Search Documents

Over a four year period from 1984 to 1987, a broad range of ground conditions were experienced in recovering old workings at the Walhalla mine in central-eastern Victoria. Access to the ore zone was gained via old workings and new development. The work included: Recovery of vertical and inclined shafts. Recovery of collapsed winzes. Recovery of level drives and crosscuts. Spiling through broken ground and old mullock. Pre-grouting of caved zones. New development using small-scale rail equipment and "bobcat" Loaders.

Jan 1, 1988

By Sterns UJ, Weller KR

Grinding to sizes less than 80 per cent passing 20 ¦m in both primary and regrind circuits is becoming increasingly important in processing metalliferous ores, as many of the remaining orebodies are very fine-grained and refractory. The process of very fine grinding, however, is expensive, and neither the performance nor the design criteria are well understood. This paper presents some findings from a collaborative research program, one of the objectives of which has been to better understand and improve the performance of very fine grinding circuits. Data from surveys of an industrial tower mill grinding circuit are reviewed and analysed using the population balance models of the CS]RO and 7KMRC. The performance of both models with regard to changes in feed size distribution, ball load and feedrate is assessed using these data. From comparisons between pilot and full scale tower mill operation a prototype scaling methodology is also presented which shows promise in allowing the models to be used to predict the effect of changes in mill Design.

Jan 1, 1993

By D G. Miljak, J Khachan, B K. Schwitter

The performance of prototype magnetic resonance sensors suited to mineral measurement in conveyor, slurry or portable applications is described. The sensors can be positioned around conveyors and modified slurry pipes, providing deep penetration of the sensing field, relative insensitivity to ore surface conditions and high mineral discrimination. Measurements on slurry, concentrates and ores sourced from mine operations are presented for two applications. Firstly, the quantitative measurement of chalcopyrite in slurry was demonstrated in laboratory measurements. In a calibration test, a standard error of 0.1 wt per cent and detection limit of 0.3 wt per cent was obtained. Secondly, results were obtained for the discrimination of iron ore texture. Signals were readily observed using measurement integration times of seconds to several minutes, depending on ore material. The results demonstrate the feasibility of online quantitative analysis of selected minerals in processing applications using magnetic resonance.

Jan 1, 2008

FINANCE FOR EXPLORATION Two factors have basic importance in relation to the availability of finance: the apparent success of continuing exploration activity and tax concessions. It is not proposed to discuss the effect of existing tax incentives, as these have already been outlined and are generally accepted as being reasonably attractive; certainly not a deterrent to possible investors. However, it is obvious that the greater the tax incentives, the greater the amount of money that will be attracted, and the wider the number of people who can be brought into the pool. If, as is suggested, the chance of discovery is related to expenditure and effort, then the more money attracted, the better the prospects of significant finds. It is probably correct to assume that the largest expenditure in mining will come from, or be induced by, people expert in the field, people who are fully aware of the risks and benefits and perhaps making conservative decisions because of this awareness. Insofar as the general public is concerned, while in the first burst of enthusiasm it will frequently follow any promoter, in the long run it too will become more sophisticated and will strongly support only those promoters and companies of good repute and proven record.

Jan 1, 1971

Since 1975 two electric hydraulic drills, a Robbins 11ND and an Atlas Copco C0P1038, have been part of the production drilling fleet at Mount Isa Mines Limited's Isa Mine. As might be expected with innovative and technically more complex machines, breakdowns and mainten- ance problems have been greater than those experienced with pneumatic drifters. This has been especially so with the COP1038 but in co-operation with Atlas Copco, many modific- ations have been made to alleviate operating problems. The training and quality of the maintenance workforce is of great importance. The use of coloured pictorial diagrams for hydraulic trouble-shooting will aid in minimising maintenance downtime. Both machines have achieved good operator acceptance. This is the result of many factors, the major ones being the more acceptable environmental conditions, the relatively low amount of physical effort and the high degree of mechanisation. The drilling area is one in which there is great potential for cost savings and product- ivity gains. Because both machines are capable of a high drilling output, Isa Mine is confident of achieving these aims.

Jan 1, 1978

By Anderson DR, Tassell G

A major environmental impact study carried out in the sand dunes of eastern Cape York used image analysis of remotely sensed data to both select sites for ground investigation and categorise the different ecological units present. The approach adopted was particularly suited to the type of environment in question and allowed a high degree of quantification, at a high level of confidence, at costs several orders of magnitude less than conventional Methods.

Jan 1, 1987

Both innovation and excellence are desirable attributes of education, as they are also markers in the progression of the human race, but how attainable are they? The interaction of minerals and humanity provides a special insight into the development of both criteria, from the discovery that chert cuts, through the Bronze Age and the first use of metal alloys for implements, to using coal, oil and uranium as sources of fuel. However, there have been many hiccups along the way, where excellence in one respect has meant disaster in another. Examples are in the exploitation of asbestos, and in traditionally poor work practices in mining, both contributing to the widespread public belief that minerals and mining are ecologically undesirable. Yet is this perception based on the unrealistic expectation of innovation and excellence being simultaneous qualities of any given process? Common sense born of experience indicates that the journey from one, to the other, is usually a long and often tedious process, with much trial and error before excellence is attained. In our time, the partnership between academia and industry is the usual pathway to achieve it. Even so, we should take care that innovation does not become overwhelmed by the pursuit of excellence: as history clearly demonstrates, humanity depends upon both.

Jan 1, 2004

Industrial minerals and rocks (alternat ively called non-metallic minerals) are those- which are economically important because of their desirable physical or chemical properties rather than their metal or energy content. They are divided into nine classes: structural, pig- ments, process aids, ceramics and refractories, chemical source minerals, abrasives, foundry minerals, gem stones, electrical minerals. Development of deposits is influenced by the dominance of marketing,by the required range of products, the-need for specialized process- ing, place value, and the transportation and distribution of high-bulk, low-cost commodities. Evaluation is different from that of base metals because of differences in geological occurrence, sampling methods, testing, treatment, placing a money-value on the material and the importance of export markets.

Jan 1, 1973

By Reimer TH

The model described in this paper has been developed for and in close collaboration with the Bong Mining Company Ltd, Liberia/West Africa. When working an irregular deposit a de- tailed short term production schedule becomes necessary in order to ensure an equal and homo- genous concentrator feed. If the irregularity of the ore body exceeds a certain degree, blen- ding facilities have to be provided between the mine and the concentrator, but even then sche- duling of the mine production is inevitable to meet the given requirements of the blending bed and to keep these conditions steady for at least some of the successive periods. To assist the planning department in set- ting up optimal production schedules a computer model has been developed using a linear pro- gramming approach. The deposit is divided into equally shaped blocks containing defined quali- ties and quantities of ore and/or waste; from which one has to select those quantities of ore which will meet the requirements of the blen- ding bed. The objective function of the model

Jan 1, 1977

By Kennedy B. J

The 1100 Orebody is the main copper production area of Isa Mine with an output of 390 000 tonnes per four week period and a work force of approximately 260 men per shift. Currently a total of 56 nippers work a three shift, five day week roster to-service crews spread over a strike length of 1000 m and a vertical height of 220 in. A variety of rail and diesel equipment provides shaftto cribroom and cribroomto sublevel work place transport of men and materials. Overall eficiency and safety has been improved with a selected group performing supply, storage, clean-up and "bus runs" throughout the orebody - activities which are further co-ordinated by an FM radio system linking units with a control clerk.

Jan 1, 1977

Victorian brown coals occur in massive deposits, the quality of which is determined in the first instance by means of samples taken from exploratory bores. As a number of important utilisation characteristics are connected, not with the relatively homogeneous organic mass of the coal, but with minor components such as the ash content and particular constituents of the ash, it is necessary to know how bore samples relate to coal finally used in the process concerned. Tests are described in which the statistical parameters associated with bore sampling, operational sampling and sample reduction and laboratory procedures including a range of coal analytical methods were determined. These indicated properties where analytical errors were relatively high and where sample reduction procedures contributed substantially to imprecision in results. They also showed the effects of the non-homogeneity of brown coals with higher than normal ash contents. A further experiment explored the relationship between samples taken at various stages in the course of test boring, digging, and burning a defined 'block' of coal, and demonstrated an apparent increase in the proportions of adventitious mineral constituents as the 'intensity' of sampling Increased.

Jan 1, 1976

By D S. Terekhov, N Victor, M F. OÆMeara

The current extraction method of the Platinum Group of Metals (PGM) from an ore concentrate and the subsequent separation of one PGM metal from another is a timeconsuming complicated multi-step process. The use of the Chemical Vapour Metal Refining (CVMR) process for the extraction and separation of PGMs is a simple and economical alternative. The paper covers the CVMR process, which is based on the formation of volatile metal compounds, followed by extraction and thermal decomposition into the pure metals and reagent gases. In the case of PGMs, CVMR does not use CO, and hence, the process is quite different from the carbonyl process previously attempted by a number of organisations and test facilities. CVMR extracts PGMs via synthesis of trifluorophosphine complexes at low pressures and low temperatures (80 to 100¦C). These two facts alone make the process highly economical, compared to other methods available. This paper presents a comparison between the process of extraction of PGMÆs and CVMR proprietary carbonyl process for the extraction of nickel and cobalt. In the carbonyl process, CVMR also uses very low pressures and temperatures, compared to those other processes currently use.

Jan 1, 2002

By Lane G

This paper addresses project commissioning, that is, activities that culminate in the transfer of a project from the construction phase to routine plant operation. These activities should be initiated early in the engineering and design phase to ensure that the plant design is operator friendly and that construction is scheduled such that pre-operational testing and hand over to the owner occurs in a timely and cost-effective manner. For the purposes of this paper, commissioning includes all activities related to pre-operational testing, no-load testing, water commissioning, and ore commissioning. That is, all activities from construction completion to practical completion of the prime contract. This process is facilitated in numerous ways dependent on the nature of the project prime contract and the size of the project. For small lump sum projects, the contractor's responsibility may include all phases of commissioning to practical completion, whereas, a managing contractor on a complex multi-contract project may only be required to bring the project to mechanical completion and hand over to the owner for ore commissioning. Irrespective of the responsibilities, commissioning programs require careful planning, effective communication and detailed reporting. Unsuccessful

Jan 1, 1997

By Armstrong RW, Middlin B

The development, design, construction and operation of the new Solvent Extraction/BCA process plant at Copper Refineries Pty. Ltd., Townsville is described.The process offers substantial savings in electrical power costs, improvements in plant hygiene, and a lowering of materials handling costs compared with conventional electrowinning technology.The solvent extraction process extracts arsenic from copper Tank House electrolyte using a tributyl phosphate (TBP) - kerosene solvent. The plant incorporates fourextraction stages, two scrub stages, and three stripping stages to produce an arsenic-bearing low-acid strip liquor. This strip liquor is mixed with copper sulphate, and neutralized with ammonia to form a copper (II) arsenic (V) crystalline product, bicupric arsenate (BCA). This product is then used in the manufacture of chromated copper arsenate timber preservatives (Royston 1982).

Jan 1, 1985

The aim of all modelling is to replicate geological reality as closely as possible using available data. This paper is aimed at one end of the spectrum, where very limited data is combined with intuitive geological ideas to synthesise models for either target definition or for determining minimum viable mining scenarios. Interactive 3D modelling allows a satisfactory hypothetical geometry of surfaces to be assembled, and provides a fast quantitative method for generating targets. As data flows from exploration, an evolving geological model assists with the progressive evaluation of a prospect. Two case histories are described where this approach has been used successfully, the Mosquito Hill Prospect in Queensland and the Longwood Ranges Platinum Prospect in New Zealand. The possibility is also discussed of hypothetically modelling an orebody which has yet to be discovered. The proper description of an orebody is the foundation upon which all mine design and planning is undertaken. The volumetric accuracy of the model is crucial in valuing an orebody. Geologists must form a geometry which matches the conceptual view of the ore occurrence and ensure that they understand how the computer system used calculates volumes. If the underlying assumptions inherent in the method conflict in any way with the conceptual model visualised for the ore occurrence, then that method must not be used.

Jan 1, 1995

By E House, V Lisitsin

Recent whole-rock geochemical data from nearly 900 fresh drill core and underground samples taken from seven central Victorian gold deposits confirm the presence of distinct and identifiable primary alteration haloes surrounding the deposits. Ferroan carbonate alteration extends for up to several hundred metres away from turbidite-hosted gold mineralisation outside of contact metamorphic aureoles. A less distinct phyllic alteration zone can be identified using geochemical molar ratios or short wave infrared analysis. It generally overlaps a sulfidic halo characterised by disseminated pyrite and in close proximity to mineralised structures, arsenopyrite. The extent of the sulfidic halo can be traced using low-level analysis of pathfinder elements such as S, Au, As and Sb. Recognition of these alteration features enlarges the target for exploration and provides a tool by which drilling can be directed towards mineralised structures. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The use of ammonium nitrate/fuel oil explosives is.now well established in most open cut mining operations. Its use. is extending to underground mining. This has been due in a large measure to improvements in the nature of the ammonium nitrate made available from various sources. The addition of surface active agents and water in controlled amounts to the fuel oil has been found to increase the sensitivity of the ANJFO mixture with consequent better explosive properties. It is considered that the surface active agent increases the bond between the ammonium nitrate and fuel oil giving a more, intimate physical and chemical mixing of the oxidising and reducing agent. This results in increased sensitivity and a faster rate of reaction. The increase in sensitivity has been accomplished without any diminution of safety. Tests which demonstrate the safety of this type of explosive are given in the appenuix.

Jan 1, 1964

By M Warren

The professional geologist or engineer on a mining operation has a particular view of their operation. This is based on the factors of the operation that have a direct impact on the daily work program of the professional, such as production rates and grades. The view that would be taken by a financier who is called upon to support the project may be somewhat different. The value of the operation to the financier is in its ability to generate surplus cash for its owners and thus repay the debts to the financiers, with as low risks profile as possible. A number of tools are used to test the sensitivity of the project to variations in the key cost/revenue drivers. The Financier may call on a team of technical specialists to assist with the assessment of the cash flow and risk profile and to monitor the development of the project. The ability to offset this risk, as all projects have some degree of risk, may be a key factor in determining the level of financial support to be offered.

Jan 1, 2002

By M D. Boscardin, P A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County involves TBM tunnelling twin light rail tunnels through cohesive soils and rock under the Allegheny River and a narrow city street. Along the tunnel alignment are a listed historic building on shallow foundations as well as modern buildings on deep foundations; one major office block was actually constructed directly over the alignment during the latter phases of design process. This paper provides an overview of the general site conditions, tunnel design and the technical basis for excavation support and tunnelling decisions. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed. Project construction has now commenced and a brief summary of progress to date is included in this paper; this will be updated for the presentation to be made in Melbourne.

Jan 1, 2008

By R M. Briggs, I E. Smith, P M. Black, A B, R L. Brathwaite, J L. Mauk

The Hauraki Volcanic Region of the North Island developed between 18 and 1.9 Ma. Initial andesitic volcanism from 18 to 12 Ma was followed by 12 to 1.9 Ma volcanic activity that included rhyolitic, dacitic, andesitic, and basaltic compositions, with a gradual migration of activity to the SSE. Early andesitic volcanism evolved over the course of 8 m.y. to more silicic compositions; this trend was reset and repeated by post-10 Ma andesitic volcanism. Early and later andesites are otherwise remarkably similar in trace element composition. Rhyolites have the most diverse compositions, suggesting a major role for crustal input in their formation.

Jan 1, 2007