Search Documents

The grade (or value) to volume relationship which constitutes a target orebody is used to show that the concentration of diamonds in an economic deposit may be as low as O.Olg/t. Diamond valuations from an Indonesian deposit demonstrate that the largest 5% of the diamonds in the deposit contributed 25% of the mass of diamonds recovered and 70% of the value from the ore. The need to consider the large stone content and the probability of recovery is used to estimate that the sampling density is required to be as high as 4-10,000ppm for a VLC deposit. This is compared with an acceptable sampling density for a bauxite deposit of 700ppb. A case history of the discovery of a diamond bearing paleo-channel in the Ellendale field in Western Australia illustrates that the sampling task becomes impractical. It requires an excavation in excess of 300,000 bcm of material to prove a 5M hem ore reserve. The conclusion is reached that setting up a small scale mining operation is an appropriate method of proving such an ore reserve and that the Code of Reporting should allow a category of "Mineable Resource" to cover such a situation.

Jan 1, 1990

By A N. Parry, G van Wyk

"Sensor based automatic ore sorting technologies are used in the minerals industries to efficiently remove waste and submarginal grade material from crushed and screened run-of-mine (ROM) ore, producing a coarse (typically >10 mm) upgraded preconcentrate at an early stage in the mineral processing circuit. This avoids additional energy intensive downstream processing of this rejected component of the ROM feed, leading to lower unit operating costs and reduced tailings disposal volumes.Test work on bulk low-grade gold ore stockpile samples from Central Norseman Gold Proprietary Limited has been conducted, indicating high gold recoveries as well as high material rejection rates. A financial model, based on these results, evaluates grade sensitivity and identifies a minimum stockpile grade for adequate financial returns. The base case modelling estimates that the ex-stockpile grade (including the fines bypassed fraction) can be more than doubled through ore sorting and that the project will be highly viable with strong cash flow generation at stockpile grades as low as 0.7 g/t gold. The modelling will enable the company to benchmark ore sorting options against stockpile reclaim and screening operations currently employed. Citation:Parry, A N and van Wyk, G, 2016. Upgrading Low-grade Gold Ore Stockpiles by Preconcentration Using Ore Sorting - an Assessment of the Economic Impact and Viability, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 179–190 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Flue gases from electrical power station boilers, roasting, metallurgical and chemical plants could be treated by flotation using conventional flotation machines. The flue gases are introduced into the pulp instead of the air. The flotation media is a suspension of Ca(OH)2 or CaCO3 or a solution of NH4OH etc containing Na oleate as collector and frother. The SO2 and dust content of the initial flue gases were experimentally reduced by 100 to 1000 times in one flotation operation. The velocity of the flue gases through flotation machines could reach approximatively 0.4 to 0.5 m/s and more against 1.5 m/s reached in scrubber absorbers used for this purpose, but the quality of purification is expected to be better for flotation, which is essential for the cases of heavy polluted metallurgical and chemical flue gases. For some chemical plants the flue gases flotation media may be different and more suitable as compared to the above mentioned media. The proposed flotation method could be used for separation of dry grinded ores in the form of aerosols, with a realisation of flotation from a closed space (gas bubble in the pulp) onto the interface liquid-air where the particles are attached inside the bubbles.

Jan 1, 1993

Cyanidation tests by bottle agitation were conducted on an oxidized lead-silver ore containing approximately 12% Pb and 500 g/t Ag. Over 60% of the silver was leached when the ore was ground to 100% passing 0.15mm, whereas 50-60% of the silver was leached when the ore was only ground to 100% passing 0.5mm. Slurry handling and dewatering at the fine grind size were very difficult due to the high clay content of the ore, however this problem was greatly reduced at the coar- ser grind size. The silver recovery at the fine grind size was very dependent on cyanide solution strength with stronger cyanide sol- utions (containing more than 0.1% NaCN) re- sulting in lower solution silver contents. This was thought to be due to the precipi- tation of leached silver by zinc, which was also leached from the ore by the higher cyanide levels. There was a critical zinc level in solution of approximately 1000ppm, above which the silver recovery fell markedly. Cyanide and lime consumptions for this ore were high (typically 5 kg/t and 40 kg/t respectively), hence the processing of this particular ore by cyanide leaching is un- economic at current silver prices.

Jan 1, 1987

By S Brunt

A new elution process has been developed for the recovery of gold thiosulfate from ion exchange resins. This is a synergistic system which utilises a base eluent, such as nitrate or trithionate, along with an additive that improves the elution of gold. The use of the additive enables lower eluent concentrations to be adopted, as well as weaker eluents such as chloride. With the chloride + additive system, complete gold elution can be achieved within 12 BV when utilising an eluent flow of 5 BV/h. When the eluent flow is reduced to 2 BV/h, complete elution is achieved within 8 BV. Similar results are obtained when using nitrate or trithionate as the base eluent. A copper pre-elution process has also been developed, whereby the majority of copper can be stripped within 5 BV prior to gold elution. This method is a significant improvement on the ammonia + oxygen pre-elution previously suggested. The development of a new analytical procedure based on ion chromatography with UV detection is also described for the quantification of polythionates in leach solutions and loaded on resins. This enables analysis to be carried out for resin-in- leach type processes where the polythionates are being formed in solution and simultaneously adsorbed onto the resin.

Jan 1, 2007

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

By P Corbett, P Sheffield

Centennial Coal operates the Springvale longwall mining operation which extracts coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale, and the neighbouring Angus Place mine, have a history of difficult geotechnical conditions where combinations of a relatively high stress regime and weak, laminated roof and extensive geological faulting has led to numerous roof failures throughout the mine’s life. Following development, the mines underground roadways can experience high levels of roof movement which may lead to roof falls. Multipoint wire extensometers are extensively used throughout the mine for roadway condition monitoring, and to reactively drive remedial strata support through trigger action response plans (TARPs).As a result of the use of high-density extensometer monitoring over a long period, the mines have an extensive archive of legacy data. Data processing has evolved over time in order to accommodate the increasing data volume, including direct data entry from the recently introduced hard-wired real-time monitoring instruments. It is likely that telemetric real-time instruments will be introduced in the future, which will cause another step change in data management requirements. This paper discusses the transition to and evolution of relational database management systems for extensometer and associated data.This paper also presents case studies of the use of a new software tool for reprocessing legacy data to enable time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. The software can be used proactively in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological and geotechnical data to allow correlation of monitoring data results with risk factors.CITATION:Corbett, P and Sheffield, P, 2015. The use of high-intensity monitoring data to better characterise geotechnical properties of a non-homogeneous rock mass, in Proceedings Third International Future Mining Conference, pp 145–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T Baumgartl, D Bradshaw, B Forsyth, M Edraki

In a tailings storage facility, the chemistry of pore water is a function of oxidation and dissolution of sulfide minerals, containing metals and metalloids, the neutralising effect of gangue minerals and the geochemical processes controlling solute equilibria such as pH, redox potential, precipitation, ion exchange and adsorption. On the other hand, the changes in geochemical composition of tailings feed over time is a function of spatial variability within the orebody and modifications in processing method. Tailings properties such as pyrite content, pH, concentration of deleterious elements, surface chemistry, pore water chemistry and particle size are already shaped in the dynamic environment of a process plant.To engineer desired environmental outcomes, a new research framework is needed. The new approach should follow the physical and geochemical processes of tailings feed and construct models that can be used for the prediction of seepage water quality and dust propagation and evaluate the potential re-processing of tailings or production of tailings with desirable surface chemistry, particle size and internal structure. The challenge of developing tailings engineering model is not in laboratory techniques, but more of the overall communication of results and establishing the link between disciplines. It requires investigating geochemistry across mining and processing for improved environmental outcomes at tailings storage facilities.The paper reviews the current tailings management practices by comparing the geochemistry and mineralogy of tailings and the chemistry of seepage water from three Australian case studies in the context of geology, mineral processing and climate. Some alternative methods of tailings management are also reviewed and it is concluded that a proactive multi-disciplinary approach is needed with respect to tailings management, based on a novel integrated research framework.CITATION:Edraki, M, Forsyth, B, Baumgartl, T and Bradshaw, D, 2012. Geochemistry of tailings and seepage from three tailings storage facilities in Australia - Uncapped, capped and active tailings, in Proceedings Life-of-Mine 2012 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By N Murthy

Alumina is a major impurity in Australian iron ores and as the higher grade ores become depleted there will be a stronger focus on treating lower grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the alumina content. High alumina in iron ore is deleterious in that it can:• produce slags with lower desulfurising capacity,• reduce sinter/pellet strength and quality, and• produce higher slag volume and increase slag viscosity.Meeting iron ore quality specifications for alumina by blending ore from different sources will eventually be insufficient. Hence, innovative flow sheets based on new and commercially available technologies will be required. Their advantages and disadvantages, the testing methodologies and the challenges and diffi culties involved in reducing the alumina content of iron ores are presented and discussed.

Jul 11, 2011

The Cadia Valley Operations currently hosts a large operational open pit, a large operational sublevel caving underground mine and two other underground projects at the study stage. This scenario creates an unusual situation for the evaluation and planning of a fifth major open pit project. The Cadia East Open Pit is a large gold-copper development located adjacent to the operational open pit and above one of the underground projects. A study team is conducting a comprehensive and robust analysis of the target orebody. Two key factors for this project include the existing and planned projects within the valley and the wide range of available mining methods. The aim for the study team is to present an optimal and practical case which suits the entire Cadia Valley Operation. A rigorous and robust analysis of the situation requires that each factor be properly evaluated. A modular system has been developed which allows the wide range of scenarios to be quickly and meaningfully considered. Sensitivities for each module drive the further development of that particular module. As each scenario progresses, an assessment is made evaluating its value, strategic value and practicality. In such a way, the number of scenarios is gradually reduced at each stage to produce a final short list of feasible cases. Each scenario on the shortlist is then assessed with regard to the existing operations and other projects. A qualitative and quantitative analysis is made. This ranking is used to provide the recommended case.

Jan 1, 2007

By M Norbert, C Bennett

The Legacy Way Tunnel was constructed from Toowong to Kelvin Grove in Brisbane, and is the first large-scale underground excavation in the Bunya Phyllite in Brisbane. The Legacy Way Tunnel is 4.3 km in length, comprising two mainline tunnels excavated by a tunnel boring machine (TBM) with 46 connecting passages excavated between the mainline tunnels for egress provision and services. The Legacy Way Tunnel passes through two geological formations, the Bunya Phyllite and the Neranleigh Fernvale Beds. The Bunya Phyllite is the dominant formation of the Legacy Way Tunnel, extending for three quarters of the tunnel prior to intersecting the Normanby Fault Zone (NFZ) and the Neranleigh Fernvale Beds. The NFZ forms the contact between the two formations as part of the Brisbane Metamorphics, which underlies the majority of Brisbane City. The development of the geological model and the understanding of the ground’s reaction to tunnelling was an iterative process. The tender phase investigation data has been supplemented with additional design phase investigation boreholes, geophysics and walk overs. Aerial photograph interpretation coupled with borehole data allowed the development of the domains along the length of the tunnel. Early excavations for the spoil conveyor tunnel and borehole data from subsurface instrumentation installation provided the first construction phase data followed by the commencement of tunnel boring machine (TBM) excavation. Routine cutterhead inspections coupled with ongoing reviews of the predicted geology resulted in clear response triggers to selection of segment types while detailed inspections in passage locations provide the initial classifications for segment removals.CITATION:Bennett, C and Norbert, M, 2014. Tunnelling within the Bunya Phyllite of Legacy Way, Brisbane, Queensland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

Waihi Gold Mining Company Limited, a wholly owned subsidiary of Normandy Mining Limited, operates the Martha gold mine, located in the township of Waihi, New Zealand. The operation, an unincorporated joint venture, comprises Normandy Mining Limited (67.070/0) and Otter Gold Mines (32.94%). Since gold was first discovered at Waihi in 1878, it has formed a key part of the region's economy. In 1909 the Waihi mine was described in a report to Parliament as æthe most important gold mine in Australasia and one of the greatest in the world.Æ That was a record year for production, with 416,813 tons of ore mined and some 1,120 men employed. Today the mine produces up to 1,250,000 tonnes of ore annually, and the project employs some 234 men and women. In 1999 the value of the gold and silver produced ($59 million) made up 47% of Waihi's estimated GDP. Waihi Gold has made significant contributions to the Waihi economy, community and the Hauraki region as a whole. Since the mine was re-opened in 1987, thousands of local people have benefited from the mine. In 1999, consents were granted allowing an extension to the mine life (the Extended Project) and this will result in a further seven years of economic benefits resulting from mining activity. The Company has undertaken extensive consultation throughout project planning, construction, operations and rehabilitation. Ongoing liaison and involvement with all community sectors, including Tangata Whenua and Iwi, local residents, recreational groups and schools remains an integral part of the operation. Throughout the life of the modern Martha Mine, the Company has actively supported the local community in the form of donations, sponsorships, the provision of amenities, and by participating in community events. A well established environmental team exists at the site. Environmental and community performance is measured by an independent five-assessment process, and the Company is committed to achieving excellence through ongoing improvement programmes and staff awareness. When the mine is closed, the open pit area will be transformed into a recreational lake, and the tailings storage facilities will be rehabilitated to become a combination of wetlands, grassed areas and ponds. Resources will be provided by the Mine to ensure the rehabilitated site remains in a safe and self-sustaining, stable condition in perpetuity. The mine is regarded as a showcase on a world standard of how a modem mining operation can successfully coexist with the nearby community.

Jan 1, 2000

By S C. Bhowmik, R Gupta

This paper presents the ventilation problem faced by Jaduguda uranium mine, operated up to a depth of 905 m. The first two stages of the mine workings are up to 555 m, which are nearly exhausted. The third stage of the mine is from 555 m to 905 m and presently most of the stopping and development activities of the mine are carried out in the third stage. The total available intake quantity in the third stage was only 21 m3/s. As a result, the mine was facing a radiation hazard. The different instruments and the methods used for monitoring of radiation levels are also presented in the paper. It was observed that the average individual effective dose (external + internal) of radiation workers in Jaduguda mine increased from 6.93 mSv/y in 1995 to 9.5 mSv/y in 2001 and during this period the average individual effective dose of mine workers of the world was less than 5 mSv/y. Keeping this problem in view, a detailed ventilation investigation has been carried out in this mine. Initially the requirements of intake air quantity have been assessed by carrying out field investigation in different stopes and it was found that the third stage workings require nearly 100 m3/s. A detailed ventilation survey has been carried out in the total ventilation network and a basic ventilation model of the mine has been prepared. Different alternative schemes for effectively ventilating the third stage workings of the mine were simulated and a set of recommendations were made for implementation. The recommendations were partially implemented in 2002. As a result the total intake quantity to third stage workings increased to nearly 70 m3/s and the average individual effective dose (internal + external) of mine workers came down from 9.5 mSv/y in 2001 to 6.65 mSv/y and 6.60 mSv/y in 2002 and 2003 respectively. The implementation of remaining recommendations is in progress. Finally, a mathematical model has been formulated from the first principle for predicting air quantity requirements in cut and fill stopes in uranium mines and this model is being validated for further use.

Jan 1, 2005

THE following notes simply sum up the writer's experience, which extended over a very busy period of some three years, dealing with wolfram ores and concentrates. The three methods for the estimation of tungsten that are discussed below are well known, but these results of their trials and comparison under technical conditions may be interesting. Method I. The routine procedure for the assay of rich wolfram ores or concentrates was as follows: Take 1 gram of finely-ground sample; digest with HCl and HNOs for about 2 hours, evaporating down to near dryness. To the remaining 5 cc., say, of liquid, add water, warm or boil for 1 to 1.5 hour, filter through a small filter paper, and wash the beaker and the insoluble matter with hot dilute HCl. It is best to keep the bulk of the insoluble matter (WOs, Si02, etc.) in the beaker at this stage. Then plaee a weighed porcelain dish under the filter funnel and wash the beaker and the filter paper with successive small quantities of strong NHOH, finally bringing all the insoluble matter on to the filter paper, and collecting the ammoniacal filtrates in the porcelain dish (S). Then place the filter paper with the insoluble matter in a porcelain crucible, dry and burn off the paper, cool, and brush the contents of the crucible on to an agate mortar, grind it to flour, and brush this back to the original beaker without loss. In the absence of draughts this can be done safely. Re-treat this residue with' acid and ammonia as above, running the second ammoniacal filtrate into the previous porcelain dish, which in the meantime has been heating on a water-bath.Finally evaporate to dryness on the water-bath the combined ammoniaeal filtrate, and then heat gradually to a red heat over a Bunsen burner, cool, and weigh. Then the contents of the porcelain dish give the WOs (tungstie aeid) direcvly (5).The final filter paper and insoluble matter may be ignited in a porcelain crucible, thus giving the "insoluble matter." If the ore...

Jan 1, 1922

By H von Blottnitz, J L. Broadhurst

Eco-efficiency has been proposed by the World Business Council on Sustainable Development as an environmental performance indicator framework that contributes to sustainability by assisting corporate decision makers improve the environmental performance of their operations and processes, while also extracting additional economic value. Given that the recent engagement of the minerals industry with sustainability has highlighted the need for requisite tools and methodologies, it is therefore of interest to assess whether eco-efficiency indicators can drive sustainability performance improvement during process design within the minerals industry. Previous work indicates that the choice of sustainability performance indicators to be used for decision making needs to be governed by the decision context; ie the performance indicators need to be fit-for-purpose. Here, the strengths and weaknesses of eco-efficiency indicators are analysed using case studies. First, a more rigorous definition of eco-efficiency indicators for the minerals industry is proposed based on indicators currently offered in the literature. Two case studies are then selected to reflect typical decision situations encountered within minerals process design. For each case study, eco-efficiency indicators are computed and are compared to more traditional graphical representations of the economic and environmental performance of process design alternatives considered. The sensitivity of these indicators to various process design parameters is also investigated. Results confirm that the meaningful application of eco-efficiency indicators is strongly dependent on the decision context in which the process data is generated. Results also show that eco-efficiency indicators can be related to technical process design parameters to allow for richer communication of performance information for various decision trade-offs; however, in some cases, graphical approaches that provide more insights into the environmental-financial trade-offs should be preferred. The research thus contributes to guiding the selection of the appropriate tools for more environmentally sustainable design of minerals beneficiation processes.

Jan 1, 2009

By J Balzary, A Mohais

Dynamic market and operating conditions, coupled with an environment in which multiple objectives and trade-offs are common, pose major challenges for planners and schedulers working in any mining entity. Many mining companies recognise the need to shift from a siloed mining-focused push model to an integrated value chain, demand-driven approach, but there are still fundamental barriers in business process and the supporting technology preventing a consideration of end-to-end optimality.This paper presents some elements of experiences working with companies to adopt such advanced approaches. In addition to algorithmic elements, an approach to phased and gradual deployment of progressively more sophisticated optimisation models is described. From a practical software adoption perspective, it is believed that this last concern is also of primary importance. Next generation approaches to the optimisation of complex bulk commodity demand chains, namely iron ore and coal are presented, with case studies in the world’s largest integrated operations in Western Australia and Queensland from the raw material mined through to market. Utilising accurate simulation models supported by metaheuristic optimisation techniques, a range of ways to engineer a dynamic decision support framework that can adapt and change with the inevitable changes in commodity markets is explored. Objectives such as total revenue, margin, cost, NPV, throughput, asset utilisation, contractual penalties and bonuses, and energy consumption can be managed simultaneously across the mine, plant, logistics network, port operation, shipping and sales domains.CITATION:Balzary, J and Mohais, A, 2014. Consideration for multiobjective metaheuristic optimisation of large iron ore and coal supply chains, from resource to market, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 213–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Santana, V Ferraz, G Pinto, G Cruzado

Morro Agudo is an underground zinc and lead mine owned by Nexa Resources. The mine uses room and pillar as the main mining method. The recovery of pillars as well as the opening of new excavations using sublevel stoping as mining method has been studied. On some occasions, the need to recover pillars and open a stope by using the sublevel method happens in a region that is already excavated or in deeper areas than those mined so far. These changes represent a major geotechnical challenge due to the complex openings of the mine and interaction between two different mining methods. Historically, geotechnical mapping, kinematic analysis and a 2D numerical model were used to evaluate the new mine openings, and in 2021, 3D numerical model was introduced, which enabled global and local assessment of new excavations impact and the stability of openings after recoveries. The 3D model, made with MAP3D, is used to evaluate each pillar to be recovered, considering the spans of the resulting openings, the ideal sequencing of removal to maintain stability, in addition to the impact and geometry of the pillars left in the chambers. Pillar recoveries done in 2021 and the impact of it on the pillars left were the sources of the back analysis to calibrate parameters inputted on numerical model to assess recovery on new chambers and Phyllite has been considered into the model and it has been a source of instability due to its parallel position to roof of room and pillars and stope hanging walls.

Nov 29, 2022

By P Card

“Let’s get discipline and quality into easy to understand evaluations!” Project Managers and MetPlant Operators accept poor quality evaluations because they are generally unaware of what they should expect.The 2010 draft AusIMM ‘Guidelines for Techno-Economic Evaluations’ were collated by a subcommittee of practitioners and are regarded as best practice.They apply directly to projects and metallurgical plant evaluations, including those with a heavy technical basis. They can be applied to technical problem solving where there are no monetary computations. Project Managers and MetPlant Operators should demand that economic models and evaluations follow the six principles. They should become working tools which are easy to understand, fit for purpose, consistent, rigorous, record sources of input data, have key graphs and are rapid to audit.

Aug 8, 2011

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022