Search Documents

By Clark K. N

The need for and advantages of simulators in iron ore pellet induration research are described. The approaches to simulation and the techniques to carry it out are discussed in detail covering drying and firing for the straight grate process. The CSIRO simulator design is described and some errors in simulation are discussed.

Jan 1, 1974

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

By Madgwick J, Pracejus B

The microbial, microaerobic, biodegradation of cryptomelane-rich and pyrolusite-rich samples of manganese oxides was studied in repeated five-day static batch cultures over II weeks. Manganous ion was leached/reduced faster from the cryptomelane-rich samples (average 510 mg Mn2+/1/d) than from the pyrolusite samples (average 442 mg Mn2+/1/d).Cultures contained 20 per cent (w/vl) manganese mude, five per cent (w/v) molasses nutrient and the end-of-batch bacterial cell numbers were approximately 1010 cells/ml. The cryplomelane-rich sample incubates became more acid with time than the pyrolusite-rich incubates. The breakdown of pyrolusite proceeds in a relatively uniform way, while cryplomelane indicates a stepwise destabilisation.

Jan 1, 1992

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

By Haigh C. J

A process has been developed to recover at least 75% of the 2-naphthol contained in cobalt precipitate produced during the removal of cobalt from electrolytic zinc plant solution. The recovered material is in a form suitable for recycling to precipitate further cobalt from solution. The process consists essentially of two steps. The first involves leaching of cobalt precipitate in 400 g/l sodium hydroxide solution at 95¦C in the presence of an additive. The second step involves treating the filtrate from the leaching stage with sodium sulphide to precipitate cobalt as the sulphide thereby re- generating the sodium hydroxide for recycling. The process is only marginally profitable at present 2-naphthol prices, giving a net return of 20% on a capital investment of $1 200 000. A reaction mechanism is proposed which accounts for the 25% loss of the 2-naphthol in the recovery process.

Jan 1, 1977

By King D, Dickinson S. B, Matheson R. S

Graham Hall and V. M. Cottle (Rosebery, Tas.) : In their paper on "The Mineralized Rift Valleys of Tasmania", Campana, Dickinson, King and Matheson have summarized a wealth of data from many sources. In proposing the new concept of a rift valley structure, they claim to have found a new guide to regional ore control and distribution in North-west Tasmania.Although the authors acknowledge suggestions made by us prior to publication of the pa:per, we are still at variance with their conclusions. We are not convinced that a rift valley structure exist~d when the Ordovician conglomerate was deposited. We are unable to find evidence for Cambrian deposition in a rift valley or reason to project the structure to embrace Hercules, Rosebery, and "possibly" Mt Bischoff.That the Great Lyell Fault (the authors' Owen Rift Fault) is a promising place to look for ore is not a new idea, but the existence of important ore deposits away from the structure reveals its inability to provide an adequate explanation of regional mineral distribution. A well-known structure that does have an influence on ore deposition is not discussed by the authors.STRUCTURAL CONSIDERATIONSThe great thickness of coarse unsorted Ordovician conglomerate lying in an elongate but narrow belt of country is presented as evidence of its deposition centrally within a rift valley, the position-of which is now said to be outlined by resistant slabs of the conglomerate. The marginal shears of the rift are said to show up well along the edges of the conglomerate.

Jan 1, 1959

By Y Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, aO2-, and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of aO2-, which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions.

Jan 1, 2000

May I first of all say that I am fully conscious of the great compliment paid to me when I was invited to accept the Presidential Chair for this current year. I realise that it is an onerous task by reason of the fact that the Chair has been occupied in the past by so many able and distinguished men, and I realise also that I have been set a standard which is hard to emulate. "It is my desire however, in accepting the post that I may be able to contribute in some small measure to the further advancement Of the aims and objectives of the Institute and I thank you all for the confidence you have shown in me.Secondly, on behalf of the Company and in my Presidential capacity, I want to extend to each and everyone of you a hearty welcome to Whyalla and I hope that you will all return to your respective fields of endeavour feeling that you have had a most interesting, enjoyabIe and instructive time with us here in Whyalla.In this year of 1951 marking as it does the culmination of the first 50 years of Federation in Australia and yet another half century of human endeavour and progress, we are brought to a point where it is perhaps natural that we should pause, to review what has been achieved, in that span of time, and to look at the tasks ahead.It is no exaggeration to say that the story of Australian development since the inauguration of the Commonwealth 50 years ago has no more remarkable chapter than that of the-growth of its manufacturing industries.Each decade has borne witness to steady and substantial growth of our secondary industries and whilst it is true that our financial well-being still rests heavily on our primary production, we have, as a nation, moved surely in the direction of a more balanced economy. More and...

Jan 1, 1951

Many parameters are important when considering the performance of a concentrator. These include metallurgical performance, such as throughput, metal recovery and final concentrate grade and operating costs, such as power consumption, water usage, reagents and spare parts. In most operations the objective is to maximise metallurgical performance and minimise operating costs, ideally without a large investment in new capital items. A number of projects have been carried out at Newcrest MiningÆs Cadia Valley Operations (CVO) with the aim of improving metallurgical performance and minimising operating costs. This paper focuses on the installation of newly designed flotation mechanisms in various cells in the Cadia flotation circuit and describes the effect these changes had on performance and operating costs.

Jan 1, 2009

By Maconochie A. P

The copper-gold orebodies of the Ok Tedi project and located in an area of climatic and topographic extremes, where both the landforms and the rocks from which they have developed are so young that it may be said that geological and engineering processes are coincident.

Jan 1, 1990

By Rogers R, Kinnane T

In a typical open cast mining operation, investigation of how existing truck performance compares with the highest achievable truck performance is largely neglected. This paper addresses this issue by proposing a computerised system that will provide a systematic method for comparing existing truck operational performance to the highest performance considered achievable. Through analyses of existing versus achievable performances, various inefficiencies associated with truck operations can be identified. These inefficiencies could occur due to machine configurations, haul route design and conditions or operator skill level. Remedial action should then be taken in a timely fashion to better manage these factors and to ensure the fleet is always operating at its peak efficiency.

Jan 1, 1994

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electro- lyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions. The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was invest- i,ated as a method of optimizing glue additions in the presence of antimony. Scanning electron microscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltammetry measurements showed some correlation between current efficiency and activation polarization potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1984

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

It is now 32 years since Walsh's classic publication (1) heralded the beginning of atomic absorption spectrophotometry (AA) as we know it today. During this time, AA has developed into the most widely used analytical techniques for the determination of the metallic elements. The years have seen progressive changes in instrumentation so that today it is a highly sophisticated technique. One area of development in AA that is experiencing renewed attention is in the area of electrothermal excitation. In this technique a flame is not used by the analyte solution is atomised by an electrically heated graphite furnace. For a large number of elements the graphite furnace atomic absorption spectrophotometer (GFAA) is considerably more sensitive than flame work. It is common to be able to detect concentrations one hundred times smaller than those possible by flame. Today's geochemists are finding that they can gain valuable information out of very low limits of detection. Electrothermal atomic absorption spectrophotometry (or GFAA) allows for low limits of detection and can be seen to be a valuable aid to geochemical prospecting Analysis.

Jan 1, 1987

By Unver B

Longwall advance mining is still the predaninant system of coal extraction in the U.K., contribiiting to sane 70 % of underground coal production. Gate roadways providing access to a longwall advancing coal face are maintained adjacent to a rib pillar under high strata abutment pressures and the caving rock mass. It is very difficult to realistically model such access roadways using mathematical or numerical techniques and hence, predict roadway closure. For the past 15 years, a research group in Nottingham University has been engaged in the study of longwall gate roadway stability using observation methods. Gate roadway deformations have been measured in 224 gate roadways and a comprehensive data base has been established. The paper describes the statistical analysis of this database and presents sane. predictive equations which will enable a forecast of the gate roadway closure to he made. Further field work to validate these equations. is described together with an error analysis. The results are very promising and indicate that it is possible to predict gate roadway closure in the U.K. within practical limits of Accuracy.

Jan 1, 1986

By Forsythe DJ, Sun S-S Andrew AS

Paragenetic, fluid inclusion, stable isotope, and 87Sr/86Sr and 143Nd/144Nd isotope studies of the Mt Carbine tungsten deposit in North Queensland provide information on the sources of the mineralising components and record the history of fluid-rock interaction during the hydrothermal process. The ore minerals , wolframite and scheelite , are contained in quartz veins which post-date the major deformations in the Siluro-Devonian Hodgkinson Formation . Mineralisation was immediately preceded by the emplacement of the Mossman Batholith (280 ¦ 7 Ma). Two major stages of mineralisation are present and separated by a brittle fracturing episode . The stable isotope and Sr and Nd isotope data suggest that the ore fluids during stage I and most of stage II mineralisation were a mixture of magmatic water and non-magmatic water (connate or metamorphic) which had experienced a long residence time and had extensively exchanged with the sediments at high temperature. Subsequent mineralisation events were dominated by fluids of meteoric derivation with a short residence time. The data imply that other solutes, such as W, were probably derived in minor part from local country rock sources with the major contribution coming from a magmatic source related to the granite batholith.

Jan 1, 1987

The Permian coal in the Muja Coal Measures of Collie Basin of Western Australia has a subdued lustre because of the fine laminations of lithotypes, and the dominance of dull and dull banded lithotypes with minor bright, bright banded and fusinous types. The maceral composition of the coal is variable, however the macerals of vitrinite and inertinite groups dominate and the exinite and mineral matter contents are low. The lithotypes have low concentrations of trace elements and the boron concentration is between 10 - 100 ppm recorded only from the dull lithotypes. On the basis of organic petrology, the inter-seam sediments, flora and the very low concentration of boron, the depositional environment postulated for the coal is braided, fluvial and fluvio-lacustrine with marked fluctuations in the water table. The low water table in the environment accounts for fusain and inertodetrinite in the coal.

Jan 1, 1996

By Pala J

The Ellalong Colliery has been the first to mine the Greta Seam using the longwall method. Analysis of data from geotechnical monitoring has pointed to the role of the strong, massive sandstones of the Branxton formation in the development of loads on the powered supports and pillars. Failure of the sandstone intermediate-roof has been related to first-weight and periodic weighting, measured on the supports, using simple "voussior" analysis. Stress changes, including triaxial components measured in the barrier and chain pillars, have been compared with 2- and 3- dimensional numerical models. The applicable range of the models for the prediction of pillar loads under the strong roof is discussed.

Jan 1, 1986

By Wu H. W, Jones S. J

Australia wide, over 40 fly-in/fly-out mining operations and other forms of long distance commuting now exist, with coverage of about 5000 employees. The substantial majority of these operations are in Western Australia, with some mines also located in Queensland and the Northern Territory. In recent years new large-scale mining operations have adopted the fly-in/fly-out approach and it is important to note that no new mining towns have been constructed in Australia since the township of Roxby Downs was built in the late-1980s to service the Olympic Dam mine. An examination of fly-in/fly-out mining operations in Australia has been undertaken. A detailed survey undertaken in 1990 has been reviewed and another intensive survey undertaken to establish emerging trends. Results from both company and individual employees point of view have been analysed. A section examines the views of professional employees and the influence of fly-in/fly-out on career development. Bus-in/bus-out coal mining operations are emerging in Queensland's Bowen Basin. These operations commute their employees into the mine site for compressed working schedules while the mine employees' families are domiciled in regional cities such as Mackay. A review of the issues associated with the development of long distance commute coal mining operations in Queensland's Bowen Basin is performed and two case studies examined.

Jan 1, 1997

Peko Mines, a Division of Peko-Wallsend Operations Limited (PWOL) has operated several small underground mines in the Tennant Creek district of the Northern Territory supplying ore to a central treatment plant. The Argo Mine is the most recently developed by Peko Mines. A magnetic anomaly was identified from low level airborne magnetics in 1960 and drilling, which commenced on the site in 1969, was halted in 1974 and resumed in 1980 following the rise in the price of gold. By mid 1983 a resource of + 200 000 tonnes of 12 g/tonne Au had been outlined and a decision to develop the resource was taken following the drilling of three further diamond drill holes which did not significantly alter the value of the resource. The small size of the orebody could not support the full capital cost of two shafts and a single entry mine plan was developed to extract the ore at a rate of 15 000 tonnes per month and to provide all the safety features, ventilation systems and services of a two shaft mine. In December 1983 a contract was let to Allied Constructions Pty. Limited (Allied) to sink and equip a 4.8m shaft to a depth of 410m and to convert the headframe and winder, which are leased for the life of the mine by PWOL from Allied, from a sinking to a production configuration. Shaft equipment designed by Hardcastle & Richards Pty. Ltd. (H & R) in conjunction with PWOL includes a skip/cage, counter- weight, and an auxiliary cage on rope guides, a sealed ladderway and exhaust air ducts.

Jan 1, 1986