Search Documents

By M Medina, J Alexander, R J. Longey

Capricorn Copper Pty Ltd (CCPL) are operating the Capricorn Copper Mine located at Gunpowder, Queensland. As current holder of the environmental authority for the site, CCPL have obligations to rehabilitate areas of the mine that are no longer operational and have the potential to cause/contribute to environmental harm. CCPL sought a voluntary Transitional Environmental Program (TEP) to provide an agreed program of works to cap and rehabilitate the former Mammoth Tailings Storage Facility. The voluntary TEP contained conditions that were required to be met, to reduce the potential for environmental harm from the facility. The former Mammoth Tailings Storage Facility commenced use in the early 1970’s, and is an unlined valley in-fill structure, contemporary in design compared with other such approved structures of the era. The decommissioned Mammoth Tailings Storage Facility, now known as the Old Tailings Storage Facility (Old TSF), has been a legacy source of contamination due to the existing capping not meeting modern cover criterion, and allowing oxidisation and infiltration to the underlying acid forming tailings resulting in Acid and Metalliferous Drainage (AMD) from the facility. A cover design for the Old TSF, and other mine waste storages onsite that required clay capping, had been proposed by previous operators. Under the TEP cover design phase, it was identified that a key constraint was the lack of significant quantities of low permeability clay onsite. The lack of available clay prompted the consideration of alternate lining materials for the Old TSF, with a Bituminous Geomembrane Liner (BGM) being adopted as the preferred alternative. The BGM compared favourably with clay-based materials on seepage analysis, and led to other benefits by eliminating the need for borrowing clay off site, reducing the site’s environmental footprint, and reducing construction time. The BGM cover system on the Old TSF is being monitored with the intent to use this as a case study to confirm expected performance, enabling the cover design to potentially be adopted on the remainder of the site’s mine waste storages that require capping.

Jul 1, 2021

By H S. Welideniya, K Ekanayake

Carbon rich graphite deposits found in Sri Lanka are of inorganic origin and they occur as narrow steeply dipping veins. The vein width of these deposits varies from a few centimetres to metres, with an average vein thickness of 1 m. It is believed that the carbon rich fluid intruded into fracture zones under high pressure and the temperature has crystallised into graphite. This process has also generated many minuscule graphite veins centred on main mineralisation, which has reduced the host rock overall rock mass rating. These discontinuities could also be considered as joints with graphite infill. Graphite mining at Bogala Mines, Sri Lanka is a unique example of narrow vein mining faced with numerous wall stability issues resulting from weak graphite infilled joints.The Bogala vein type graphite orebody has an average vein width of 1 m. Overhand cut-and-fill mining method is used for stoping. The stope consists of two boundary winzes for material handling, access and ventilation. Mining is done on the strike of the vein and the average mining slice height is 2 m. A void to the height of one mined slice is left below the mining level during mining. Waste rock resulting from vein blasting and mine development is dropped into this void as fill rock. Any void height left greater than a single slice height will increase stresses in the stoping zone. This will increase formation of rock blocks and their effective separation from wall rocks. Split miniscule veins occurring around main mineralisation intensifies rock block formation in an environment of mining induced stress release. Consequently, any rock blocks sliding into stopes on graphite infilled joints will behave under constant normal stiffness (CNS) conditions and their shear strength will converge rapidly towards remoulded shear strength of graphite alone. Unlike with general infill deposited in joints, graphite has a very low friction angle and with its slippery nature, a small thickness may affect in great deal to reduce joint shear strength.In addition to immediate filling of excavated voids, controlled vein blasting and spot bolting have improved mine safety. Furthermore, rock bolts connected to each other through iron plates and anchored to anchor bolts installed in non-fractured solid rock are practiced to stabilise rock falls and wedge failures in narrow vein graphite mining. These practices have significantly contributed to safe mining without any rock bursts and catastrophic failures.CITATION:Welideniya, H S and Ekanayake, K, 2012. Challenges faced by narrow vein graphite mining and influence of graphite infill on wall stability, in Proceedings Narrow Vein Mining 2012 , pp 71-76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By S Logan, J Pu, J Milsom, G McDonald

Management of environmental issues is an integral part of the mine decommissioning process. In Queensland, miners must comply with environmental aspects of the Mineral Resources Act and Contaminated Land legislation. Successful decommissioning involves the integration of a final Plan of Operations, decommissioning report addressing the mineÆs commitments included in its Environmental Management Overview Strategy (EMOS), and Site Contamination Report for relinquishment of leases under the Contaminated Land Act (1991). Niugini MiningÆs Red Dome Mine is proceeding through the decommissioning process. This paper discusses the important environmental management issues including sampling programs, management of culturally significant areas, assessment of background concentrations of target analytes, the use of historical reviews and risk assessment techniques, the timing of works, and the remediation/management of large areas of impacted land. The importance of a clear communications plan between key stakeholders is also discussed.

Jan 1, 1998

By M Badawi, Y Foucaud, C Veloso, J Laine, A C. Araujo

Iron is one of the most exchanged commodities worldwide. Its use for steelmaking explains the growing demand in the metal which remains mainly produced by the mining and the beneficiation of iron ores. Flotation is the most used mineral separation technique worldwide, processing several billion tonnes (Bt) of ore annually, including, in some cases, hematite and magnetite ores. Based on the physicalchemical properties of mineral surfaces, flotation aims to selectively adsorb molecules that render mineral surfaces either hydrophobic or hydrophilic, known as collectors and depressants, respectively. Hydrophobic particles are then recovered in the froth by the injection of gas bubbles travelling up in the cell and attaching the hydrophobic particles. However, despite the popularity and the good performances of flotation, mining industry faces new challenges of decreasing grades and increased mineralogical complexness in ores. Many flotation variables, especially when related to reagent adsorption, remain poorly understood and it becomes necessary to gain knowledge to enhance the existing processes. Molecular modelling techniques like the density functional theory or molecular dynamics simulations (ie Classical molecular dynamics or Ab initio Molecular Dynamics) currently represent powerful tools for different applications in material sciences, like catalysis or depollution purposes. They have recently been successfully applied in the flotation area, with an increasing number of publications dealing with this topic every year. These tools provide crucial information on bulk and surface properties as well as on the adsorption mechanisms of reagents on mineral surfaces, key step in the flotation process, and synergetic effect of collector mixtures. A better understanding of the adsorption mechanisms of flotation reagents, provided by molecular simulations, will help to finely choose flotation reagents, and even lead to the development of new reagents formulations. Overall, these tools enable the discovery of practical and industrial solutions to improve the flotation process, which will undoubtedly help the mining industry to face its future challenges.

Nov 8, 2021

By F K. Altuntov

The study presented in this paper is based on the Kiirunavaara underground mine located in the northern part of Sweden. The deposit is mined using the sublevel caving (SLC) mining method. This paper briefly reviews the alternative SLC layouts, as well as presents challenges for the application. In Kiirunavaara currently, the traditional SLC design is employed, however, continuous improvement of material transportation systems used in mines generates a need for investigation of the current and future production area layouts in sublevel caving mines. When identifying the potential benefits of the alternative production area layouts, the production targets and effects must be further investigated to understand the benefits and potential effects. In this study, several different layouts have been investigated and evaluated. The designs include different development configurations and orepass infrastructure moved further away from the orebody and still require further investigation.

Mar 29, 2023

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

By C Muñoz, N Ortega, J Vergara, D Avilés

Mass blasts have been the subject of extensive studies because of their potential benefits in mining operations. However, it has not been possible to advance due to the paradigm that states that the blasts near the designed final wall or to critical structures have to be low tonnage. Another reason is the absence of specialised simulation programs to more precisely determine the influence of the energy released by blasting to the rock mass. There are some studies that demonstrate the possibility of massive blasting that maintain the design of the final slope (Farias and Santander, 2014). It should be noted that these studies develop the concept that the size of the blast should not increase the peak vibration in the rock mass.The study was carried out in partnership with Los Colorados Mining Company. Analysis, reconciliation and wall control for two types of blasts were performed:blasting production: approximately 850 000 t, with special wall control considerationsblasting of approximately 950 000 t over the entire width of the bench.Monitoring systems were used in the near field and far field using examination of holes in order to obtain information to assess the impact on the rock mass and then to compare these to conventional blasting combining production and contour blasting.The results show that for a large blasted volume, production and/or those generated from toe to crest on the bench did not produce more impact in the rock mass than the conventional blasting.The conclusions drawn from this study are:an improvement in the excavation rate of 7500 t/h that is higher than the maximum rates normally obtainedthe peak vibrations of the P wave generated by both blasts did not exceed the peak particle velocity criteria (Vergara and Muñoz, 2014)holes examination indicating no difference in their entire length, in pre- and post-blast reviewover US$2 000 000 savings generated in the year (estimated by the client) (Avilés, 2014).CITATION:Vergara, J, Muñoz, C, Ortega, N and Avilés, D, 2015. Benefits related to applications of a mass blast in open cut mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 625–632 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R A. Medower

This paper provides a glimpse into the future of minerals processing with emphasis on æAutomation InnovationsÆ for the new millennium, particularly those involving advanced process control and innovative new applications of process control technology in 2007.

Jan 1, 2000

The key issue which determines the use of imaging for explosives and mining research is the question - `What information will I gain by using imaging technology?' This paper will address that question from the point of view of a researcher and cameraman working in industrial imaging and photography. The paper will establish a common set of reference standards for high speed imaging and photography which researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of explosives and mining analysis and research. Further to this, the paper will examine the different technologies from an image quality reference point, ease of operation, cost, and reliability parameters. Finally this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of research and analysis in the explosives and mining industries. This will include a novel approach to high speed filming and analysis in the field which should deliver high quality images in a time frame which is more appropriate to urgent action and solutions.

Jan 1, 1995

By B Wentzinger, Y Keulemans

This paper presents the results of a field study designed to assess the impact of vane rotation speed on the estimated undrained strength for two Australian bauxite tailings storage facilities. The vane test results are assessed against cone penetration and dissipation tests results to identify if partial drainage may be an issue. An innovative tool capable of measuring pore pressures during vane shear testing, the Piezovane™, is introduced as an improvement over the standard field vane to assess drainage conditions in real-time.

Jul 1, 2021

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The Savage River open cut magnetite mine is located in rugged terrain in densely rain forested northwest Tasmania. The mine and concentrating plant are both in the Savage River valley. Pickand Mather Incorporated (PMI) operated Savage River as an open cut magnetite mine between 1966 and 1996. Acid rock drainage (ARD) was first noted in the last ten years of the operation, leading to elevated concentrations of heavy metals downstream of the mine. When operations ceased in 1996, PMI returned the mine to the Tasmanian Government along with a remediation fund of $11.4 million. At that time, the assessed cost of remediation was in excess of $120 million. As a result of the ongoing ARD contamination and to facilitate both a new operation and effective remediation, Goldamere Pty Ltd negotiated an agreement with the Tasmanian Government in 1996, which resulted in the Goldamere Act and the Goldamere Agreement. The agreement has allowed Australian Bulk Minerals (ABM) to remediate the Savage River mine in conjunction with the Tasmanian Government while re-invigorating a previously closed mine by providing ABM with an indemnity against past pollution. ABM can configure its mine and waste planning activities to maximise remediation benefits without fear of future litigation for past mistakes. The effect to date has been the development of a long-term strategy to remediate the Savage River and short-term remediation works such as water management, which provide benefits to the ecosystem. After five years, the Savage River is no longer significantly impacted by ARD for 30 kilometres downstream and trout are now reported within the reaches of the mining lease. The arrangements between ABM and the Tasmanian Government are an example of a genuine WIN WIN situation where co-operative environmental management of the site results in significant improvements and where the æregulatorÆ and the æminerÆ are working together to achieve mutually beneficial goals. The end result is a significant benefit to Tasmania.

Jan 1, 2003

By J J. Laas, A J. S Spearing

Considering the capital outlay, running costs and inherent difficulties of backfilling operations at depth the benefits need to be clearly established, quantified and then exploited. Expansion of Vaal Reefs Exploration and Mining Company towards even deeper, highly faulted ground, and the process of establishing codes of practice for the management of rockfalls and rockbursts, required that a sound support strategy be formulated. This paper describes the derivation of an overall backfilling strategy on Vaal Reefs. Use was made of experience gained over some 12 years with backfilling. Numerical modelling was used to estimate potential benefits of backfilling the deepest mining areas still to be extracted. In exploiting a probably unique opportunity, two contiguous mining areas bounded by the same major geological structures, were compared. One was extensively backfilled and the other not at all. Shaft sinking through a backfilled stope added another dimension to the database.

Jan 1, 1998

By P Esteves, J L. Bechir, R Galery, C Senna, V Souto

The current moment experienced by the mineral industry is marked by a series of economic, social and environmental challenges. Among the main challenges, it is important to highlight the decreasing in ore grades with the gradual depletion of the existing deposits, the high volatility in international commodity prices and the operational inefficiencies in the mine, beneficiation, and metallurgical plants. In this context, mining companies are continuously looking for alternatives that minimize production costs and maximize overall production. In addition, recent tragedies involving tailings dam collapses in Brazil, reinforced the need for a more responsible, sustainable, and conscious mining, such as aiming the preservation and rehabilitation of the land environment. In this scenario, the Sensor-Based Sorting (SBS) technology is currently getting more space into the mining market. This separation technology aims the removal of gangue material in coarse particle size fractions, prior to comminution and concentration stages. As a consequence, the technology allows a smaller consumption of energy, water, chemical reagents and other inputs. Moreover, the sensor-based sorting is a dry processing technology and favors the reduction of fine material to be sent to the tailings. The aim of this paper is to provide information regarding the technical and economical evaluation of SBS technology applicability to a zinc silicate mining in Brazil. The project evaluation was performed in two stages: laboratory test work and the execution of a pilot plant. The execution of a pilot plant allowed the technology optimization, quantification of downstream process effects, such as a proper economic evaluation about the technology benefits. Keywords: Sensor-Based Sorting; Particle Sorting; Ore Sorting; Preconcentration; capital expenditure (CAPEX); operating expenditure (OPEX); zinc; comminution; dry processing.

Nov 10, 2020

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Laas JJ, Spearing AJS

Considering the capital outlay, running costs and inherent difficulties of backfilling operations at depth the benefits need to be clearly established, quantified and then exploited. Expansion of Vaal Reefs Exploration and Mining Company towards even deeper, highly faulted ground, and the process of establishing codes of practice for the management of rockfalls and rockbursts, required that a sound support strategy be formulated. This paper describes the derivation of an overall backfilling strategy on Vaal Reefs. Use was made of experience gained over some 12 years with backfilling. Numerical modelling was used to estimate potential benefits of backfilling the deepest mining areas still to be extracted. In exploiting a probably unique opportunity, two contiguous mining areas bounded by the same major geological structures, were compared. One was extensively backfilled and the other not at all. Shaft sinking through a backfilled stope added another dimension to the database. Backfilling was introduced in 1985 and several potential spin-offs were expected. These included improved local strata control for fall of ground and rockburst conditions, regional benefits in rock mass stability and mine ventilation optimisation.

Jan 1, 1998

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

I was delighted to be invited to be patron of this Joint Conference, but the challenging task you have set yourselves, and your speakers' depth of expertise, deny anyone, even the patron, the opportunity to be patronizing. Australia's history has been inextricably link- ed with the fortunes of our great mining industry. That link will remain. Just as the gold rushes of the last century, and the discoveries at Kalgoorlie and Broken Hill changed the lives of generations, so the more recent development activity in iron ore, bauxite, nickel, coal, and uranium are having a significant impact on the lives of Australians today. The minerals industry has contributed to Aust- ralia's jobs and prosperity. Mining is not free of problems, but so long as safeguards are strong and appropriate the net benefits the mining in- dustry brings Australia will continue to be enor- mous. We rely on our mining industry to find, prove, develop and sell our minerals profitably, and my Government is committed to maintaining a healthy mining industry.

Jan 1, 1978