Search Documents

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

The iron ore mining operations carried out by Goldsworthy Mining Limited at Golds- worthy, Shay Gap and Sunrise Hill, in the Pilbara region of the North-West of Western Australia, are unusual insofar as the ore reserves occur in a number of widely separated and relatively small deposits, requiring deep mining below the water table, and even below sea level at the Goldsworthy pit. This paper has been prepared to describe some of the problems associated with these deep open cut mines, and the technology employed to overcome them, in order to provide an efficient and economical operation. The problems discussed are: 1. Development of the Dewatering System for the Goldsworthy Mine. 2. The Stability of Pit Slopes at the Goldsworthy and Shay Gap Mines. 3. Development of Diesel Electric Trucks for Lonq Uphill Hauls.

Jan 1, 1979

By Terrill JE, Fergusson LJ

In the last decade of precious metal exploration, several important gold discoveries have conclusively demonstrated that epithermal gold deposits formed in what were once active geothermal areas. A significant deposit in this category is the Lihir Island discovery in the Tabar-Ferri volcanic island arc off the coast of New Ireland, Papua New Guinea. Within that arc are the Feni Islands where exploration by Esso PNG Inc. and City Resources Ltd. has been carried out since early 1984. On Ambitle Island in the Feni Group, an epithermal gold prospect located within a young caldera has been tested by diamond drilling. The drillholes intersected a boiling zone at depth beneath acid altered 'cap' rocks. The zone is 30-60 metres thick and comprises hydraulically fractured and mineralised lavas with gold grades of 1-7 g/t. The prospect is still an active geothermal area with current boiling in the zone tested. As on Lihir, the recent epithermal alteration and mineralisation overprints a relict prophyry system. On Ambitle and the adjacent Babase Island several other, cooler exciting gold prospects are currently being tested.

Jan 1, 1987

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991

The New England Fold Belt forms the easternmost and youngest section of the Tasman Fold Belt System of eastern Australia. From middle Palaeozoic to Early Cretaceous time it was the site of extensive episodic calc-alkaline magmatism related to W-dipping subduction. The oldest rocks may have formed at least partly in a volcanic island arc, but from the Late Devonian, the fold belt developed as a convergent Pacific-type continental margin. For Late Devonian-Carboniferous time, parallel belts representing continental margin volcanic arc, forearc basin and subduction complex assemblages can be recognised. Major dextral transform faulting may have offset parts of the fold belt in the Late Carboniferous. In addition, some structural blocks which appear to be out of place in the overall palaeogeographic setting are possible exotic or suspect terranes. A great variety of lode deposits ranging in age from middle Palaeozoic to Early Cretaceous is present in the New England Fold Belt. The vast majority of these are related to emplacement of extensive granite plutons and eruption of continental silicic volcanics in Late Permian-Late Triassic time. However, volcanogenic massive sulphides and volcanic hosted epithermal gold-silver deposits in older rock sequences include one major orebody (Mount Morgan) and several important ones (Mount Chalmers, Cracow, Silver Spur, Cangai and Halls Peak). Some problematical deposits are best classified as metamorphic-hydrothermal. These include gold-bearing quartz reefs and stockworks in sedimentary host rocks, the most important of which are at Gympie, and antimony-gold- tungsten mineralisation in the New England area, mainly at Hillgrove.

Jan 1, 1987

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

An automated method, which is believed to be the fastest in the world and which can be used by mineralogically-untrained technical assistants, has been developed for the rapid location of native gold particles and other gold minerals down to 1 pm in size in ores, concentrates, and tailings using a scanning electron microscope. Searching of a 25 mm diameter polished block in 1 pm steps usually requires 3-4 h. Examples of the location of native gold and gold tellurides in drill core sections, in crushed ore samples and gravity and flotation concentrates, and in various metallurgical test products are given. The results have application in ore exploration, in guiding metallurgical test programmes, and in assessing metallurgical per- formance in testwork and in operating plants.

Jan 1, 1991

A very sensitive high-speed two-colour pyrometer was built to measure the temperature of single particles of sulphide mineral, typi- cally 50 pm in diameter, as they burnt while entrained in a hot gas stream. The pyrometer has been used to study the burning of pyrite and chalcopyrite particles and has thrown light on cenosphere formation. Measured maxi- mum temperatures have been compared with values predicted by diffusion-based models. The pyrometer has also been used to study the burning of small captive pellets (2-9 mmm dia- meter) of lead-zinc concentrate.

Jan 1, 1984

By Kepplinger W

The COREX process is a technology for production of liquid hot metal on the basis of coal (without the use of a coking plant) developing by VOEST- ALPINE AG, Austria and its subsidiary company Korf Engineering GmbH, Federal Republic of Germany. CORED is a registered trademark of VOEST-ALPINE AG and Korf Engineering GmbH. The COREXW process is based on the idea of separating the process steps realized in the blast furnace (gene- ration of reduction gas, reduction of iron oxide and melting of the reduced iron) and including partial coking of the coal.

Jan 1, 1987

By Fullagar P. K

In resource definition and mine development, major capital expenditures are committed on the basis of sparse information and even in production surprises such as bad ground are not uncommon. Drill holes constitute the principal source of information about the orebody and its environment and optimisation of drilling implies maximising the yield of useful information per dollar expended. Geophysical borehole logging provides new flexibility for optimising the drilling budget. Economic benefits can flow from geophysical logging at all stages of the mining cycle. The most commonly cited benefit is substitution of diamond delineation drilling with cheaper percussion or reverse circulation drilling in cases where geophysical logs can substitute for core. This approach can deliver an attractive direct saving in drilling costs (and time) if drill meterage is unchanged, or a potentially greater indirect benefit from better ore control if more holes are drilled within the original drilling budget. More ore contact intercepts per dollar can translate into lower dilution and enhanced ore recovery, thereby increasing revenue as well as reducing mining costs. Substitution of diamond drilling with percussion drilling is not always feasible. However, geophysical logging of diamond holes is often highly advantageous in its own right, both for geotechnical characterisation as well as ore delineation. Operational advantages of logging include data objectivity, speed of interpretation and reduced core handling and analysis costs. Geophysical logging assists mining engineers by providing a continuous measure of in situ rock strength, even over intervals with poor core recovery. The additional expense of geophysical logging in blast holes can be justified in terms of more accurate ore boundary delineation and rock strength evaluation. Precise ore boundary delineation permits refinement of charge placement, to minimise dilution and maximise recovery. Detailed knowledge of rock strength can enable optimisation of blast design. Rock strength can be evaluated in real-time via analysis of drill performance data recorded with measurement-while-drilling (MWD) technology. To successfully apply geophysical logging in mines, its technical, operational and economic viability must all be established. This entails verification of the existence of appropriate physical property contrasts, investigation of the best way to integrate the geophysical results with the mining method and an objective assessment of the value of the resulting mine performance benefit. Geophysical logging is already well established in many mining operations. The greatest impediments to its wider utilisation at mines are: lack of appreciation of geophysics by most mine geologists, engineers and managers; limited interpretational aids; and the necessity to re-enter completed drill holes. In this paper we endeavour to address these issues by informing mine geologists about potential applications of geophysics, by illustrating automated interpretation of geophysical logs and by highlighting the importance of emerging MWD and logging- while-drilling (LWD) technology.

Jan 1, 1997

Maximising margins in highly competitive international markets demands superior productivity. A key to superior productivity is using a process approach to enable rapid, ongoing improvement of production, commercial, administrative, marketing

Jan 1, 1998

By Just J, Nguyen G, Dunn J. G, Graham J

A sample of pyritic gold concentrate was investigated by wet chemical and electron optical techniques. Sub-samples were roasted in a laboratory scale fluidized bed roaster in the temperature range 400-700¦C. The calcine was characterised, and cyanide-leached using a standard bottle rolling test. Gold extraction efficiencies varied with roasting temperature. At temperatures of 400 and 450¦C gold ex- tractions of less than 40% were achieved, but between 500-700¦C the extraction had increased to 93--98Z. The surface area of the calcine varied with roasting temperature, reaching a maximum at 500¦C. There was no correlation between the surface area of the calcine and the efficiency of gold extraction.

Jan 1, 1987

Within the Business Process Improvement Program initiated at Placer Dome during 2003 was the Business Performance Management Project (BPM).BPMÆ s aim has been to extract productivity improvements from individual business units by providing a model for implementing leading practice based management process within the Placer Dome Group, sharing management best practice, injecting new management techniques and instilling a continuous improvement culture. The installation of an underground dispatch system has been a key component of the BPM project at Osborne Mine.Information capture and analysis allows for corrective action to be planned and executed before there is a material impact on the performance of a business unit. This paper briefly describes the principles and practices of effective business performance management, the four processes of a management operating system namely; strategic and tactical planning, implementation and reporting. The identification of business drivers, their measures and associated key performance indicators is discussed. The benefits of an underground dispatch system at Osborne with respect to safety, production and maintenance is described along with the installation process within the mining department that included its configuration, resourcing and roll out.

Jan 1, 2005

By Wilkinson RDB, Van Der Meer FP

In order to overcome the statistical limitations imposed by the need to recover density tracers by hand, magnetic density tracers were developed to determine the efficiency of dense medium separators treating porous materials. The tracers were manufactured by extrusion of polypropylene ferrosilicon mixtures and subsequently coated with a distinctive paint to allow hand sorting according to density. Fifteen tracer batches were manufactured in the range 1.61 - 1.94 g/cm3. The tracer densities were determined by a hydrostatic method. The tracer method was applied to the dense medium separation of a Moroccan oil shale in a pilot scale Dyna Whirlpool separator. For each test, about 20,000 tracers were added with the plant feed and subsequently recovered from the products with a dry low intensity magnetic separator. The Tromp curve determined by conventional heavy liquid analysis was displaced towards lower densities compared with that determined by tracers, indicating that the porous shale particles absorb heavy liquid. It is concluded that for porous materials like oil shale and coal, the tracer method gives the most accurate results. In pilot scale testwork the tracer method is also much faster than the conventional heavy liquid analysis, as rather large samples have to be processed by the latter method to ensure Representativeness.

Jan 1, 1987

The operators of the iron ore railroads in the Pilbara faced problems of excessive wear between rail and wheels as the tonnage hauled increased in the early 1970's. Joint research projects were begun between Hamersley Iron, Mt Newman Mining and the BHP Melbourne Research Laboratories to study these problems and recommend solutions. The particular problems of wheel rail interaction were solved by asymmetrical profile grinding of the rail and modifications to the machining of the wheels. Rail materials were improved through increasing yield strengths by alloying and by heat treatment. Wheel materials were improved by alloying. The economic benefits of these improvements have been demonstrated by much reduced re-rail requirements and other reduced maintenance costs.

Jan 1, 1986

By Watkins JR

Movements in the mineral trade cycle are almost invariably out of phase with the gradua- tion rate of mining engineers, metallurgists and geologists. This commonly leads to situations where graduates are scarce in "boom" periods and in free supply when the trade cycle is depressed. This problem reflects the difference in elasticity and flexibility between the educational and industrial environments. In the educational system the decision that brings students to graduation is made three to five years prior to the event. This is quite a lengthy period of time in terms of mineral trade cycles. By contrast, the mineral industry has far more elasticity in responding to short term fluctuations in mineral trade. The authors do not believe that the mis- match between the availability of skilled personnel and the manpower requirements of industry in the short term is intractable. Much is to be gained by more realistic and rational manpower forecasting combined with greater flexibility in the educational realm.

Jan 1, 1982

Over the 20 years to 1990 the Australian mining industry, presently worth some $A60 billion, generated a negative real rate of return (McDonald, 1992); not surprisingly under-performing the returns from bonds and industrial equities. Over this same period more than $A70 billion was invested in expanding the Australian mineral industry.

Jan 1, 1993

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC's) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990

Rare-earth permanent magnetic roll separators, pioneered by our group a few years ago, have distinctly different operation characteristics compared to prior art electromagnetic separators of various types. Many new applications for dry high-intensity (or better: high-force) magnetic separation have been developed in a short time period. It has also been found that the new generation of separators generally are more efficient with regards to removal of weakly magnetic contaminants in glass and ceramic raw materials with minimum loss of valuable product compared to induced magnetic roll (IMR) separators.The latest development is in the area of production of clean magnetic concentrates at high recoveries. It is likely that the PERMROLLR magnetic separator will replace cross-belt and lift-type magnetic separators as a result of this most recent advance.The paper will review the features of the PERMROLLR magnetic separator in comparison with other types of magnetic separators on the market and give examples on applications.

Jan 1, 1990

By Harmse C

Gold mining in Vatukoula had been a low tonnage/high grade operation for much of its 55-year life. During 1991 it became clear that a change in direction was needed if the mine was going to continue to prosper. The challenges of ore reserves of only three years, the prevailing gold price and high infrastructure and fixed costs combined to force changes in mining strategy.A more productive mining method was required to lower the unit mining cost, lower the pay limit and make more effective use of the resource.The flat dipping mineralised faults or flatmakes had been mined by updip, handheld room and pillar methods with a more recent trackless development adaptation. Furthermore, up to 40 per cent of the resource was left in pillars and broken rock.

Jan 1, 1993