Search Documents

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A H. Bagherieh, S Mesroghli, H Jorjani, S Chehreh Chelgani

The rare earth elements (REEs) assay and recovery in leaching processes is being determined using expensive analytical methods, ICP-AES, and ICP-MS. This paper presents a neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, neodymium recovery in the leaching of apatite concentrate. The effects of leaching times: ten to 40 min, pulp densities: 30 to 50 per cent, acid concentrations: 20 to 60 per cent and agitation rates: 100 to 200 rpm were investigated and optimised on REEs recovery in laboratory at a leaching temperature of 60¦C. The obtained data, on the laboratory optimisation process were used for training and testing of a neural network. A feed-forward artificial neural network with 4-5-5-1 arrangement, was capable of estimating the REEs leaching recovery. Neural network predicted values were in good agreement with the experimental results. The correlations of R = 1 in training stages, and R =  0.971, 0.952, 0.985 and 0.98 in testing stages were results for Ce, Nd, La and Y recovery predictions respectively and that theses values are considerably acceptable. It was shown that the proposed neural network model accurately reproduces all the effects of operation variables, and can be used in the simulation of a REEs leaching plant.

Jan 1, 2008

By D Kentwell

A resource model serves two main purposes depending on the stage of a project. The first is to provide an early indication of likely tonnages and grades at certain cut-offs so that decisions can be made on whether continued spending on the project is justified. The second is to provide a basis for mine planning, feasibility studies and reserves. Resource models are not designed for selection of actual blocks in the ground for processing. This is the purpose of a grade control model, which is created at a stage beyond both resources and reserves.Inferred, Indicated and Measured Resources contain different levels of uncertainty with respect to the accuracy of the resulting grade and tonnage curves. These uncertainties arise from three broad areas: quality of information, geological assumptions and estimation technique. This paper focuses on known problems with the ordinary kriging (OK) estimation technique. Resource estimates often produce smoothed block grade distributions with much lower block grade variability than true selective mining unit (SMU) block grade distributions. There are two main factors that are involved in this smoothing. Firstly, where the block size used for estimation is larger than the SMU block size, this will smooth the block grade distribution and move the grade and tonnage curves away from the true SMU block grade and tonnage curves. Secondly, and less well recognised, is that smoothing is inherent in the OK estimator. This also moves the grade and tonnage curves away from the true SMU grade and tonnage curves, even when the estimate is done at the SMU block size. There are a number of techniques, such as simulation, uniform conditioning and degraded search neighbourhoods that can provide a better approximation of the true SMU block grade and tonnage curves at the expense of individual block accuracy.This paper aims to explore the extent to which OK resource estimates designed to maximise individual block accuracy can differ from (an estimate of) the true resource at SMU block size in terms of grade and tonnage curves. The differences at economic cut-offs and above are examined. In some cases these differences are significant. Both the OK estimation technique and block size play a part in the differences observed. To do this we will examine a number of commodities and deposit types using real project data.The conclusion is that the current industry standard default practice of targeting maximum individual block accuracy (conditional unbiasedness) using OK at resource stage, without consideration or evaluation of the extent of associated smoothing at SMU scale, can lead to significant errors in fundamental mine planning decisions. This then has implications for resource classification if the classifications are based heavily on the OK quality without consideration of the true SMU distribution.CITATION:Kentwell, D, 2014. Aligning resource estimates with mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By C Mark

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past two years, three US coal miners were killed in two coal bursts, following a six-year period during which there were zero burst fatalities.This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields that have struggled with bursts for decades. The Utah experience displays many of the ‘classic’ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley (NFV) also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders or other outbye locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper closes with a brief discussion of how US longwalls have managed the burst risk.CITATION:Mark, C, 2014. Coal bursts in the deep longwall mines of the United States, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M A. Rhamdhani, K Avarmaa, A Putera, J Chen, G Brooks

Silicon-based photovoltaic cells are currently the most dominant types applied to convert solar energy to electricity. In solar-grade silicon (SG-Si), the control of boron (B) and phosphorus (P) is very critical. Generally, these elements are difficult to remove into acceptable sub-ppm levels from lower grade Si. This study investigates slag treatment as a process for Si refining, focusing on the behaviour of P and B. The experiments were conducted by equilibrating Si-B-P alloys with 43 wt per cent SiO2 – 47 wt per cent CaO – 10 wt per cent Al2O3 slag under inert atmosphere at 1500°C. Different crucible materials were used (Al2O3, SiO2 and MgO), which determined the primary saturation phase for the system and modified the final slag composition accordingly. The samples were equilibrated and analysed with microanalysis techniques (EPMA (electron probe microanalysis) and LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometry)). New standards were prepared and applied in the LA-ICP-MS analyses. Experimental results show that silver is essentially fully dissolved in silicon, as well as most phosphorus with LP ( = wt per cent P in slag/wt per cent P in Si) between 0.1–0.3. The distribution coefficient of boron was measured to be between 1 and 2. The crucible material used had an influence on the phase compositions and slight influence on the distribution coefficients of boron and phosphorus. The experimental results provided new accurate data when considering applicability of slag treatment as a technique for Si refining and Si PV cell recycling.

Jun 19, 2024

By D Baas, D Bennett

This paper describes how Brisbane-based PanAust Limited develops process control strategies that are implemented at all operations and are used in functional descriptions for plant upgrades and new projects.The process control strategies are determined by operating management philosophies designed to maximise returns from the company’s assets.The approach is endorsed in the project planning and design phases to ensure facilities and equipment that form the major production assets are fit for purpose and capable of enabling the production managers and operators of the projects to maximise shareholder returns.PanAust’s process control approach has been to develop sets of process control standards which focus on two key areas. The first area covers hardware requirements and architecture, software objectives, control models and individual loop tuning methods. The second area defines control room layout, graphic standards and the alarm philosophy. The application of these standards in a new plant or upgrade decreases the time required to achieve design capacity and optimal performance.The PanAust process control strategy changes the operator’s role from one that controls a number of individual loops to one that sets the control objectives of the processing plant. To achieve optimal performance, all the process areas of the plant are analysed to identify opportunities to improve throughput, recovery and stability. Once a key opportunity is identified, a process control strategy is developed which defines the objective of the control, its functionality and how an operator will interact with it. After development of the control model the operators assist engineers to test and debug it. Once the model is robust, it can then be duplicated throughout the group and developed as a group process control standard.CITATION:Baas, D, Bennett, D and Walker, P, 2014. Developing process control standards for optimal plant performance at PanAust Limited, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 325–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Laajalehto K

The basic condition necessary for flotation is hydrophobicity of the surface of the mineral to be floated. For sulphides, this condition usually requires treatment with a collector solution. The conditions for this treatment have until recently usually been chosen by the trial and error principle which has indeed been working relatively well under favourable conditions; ie for simple homogeneous ores. However, the present tendency to increasing use of complex and often relatively lean ores sets increasing requirements for the control of the flotation process. This development is the reason for the present rapid development of process control methods in flotation. In addition to the already well-established practices of pH and reagent feed controls, the importance of measuring and controlling the electrochemical potential of the ore particles to be floated is recognised in the case of sufficiently conductive minerals. In fact, the electrochemical potential seems to be the basic quantity determining the flotation behaviour of such relatively well-conducting minerals as sulphides. Since the hydrophobicity of the mineral and, hence, its flotation properties are ultimately determined by the composition and structure of its surface, information on these under different process conditions is important for design and operation of efficient flotation processes. The basic requirement set for the methods used for obtaining this information is high surface sensitivity of the method. The recent rapid development of surface characterisation has produced several methods which fulfil this requirement. Their application to the problem of characterising surfaces of mineral samples in contact with collector solution is, however, often complicated. The main reason for this is the vacuum environment necessary for the measurement. In the case of flotation experiments this means that in most of these methods the measurement cannot be made in situ, but the sample must be extracted from the liquid and subsequently evacuated in the vacuum chamber of the instrument. It is essential to carry out these steps so as to avoid to the extent possible changes in the sample surface. For the purpose of establishing whether this has been accomplished it is important to compare the results of methods operating in vacuum with some available in situ method. An optimal choice of methods seems therefore to be a combination of the available powerful vacuum methods with in situ measurements. The most usual combination seems to be X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. This choice combines the unique possibilities for direct elemental and chemical characterisation offered by XPS (Cecile, 1985) with the in situ capability of FTIR and electrochemistry. In the XPS measurements, it is essential to apply a special sample handling technique to avoid loss or damage of some sensitive species of the collector-based layer on the mineral surface. In the following will be given some examples of the application of the XPS technique in combination with electrochemical methods of sample treatment to studies of the layer formed on sulphide substrates in ethyl xanthate (EX)

Jan 1, 1993

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By I Ametov, S Harmer, R Alford

A process that allows selective flotation separation of low Cu/S ratio minerals (chalcopyrite and pyrite) from high Cu/S ratio minerals (bornite and chalcocite) from a mixed copper mineral concentrate under controlled oxidative-reductive potential conditions has been developed. The process has been extensively tested on samples with varying mineralogy using laboratory batch flotation tests and mini pilot plant trials.In this process, the mixed final copper mineral concentrate is purged with nitrogen, and then treated with sodium dithionite to achieve a slurry Eh in the -200 to -100 mV standard hydrogen electrode (SHE) range. Flotation was then carried out using nitrogen gas. As a result, a low Cu/S ratio concentrate (<1.3) and a high Cu/S ratio (>1.6) tailing stream were produced. QEMSCAN analysis of the flotation products showed that more than 85 per cent of the chalcopyrite and 95 per cent of the pyrite reported to the froth concentrate. Chalcocite and bornite were almost evenly distributed between the concentrate and tailing streams.Surface analysis studies, focused on the mechanism of separation, showed that at a negative redox potential xanthate and possibly dixanthogen are the dominant hydrophobic species on the surface of chalcopyrite and pyrite. As a result, the flotation of these minerals remained unaffected. In contrast, a much lower concentration of xanthate species on the surface of chalcocite and bornite particles was observed. Therefore, it is likely that at low Eh the copper xanthate complex desorbs from the chalcocite and bornite surfaces, causing a decrease in surface hydrophobicity and the diminished floatability of chalcocite and bornite.CITATION:Ametov, I, Harmer, S, Grano, S and Alford, R, 2014. Selective flotation of chalcopyrite and pyrite from a mixed copper mineral concentrate under controlled redox potential conditions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R Polmear, G Mauger

You wouldnÆt start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players canÆt produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International PowerÆs Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power HazelwoodÆs (IPRH) experience are: that the clear set of project principles and guiding values ensured delivery of a robust plan; a robust plan can withstand significant change; and value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

By A Salama, J Greberg, B Skawina

In today’s underground mass mining, the orepass is an important part of the infrastructure as it connects two or more mine levels and is used for conveying or storing large amounts of material. One of the main risks related to an orepass is when operational or structural failure occurs, leading to long-term loss of functionality. Developing or rehabilitating an orepass when major failure has occurred is a time-consuming and expensive operation, and the risk of a long-term orepass loss motivates the development of alternative transportation strategies to ensure the continuation of smooth operations in large underground systems. The study presented in this paper has been done at the Loussavaara Kiirunavaara AB Malmberget mine in Sweden, where iron ore deposits are being extracted using sublevel caving. The study analyses the transportation system in one of the mine’s orebodies using discrete event simulation, with a focus on maintaining ore transportation in the event of the loss of an orepass.CITATION:Skawina, B, Greberg, J, Jonsson, K and Salama, A, 2016. Orepass loss mitigation approach in Malmberget mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 617–622 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A D. Caccioppoli

Grade control systems within Rio Tinto Iron Ore have proven to be robust, when mining full benches. The Hope Downs 1 operation hosting two Marra Mamba Iron Formation deposits (North and South Deposits) presents a new challenge, where increased mining selectivity due to moderately plunging N-verging folds has made flitch mining necessary in the South Deposit. Poor flitch blasthole sample duplicate results in South Deposit over a 12 month period, compared to North Deposit, have highlighted concerns with grade predictions. In contrast a new grade control methodology (grade splitting) was proposed to alleviate blasthole sampling bias, utilising geological mapping and mineralogical logging, currently practised throughout Rio Tinto Iron Ore Pilbara operations, to estimate theoretical grades for each flitch from a single blast cone assay. To assess this method, reverse circulation holes (RC) were twinned to blastholes establishing an ‘actual’ grade. These blastholes were assayed using current flitch sampling techniques where: flitch positions were estimated, flitch positions were marked with paint, and a full cone sample was taken for ‘grade splitting’. Using these data sets multiple grade predictions were produced, then analysed using Half Absolute Relative Difference (HARD) statistical analysis. In addition to testing these grade control methodologies two other findings were ascertained: an inherent bias in blasthole assays exists particularly in the top flitch, where an average absolute difference of 0.6 per cent in SiO2 and 0.42 per cent Al2O3 was measured; and assays derived where kaolin rich soft shales are intersected were less representative. This is likely to be due to these materials not being properly represented in blast cones. Grade splitting accurately estimated block chemistry, except for a slight under-prediction in Al2O3 and P compared to current grade control methodologies. This method is a viable alternative where grade distribution is stratigraphically controlled.

Aug 22, 2011

By M Allen

By its nature, the mining industry is energy and emissions intensive. In the future, the world will still require the outputs of mining but the industry will need to adapt to the low emissions economy. Understanding the risks of climate change to a particular site or at a company level is key to managing this transition.CITATION:Allen, M, 2018. Assessment of climate risk in the Australian mining industry, in Proceedings Life-of-Mine 2018, pp 13–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

A very wide range of technologies are utilised in the mining and processing of ores and a great deal of effort is expended in the development of ænew technologiesÆ to improve mining performance and economics. Traditionally, technology and people have been treated as separate aspects of an operation, when in fact they are inextricably linked. The successful implementation of new technologies is entirely dependent upon the actions, enthusiasm and skills of people, both as individuals and working in groups. This paper discusses the role of technology in mining and how new technologies are implemented by the industry. The paper argues that existing technologies have not been fully or adequately utilised and that effort should be re-focussed on the implementation of technologies that have been taken for granted for many years. The need for greater emphasis to be placed on the management of the human-technology interface is discussed.

Jan 1, 1998

By B Johansson

The mining industry needs to recruit young talented people. An important task therefore, is to create future attractive mining workplaces that engage and motivate young people to work within the industry. Our intention with this article is to illustrate a possible way forward for the mining industry to form such workplaces. We discuss different aspects of an attractive workplace and summarise our findings in a specification of basic demands dealing with safety, physical and psycho-social work environments and social responsibilities.

Nov 22, 2011

By N Clarke, J Hunt, A Barros, L Keeney

The Gramalote orebody is a large low-grade gold deposit situated in the San Roque municipality, 124 km north-east of Medellin in Antioquia, Colombia. It is jointly owned by AngloGold Ashanti (AGA) and B2Gold and is currently in Feasibility Study phase. In 2013 AGA requested CRCORE to undertake a preliminary study of the potential application at Gramalote of pre-concentration by screening, part of the Grade Engineering suite. 160 samples of coarse assay rejects (-3 mm) were tested and showed one of the strongest responses seen worldwide to that time, suggesting that about 70% of the gold could be recovered into 40% of the mass. This was seen as potentially markedly improving the Gramalote economics. A large-scale testing program was implemented on site to follow up these results. A total of 18 samples of 17 t each were mined along a pre-existing exploration adit. A complex test flowsheet allowed size fractions to be generated from the as-received material as well as after crushing to 53, 23 and 3 mm, all from the same head sample. The procedures were designed after carrying out a heterogeneity study to measure sampling errors. The coarser size fractions were designed to study the effect of crushing on upgrade response and predict the response on open-pit run-of-mine ore. The finer size fractions were designed to investigate means of predicting the upgrade response across the orebody. The large-scale testing closely confirmed the average upgrade response as predicted from drill core assay rejects but found that only the -53 mm crushed material accurately predicted the upgrade response of individual samples. Ore geochemistry was able to usefully distinguish samples with good and poor response. A small study on drill core suggested that, for Gramalote, fine crushed material distinguishes vein associated and disseminated values but not other factors that control actual outcomes.

Nov 10, 2020

By J H. Park, R R. Kim, H S. Park, H J. Kim

This study focuses on the recovery of valuable metals, specifically silver (Ag) and palladium (Pd), from copper-containing sludge (with copper content less than 20 per cent) generated during PCB processing and from spent petrochemical catalysts used in vapour decomposition during oil refining processes. The present results indicate that an increase in the mixing ratio of alumina-based spent catalyst leads to a decrease in the recovery rate of Ag and Pd. The recovery rates for Ag and Pd range from 84 per cent to 96 per cent and 80 per cent to 98 per cent, respectively. This trend is attributed to the increased emulsification of copper droplets containing Ag and Pd in the slag. The emulsification is caused by the decrease in the settling velocity of the copper droplets due to the increased viscosity of the slag as well as by the decrease in the slag-metal interfacial tension due to an increase in sulfur content at higher mixing ratio of spent catalyst.

Jun 19, 2024

By H R. Phillips

During the 1980s and early 1990s, the South African coal industry experienced a series of methane explosions in which well over 200 coal miners lost their lives. In addition, a fire and an explosion in the gold mining sector claimed a further 240 lives. These tragic incidents resulted in the establishment of a research facility at Kloppersbos dedicated to explosion and fires research and the funding of an extensive research program, and almost certainly influenced the government of the day in its decision to establish, in 1993, the Leon Commission of Enquiry into Mine Health and Safety. The results of this focused research program, the wide-ranging recommendations of the Leon Commission and the determination of the coal mining industry to improve its safety record all combined to result in the past 20 years without a major explosion.This paper lists some of the research outcomes and, through three case studies, illustrates what can be learnt from investigations following explosions. The paper concludes with an evaluation of some of the findings of the Royal Commission on the Pike River coal tragedy. Many of the Commission’s conclusions are pertinent and relevant to the coal mining industry worldwide and their implementation could significantly improve coalmine safety; however, a careful study of the available facts indicates there could well be an alternative explanation of the source of the methane, the location of the ignition and the size of the explosion at the Pike River coalmine.CITATION:Phillips, H R, 2015. Lessons learnt from mine explosions, in Proceedings The Australian Mine Ventilation Conference, pp 19–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015