in 1986 on the Saint-Jean G line. Along with cell design, efficient process control systems were developed to pilot alumina feeding and bath composition. Together, these pots are currently producing 4.6 Mt of aluminum, i.e., 18% of the world’s overall yearly production.In 1989, the research centre faced a new challenge: to push the limits for the size of a reduction cell to further improve the profitability of Greenfield projects. This new generation development was also the opportunity for a significant redesign of the Aluminium Pechiney electrolysis information system.With a track record of ten years of semiindustrial operation with three prototypes, the AP50 technology is now ready for industrial implementation and enables a significant breakthrough to be made in terms of return on investment of a Greenfield smelter."

Jan 1, 2002

Mining Subscribes to Murphy?s Law Personal observations on the past ?Perfect, benign deposit mines can be screwed up-spills and concentrate handling issues ?Long term contamination and water management assessments inadequate ?The ?permitting mentality? and its effects on the application of proponent and regulator resources ?Reliance on simple principles but nature and chemistry is more complex

May 1, 2010

By C. Ketata, M. C. Rockwell

During the operation of a mineral processing plant, the unit processes are investigated by analyzing the data extracted by means of stream sampling. The data structure is identical to the time series form. Data analysis is a crucial step in understanding the plant performance. To control the plant performance efficiently, it is very important to avoid sampling errors, which is impossible. However, it is possible to minimize these errors. The factors influencing these errors are divided into two categories: material properties illustrating its heterogeneity, and sampler features. The purpose of this paper is to study the influence of the material composition variation on sampling errors, and to compare our evaluation method with that of Gy. Note that the stream mass flowrate is assumed to be constant during the sampling process.

Jan 1, 2001

By M. Boodman, E. Gertner

"At first glance, the activities related to mining and mineral exploration appear to be local or domestic, rather than international, in nature. Minerals, as corporeal or tangible property, form an integral part of the land in which they are found until extracted and exploited commercially. Even in the latter phase, the tangible nature of minerals gives the impression that the law governing the commercialization of minerals is the law of their situs at any given time. The nature of minerals appears to negate the international aspect of mineral enterprises.The fundamental flaw in the above analysis is its focus upon the nature of minerals, rather than the role of persons in mineral enterprises. The high costs of mineral exploration and commercialization invariably require the involvement of international consortiums or joint ventures. Governments may not have access to the funds necessary to exploit the mineral resources that they control. Local or domestic enterprises may not have sufficient expertise for mineral exploration. Further, markets for various types of minerals are far from localized or static. For these and other reasons, the tangible and localized nature of minerals belies the fundamentally international nature of mineral exploration and commercialization."

Jan 1, 2004

By Christoph Mueller

Broad band mine communication today is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and TCP/IP on the other side provides an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of cheap development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefor, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. To optimize the use of bandwidth on mining networks using load limited, ?bandwidth wasting? local Ethernet segments, long distance broadband traffic should be carried out using more efficient, deterministic communication backbones providing a guaranteed quality of service for each of the physically separated networks. Open networking and broadband systems however may lead to the anticipation that any demands on bulk data or multimedia traffic can be fulfilled in the future. This definitely will not be the case as the bandwidth demands of applications will be growing as least as fast as the bandwidth provided by communication systems. Looking on those problems from an overall system integration perspective, machines and equipment in the future have to be equipped with intelligent computing devices capable of an intelligent local data preprocessing. Such ?Embedded Machine Information Servers? running commercial computing power in the future will be the intelligent bridge between open networking and a secured, high safety local automation system. These ?Embedded Machine Information Servers? then also can make advantage of intelligent video and audio data preprocessing to store and transmit multimedia information ?on demand? or when the application requires it. Summarizing the potential for the future Ethernet based networking together with powerful communication backbones and intelligent local data preprocessing on the machines in the future will lead the way to integrative, reliable and cost efficient mine automation solutions.

May 1, 2002

By Gerald R. Larocque, Donald F. Grenville

"IN APRIL, 1965, the employee relations department (then called the personnel department) was established as a separate function within the company. Its aims and objectives were to hire an effective work force to operate the open-pit mine and the mill, which were at that time under development and construction. It was also directed to develop a sound policy for employee relations to assist the company in maintaining a stable and properly motivated work force, which included the establishment of satisfactory wage rates and fringe benefits, safety, fire protection and security. During the 8 years that the department has been in existence the scope of the company's operations has expanded to include a zinc plant and an underground mine. The work force has enlarged accordingly and now totals 1,680 employees working at the two sites, separated by 34 road miles. To cover the employee relations functions the department has a total of 29 members at the two sites. The department is organized under a superintendent, who has an employee relations supervisor, a safety director and a fire chief reporting directly to him. The employee relations supervisor, with 2 employment officers and 2 clerks, handles hiring, first-stage employee grievanoos, terminations, employee records, and the organization of company-sponsored functions and meetings. Safety, training and security are the responsibility of the safety director, who has 3 safety supervisors, 16 security men, 1 first-aid attendant and one hearing conservation technician to service the two sites. The fire chief operates as a one-man section responsible for plant-wide fire inspections and fireoriented training. Although"

Jan 1, 1974

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By G. R. Phare

Explosives formulation is dictated by desired field performance, which in turn is dependent on such physical properties as strength, velocity of detonation, sensitivity, and water resistance. The design of explosives to obtain these properties is discussed with some reference to detonation and rock mechanics theory.

Jan 1, 1958

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting of hand-sorted galena ore from other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the f oundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world 's largest lead-zinc producer).The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, andsteady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name wasshortened to Cominco Ltd.The Rossland mines continued to supply copper ore for the smelter until the late 1920s, but lead-silver ore also became available from the contemporary mining boom in the Slocan area, about 80 km away. In 1901, the Trail smelter diversified into lead; and when the CM&S Co. acquired the St. Eugene Mine at Moyie and the Sullivan Mine at Kimberley, the smelter was guaranteed a firm supply of lead ore. The company also purchased the West Kootenay Power and Light Company, which even before the turn of the century had constructed the first of four hydroelectric generating plants on the Kootenay River near Trail. This acquisition assured the CM&S smelter and its local mines of a stable power supply and the opportunity to diversify into power intensive technology."

Jan 1, 1988

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting offhand-sorted galena orefrom other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the foundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world's largest lead-zinc produce.The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, and steady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name was shortened to Cominco Ltd."

Jan 1, 1988

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By J. S. Fox

Major-element data for unaltered, unmineralized felsic host rocks from a number of stratigraphically simple, massive volcanogenic Zn-Cu(-Pb) sulphide deposits of low metamorphic grade have been compiled. The petrochemical affinities of these host rocks have been determined (by standard means and by discriminant analysis) and compared. This comparison indicates that volcanogenic deposits in felsic terrains are not restricted to the classical calc-alkaline rock association as previously thought, but can actually be hosted by rocks showing a range of iron content. There is a positive correlation between differentiation trend and are tenor. Zn-Cu ores usually have iron-rich felsic hosts (most Canadian Shield deposits); Pb-Zn -Cu ores have iron-poor felsic hosts (Japanese, Iberian and Tasmanian deposits). This parallels the antipathetic relationship between iron content and background lead levels evident in young, unmineralized, island arcs as well as in many older belts. Correlations between differentiation trend on one hand and massive ore mineralogy and the relative proportions of various rock type (including rhyolite, quartz-porphyry and coarse pyroclastic rocks) on the other are also evident. It is concluded that the recognition of a calc-alkaline differentiation trend cannot be used as a prospecting guide, as has previously been proposed. However, in view of the above correlations, the recognition of a given trend may aid in the formulation of an effective exploration philosophy.

Jan 1, 1979

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase

Aug 1, 2013

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019