Search Documents

By Hayes P. C

In commercial mineral processing operations it has been found that the conditions in the drier have a considerable effect on the subsequent electrostatic separation of nttile and zircon. Laboratory scale studies simulating these heat treatment processes have shown that the electrical conductivity of nitile varies markedly with treatment temperature, time and gas composition. The zircon on the other hand is unaffected. By increasing the electrical conductivity of the rutile, significant increases in separation efficiency can be achieved. Electron microscope investigations have shown the increase in electrical conductivity to be associated with the production of planar defects in the crystal lattice.

Jan 1, 1991

By Mosusu N

Geothermal anomalies of different types occur within distinct geological/structural settings in Papua New Guinea. According to R.F. Herring, geothermal occurrences in Papua New Guinea can be classified into two types, those related to vulcanism (Lihir, Rabaul and other series of islands along the volcanic arc) and those resulting from a regional heat flow probably caused by radiogenic sources, for instance those in the Wau/Bulolo area. The manifestation of this potential source of energy generally coincides with either converging or diverging tectonic plate boundaries. Previous inventories on thermal waters were carried out by vulcanologists from the Rabaul Observatory in the early 1960s. However, these studies rarely included chemical analyses of water and gas emissions and the investigations were carried out in an ad hoc manner, generally as a secondary activity. The most recent investigation on thermal waters was conducted on Lihir Island in connection with the development of the open pit gold mine. These studies included detailed exploratory drilling to a maximum depth of 730 m, and a water chemistry isotopic sampling and analysis programme. The hydrothermal waters were not considered as an energy source but as a hazard during the development stage of the mine. Nevertheless, the geothermal anomaly observed at Lihir includes hot springs emerging along the coastal zones with temperatures that approach 100¦C, steam, and thermal borehole waters with temperatures that exceed 200¦C. Chemical analysis results of thermal fluids from Rabaul, Talasea and other areas in Papua New Guinea generally show high total dissolved solids and low pH. In contrast, recent results from the deepest and hottest thermal source at Lihir shows a neutral pH, a Na-CI-SO4 composition and temperatures above 200¦C. Despite the concentration of chloride being similar to that of sea water, other chemical results and stable hydrogen and oxygen isotopic compositions of thermal fluids imply the source to be mixture of local meteoric water and deep thermal water rather than sea water. Results of geothermal modelling suggests that the total geothermal uptlow is equivalent to 54 MW.

Jan 1, 1997

By Moffatt G

Approval to operate Longwall No. 7 at Appin Colliery in 1979 was granted pursuant not only to the usual statutory provisions, but also that an adequate means of drainage of methane gas be incorporated. A methane drainage plant was subsequently designed and constructed some two km from the pit top at the site of the Colliery main upcast and down cast shafts. Modern plants of this nature are completely automated using programmable controllers and computers to provide control and management reporting functions. Complex mechanical systems are installed to extract the gas and in handling and storage processes. Gas utilisation plants exist which can generate power from methane. These plants are further enhanced by harnessing waste heat produced in the generation process. The installation, automation control and monitoring of these plants incorporates many facets of engineering from high voltage power supply and computer technology to complex gas handling procedures used in gas compression storage.and generation of electric power.

Jan 1, 1982

By Liu Q, Siefken T. C, Misra V. N

The bubble size was measured in a laboratory flotation column. The effect of variables such as air flowrate, frother dosage and type, pulp density, particle size and water column height on the bubble size was investigated. The results show that an increase in either air flowrate or pulp density cause the bubble size to increase, while increases in water column height, frother dosage, surface tension or solid particle size cause the bubble size to reduce. Among the frother types tested, MIBC was found to be the most effective in reducing the bubble size.

Jan 1, 1992

In 1556, Agricola noted that "a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him"(1). In today's world, the owner rarely has the opportunity to visit the mine and, instead of reading about the `nature of the vein' in annual reports, prospectuses, government publications, et cetera he sees the words `reserves' and `resources'. Unfortunately, the subject of reserves and resources has become increasingly complex and Canadians, along with their counterparts in Australia and elsewhere, are still struggling with definitions which will attempt to cover all conceivable circumstances from national or regional resource endowment to the material to be extracted next week from a given stope or open pit bench. The providers and recipients of reserve and resource data are: - Government agencies who are concerned with questions of national endowment, strategic use of raw materials and other questions of public policy. - Stockholders who have a vested interest in the basic assets of their companies. - Financiers who are concerned about the security of their loans. - Regulatory bodies whose function is to protect a frequently naive investor from unscrupulous practices. - Management, at head office and on-site, who need basic information for decision-making, whether it be to open up a new mine, expand or close an existing operation, acquire or merge with other entities, or, more mundanely, for routine mine planning. To satisfy their demands with unanimously accepted definitions is a formidable task but, it is my impression that, little by little, a concensus appears to be growing within the industry.

Jan 1, 1987

By P Gilroy

In recent technical investigations that were triggered from ore for rail shortfalls at Yandi, BHP Iron ore has identified a gap in resource knowledge relating to geo-metallurgical characteristics that predict materials handling performance and throughput. Within these investigations BHP has learnt that this lack of resource knowledge has translated to a lack of predictability associated with mine planning inputs which has resulted in poor compliance to plan and deviation management practices. A business value chain was developed in an attempt to identify the best possible solution to unlock this resource knowledge in the short, medium and long term planning horizons. A fast fail approach was taken with the implementation of hyperspectral blasthole analysis, which was chosen to deliver the best possible value driver for the asset. This report will detail the Yandi journey in expanding the hyperspectral and geo-metallurgical value chain, unlocking resource knowledge along the way. CITATION: Gilroy, P, 2018. Development of an empirical geo-metallurgical model that unlocks value of the mineral resources at Yandi Mine, in Proceedings Complex Orebodies Conference 2018, pp 85–87 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Roadheaders have had a chequered history in hard rock excavation in Australia since their introduction into the country in 1972. This has resulted in a poor reputation among both clients and contractors and subsequent reluctance to design tunnels and underground space around their performance characteristics.This has now changed because of the introduction into Australia of a new breed of Roadheader, the Mitsui. This paper sets out the history of development of the Mitsui range of Roadheaders. It describes the process which resulted in the introduction of this new machine, its performance to-date and the characteristics which have contributed to the success of the machine. The combination of these factors have led to a change in attitude to the use of Roadheaders in underground excavations.

Jan 1, 1993

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

By De Jong HJ

During the forthcoming reline of No.3 Blast Furnace at the Newcastle Steelworks of the Broken Hill Proprietary Co. Ltd., facilities for the screening and weighing o' coke will be installed. The equipment is needed to optimise the sizing and the quantity of coke immediately prior to it being charged to the furnace. Up till the time the furnace was blown out in November, 1982, coke was charged to the furnace by volume, ie by skip fulls only. This resulted in variation to the ore/coke ratio charged due to bulk density changes and erratic skip filling levels. This in turn affects the heat balance of the furnace and causes fluctuations in hot metal chemistry and temperature. A coke rate penalty has to be paid also. Coke layer thickness in the furnace burden cannot be controlled closely, resulting in loss of control over gas distribution in the furnace. A grizzly type screen was incorporated in the skip loading chute but this ineffective method left a great amount of fines with the coke being charged to the furnace. Furnace permeability was therefore reduced, particularly in the hearth.

Jan 1, 1984

Jan 1, 2004

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By Turco E, Pelizza S, Vona A

Within the project against pollution in the Gulf of Naples (Italy) it was envisaged to build a sewage collection tunnel whose tunnelling section is about 30 m2 and whose length is over 4 km. The formations to be bored through feature heteregeneous volcanic deposits made up of either lenses or lava, lapilli and pozzolan layers and ashstone silts. The cover ranges between 10 and 30 metres. The surface is heavily built-up requiring then an accurate monitoring and reduction of noise, vibrations and settlements. The building of the tunnel is therefore carried out by means of a boom tunnelling machine equipped with a mechanized shield. Support along the complete excavation perimeter is provided by linerplates together with an immediate cement grouting behind them. At a later stage the concrete lining will be cast in place.

Jan 1, 1987

By Chang TS, Suzuki K, Go H, Nakamura S, Kuwano Y

In 1979, a test operation of an experimental blast furnace was carried out to investigate the behavior of a sort of formed coke, which was used safely by 30% of total coke charge in No.2 B.F., Sakai works, NSC, in 1975". The Mashec-type formed coke of 60 x 60 x 40 mm in dimension was crushed and screened so that it had the same size range (1011,20 mm) as ordinary coke used in the base operation. Preceding to the operation, some experiments on the properties of the formed coke and the effects of crushing on them were performed.

Jan 1, 1981

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

By Pollmans GJ, Hoberg H, Schneider FU

The Institute of Mineral Processing at Aachen University of Technology has been engaged in fine and ultrafine comminution for several years. Former investigations had been dealing with the mechanical activation with the aim of increasing the solubility of highly resistant oxides such as tantalite and niobite while research on the product of ultrafine powders is of major importance at the moment. Materials of that kind are of increasing interest in the production of extremely resistant ceramics, in the development of new raw materials, in powder metallurgy and in the production of fillers (extender pigments) and pigments. The creation of ultrafine powders is difficult and very expensive. They can be produced by means of condensation or dispersion methods. One important method of dispersion is mechanical comminution. Due to long and intensive research and development all over the world important advances have been achieved but still a great number of questions and problems occur especially in producing materials of submicron and nanometer grain sizes which could be answered or solved only insufficiently up to now. These mentioned difficulties refer especially to: ò the required energy input into the feed material, ò the forming of strong agglomerates and wall stickings, ò the required product qualities, and ò the entire and reliable characterisation of the products. Basic investigation aim to clarify the micro and macro processes of ultrafine grinding and work towards solutions to the difficulties mentioned above. The aim of the Institute's research is the development of a new grinding device for producing ultrafine powders. First results of a laboratory scale mill of that type will be presented in this paper.

Jan 1, 1993

By Mingmin Dou

The behaviour and deportment of indium during the precipitation of sodium jarosite from Fe2(S04)3 - Na2SO4 solutions were investigated. Indium is readily precipitated with sodium jarosite, and the extent of In precipitation increases as the In concentration of the solution increases. It was shown that In 3+ substitutes for Fe 3+ in the jarosite structure to form a nearly ideal solid solution series. On a molar basis, the precipitation of Fe is slightly favoured over that of In, and the difference is reduced as the pH increases. Sodium jarosite precipitation becomes kinetically rapid at temperatures >70¦C, but increasing temperatures in the range 70 to 150¦C affect neither the relative precipitation of In and Fe nor the composition of the jarosite product. Low Na2SO4 concentrations result in reduced product yields and jarosite precipitates in which H3O' > Na+. The hydronium-rich precipitates have reduced In contents. Increasing the ZnSO4 concentration of the solution slightly increases the quantity of jarosite formed and results in the incorporation of -0.3 per cent Zn in the jarosite structure. Otherwise, the presence of ZnSO4 has no significant effect on the composition of the jarosite. Seeding accelerates the rate of jarosite precipitation but has a negligible influence on the deportment of In. The jarosite precipitation reaction at 98¦C is relatively rapid and near-steady state conditions are achieved in - 6 h even in the absence of seed. The initially precipitated jarosite is slightly enriched in In with respect to Fe. The ferric ion concentration of the solution has a significant influence on both the amount of jarosite formed and its composition. In particular, the jarosites precipitated from dilute Fe3+ media have significantly enhanced In contents. Hence, it may be possible to recover - 25 per cent of the dissolved In, at the 1000 mg/L level, in a jarosite precipitate assaying - ten per cent In by the controlled oxidation-precipitation of sodium jarosite from a ferrous sulphate processing solution.

Jan 1, 1993

By White A. H, Vihena M. T M B

Presently, orebody modelling consists basically of fitting a mathematical model to represent spatially a certain geological variable, generally grade. An orebody model is constructed from a set of sample data obtained from various locations in the orebody, thus it is only one form of representation of the true phenomena. Checking the compatibility of the data with the modelling procedure is the most important factor when assessing confidence in the orebody model. The level of confidence in the model will depend on the adequacy of the data set and the validity of the basic assumption required by the modelling method. Fractal geometry is one way of modelling the spatial distribution of a geological variable in an orebody geometry. Fractals can be used to interpolate the Z(x) geological variable at unsampled sites. The concepts of self similarity and self affinity that form the basic assumption of fractal geometry theory which areinvestigated. The population distribution of the geological variable in question must be examined to determine the appropriateness of both fractal geometry and geostatistical modelling methods. The selection of the most appropriate method depends on the available data. A researcher or a practitioner needs to understand the strengths and limitations of the various modelling methods before choosing the most appropriate method. This study investigates the fractal properties of grade distribution using the variogram and some proposed variations as techniques to measure the fractalness. The aim is to assess applicability of fractal geometry theory to modelling ore grade distribution in a deposit. A comparison of the results demonstrates the methods which better capture the spatial behaviour of the variable under study.

Jan 1, 1995

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

SITUATED in the county of Manchcster, in Northern Eyre's Peninsula, the Iron Knob ore-deposits form the basis of the industry. These deposits are connected by the Iron Knob tramway to the port of Whyalla, aal miles distant, on the western shore of Speneer Gulf,and to-day another tramway is under construction to link up with the same port, a second group of iron ore leases known as Iron Baron, which is situated 18 miles south of Iron Knob. Fig. 1 indicates the geographical relationship of these three places, Iron Knob, Iron Baron, and Whyalla, which together comprise this field of the company's activities.

Jan 1, 1930