Search Documents

Incompetent ore and country rock have caused stability problems in longhole open stopes. Fully grouted pre-placed cablebolts have reduced these by preventing ground relax- ation and joint dilation to maintain a self supporting rock structure. Larger atope spans can now be opened with the same or smaller pillar. Mining methods are expected to become less dependent on original ground conditions. Effect of spacing, orientation and stress distribution along the cablebolt is not fully understood at this stage and requires more Observation.

Jan 1, 1977

The care necessary to ensure a reliable estimate of average value from the individual values of a series of bore holes sunk in any alluvial deposit containing coarse gold was well exemplified in checking over the mining returns from a previously bored deposit in Central Otago, N.Z. While the working returns are always liable to vary considerably from bore values in any particular sub-section of an area, still, over any considerable area, the two must check within small limits, if profits are to be calculated and capital raised on the average value given by boring.The present figures have probably more value than those from, dredge returns since accurate measurements are difficult to obtain in irregular water-filled dredge paddocks, whereas in the case under review the paddock walls stood almost perpendicular, and, as the measurements were taken and checked in the empty rectangular excavation, the yardage estimate may be taken as substantially exact.NATURE OF DEPOSITThe area consists of a narrow valley deposit of fluvio-glacial origin, the original deposit having been eroded and the gold reconcentrated by post glacial rivers. The wash is between 80 and 90 ft. deep, and is formed in two distinct layers:(i.) The top layer from surface to 70 ft. or 80 ft. consists of about equal quantities of gravel mixed with glacial drift, and a small amount of clay. The gravel is typical discoid glacial stone of a maximum size of about 4 in. diam. by 1 in. thick, and consists of soft micaceous schist and laminated slate. This upper layer of wash contains no coarse gold whatever, and very little fine; indeed, in mining, the top 30 ft. is discarded without being passed over the boxes.(ii.) The lower layer of wash to bedrock is similar to the upper, except iihat it contains about 10% of larger discoid stone up to 12 in. diam. by It in. thick; 90% of the gold is concentrated in this bottom layer.

Jan 1, 1929

The results of the washing of coal are often presented by using Partition Curves. By analogy, it is possible to express the results of screening by using similar partition curves. As in the coal washing processes, this method determines the accuracy of screening and is also suitable for different separations depending on the difference in size distribu- tion. This method compares the effectiveness of two screening operations and forecasts the performances.

Jan 1, 1984

By Penny T. G

BHP Diamonds and their joint-venture participants DiaMet Minerals, Chuck Fipke and Stewart Blusson are currently developing Canada's first commercial diamond mine in the arctic barren lands of the Northwest Territories (NWT) of Canada. The paper reviews the early history of the project leading up to the discovery of the first kimberlite pipe in September 1991, diamond exploration techniques and the subsequent advanced exploration and development work carried out at the site. In many aspects, this exploration work represented a development project in itself. Coinciding with the advanced exploration work, the project team prepared an Environmental Impact Statement (EIS) and went through federal review of the project at the highest level. External affairs strategies regarding the federal review and aboriginal land claim issues were crucial components to the approval process. Upon approval in principle by the

Jan 1, 1997

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

Efforts to stabilize international markets in commodities have gradually intensified during the course of this century in keeping with the grow- ing complexity and interdependence of the world economy and the increasing involvement of government in economic activity. Successive Australian Governments have con- sistently supported the concept of commodity agreements and arrangements in an effort to lessen short term fluctuations in price and to moderate the boom/bust conditions which tend to charac- terize production and trade in many commodities. The objective is to stabilize price at a level which equates supply and demand over the life of the arrangement. Such action involves a degree of market inter- vention and government involvement in the inter- national trade in the commodity concerned; the acceptability and desire to foster such arrange- ments varies from country to country depending upon attitudes to market intervention and man- agement. However attitudes, even among those opposing commodity agreements, have under- gone a major reversal in this century. Before the first world war, such intervention as existed almost entirely involved the physical producers. There was almost no government involvement and at that level most regarded commodity agree- ments as neither desirable nor practical. However government regulation of such activities as pro- duction and marketing of food during World War I, coupled with post-war shortages, followed by overproduction and the crash in prices during the Great Depression, stimulated producer gov- ernment interest in commodity market regulation. Consumer governments took a little longer and with a few exceptions, it was not until the post World War II period, that the fear of shortages of basic commodities brought some consumer countries to accept the concept.

Jan 1, 1978

By Wagland D. G, Guo H

The Mt Whaleback orebody is in a complex geological regime. A good understanding of geological structure is essential during the design and implementation stages. The amount of information on the rock-mass condition available at the design stage is considerably limited. It is essential to validate the rock-mass properties used in the design during implementation. It is important to achieve integrity of the final pit wall during development and to maintain the integrity until the end of its designed life for safe and economical extraction of ore. The original geological model is updated by way of on-going detailed geological face mapping. Original design is reassessed and is modified based on any significant variations to the previously evaluated geotechnical conditions. Information gathered during design implementation provide tools for effective management of the pit walls. Controlled blasting techniques are employed in the final limits blasting. Presplit blasting is used in most limits blasts. Presplit helps to maintain the integrity of the wall by venting excessive gases from the limits blast. This helps to reduce bedding dilation by gas penetration. Also, it helps to define the design batter for the operators for final batter trimming. Pyritic shale needs special attention during blasting due to its reacting nature. Cablebolting is applied in selective areas to secure small-scale potential instabilities. During the development phase, pit wall monitoring instruments are installed. These instruments are used to monitor the performance of the wall during and after excavation of the slope.

Jan 1, 1995

By Hatcher MI

Exploration undertaken at Copley diapir has located several occurrences of oxidized supergene and primary sulphide copper mineralization at the margin of the diapir or in adjacent country rocks. The mineraliza- tion is related to carbonate-rich epigenetic solutions which moved along major structural features closely associated with the intru sive diapir.

Jan 1, 1975

The procedure used for Truck Maintenance is described systematically in this paper. Emphasis is given to manpower required, work facilities, daily maintenance and oil sampling procedure. Scheduled Preventative Maintenance Service, Electrical Service, Component Change, Truck Overhaul and Outside Contractors are also discussed. The system used, achieves the required results with an average haul truck availability in 1981 of 87.9 per cent. INTRODUCTION Situated on the Island of Bougainville, in Papua New Guinea, the Bougainville Copper mine nestles in a valley near the crest of the Crown Prince Range, between 600 m and 980 m above sea level. The mine is serviced by two towns, Arawa - an open town on the Coast and Panguna at the Mine Site. Currently Bougainville Copper operates an open pit mine removing an average of 198 000 dry metric tonnes of material per day (115 000 tonnes ore and 83 000 tonnes of waste) with a fleet of electric shovels and 154 tonne electric haul trucks.

Jan 1, 1982

By Yeliseyev AK, Shestakov AM

Comminution is the most power-intensive process in the technology for ferrous quartzite concentration. That is why improving comminution efficiency leads to the most appreciable economic effect on the concentration process. The trend towards reducing the lump size of crushed ore before charging the mill is considered to be of major importance in improving comminution efficiency. A considerable number of investigations have been performed in this direction. At the same time, a strong interest is also maintained in the increase of comminution efficiency due to optimisation of process taking place in the mill. Recently, investigations of the power intensity of the breaking process inside the mill have been carried out at the Krivoy Rog Mining Institute. It was ascertained that the routine conditions of comminution at a low mill ball charge ratio resulted in an unnecessarily high power consumption due to the force of impact of falling and milling bodies far exceeding the power required for comminution. For example, the power value for falling balls of 60 - 125 mm in diameter reaches 0.3 kNm, and the force and stress due to ball contact with the lining reaches 60 kN and 250 MPa respectively. These values exceed the force required for comminution by a factor of ten. Analysis of the mechanism of ore particle size reduction during comminution in the ball mill indicates that the size reduction is due to impact load, attrition load, and static load. The efficiency of size reduction is very low. During comminution in the ball mill, impact loads prevail and amount to 85 - 90 per cent of the total load. In this situation, not more than 10 - 15 per cent of destruction is due to attrition.

Jan 1, 1993

By C OÆKeefe, A Thomas

Boom time in the mining industry has presented mill operators with several unique challenges including the need for increased throughput while being constrained by a shortage of skilled labour and aging capital equipment. New instrumentation technology that provides reduced installation costs; no process down time for installation; and reduced maintenance costs and labour requirements; has been introduced to address the labour situation while maintaining production. This new tech- nology also enabled more accurate and reliable process measurements thus providing the capability for operators to maximise throughput with their existing capital equipment. This passive SONAR based technology can accurately measure the volumetric flow rate of single phase and multiphase fluids as well as the amount of air entrained within slurries. This is accomplished in a non-invasive manner. This paper will describe the principle of operation as well as the application of the technology to critical minerals processing applications. Included will be operational examples comparing the SONAR measurement performance to traditional measurement techniques. These examples will include hydrocylone feed flow, flotation concentrate flow, and slurry streams containing magnetic ores. Actual plant data will be presented as well as a discussion on the operational advantages such a measurement capability.Also described will be the power of the technology platform to provide novel process monitoring and control capabilities such as pipeline sand-out prevention and pipeline acoustic monitoring.

Jan 1, 2009

By P Church

What is the best method of splitting a sample from a reverse circulation drill rig? How important is it to obtain a correctly split sample? What is the impact of an incorrectly split sample? These are just a few of many questions asked daily in the mining industry with regard to sampling. Modern sampling theory is well described in the literature in texts and is taught in short courses throughout the world, however little has been published on the relative performance of sample splitting devices used in the field. This paper compares the performance of the Jones tiered riffle splitter with a cone splitter manufactured by SGS Metal Craft in Western Australia. The testwork was carried out at AnglogoldÆs Sunrise Dam Gold Mine, 55 km south of Laverton in Western Australia. Mineralisation at Sunrise Dam is hosted in a structurally complex framework of shear zones with dips that range from steep (70¦) to shallow (25¦). The deposit is characterised by significant amounts of coarse gold, which presents a challenge in sampling, analysis and grade estimation. The three major areas where sampling errors can occur are in drilling, sampling, sample preparation and analysis. Sampling errors attributable to drilling and sample preparation often far outweigh the errors made at other stages in the process, however historically most effort to identify sampling errors has concentrated on the laboratory and analytical procedures. Splitter design and cleanliness can have a large impact on sample collection and preparation. Splitter performance was tested with respect to sample weights, particle size distribution, and gold grade consistency. The aim was to determine if each particle has an equal probability of being sampled, the resulting sample has integrity, and if any segregation problems occurred. The cone splitter was found to provide the best split in terms of particle size distribution, with no apparent size bias. Duplicate samples had more comparable masses than those provided by the riffle splitter. Most importantly, the cone splitter gave less grade variability between duplicate samples than the riffle splitter. Testwork also confirmed that, like the riffle splitter, the cone splitter must be oriented vertically and the design of the rig or cone splitter trailer should accommodate this requirement.

Jan 1, 2003

During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within North America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The traditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

Jan 1, 2005

Ranger Uranium Mines (RUM) operates an open cut located in the Top End of the North- ern Territory. Strict environmental controls govern all operations and the water management requirements have the greatest impact on mine planning. The two main goals of planning are to provide mill feed and to mine sufficient suitable quality waste rock for ongoing con- struction of the tailings dam. Early planning concentrated on staged development of the pit to provide access to as much ore as possible for a given amount of development. All waste was considered to be suitable construction material. Grade control of crusher feed was the main problem in planning, as wide vari- ations occur in ore grade over relatively short distances. Water management for the site ope- rates a no release' system for contaminated waters. Design storage has proven inadequate, and the open cut has been used as the extra storage. As construction of future stages of the tailings dam requires non-mineralised rock materials which meet specific quality criteria, the mine has had to re-examine long term plan- ning and pit development strategies. This has entailed the collection of much data not re- quired under normal mining conditions, such as the assaying of waste drill core. The overall impact on mine planning of the environmental regulations has been to alter the philosophy of earlier planning, making it necessary to create a new strategy for pit development with

Jan 1, 1984

By D V. Boger

The use of chemical additives to initiate such processes as particulate separation through flotation or dewatering through flocculation, is common in the mining industry. The dosing of additives is none the less poorly controlled from a process control viewpoint and it is perhaps fortuitous that over-dosing or misuse of chemicals is rarely catastrophic to the production cycle. In many cases, such events would go undetected if it were not for economic considerations. Recently, the advent of orebodies with finer mineral disseminations and the push for greater efficiencies in both production and tailing disposal have resulted in the need for greater control of the dosing and utilisation of chemical additives. The need to grind at higher pulp densities and to finer sizes and to dewater to higher solid contents are but two examples that require a more stringent understanding of the true role of additives in controlling the rheology of suspensions and the influence of additives on the surface chemistry of particles. The inter-relationship between the surface chemistry of particles and the role of additives in controlling suspension rheology is now well understood for systems in which the average particle shape in the mixture is spherical or close to spherical. Luckily, this is the case for a large number of systems in the mining industry and the true role of typical additives in these systems will be explored. Difficulties arise for suspensions containing clays or other platey or needle shaped minerals and in many cases, quite small quantities of platey minerals dominate the rheology of suspensions. The role of additives in controlling the rheology of asymmetric particle systems is more complex but the effect of the additive in changing particle alignment in solution is the key to understanding suspension behaviour. The manipulation of the rheology of asymmetric particle systems will also be explored.

Jan 1, 1998

By Mitchell G, Clarke C

The high oas emissions which are associated with high production lonowall mining have provided a need to investigate the limitations and reouirements of the various gas control methods. The major relationships between oassiness and various other parameters are presented with computer analysis being adopted to assess the respective correlations. Some of the relationships are studied in detail with emphasis being placed on methods for overcomino the changes in conditions resulting from high production levels. The importance of the various drainage systems which can be adopted to combat high gassiness levels are analysed. Logical and necessary steps are also proposed for gassiness prediction and data monitoring as well as various combinations of gas drainage systems. The gassiness prediction methods which are discussed outline the need for a sound knowledge of the established worldwide methods together with a comprehensive study of the local mining and geological environment in order to develop a system which is adaptable to the changing conditions. This is particularly important in mines where high coal production levels are anticipated and the need for accurate gassiness relationships is essential.

Jan 1, 1988

An empirical kinetic model is discussed that enables the number of stages in a carbon-in-pulp plant and the amount of carbon in each stage to be calculated for any desired metallurgical performance. It is shown that a knowledge of the kinetics of gold extraction by activated carbon in each stage assists plant operators in the important' areas of process control and optimization. Factors such as mixing efficiency, concentration and distribution of carbon through the plant, bypassing of pulp through a stage, and carbon poisoning are examined. The resin-in-pulp process for the extraction of gold cyanide is also discussed, and the chemistry of absorption and elution on strong- and weak-base resins is examined. In addition, operating results from a small-scale resin-in-pulp pilot plant are presented, and various applications in which resin-in-pulp may be preferable to carbon-in-pulp are discussed.

Jan 1, 1982

This paper reviews the role of fill in mining including consolidated fill both histor- ically and currently as determined by a recent survey of the Fill Subcommittee of the Canadian Advisory Committee on Rock Mechanics (CACRM). It covers the application of fill in modern min- ing methods including mechanized cut and fill, undercut and fill, post pillar cut and fill and longhole pillar recovery between stabilized fill. An automated fill preparation plant and recent developments in rotary drilling of hydraulic fill conducting holes are described briefly. The paper also summarizes the findings of some of the important laboratory and field work carried out on the behaviour of fill in Canada, the United States and Australia and again draws on current information obtained from the Fill Subcommittee of the CACRM. Space limitations and unavailability of suitable material prohi- bit the summary of similar information from other countries.

Jan 1, 1973

By J Emslie

Newmont AustraliaÆs Callie Underground Gold Mine is located on the Dead Bullock Soak Mining Lease, approximately 600 km NW of Alice Springs, NT, in the Granites-Tanami Goldfield. Dead Bullock Soak is part of NewmontÆs Tanami Operations, which also include the Granites Gold Mine and processing plant, Groundrush Open Pit and Tanami Mill. Callie is a world class Proterozoic gold deposit; production to date is in excess of 1.7 million ounces, with an additional Proved and Probable reserves at the end of 2002 of 10.8 Mt at 6.3 g/t. Gold mineralisation at Callie occurs in thin (1 - 30 mm) steeply dipping quartz-chlorite sheeted vein system that cuts across a 40¦ plunging folded sequence of medium to fine-grained metasediments. While the vein system is highly continuous, the gold distribution is highly variable and is controlled by the interaction of lithology, alteration, structure and vein density. The mineralisation is commonly coarse-grained and has a relatively high nugget effect, consequently the orebody is problematic to estimate and shows a high degree of sensitivity to drill hole density. Resource modelling at Callie is an example of a geologically driven model that has evolved with increasing data and understanding. Lithological and structural models are employed to define domains within which the grade estimation is undertaken using multiple indicator kriging. This gradual model evolution impacted greatly on the selection of the mining method. Uncertainty in the estimation of the orebody was a significant factor that led to sublevel open stoping with cemented aggregate fill being adopted as the mining method to improve extraction selectivity. Callie often shows strong positive reconciliation compared to the mill. The mine geologistÆs face the challenge of limiting the degree of underestimation of the core of stopes whilst ensuring that stope boundaries are not conservative. This can only be achieved through the mapping of subtle geological features in order to confirm the orebody model. The increased use of the geological mapping has improved our understanding of the controls on mineralisation and has been extended into the development of new models for near mine underground exploration.

Jan 1, 2003