Search Documents

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By Robert S. MacPhail, Chilombo Henry, Arnold Kabamba, David Mukelebai, Suresh Thirunagari, Bukali Victor, Yoram Kapai, Chomba Leonard, Kanna Amarasingham

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate. Developed by Charles Tennant & Co (Canada) Ltd and has shown improved collection properties over SIPX for sulphide minerals flotation. Improvement of recoveries, grades, faster kinetics, lower dosages, high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31. Recent plant trial carried out in the copper circuit at one of the largest copper mine in Zambia shown over US $ 2.00 Million annual improvement on the bottom line over SIPX at current copper prices. Data produced also showed superior grade and recoveries from rougher concentrates that previously had not been attainable with other reagents effectively. Flex 31 has also shown positive outcomes with zinc, Copper/Zinc, arsenopyrite and copper/molybdenum ores.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthate, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by the research division of Charles Tennant & Company (Canada) Limited has produced a chemically enhanced SIPX. This product has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The product was named “FLEX 31”."

Jan 1, 2016

PRESENTATION PURPOSE ? Provide an overview of BC?s Environmental Assessment Actand environmental assessment process ? Identify key issues influencing environmental assessments in BC ENVIRONMENTAL ASSESSMENT ACT ? Major project proposals require an EA before a project can proceed ? Considers potential effects of proposed projects and ways to minimize or avoid adverse effects Minister of Environment and the Minister designated as responsible for project category decide whether or not to certify a project or order further assessment

May 1, 2006

By N. S. Spence

INTRODUCTION WHILE TITANIUM, the element, has been known for over 150 years, titanium, the metal, is a relative newcomer to the metallurgical and industrial scene. The reasons for this chiefly lie in the refract1Hy nature of titanium compounds; the high melting point of the metal; the great activity of elemental titanium, particularly at temperatures close to .and above the melting point; and the pronounced deleterious influence of certain impurities on its mechanical proper-ties. Early efforts at production of the metal were, consequently, either unsuccessful or resulted in products having sub-metallic properties. With the considerable improvement in equipment, materials, and skills that have developed within the past twenty-five years, later investigators have had a better opportunity to overcome some of the inherent practical obstacles and to come to grips with the essential technical problems. NATURAL ABUNDANCE OF TITANIUM Titanium is one of the most abundant metallic elements. It has been estimated (1) that titanium comp-rises about 0.65 per cent of the earth's crust, and therefore ranks fourth among the structurally useful metals in the order: aluminum, iron, magnesium, titanium. It must be appreciated that the relative abundance of the element is only a crude indication of its potential availability, since a very substantial proportion is present as a minor constituent in practically all igneous rocks. By comparison, present-day ores of titanium are relatively few and are but a minor fraction of the estimated total titanium contained in the earth' s crust.

Jan 1, 1951

By Alan D. Akerman

This paper describes the significant advantages and improvements in operational availability, reduced breakdowns, and overall cost reductions that can be achieved through the application of a Reliability Centred Maintenance (RCM) program, including Condition Based Maintenance (CBM) and Equipment Health Monitoring (EHM), in a mine environment. It uses a case study to illustrate the essential elements that constitute the basic requirements to establish such programs. This CBM case study analyzed the Load-Haul- Dump (LHD) vehicle sub-systems and their dominant failure modes, as a precursor to the development of condition indicators. The case study describes a disciplined process to enable condition indicator development and qualification in support of a CBM program. The identified condition indicators vary from readily applicable off-the-shelf monitoring systems and techniques, through to "leading edge" technologies that require further research and development. The paper also explores the developments that have been made in the combination of expert system software associated with modern computer based control systems, and the availability of "intelligent? sensor technology that complement the control system capability.

May 1, 2002

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By Samuel Frimpong

Synthetic fuel is a liquid hydrocarbon fuel synthesized from unconventional resources, such as tar sands, heavy oil, coal, and oil shale. These unconventional resources are immense and will be a major energy source for the 21st Century as the availability of conventional crude oil and natural gas declines. The authors review the available global distributions, production data, research frontiers, and current research organizations involved in tar sands, heavy oil, coal, and oil shale. Tar sands and heavy oil is mainly deposited in Canada, Venezuela, and the United States. Oil shale reserves are found in United States, Jordan, China and Australia. Coal occurs in United States, Russia, China, Canada, and Australia. Major research and development efforts are focused on reserves identification, transportation technologies, production cost modeling, bitumen extraction process improvements, coal liquefaction technologies, elimination of pollutants, greenhouse gases, and safeguarding human health and the environment. This review forms a major source for educating the public about these important energy sources, and the need to develop environmentally sound technologies and policies for their extraction.

May 1, 2007

By J. Lazareck

"XPotential Products Inc. has developed technologies to convert auto shredder residues and other forms of plastic waste into useful products such as posts suitable for retaining walls and parking curbs. The technology is competitive provided low-cost plastic waste is available, and could have applications throughout the world. The paper describes the technology used and illustrates the various processing steps. Development of the TechnologyPresently, state-of-the-art auto shredding yields approximately 75% ferrous and non-ferrous metals and approximately 25% by weight of auto shredder residue (ASR). Advances in metal shredding and non-ferrous metal separation technologies turned XPotential Products Inc.’s attention to ASR as a potential revenue source, or at least a means to markedly reduce the cost of disposal. This abundance of nuisance ASR was, in the company’s view, a potential resource as derelict autos and white goods were similarly perceived 40 years ago. As owners of General Scrap & Car Shredder Ltd. in western Canada, XPotential faced significant disposal costs for four shredders. This journey began over 10 years ago and took many twists and turns until a final course of action was chosen. The recovery of the metallic portion of vehicles and white goods has reached technological maturity and attempts to add value are now achievable only in very small increments."

Jan 1, 2004

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone', or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By K. J. R. Ford

"Significant advances in mining and metallurgical operations have occurred over the last two decades, to define ore bodies via geological mapping, mineralogical analyses, geostatistical models and resource reserve modeling. Metallurgical process measurement, controls and modeling have also significantly progressed, with advanced instrumentation, control software, data capture systems and simulation tools. This progress together with development of the science of geometallurgy has allowed geologists, mineralogists, miners and metallurgists to start working together to define geometallurgical ore units and link these to mine planning and projected metallurgical performance. However, application of full geometallurgical programs into existing mine-processing operations or into new “greenfield” projects has been slow. This is mainly due to higher costs, limited dedicated technical resources and little or no corporate leadership. Additionally, life-of-mine cash flow models, the “dollars”, have been largely driven by ore tonnage rates, pay-metal grades and fixed pay-metal percentage recoveries, with few or no geometallurgical parameters included.Here defined, the “electrons” represent intrinsic ore characteristics embracing chemical composition, mineralogy, gangue components and their associated fundamental metallurgical processing phenomena. With its ever expanding treasure chest of measurement and modeling tools, geometallurgy paints a much clearer picture of the “electrons” for the geologist and metallurgist. But to fully understand and realize the real net value of ores over the life of a mine, a comprehensive link of “electrons to the dollars” is essential. Intrinsic characteristics of geometallurgical ore units are by definition linked to their metallurgical processing, but importantly need also to be related to operating costs, capital requirements and revenue.This paper discusses this important linkage under topics of ore geology and mineralogy, metallurgical processing, waste disposal, environmental issues, metal refining, project engineering and lifeof- mine models. Topics are illustrated by multi-metal references and by case examples from gold ore heap leaching and manganese ore smelting projects. 1"

Jan 1, 2013

By F. G. Pickard

"The Strathcona Concentrator is one of three concentrators presently operated in the Sudbury District by the Nickel Division of Falconbridge Nickel Mines Limited. Production commenced in 1968 at a milling rate of 6,300 tons per operating day. Milling capacity was increased in 1970 to 7,200 tons per operating day. 7he ore contains iron, nickel and copper primarily in the form of pyrrhotite, pentlandite and chalcopyrite, while the common gangue minerals are feldspar, quartz, mica, talc and chlorite. The primary function of the concentrators is not only to liberate sulphides from silicate gangue minerals but also to separate pyrrhotite from the more valuable minerals pentlandite and chalcopyrite.SummaryExcessive wear on steel liners and blinding of grates in a regrind pebble mill of the Hardy Concentrator was corrected by the use of rubber liners and grates. The success of these resulted in their installation as original linings In all grinding units except the rod mills at the Strathcona Concentrator. The operation of rubber liners and grates when sized mine ore was used as the grinding medium was satisfactory confirming the Hardy Concentrator experience. Problems developed when the grinding medium was changed from sized mine ore to steel balls in that blinding of the grates occurred. This resulted in conversion of the units to overflow type mills through removal of the grates. The lifter bar life was significantly increased by using higher lifter bars.Grinding PracticeOperation of a regrind pebble mill commenced in 1961 in the Hardy Concentrator. This operation demonstrated the economic feasibility of using sized mine ore as grinding medium. Problems caused by excessive wear of metal liners and grates combined with blinding of the grates were corrected in 1964 through installation of rubber liners and grates."

Jan 1, 1974

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By H. P. Jacobi

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 65 miles east of Hay River, N.W.T. on the south shore of Great Slave Lake.The milling operation started in the fall of 1965 with a capacity of 5,000 tpd. An addition was put into operation late in 1968 to bring the nominal capacity up to 8,000 tpd. The present milling rate is 11,000 tpd.With a feed grade of approximately 2.9% Pb and 6.0% Zn the annual concentrate production amounts to roughly 130,000 SDT of lead concentrate and 370,000 SDT of zinc concentrate for a total of 1/2 million tons of product.This tonnage is moved by railroad. Pine Point is served by the Great Slave Lake Division (G.S.L.) of the Canadian National Railways which connects to the Northern Alberta Railway System (N.A.R.) at Roma Junction, at Peace River, Alberta. The system in turn connects to the CNR and the CPR in Edmonton, Alberta. From here the concentrates move inland chiefly to Trail, B.C., with some shipment to other Canadian and U.S. smelters, and to the port facilities of Pacific Coast Terminals at New Westminster, B.C. for offshore export.This paper will focus on the problems associated with the movement of lead and zinc concentrates from Pine Point to port facilities on the west coast."

Jan 1, 1975

By S. Auger, S. McDonald, K. Ward

"This preliminary paper provides a summary of lab and mill flotation investigations into the copper collector at two Canadian operations. The orebodies illustrated in these studies both contain mainly copper and zinc with uneconomic quantities of lead. Silver is also present as a secondary precious metal.Each mill has advanced to the extended mill trial stage with Uniflot SP129 as the sole copper collector. The preliminary metallurgical results have indicated higher copper circuit zinc and lead rejection is possible as shown in Case Study #2. In Case Study #1, improved zinc circuit metallurgy has been realized during all the Uniflot copper circuit collector trials. A slight increase in silver recovery has also been observed in the extended trials at both operations. INTRODUCTIONThe Canadian base metal industry is presently going through a rationalization period in response to low metal prices and low grade ore bodies. The response from flotation mills has been to reduce costs by incorporating new technologies such as energy efficient large cells, low moisture pressure filters and low steel consumption SAG mills. Other optimization strategies have been incorporated to get better metallurgical performance such as improved process control and monitoring techniques.The newer flotation plants have embraced many of the latest equipment innovations but they continue to incorporate off-the shelf reagents like xanthate and methylisobutylcarbinol (MIBC) . New collector chemistries have been mostly unsuccessful. Our approach incorporates the best of the old and new chemistry into proprietary formulations that match the application. We have found most single chemical formulations cannot meet the demands of the optimized modern flotation plant."

Jan 1, 1992

By H. A. Steane

"This presentation will cover some crushing and grinding considerations in plant design and operation. There is nothing basically new in the subject matter presented here; however, the viewpoint and interpretation may be novel and some of it controversial.The presentation is based on experience gained in the metallurgical design of plants for Placer Development Limited from 1960 to the present. The plants are listed on SLIDE No. 1.These plants have conventional crushing, followed by rod mill and ball mill grinding. I would like to think that autogenous grinding plants are the answer for eliminating secondary crushing plants and reducing the capital and operating costs; however, the autogenous plants seem to have some problems of their own and I have had no experience with them.Fineness of Grinding RequiredFirst let us consider the fineness of grinding required.The fineness of grind will affect the recovery obtained, and the relationship must be determined. If the grinding is too coarse, some of the valuable mineral, either free or locked in middling grains, will not be floated. However, as grinding is probably the greatest single operating cost, we do not want to grind any finer than is justified economically.Finer grinding should not be carried beyond the point where the net smelter return for the increment saved becomes less than the added operating cost. Even this fineness will be beyond the economic limit because of the additional capital cost for the equipment needed to achieve it. These factors will be discussed in more detail later.The Bond work index is the commonest method of expressing a measure of the effort that has to be expended in grinding. It is the kilowatt-hours required to reduce a ton of rock from an infinite size to 80% passing 100 microns. The formula allows a calculation to be made for other size ranges."

Jan 1, 1976