Search Documents

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

By Storey AG

Following initial plant scale work on the development and performance of 'spray' oil lances, a full scale room temperature model of the blowpipe-tuyere region of a blast furnace was built to study the basic aerodynamic features of auxiliary fuel injection procedures. Mobilwax 2305 was used as a substitute for Bunker C oil fuel in view of its similar physical properties and the fact that the atomised droplets could be frozen in flight and size, distribution analyses made for various operating procedures. It was shown that secondary atomisation processes far outweighed the importance of any primary atomisation procedures in determining mean Sauter Diameters particularly at high windrates typical of current blast furnace technology. It was also found that good spray dispersions across the blow pipe could only be obtaind for liquid fuels and that the lateral rate of spray dispersion was substantially enhanced by primary atomisation procedures. Mean particle diameters of sprays were found to be predictable on the basis of elementary stability theory and fell within the size range necessary for good combustion at all liquid fuel rates studied. The possible effects of high oil injection rates on flooding phenomena in the furnace bosh were considered. Comparisons show that high oil rates can lead to significant increases in the hanging factor (e.g. 'V 10% at 135 kg oil/thm) owing to increased gas flow rates/thm resulting from the presence of hydrogen.

Jan 1, 1975

By Wharton P, Voigt R

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

By Glenn R. J

Treatment processes are outlined for the recovery of rutile and zircon from the heavy mineral-bearing sands on the east coast of Australia. With the exhaustion of the higher grade deposits and the imposition of more rigid specifications for the finished products, strict metallurgical control has become necessary.A description is given of the methods used by The Titanium Alloy Manufacturing Co. Pty. Limited to control the operation of suction dredging, of wet concentration using fans and spirals, and of dry separation using high tension and electromagnetic processes. By applying these methods a plant designed for an output of 15,000 tons of rutile per year has been tuned to produce over 20,000 tons of rutile and a corresponding amount of zircon.Details are given of (a) the method of drilling to determine the extent and grade of the ore bodies, (b) a simple electrically-timed pneumatic automatic sampler, and (c) the methods developed for the physical estimation of quartz, rutile, zircon, ilmenite and "others" in the products of plant operation.The method used for calculating the metallurgical balance and the forms used for the reporting of production results are presented.Examples are given which show the value of this detailed production and metallurgical control of plant operation.INTRODUCTIONThe organization which is now known as "The Titanium Alloy Manufacturing Co. Pty. Limited" (T.A.M.Co.)-a subsidiary of National Lead Company-commenced operating at Yamba, N.S.W., in 1935. A mixed natural concentrate was at first simply dried and bagged and later was upgraded by the removal of silica and the lighter heavy minerals on shaking tables and, after air-drying, was bagged for export. At that time zircon was the most wanted constituent.

Jan 1, 1960

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

By Mendeckl A. J

Anglo American Corporation has always viewed technological development as vital and as such has placed research and the implementation of new technological practices high on its priority list. Support is given to a number of research institutes but a significant degree of reliance is placed on in-house research carried out at individual companies and at the Group's main laboratory complexes. The Corporation's interests are diverse with advanced practices and innovative technology ranging from new battery technology with wide application to deep level shaft technology with very specific application. In this paper, we aim to concentrate on a particular system developed primarily for use in seismically active deep mines. The system has proved to have far wider application and has the potential to be further enhanced to meet the needs of users across a broad range within the industry and even beyond. As the nature of this conference is to inform delegates of advanced mining practices, we should simply mention that we could have talked on subjects relating to the advances made in deep level winding technology including winder drive and brake control to alleviate dynamic rope loads, shaft steel design for high pay load high speed winding and shaft safety systems such as slack rope devices and moving lip loading facilities to cater for rope stretch. Other areas of interest relating to refrigeration using ice technology or non-explosive rock cutting using diamond wire or saw technology could also have been of interest. As the South African gold mines become deeper and the problems associated with depth become more acute, answers had to be found and systems developed to cope with very high rock stress and the related seismicity. The fundamental understanding of the behaviour of the rock mass has always been important but became critical on our mines to ensure the safe extraction of the orebody. Basic research into and the application of physics, applied mathematics, seismology, rock mechanics, electronics and computer technology have helped us to develop the Integrated Seismic System - Integrated because of the system's abilty to monitor seismic and non-seismic sensors simultaneously and because it encompasses data acquisition, processing and interpretation into one system. The system which is in use at all our gold mines has found application not only in South Africa but also in such locations as Australia, Chile, Canada, Europe and Japan. A highly motivated team of scientists under the leadership of Aleksander Mendecki developed the majority of the hardware and software needed for the system. In essence, the system allows us real time monitoring of energy release and stress transfer data that with the aid of modern computers is turned into useful information. The information so obtained has allowed us to improve our mine and extraction designs to minimise the inherent hazards. The system has proved to be an extremely useful management tool as substantiated by the demand for the product. The paper is intended to convey to the reader the technical concepts and the presentation is intended to demonstrate the usefulness of the system.

Jan 1, 1995

By Takagi T, Seetharam R, Sie SH, Naito K

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medical/high-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnSZ), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

The paper first outlines the conceptual basis for evaluating and controlling geological risk. Geological risk, the economic reflection of the uncertainties associated with tonnage, grade, and other pertinent deposit parameters, is evaluated in terms of economic risk criteria. Delineation provides the deposit information required to appraise and control this risk. The improved reliability of geological estimates resulting from additional delineation reduces the economic risk associated with mine development and production decisions. However, the benefits of delineation, subject to diminishing returns, have to be weighed up against the direct and time costs involved. These costs decrease base case economic values and shift the probability distributions of possible outcomes towards, lower values. The optimum amount of delineation normally is achieved short of the point where economic risk is minimised, depending on the mining company's relative preference for a higher base case value or a lower economic risk. Then, two open pit copper mine examples, based on actual situations, are analysed to illustrate the application of the concepts presented. The first case concerns the extension of ore reserves at an operating mine. Finally, a new mine development opportunity is considered.

Jan 1, 1994

The implementation of the Mining Further Amendment) Act, 1970, and later the Coal Mining Act, 1973, placed a requirement on the Department of Mines to accept an initiative in relation to coal exploration and coal mine development which does not apply in the case of other minerals. It is necessary to consider the exploration of the total coal resources of the State when considering exploration rather than one individual basin or deposit. If the level of knowledge of the coal resources in these basins is considered in relation to their potential for development it is possible to allocate broad scale priorities to their assessment. Due to the enormity of the task which involves a conservative estimate of in excess of 400 000 m of drilling to reach a broad reconnaissance level of understanding the involvement of industry with the Department in the exploration programme is necessary. The development of the coal deposits by mining operations must give consideration to a number of constraints apart from the simple availability of the resources. Principal among these are aspects

Jan 1, 1976

By Sorentino C

Mineral valuation may appear to be a special field of financial valuation when in fact it is a subset of general investment decision theory. The only significant difference in mineral valuation is that in the case of valuing an on-going mineral asset, ie a mine, often there is no initial capital outlay involved. One is required to determine what the mineral asset as it stands is worth. But this is the same problem as determining the maximum one could pay today and not incur a loss over the life of the asset. In other words one needs to determine the Net Present Value (NPV) of the asset. The two most widely used discounted cash flow methods, NPV and Internal Rate of Return (IRR) came of age with the rapid adoption of the personal computer and spreadsheet programs. The two methods are directly related as the IRR is a special case of NPV. NPV measures the absolute increase in real wealth that can be expected from a certain investment, which makes it particularly suitable for mineral asset valuation, but ignores the efficiency of the investment. In contrast, IRR gives the expected efficiency of the investment but ignores the increase in wealth aspect. IRR has two serious theoretical weaknesses; multiple IRR's and a very rigid assumption about the rate of return of reinvested proceeds, plus if no initial equity expenditure is involved there is no IRR. The choice of the ""hurdle"" rate can also be a problem and in certain circumstances one can obtain different rankings of mutually exclusive projects using IRR and NPV. Although NPV and IRR supposedly measure financial risk, in fact they only address a very narrow area of risk, namely the time value of money given the real discount rate. They side step the issue of what the real discount rate should be and varying degrees of risk. The classical way to establish the real discount rate is to use the weighted average cost of capital.

Jan 1, 1994

At Renison Limited, on the West Coast of Tasmania, modern trackless decline mining is practised to exploit the various tin bearing sulphide deposits. With footwall accesses, one of three adaptations of horizontal mechanised cut and fill, 1. unsupported, 2. pillar supported,and 3. unsupported - resuing is used to stope each defined ore block. The stoping method is basically determined by the dip and true thickness of the ore with emphasis on high ore recovery. Extreme flexibility is possible by the selective mining of stope lifts, the consumption of development waste as fill and the utilisation of the same mobile equipment in all phases of production. This has resulted in high productivity and low cost per tonne of ore.

Jan 1, 1977

This paper discusses a number of examples of how environmental factors have been incorporated into the water management aspects of mining projects. One example is the Kingston Lignite Project in the South-East of South Australia where the most significant environmental issue was considered to be the effect of drawdown from mine dewatering and depressurization upon the use of groundwater. By proposing an alternative mining method - the use of floating dredges rather than a two-pass dragline method - drawdown effects would no longer be a concern. A second example is the Pine Creek Gold Mine in the Northern Territory. In this case the principal area of interest from an environmental viewpoint was water management - in particular effluent disposal, contaminated seepage from overburden and tailings, and project water supply. Through an integrated approach to the management of wastes and water the potential for water quality impairment was significantly reduced and external water supply requirements were also significantly reduced.

Jan 1, 1987

By Artone E

screening equipment installed in e Hamersley Iron operation is described, and tails of operating parameters and screening - Iia in use are given. Tests were carried out on full-size reens in the operating plants to study the Meets of mat aperture size, feed size distri 1,ution, feed rate, screen speed and throw, angle of inclination, and feed moisture content n screen performance. Sampling equipment was signed so that undersize samples could be htained from various locations along the length of the screen, thus providing information pout the quantity and size of particles passing òhro gh the screen at any point. Conclusions derived from the testwork and relevance of these to the Hamersley Iron aeration are discussed.

Jan 1, 1984

Precipitation of inorganic compounds or metals from aqueous solutions can either be physical (crystallisation) or chemical in nature. Chemical processes are varied; they may be due to hydrolytic action, due to ionic interaction, or due to reduction (ie transfer of electrons). Transfer of electrons in reduction processes may take place homogeneously or heterogeneously. In the first case it may be ionic or nonionic in nature. Heterogeneous processes may be electrochemical or electrolytic. Examples of interest to hydrometallurgy are given.

Jan 1, 1993

By Fulton E, Ring RJ, Waters DJ

Laboratory leach tests of Nabarlek uranium ore carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's Acid1 (permonosulphuric acid) as an alternative oxident to pyrolusite indicated reduced acid consumption in leaching and lime savings in neutralisation of tailings liquors when using Caro's Acid. Interox Chemicals Pty. Ltd. arranged a plant trial for Caro's Acid at Queensland Mines Nabarlek Plant. The trial confirmed that significant savings in acid and lime can be achieved under plant conditions. Plant operations also demonstrated improved redox potential control was possible using Caro's Acid.

Jan 1, 1978

By Hall S, Upton D

WMC Resources Ltd nickel operations have expanded significantly over the last three years. Production capacity has increased at mine/concentrate, smelting and refinery processes to such an extent that WMC now ranks within the top three or four producers of nickel metal in all forms. The stainless steel industry remains the dominant user of nickel. WMC's forecast is for stainless steel production to grow at 2.8 per cent per annum off of the 1995 peak, with much slower growth in the short-term as the stainless steel inventory overhang unwinds, followed by a return to higher trend growth rates. WMC's forecast for the long-term growth in demand for primary nickel is three per cent per annum off the 1995 peak; again, slower growth in the short-term before a return to higher long-term trend rates. This projection is towards the optimistic end of the range of industry experts. It equates to a requirement for new primary nickel of 25 000 to 30 000 tonnes of annual capacity each year.

Jan 1, 1996

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America. The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

By Visnovsky

The computing needs of a mine planning office vary greatly depending on the staff available and the nature of the work undertaken. Some offices work acceptably with few aids apart from hand held calculators while others use mainframe computers with associated data bases and sophisticated mine planning software. Not every mine planning office requires the big system approach but all can benefit from the intelligent use of small computers. There is virtually no limit to the design problems which can be solved using modern desktop computers. The simple language required encourages engineers to work interactively to facilitate both large and small computations. However a limit does exist in the speed and ease with which solutions can be obtained. The important ingredients for the successful application of such machines are a little computing knowledge, a flexible machine, and an engineer who really understands the mining problems confronting him. If these are available it is possible for the engineer to tailor the program to the task at hand and efficiently achieve the required result.

Jan 1, 1983

By Heape JM

Production from the Cattle Grid orebody commenced in August, 1974. This followed a recent discovery arising from an extensive exploration programme involving stratigraphic drilling, geochemistry and geophysics. Located some 4 km west of the original copper occurrences at Pernatty Lagoon the discovery was found to contain 4.6 million tonnes of ore averaging 2.4% copper. The ore is a "sandstone copper" type localised near the disconformity between two Precambrian (Adelaidean) stratigraphic units, the Pandurra Formation and the Whyalla Sandstone. The mineralisation roughly follows the interface between these units and occurs in fractures, vugs and along bedding planes. The mineralogical character of the ore is somewhat complex consisting of chalcocite and bornite, with associated chalcopyrite, sphalerite, pyrite and other less common sulphides. 1. Senior Geologist, Pacminex Pty. Limited, Sydney, N.S.W. 2. Mine Geologist, for Mt. Gunson Mines, Pacminex Pty. Limited, Mt. Gunson, S.A.

Jan 1, 1975