Search Documents

By M P. Schwarz

In recent years, computational fluid dynamic (CFD) modelling of mechanically stirred flotation cells has been used to study the complexity of the flow within the cells. In CFD modelling, the flotation cell is discretised into individual finite volumes where local values of flow properties are calculated. The flotation effect is studied as three subprocesses including collision, attachment and detachment. In the present work, these subprocesses are modelled in a laboratory flotation cell. The flotation kinetics involving a population balance for particles in a semi-batch process has been developed. From turbulent collision models, the local rates of bubble-particle encounters have been estimated from the local turbulent velocities. The probabilities of collision, adhesion and stabilisation have been calculated at each location in the flotation cell. The net rate of attachment, after accounting for detachments, has been used in the kinetic model involving transient CFD simulations with removal of bubble-particle aggregates to the froth layer. Comparison of the predicted fraction of particles remaining in the cell and the fraction of free particles to the total number of particles remaining in the cell indicates that the particle recovery rate to the pulp-froth interface is much slower than the net attachment rates. For the case studied, the results indicate that the bubbles are loaded with particles quite quickly, and that the bubble surface area flux is the limiting factor in the recovery rate at the froth interface. This explains why the relationship between flotation rate and bubble surface area flux is generally used as a criterion for designing flotation cells. The predicted flotation rate constants also indicate that fine and large particles do not float as well as intermediate sized particles of 120 - 240 ¦m range. This is consistent with the flotation recovery generally observed in flotation practice. The magnitude of the flotation rate constants obtained by CFD modelling indicates that transport rates of the bubble-particle aggregates to the froth layer contribute quite significantly to the overall flotation rate and this is likely to be the case especially in plant-scale equipment.

Jan 1, 2005

By J Mavrogenes, C J. Spandler, S M. Eggins, K Worden

Major occurrences of platinum group minerals (PGM) are in crustally-contaminated, huge, layered igneous complexes (Bushveld and Stillwater) and gabbroic intrusions (Norilsk); relatively minor occurrences include arc-related æzoned Alaskan ultramaficsÆ. In terms of arc-related provenances, the recognition of alluvial PGM in river and beach deposits of southern South Island (Mitchell, 1995), in situ in the Longwoods (Cowden et al, 1990), and the ultramafic-mafic layered Greenhills Complex at Bluff (Spandler et al, 2000) raise the possibility that some economically-significant PGM deposits may exist in New Zealand. The Longwoods and Greenhills are in the Brook Street Terrane which is a remnant of a primitive intra-oceanic arc system of Late Permian-Early Triassic age. The Terrane comprises volcanogenic sequences containing plagioclase- and clinopyroxenephyric basalts, high-MgO ankaramite and dolerite dikes, trondhjemite plutons, and basaltic to andesitic volcaniclastic and sedimentary rocks. The cumulate complexes contain early-formed olivine- and clinopyroxene-rich ultramafic cumulates overlain by anorthite and hornblende-bearing gabbros. Primary (isoferroplatinum) and secondary (sperrylite) platinum group minerals are preserved in chrome-rich spinel pods in basal dunite of the Greenhills Complex. Saturation during early fractionation of primitive high-MgO magmas rather than magma mixing seems likely for the primary PGM. Together with correlative terranes in Queensland and New Caledonia, the Brooks Street Terrane is an exposed cross-section of an extensive Permo-Triassic island-arc system. Most parental magmas were primitive island-arc tholeiites, but other primary magma-types include high-MgO ankaramites and trondhjemites û the latter formed by partial melting of lower crustal clinopyroxene-rich cumulates and gabbros, respectively. The parental ankaramites fractionated to form mafic-ultramafic cumulates and primitive to evolved melts of high-Al basalt to andesite compositions (Takitimus). The Brook Street Terrane is an analogue for modern intra-oceanic islandarc systems and allows detailed study of subvolcanic arc processes.

Jan 1, 2005

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995

By M Rimes

This paper describes a technique to predict achievable head grades and likely variances from target grade for the Shovelanna Iron Ore Project, in the Pilbara region of Western Australia. The block model from which the production schedule is produced was created from a wide spaced drilling program and was classified as an Inferred Resource under the JORC Code. Ideally, production schedules and target grades would be determined using a combination of Proved and Probable reserves. However sometimes it is necessary to consider the requirements of potential off-take parties who have specific grade tolerances. A technique is needed to simulate mining sequences and grade variations early in the planning process, using an æexplorationÆ block model rather than the normal æminingÆ block model. Marketing contracts require examination whether the target grade {Fe, P, SiO2, Al2O3 can be kept constant, or must be revised during the life of the mine. A model (written in ExcelÖ using Visual Basic macros) develops a feasible, close to optimal, mine plan from block model data. Cut-off grades for minable ore are chosen. The model evaluates ore tonnage, grade and stripping ratio against depth. Outputs at this stage include plots of slices through the orebody, at nominated x, y and z coordinates, showing ore grade, waste, drill hole locations and topography. The model then searches for a feasible satisfactory mine plan. The initial grade target is the average for the identified ore blocks. The available block list (ABL) at any time is the set of ore blocks, any one of which can be mined without removing any other ore block. The entire initial ABL has an unacceptably large ætotal grade stressÆ, defined as [(Grade-Target)/Tolerance]2, summed over the four relevant minerals {Fe, P, SiO2, Al2O3}. The model trims the ABL, removing the block most harming the total stress. Trimming is repeated until the total grade stress reduces to an acceptable level. The trimmed ABL defines the first mine campaign. Removing the trimmed block set, a second ABL is exposed, which is again trimmed and mined. The process is automatic: a few seconds computation provides a complete mine plan. Re-running the model with adjusted grade limits quickly shows whether a uniform target can be achieved or whether the target must be modified during the mine life.

Jan 1, 2007

XstrataÆs Mount Isa Copper Operations (MICO) is a world-class mining operation producing in excess of six million tonnes of copper ore per annum from its underground mining operations. The Mount Isa Copper Mines have been producing from the underground operations since 1952. Current copper reserves are 87 million tonnes at 2.8 per cent Cu, extending the mineÆs life beyond 2018. The underground orebodies in the copper mines are divided into nine distinct areas and are mined by sublevel open stoping techniques. One of the nine areas is the hanging wall lens, which consists of two sections; a northern lens (NHWL) and a southern lens (SHWL). The SHWL has a proven reserve of 2.2 million tonnes with an average grade of 2.9 per cent copper. Stopes in the SHWL have an average size of approximately 245 000 tonnes and will be extracted in a primary-secondary mining sequence, producing ore until 2009. This paper discusses various aspects of stope design applied in the southern hanging wall lens, including sequencing options and the rationale for the selected sequence. Design features are also discussed and how they have evolved as more is learnt about the SHWL orebody. These include mass firing techniques, focusing on minimising ground vibrations, using seed wave form analysis and prediction. Rock mechanics issues will also be discussed, in particular the reinforcement of stope hanging walls and the use of instrumentation to monitor behaviour within the hanging wall.

Jan 1, 2006

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963

During 1995 a catastrophic accident took place at the No 2 Vaal Reefs shaft in South Africa, when a locomotive fell onto a cage, causing the death of 104 people. The subsequent Commission of Enquiry found that the safety detaching hook had opened when hit by parts of the falling locomotive, detaching the cage from the rope and allowing the cage to drop 400 m down the shaft. It was believed that had the hook not detached, the rope would have been sufficiently elastic not to have failed, implying that many fatalities may have been avoided. In addition, the risk of accidental opening of hooks due to impact with smaller falling objects in shafts became a concern. This paper deals with a comprehensive statistical investigation that was performed to quantify this risk, establish acceptable levels of such risks and to derive criteria for the resistance of detachment hooks against accidental opening caused by impacts. The investigation involved a survey, dynamic finite element analyses and Monte Carlo simulations.

Jan 1, 2005

By K Gottliebsen

Many hydrometallurgical and chemical processes produce large amounts of acid waste. This is illustrated by the copper S/X-E/W process used at the Mount Gordon mine in North Queensland, which produces a tank house bleed in the form of a concentrated sulphuric acid stream. The bleed stream is necessary to remove impurities such as iron that decrease the efficiency of the electrowinning process. However, this bleed stream comes at a high financial cost due to large quantities of make up sulphuric acid required as well as the need to neutralise the bleed stream prior to disposal. The present work describes the approach taken to develop a solvent extraction process for the selective recovery of sulphuric acid from copper tank house bleed liquor. The proposed extraction system was investigated using a branched long chain aliphatic tertiary amine tris(2-ethylhexyl)amine (TEHA) as the extractant, Shellsol 2046 as the diluent and octanol as a modifier. Computer simulations were used to determine the optimum operating conditions for the recovery process. It was found that the process was able to selectively recover up to 90 per cent of the sulphuric acid from the copper electrolyte. This is recovered as a pure aqueous acid stream at a concentration of up to 130 g/L that can be recycled back into the tank house circuit or other areas of the process. The raffinate acid concentration was reduced from 180 g/L to as low as 18 g/L, significantly reducing waste disposal and the environmental impact of the copper process. The equilibrium data and simulation results were also compared with an alternative extractant, CYANEXR 923. Finally the efficiency of the TEHA extraction system was investigated on a pilot-scale in a pulsed perforated plate column. This information was used in order to scale the process for an industrial application. The same methodology applied in this case study could be used to provide innovative and cost-effective solutions to waste streams encountered in other hydrometallurgical or chemical processes.

Jan 1, 2000

In the early ages man contented himself with the use of such tools and appliances as would assist him in the enlightenment of his labours. With the advancement of science, numerous motives, with modifications and adaptations, have been introduced to enlighten labours, and in many cases have taken the place of man, but it can hardly be said that this applies to shovels, although one of the oldest implements of labour; certainly, with the introduction of the steam shovel the labours of man have been considerably reduced, but the hand shovel of today is used similarly to that of years ago.If the principle of the hand shovel has not been improved upon, it must not be suggested that the manufacturers of this article are not endeavouring to improve its quality, and the main point with which the manufacturers have to contend is the production of an article which will give a maximum of durability combined with a minimum of lightness. In order to accomplish this they must select suitable material, and subject it to such heat treatment process that will produce a shovel having a maximum of hardness and toughness without being unduly brittle, and which will withstand the excessive wear to which it is subjected.In this article an endeavour will be made to explain (a) the manufacture of shovels; (b) the defects commonly met with-the cause of same and measures which are necessary to remedy them.Before doing so a brief description will be given of the class of steel used for shovels; this is an important factor, and a steel which is admirably suitable is a plain carbon one containing approximately 55 - 70% C., and closely resembles that used for the manufacture of railway rails. This plain carbon steel is very extensively used, although at present alloy steels are being utilised to a certain extent for shovel manufacture, and with suitable heat-treatment.

Jan 1, 1926

Felspar occurs in association with quartz in the Broken Hill lode pegmatites and is brilliant green, greenish white, and white in colour. The pegmatites occur mainly in the walls in sporadic patches, parallel to the general dip of the ore deposit. The occurrences are of no economic value.Deposits of marketable felspar occur in pegmatite in a number of localities around Broken Hill, New South Wales.The majority of these are in the form of an irregular outcrop, usually of tapering length and depth. The maximum depth of any deposit yet worked in the district is about 40 ft. The felspar is occasionally contaminated by "blows" of quartz, mica and beryl, but the two latter are profitably marketable when separated.Felspars vary in colour from pink, through grey to snow white, and the colour is not indicative of the mineral content. The largest deposit at present being worked is the Egebeck quarry, about 14 miles south of Cockburn. It is a prominent outcrop, roughly circular and about 150 ft. in diameter, covered by one to three feet of overburden.The felspar is mainly massive, but contains some cleavage planes at approximately 90°. Intrusions of quartz and mica occur in patches, but the deposit appears likely to improve in size, regularity and quality below the present working floor.COMMERCIAL USES.Commercial felspars are mainly used in the ceramic industry, for which a high-grade potash felspar is required.The dental industry requires limited amounts of soda felspar with a very low Fe20s content. The poorer grades...

Jan 1, 1946

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

We can look at the water treatment and management strategies at some recently commissioned mines and minerals processing sites to see the likely future of water in mining. The future of water in mining will be based on a holistic approach to understanding the site water balance, appropriate treatment, reuse where possible, and environmentally managed discharge where required. This paper describes advanced and innovative water treatment and reuse processes as used by mines and mineral processing operations from around the world. Underground mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Mining and processing often accumulates wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and acidic and odorous sulfates. On-site reuse, environmental discharge requirements, as well as community needs for water, drive mine operators to consider the most appropriate water treatment process. Mining water treatment for the future is described using case studies of innovative processes. The case studies include treatment of mine dewatering water for beneficial application from Australian mines, Ballarat Goldfields and Bendigo mining, treatment of produced water from oil and gas projects, and treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Advanced and innovative processes including membrane filtration, reverse osmosis at extreme conditions, advanced biological treatment and water management are all part of these case studies. This paper uses real case studies of advanced and innovative mine water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is on innovative processes that may be more widely used in future mining û where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the mine or the local community.

Jan 1, 2008

With the advent of the resources boom in the late-1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large-scale Australasian open pit mining generally.

Jan 1, 2002

Industry has a very special request to make. Environmental issues must not be allowed to become a factor of competition so that nations or individual industries can gain economic advantages for themselves by encroaching unduly upon the environment. An international harmonisation of the demands imposed on specific industries and industrial plants where discharges are concerned is therefore essential. The same applies to any to any action contemplated against noxious products. An important step towards that goal is no doubt represented by the United Nations Conference on the Environment scheduled for 1972. Conclusions: Australia must recognise its responsibilities in an inter- national movement to control pollution. It must react on a national scale to a problem which is threatening our whole national environment. To gather, collate and coordinate the information needed to ensure policies which strike a balance between conservation and development, we must look towards the Commonwealth to coordinate the activities of its own instrumentalities and those State and independent bodies working in the area. Financial aid must be provided to stimulate research and later to ensure that environmental protection policies are observed. These policies will be founded on social economic theories which will be both practical and sound, The United Nations conference on the Environment is scheduled for 1972 and in this is the opportunity for international cooperation. Cooperation in the field of controlling legislation and the collection of much needed data. There is an imperative need to assemble facts for world use - an international know-how bank which acquires the most sophisticated technology of process design and waste purification. Arising out of this Conference, is it too much to expect that there could be established an international authority for environmental control, whose activities are governed on a multi-national basis? Such an organisation would have as its primary concern the collection and classification of official regulations, as well as the sheer collation of data to permit economic evaluation of the costs of conservation of the environment. There is an international scope with different factors involved, including industrial technology: in other words, the concrete measures taken against industrial pollutants ought to be more or less identical for similar industries irrespectives of the countries in which they operate. The assembling of an international common foundation of knowledge is imperative so as to acquire the most sophisticated technology of process design and waste purification available for all who are interested.

Jan 1, 1971

The Yabulu refinery of Queensland Nickel Pty Ltd located near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation. The economics of this exercise have been considerably enhanced in the past year by changing the project's principal product from nickel oxide sinter to refined high purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site. Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to completely change the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.

Jan 1, 1995

By N C. Steenkamp

The Northern Cape Province of South Africa is host to the Kalahari Manganese Field (KMF). The northern portion of the KMF hosts high-grade manganese referred to as Wessels’ type ore and is mined mostly from underground operations. WorleyParsons TWP is currently involved with the development of a ventilation shaft for one of these mines. The main challenge is to develop through the unconsolidated Kalahari material and weathered portion of the Karoo formation. These formations are preserved very erratically over short distances. A lack of understanding of the unique challenges presented for developing shafts in this area has resulted in the failed development of a shaft on an adjacent property and over-expended budgets on others.The renowned red sand of the Kalahari forms the top several tens of metres and overlies a horizon of gravels and calcrete that pose seasonally variable water ingress problems. A very stiff red clay horizon is then intersected. The Red Clay is prone to swellling during excavation and has been the main stumbling block on previous constructions. The standard approach has been to develop non-stop through this layer. The red clay is underlain by another horizon of calcrete, gravel and conglomerate that marks the bottom of the formation. The top of the Dwyka Tillite (Karoo Formation) is usually highly weathered and has a distinctive yellow colour. The weathered tillite is highly susceptible to drying and becomes friable. At reef-intersection, the combination of subhorizontal bedding and joints with the dominant subvertical faulting results in potential wedge failures in the manganese and ironstone units.This paper describes the geotechnical issues identified during the planning of the ventilation shaft and the risks associated with development through the Kalahari and weathered Karoo Formations. A new approach to developing ventilation shafts in overcoming these challenges is recommended.CITATION:Steenkamp, N C, 2014. Challenges of developing a ventilation shaft in Kalahari and Karoo formations, Northern Cape, South Africa, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 81–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Sneddon A

Expansion of central production facilities at the Kutubu Petroleum Development Project in Papua New Guinea (PNG) required excavation of a steep hillside overlooking operating crude oil processing, storage and pumping facilities. Drilling and blasting were used to remove a large volume of rock which varied from hard limestone to soft sandstone, with zones of soft clay and many underground caverns. Similar ground conditions had made it very difficult to predict and control blast-ing results during previous excavation in this area.Special conditions of the project included restrictions on ground vibration levels at a high pressure oil pipeline and pump station within 100m of the blasting area, and a prohibition on any flyrock. As work progressed, some blasting was necessary with 20m of installations being constructed on the levelled project site. Thus blast design, drilling and charging were carefully controlled to avoid any incidents which could interfere with oil production or progress of the construction project.

Jan 1, 1994

By Wright J. K

A description is presented of the results of reduction experiments using a laboratory reduction apparatus in which simulation of the gas and temperature profiles which occur in direct reduction shaft furnaces is achieved using microcomputer control. The apparatus allows continously changing reduction conditions to be impressed on lump or pellet samples to simulate the environment that is experienced by iron ore burdens during their transit down the shaft of a direct reduction furnace. Three pellet samples and three lump ore samples were reduced in the apparatus. Comparative reduction curves and strengths after reduction for the materials were obtained over a range of reduction temp- eratures using Midrex-type gas compositions. The resulting reduction and strength curves show considerable variation in behaviour and reflect the physical and chemical variations in the individual ore and pellet types. A comparison is made of the reduction rates and modes of reduction of the samples reduced under "conventional" test conditions using a single unchanging gas composition and the simulated shaft furnace reduction conditions. It was observed that the course of reduction is very different in the two procedures and the major influence of temperature on the strength of the reduced product is noted.

Jan 1, 1987

The issue of flyrock is critical to the operation of all mineral extraction sites that use blasting. This paper takes a risk-based approach to identifying, analysing and managing the flyrock hazard. The basic cause of flyrock generation is a mismatch between the energy available and the work to be done. It should be noted that the energy available depends on the charge confinement. This mismatch can be caused by an abrupt decrease in rock resistance (geological weaknesses), overcharging, inadequate delays between holes and rows, inappropriate blast design and inaccurate drilling. The mismatch can come about from two sides; either too much energy (charge) for a fixed burden (work to be done), or insufficient burden (work to be done) for a fixed charge. The main mechanisms of flyrock generation are rifling, cratering, face bursting and secondary blasting. Each source mechanism has different characteristics in terms of vulnerable locations and each requires different control measures. However, all controls require a high level of quality control and assurance. A range of different approaches for managing flyrock risk and determining blast clearance zone dimensions are presented. A prescriptive consequence-based approach is discussed. A conventional risk matrix based approach is outlined with some innovation regarding controls rating and uncertainty ratings. A published semi-empirical approach is discussed. Two examples of quantitative flyrock risk analysis are presented; one involves bench blasting based on a published paper and the second is a cratering example developed by the author based on consulting projects. Finally, a stochastic approach based on published work is presented which simulates cratering superimposed on face bursting mechanisms. Also, a stochastic analysis undertaken by the author of the cratering example is presented. Effective blast emission management is required for two reasons; firstly to reduce and/or eliminate safety risks and secondly to manage public perception of blasting risks such as flyrock. The conclusion of the current research is that the wild flyrock risk can be estimated using existing techniques. Furthermore, both qualitative and quantitative risk management methods as discussed in this paper can be used for flyrock management for a given blasting situation. A combination of both is considered to be best practice.

Jan 1, 2007