Search Documents

By A. W. CAMERON

Over a 4 hr period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc, and gangue minerals, size by size throughout the whole circuit.Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had some reserve capacity.In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one-third of the lead losses in the final tails.All sizes of zinc values between 100 mesh and 7 microns floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the minus 7 micron fraction.The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971

By Anderson C. G

The design of crawler-mounted conveyor belts installed for the handling of brown coal in open cuts is described.INTRODUCTIONThe State Electricity Commission of Victoria operates two brown coal open cuts at Yallourn, Victoria. The larger of these cuts produces n million tons per year of brown coal containing 67 per cent. moisture, and the smaller, at Yallourn North, produces 1-1 million tons of coal, with a moisture content of 50 per cent. A further open cut at Morwell with projected output of 9-10 million tons per year is in the course of development. In the larger Yallourn open cut coal is excavated by means of conventional bucket chain and bucket wheel dredgers and transport is by electric locomotives and saddle bottom trucks running on 90 cm. gauge railway tracks. At Yallourn North, coal until recently has been largely won by 3i and 5 cu. yd. electric shovels and transported by large diesel-enginedmotor trucks. The difficulty of keeping these trucks in operation during the winter periods owing to the v.ery wet conditions and the high cost of maintenance of these vehicles led to the introduction of a moving face conveyor system.EXISTING CONVEYOR INSTALLATION AT YALLOURN NORTHA conveyor system employing a 36-in. belt running at a speed of 400 ft. per minute and having a nominal capacity of 425 tons per hour with 50-h.p. drive units, was selected as appropriate for the output of the open cut. The conveyor structure adopted was a standard type as used in under...

Jan 1, 1955

Some attempt to minimise the importance of the greenhouse phenomenon. They do so by observing that global temperatures are still within the range of recent variations and that it is still not possible to predict with any certainty what the precise consequences of greenhouse will be. Both observations are true though the conclusion is dangerous. Ice core samples from the Antarctic and Greenland have established the composition of the atmosphere and global temperature over almost the last 200,000 years. The profile of these twin variables shows that they have moved together; when the concentration of CO2 has been up, the temperature has been up and when the former has been down the temperature has also been down. Over almost 200,000 years the CO2 content has ranged between lows of 190 ppm and highs of 270ppm. In just 200 years of industrialisation the CO2 content of the atmosphere has increased to 350 ppm, 50% higher that the mean of the last 200,000 years and 30% higher than at the start of the industrial age. Carbon dioxide is now increasing at 0.5% p.a. Methane, about twenty times more effective than CO2 as a greenhouse gas has doubled in concentration in the last two centuries and is now increasing at about 1.1% p.a. Methane, nitrous oxide, chlorofluorocarbons together with a number of lesser gases will double the greenhouse effect due to in creased CO2 over the next 40-50 years.

Jan 1, 1989

Multiple regression analysis applied to ventilation records of stopes on the Witwatersrand showed that it was possible to estimate the temperature increase per 100 ft for a new stope with a standard deviation of 0' 5°F. The analysis also threw light on the relative effect on this estimate of five different factors.Application of the analysis of variance technique to a factorialexperiment on the production of dust during rock drilling showed that the effects of air and water pressure were quite small but also showed that the between-machine variation was unexpectedly large.Analysis of variance also proved a valuable means for assessing the bias and random error variation of aneroid barometers used in pressure surveys.INTRODUCTIONThree examples are discussed to illustrate the use of the techniques of "analysis of variance" and "multiple regression" in research on the ventilation of gold mines. Although the techniques are basically similar their application to each example has a slightly different emphasis and the examples were chosen for this reason. The variation ofemphasis is as follows.1. Temperature increases in stapes. This work was undertaken as a preliminary to possible extensive controlled experimentation (Lambrechts, 1959). Data collected in routine work by the mine ventilation personnel were used for analysis and no specific experiments were carried out. The main object was to see whether such data could provide any strong pointers to factors which might be worthy ofmore careful study and to factors which could initially be ignored. Of course, there was hope that the study might provide an empirical formula for rough forecasts.

Jan 1, 1962

By P S. R Reddy, V N. Misra

The iron ore deposits in India are rich in iron content but usually contains high alumina and silica. The current industrial practice results three products namely lump, fines and slimes. The lump and fines with or without beneficiation are directly fed to the blast furnace and sintering plant respectively while the super fines or slimes are presently discarded as tailings. Around eight million tonnes of iron ore slimes estimated as being 15 - 20 per cent by weight of run of mine ore containing ~48 - 62 per cent Fe, is discarded every year causing huge loss to the Indian iron ore industry. In addition, these slimes stored in massive tailing ponds pose enormous environmental and ecological problems. Extensive investigations have been carried out on three iron ore slimes generated at Barsua, Bolani and Meghahatuburu iron ore mines of India. The studies include physical, chemical, mineralogical characterisation and beneficiation studies adopting conventional hydroclyclone and wet high intensity magnetic separator. The characterisation studies have indicated that most of the gangue minerals are accumulated in finer fractions. The studies on hydrocyclone and magnetic separation had indicated that an iron concentrate of 61 - 65 per cent Fe could be obtained by recovering 59 - 78 per cent of the iron values present in the slimes. Depending on the nature of the slimes the alumina and silica levels have been brought down to 2.5 and 1.0 per cent respectively. The effects of different operating and design variables along with detailed characterisation studies have been highlighted.

Jan 1, 2002

By Jianmin H, Shuqin L

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed.The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by i. Dr & Prof. Beijing Graduate School, China University of Mining Science and Technology,Beijing,China 2 Northern .Jiaotong University, Beijing,China 3. Beijing Graduate School, China University of Mining, Science and Technology

Jan 1, 1992

By Edwards A. B

The occurrence of gold so finely divided as to be invisible under the microscope, even at magnificatioIl; of 1,200 to 2,000 diameters, is rare, but not unknow;n.. Burg (1930) has described an occurrence of such "invisible gold" from the 25/37 vein of the Bradisor mine at Brad in the Siebengeburgen district of Rumania (Transylvania), in which the pyrite contained up to 150 grams of gold per ton (approx. 5 oz. gold per ton). Hoffman (1931) has described an epithermal silver gold ore from the Titiribi district of Columbia (South America), in which "invisible gold" to the extent of 150 grams per ton occurred in the pyrite, arsenopyrite and zincblende; and Haycock (1937) has recorded it in pyrite from the Surf Point mine (Canada), which contained no visible gold, but yielded positive testsfor gold whenever samples drilled from polished surfaces of apparently homogeneous pyrite were tested spectrographically.The examination of a cyanided pyritic concentrate, together with a sample of the ore from which it' was prepared, from the Dolphin East lode at Vatukoula, Fiji, carried out as part of the programme of the Mineragraphic Section of the Council for Scientific and Industrial Research, Australia, has established a further occurrence of "invisible gold" in pyrite and arsenopyrite. The Dolphin pyrite contains about 25 oz. gold per ton, and the arsenopyrite contains more than 33 oz. per ton.The concentrate has been prepared for the Mill Superintendent of the Emperor Gold Mining Co. by L. Mayger...

Jan 1, 1946

By S Cossfo Torres

Minera PenmontÆs gold mine, La Herradura, is located at the northwestern Mexican state of Sonora and consists of an open pit mine and heap leaching facility for the recovery of gold. The production began in July 1998, and today La Herradura produces about 200 000 oz of gold per year. Standard sampling and assaying protocols were established during exploration based on heterogeneity tests. However, at deeper zones of the pit, coarse gold became evident and it was necessary to develop a new sampling protocol in order to minimise the fundamental error and improve the metallurgical accounting. This new sampling protocol requires cyanide leaching the whole pulverised sample from the blasthole, assaying pregnant solution and fire assaying 50 g of tailings. A sampling study was performed on 195 blasthole samples analysing gold under the standard and new protocols. The new protocol demonstrated that the original one underestimated gold grade by approximately 27 per cent, with impacts on ore misclassification and metallurgical accounting. According to the ore grade control system, mineral with gold grade above 0.35 g/t was sent to the leach pad and mineral with lower grade was classified as waste. Based on the sampling study, it was decided to classify a low-grade ore with gold assay between 0.20 and 0.35 g/t which was stored for future treatment under better gold prices or should mine production decrease. These two conditions were present during 2005 and 2006, when about 3.5 Mt of low-grade ore were leached.

Jan 1, 2008

Titanium tetrachloride may be reduced to trichloride with hydrogen on a hot tungsten filament and other hot: surfaces. The effect of temperature, time and size of t.he filament on the rate of reaction has been studied. A laboratory unit for preparing a few pounds of trichloride at a time is described. The yield of trichloride is 2·2 - 2·4 gm/sq. cm. of hot surface/hour at 1,000°C. and the energy requirement 3'5-4 kWh/pound of trichloride produced.'INTRODUCTIONThe lower chlorides of titanium (titanium tri- and dichlorides) are amenable to electrolysis, being electrovalent in nature. Furthermore, relative to other oxygen-free titanium salts, they are easy to prepare in a pure state and their use has been investigated to prepare titanium. The experimentaJ work described in this paper deals with the preparation of titanium trichloride by reduction of titanium tetrachloride with hydrogen on hot surfaces.REDUCING AGENTS FOR TITANIUM TETRACHLORIDEThe free energy diagram (Fig. 1) for the formation of chlorides suggests that titanium' tetrachloride may be reduced to trichloride by various reducing agents such as aluminium, zinc, arsenic, antimony, tin, mercury, silver, hydrogen, sodium, potassium and magnesium. Ruff and Neumann (1923), Thorpe (1885) , Billy and Brasseur (1935) and Seurbert and Schmidt (1892) used various metals to reduce tetrachloride to trichloride and found that the yields were invariably low and the products difficult to separate.Besides the metallic reducing agents, hydrogen may also be used to reduce titanium tetrachloride to trichloride.Goerges and Stahler (1909) obtained a deposit of violet...

Jan 1, 1956

By M Freeman

Significant improvements in the metallurgical performance at Pasminco Rosebery Mine have occurred over the last two years. Lead and silver recoveries have increased by more than ten per cent, lead concentrate grades are four per cent higher, zinc recoveries are up 1.5 per cent, and zinc concentrate grades have increased by two per cent. These impressive results have not occurred through the application of some new wonder reagent, but through the application of some fundamental metallurgical principals. The basic premise applied during this study was that to make an effective separation you must first achieve liberation. Therefore, the laboratory and plant studies examined the liberation characteristics within the lead circuit, and the impact of regrinding. The work demonstrated clearly that galena/sphalerite liberation was poor, and significantly impaired plant performance. Further, it was suggested that the application of lead regrinding of the lead scavenger concentrate and the lead first cleaner tailing would not only benefit lead metallurgy, but also improve sphalerite flotation. A similar approach was then applied to the zinc circuit. From these studies, solutions applying simple circuit changes utilising existing equipment were proposed and implemented. Further to the improvements in galena/sphalerite liberation, significant improvements in concentrate quality were achieved by reducing variation within the process. The implementation of changes in work practices negotiated in the Enterprise Agreement, employee contributions and specialist training also made a significant contribution to the unprecedented improvement in the lead and zinc flotation circuit performance. The results of these plant changes are discussed, along with the suggested scope for further improvement.

Jan 1, 2000

By A He, J Li, J Pan, J Clout

The removal of sulfur from SO2 containing flue gas is improved by adsorbing SO2 into solution with manganese ions as catalyser, however, burnt lime slurry has to be added to modify solution pH and the CaSO3 by-product is of low economic value. In this paper a novel one step process for simultaneous manganese leaching-desulfurisation of flue gas is presented. An investigation of the effect of process parameters included flow rate and SO2 concentration in flue gas, adsorbing time, solution to solid mass ratio, leaching time, and their impact on the oxidation and removal of SO2 from flue gas. The catalysing mechanism of manganese ions on the oxidation and SO2 removal was demonstrated by calculation of the species originating from manganese ions and SO2 in the solution according to solution chemistry. SO2 removal in the adsorbing solution took place at pH 5 - 6, where manganese ions dominantly occurred as Mn2+, and the chain reactions for oxidation of SO2 starting from HSO3- were improved by the presence of Mn2+. SO2 bearing flue gas was effectively desulfurised by leaching rhodochrosite (MnCO3), with desulfurisation of the flue gas and modifying the solution pH being achieved simultaneously, and MnSO4 of high economic value recovered from the leachate. 85 per cent manganese leaching and over 70 per cent desulfurisation of the SO2-bearing flue gas were achieved with only one adsorption stage under optimum conditions.

Jan 1, 2004

This paper describes the oil engihe plant owned and operated by Gold Mines .of Kalgoorlie Limited, and gives some details of installation, operational, and maintenance experiences which have arisen during the years of service, the last 5 years of which have been under the writer's control. Nos. 1, 2, 3 and 4 alternator units have run 50,276, 48,006, 49,677 and 25,930 hours respectively, and much knowledge has been obtained of their performances and faults. During the war years, it has not been easy to obtain spare parts; this, coupled with the loss of No. 4: alternator unit to the Commonwealth Government, made operation and maintenance a very difficult problem.All engines are of the enclosed vertical, single acting, 4-stroke cycle, airless injection type.The electrical power plant originally consisted of four 6-cylinder Belliss & Morcom heavy oil engines, direct coupled to Bruce Peebles alternators, running at 375 r.p.m., and generating 3-phase electric power at 3,300 volts, 50 cycles.No. 1 unit, installed in 1936, is a 6-cylinder 450 b.h.p. standard 12A Belliss & Morcom heavy oil engine, direct coupled to 280 kw. 0.8 p.f. alternator. The remaining three units are 6-cylinder, 660 b.h.p., lSA oil cooled piston type Belliss & Morcom heavy oil engines, direct coupled to 410 kw. 0.8 p.f. alternators, making a total capacity of 1,510 kw.No. 4"alternator. unit, an 18A Bellis.& Morcom set, was taken over by the Commonwealth Government in June 1943.

Jan 1, 1945

A statistical investigation of folding at Mount Isa disclosed similar patterns in both the shales and the "silica dolomite" zones. Analysis of these patterns yields 3 groups of folds fully developed north plunging folds, fully developed south plunging folds, and flexuresrepresenting stages of development of folds. Interpretation of results indicates that a regional force from a southerly direction was responsible for the folding.The general pattern of shearing is allied to that of folding, with the exception of bedding-plane shearing. Many shears resulted from continued application of force on folds which ruptured after overthrusting. Other shears resulted from rupture of the more incompetent shale members, without associated folding. The shear pattern is consistent with the theory of a regional force from a southerly direction.INTRODUCTIONThe notes on folding and shearing presented in this paper are part of a current study of the structural geology of Mount Isa.FOLDING 1Measurement of FoldsInvestigation of folding underground involved the measurement of plunge, strike and dip of the axial plane, and the order of magnitude of each fold, together with its location and the rock type. The total number of folds measured was 701, of which 411 occurred in shale areas and 290 within the "silica dolomite" zones. All folds measured are located on main levels, from 7 level to 13 level inclusive. The sections of the mine involved are the Black Star, Black Rock and Racecourse. Detailed investigation of folds on the upper levels (4, 5 and 6) has not yet been done, but observations there suggest...

Jan 1, 1961

By Frazer E. J, Lwin T

Measurements of coulombic efficiency (QE) for zinc electrodeposition were carried out under mass-transfer-controlled conditions using a rotating disc electrode in synthetic acidic zinc sulphate solutions. Various methods of solution preparation and purifi- cation were investigated using reagents vary- ing from analytical grade to high purity; the purest solution was obtained-by dissolving 99.9999% zinc (Koch-Light) in sulphuric acid solution (BDH Aristar). Improvements in sol- ution purity did not necessarily increase QE, especially where apparently beneficial impur- ities (e.g., Pb) were initially present. The maximum QE obtainable through variation of temperature (T), current density-(i) and elec- trode rotation rate was established using a statistical optimization technique. The QE was determined principally by T and i, with significant interaction between these factors in the highest purity solution. QE contours, which gave an overall view of solution per- formance, were constructed and predictions about the response under conditions similar to plant practice were made. Wark's Rule (the dependence of QE on zinc/acid ratio) was obeyed in the purest solution over the range of composition commonly encountered in zinc plants. High concentrations of Na2SO4 and K2SO4, which occur in some plant solutions, were found to increase QE marginally ("1.2%). The intrinsic effects of individual impurities such as Cu and Ni were evaluated by additions (up to 5 ppm) to the purest solution. Decreases in QE were found to be minimal at the impurity levels normally encountered in zinc plants.

Jan 1, 1987

By Smith J. W, Hart G. N

Compositional and isotopic analyses of coal seam gases in the Southern Coalfields have shown that these gases frequently contain abnormally high concentrations of magmatically derived carbon dioxide. The size of this carbon dioxide reservoir and the extent of permeation of the sediments by carbon dioxide are not known.Therefore caution in evaluating the natural gas potential of the region is advised.

Jan 1, 1981

I've talked a number of times in the past year or so to audiences like today's about culture -about thinking of it, understanding it, respecting it. So, rather than talk just yet about your laws for mining on Aboriginal land and the successes some of us and some of you have been able to achieve, I'd like to first of all talk about cul- ture as I understand it. Anyone who proposes any kind of development on Aborigi- nal land needs to have some basic understanding of what we, the traditional owners of that land, are about. Without that under- standing, you will find difficulty in coming to terms with us. Many people have experienced this difficulty and, unless we can do something about it together, many more will continue to find it.

Jan 1, 1988

With the advent of the mini computer and the relational database project management has experienced a new lease of life. The project manager no longer has to wait days for his reports, and he doesn't have to thumb through a foot of four part stationery to find that one line of information. The new techniques bring characteristics that are music to the ear of the project team giving them a better chance of bringing the projects in on time and within budget.

Jan 1, 1983

The refractory industry in New Zealand is small, consisting of two main manufacturers - one at Huntly and the other at Kamo. Together these would have an annual refractory production of about 30 000 tonnes. The industries which use refractories include two steelworks, NewZealand Steel Limited and Pacific Steel Limited, the former is involved in continuous casting from sponge, iron and scrap steel and the latter is involved in ingot teaming from scrap steel and steel billets; One aluminium smelter, cement works, dairy companies, small foundries producing engineering requirements and many other small users. The New Zealand manufacturers produce refractories in thefire brick range, that is up to 50 per cent alumina content (ignited basis), based on indigenous raw materials and in the high alumina range up to 85 per cent alumina content (ignited basis) based on imported bauxites. All of the basic refractories high purity silica and high alumina low alkali refractories and many of the higher grade acid resisting refractories are imported.

Jan 1, 1976

Financial markets are subject to constant change and project finance, as a product within these markets, adapts and will continue to adapt with those changes. A meaningful discussion of these adaptations requires an understanding of differences between non-, limited and full recourse project finance. The reasons sponsors seek and lenders provide project finance are also pertinent in this context. Arranging a project, financing package can be a canplex and time consuming task. An important first step is choosing the right advisor for the assignment and then structuring and tailoring the financing before approaching prospective lenders. The last thirty years has seen changes in the needs of sponsors and the ability of lenders to meet them. These shifts in preference may well be a guide to the future. Several major project financings successfully canpleted in Australia in the last few years and more recent examples are broadly discussed. Project finance will be keenly sought in the future and the form and nature it takes will continue to vary.

Jan 1, 1983

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986