Search Documents

By R Kroukamp, G Rech

CRONIMET Australia in cooperation with Speciality Metals International, the mining lease holder of the Mt Carbine Tungsten mine, have demonstrated the preconcentration and processing of large (>12 million tonnes) tailings and mine waste dumps on site in far north Queensland. The first stage of this project has proven the economic viability of preconcentration using sensor-based particle sorting whilst ensuring high recovery of industry critical tungsten minerals – wolframite and scheelite. Sensor-based sorting technology have enabled the production of a sorter product to feed the existing wet gravity plant ensuring higher recoveries and increasing concentrate production. Processing of 1,000 tonne low grade samples using the TOMRA x-ray transmission (XRT) ore sorter installed on site, has reduced the volume of material entering the downstream wet processing plant by up to 60%. The sorted 10-25mm size range produced the highest upgrade ratio (product/feed) of 24:1 and achieved sorter concentrate grade of 1.52% WO3, sorter waste grades below 0.014% WO3 and metal recoveries of up to 93.4%. The appropriately sized, barren sorter waste material is also sold as aggregate and other quarrying products and thus adding to the overall economic benefit of the project. The utilisation of the sorting technology on site has produced an economically viable project, significantly reduced capital cost, and reduced the time to market of the final tungsten concentrate. The next phase of the project includes design and installation of a larger two sorter plant capable of over 150t/h feedrate.

Nov 10, 2020

By C Bie, S Li, P Xiao, P Zhao, H Lin

"Based on solid simulation material research, the simulation conditions for methane and coal solid-gas coupling were obtained using solid-fluid coupling theory. Using sand as the aggregate and paraffin and oil as the cementing agents, a material suitable for solid-gas coupling simulation was developed. A permeability testing instrument was also developed, and the compressive strength, brittleness parameters and seepage velocity of material were tested with different aggregates. The results showed that as the paraffin content increased, the compressive strength of the material increased but the permeability decreased. The oil removed the drawback of intensely changing material compressive strength. By setting a different ratio of aggregate to cementing agent, it can simulate rocks with different strengths and permeability. Applying the material to a mining simulation experiment revealed a relationship between methane seepage velocity and overlying strata movement. By extracting pressure relief gas from Shanxi Tianchi coalmine drainage, the authors found that the mining fissure zone was a storage area of pressure relief gas, and a gas drainage system can be placed to achieve good results. CITATION: Li, S, Zhao, P, Lin, H, Bie, C, Pan, H and Xiao, P, 2015. Character of simulation material of coal – rock and gas solid-gas coupling and engineering application, in Proceedings The Australian Mine Ventilation Conference, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By G Lumley

Gold miners have been underperforming the price of gold for a number of years. So why has the æmarketÆ undervalued our gold miners relative to what they have been mining? The low valuation ascribed to gold mining companies is largely attributable to their profit performance. In the period since 2006 the price of gold in A$ has risen about $900/oz, but the real cash margin (operating cash costs + cost of finding and/or acquiring deposits + the cost of bringing them into production) has only risen about A$100. Rising operating costs are a major part of this reduction in real margin. Energy and labour costs have risen more than the inflation rates across a number of countries as have taxes, royalties, etc. There are however, more significant contributors to the rising cost base. Firstly, in 2006 the average gold grade was 2.0 g/t; today it is 1.3 g/t. Secondly, strip ratios (for surface mines) have increased by 19 per cent during this time. Open cut mining equipment unit output across the world has dropped by 26 per cent during 2006 - 2012. Finally, costs have risen by 55 per cent during this time period. Consequently, there is now 3.8 times more mining cost required to produce an ounce of gold from surface mines compared with 2006. The decline in gold grade looks to be a permanent trend as does increasing strip ratio if output is to be maintained. Costs will continue to rise although cost control will be necessary. Reversing the decline in equipment performance and closing the gap between median and best practice provides the hope for a sustainable reversal of cost increases. The current gap between best practice and median performance has grown to 112 per cent for mining trucks, 168 per cent for excavators and 169 per cent for front end loaders. Closing this gap is the potential for a more profitable future. For most gold mining companies improving mining efficiency is not an option; it is an imperative.CITATION:Lumley, G, 2013. How many gold mines will inefficiency kill?, in Proceedings World Gold 2013 , pp 267-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Holtham, K Duffy, B, W Valery, E Tabosa, rade

Pre-concentration has potential to significantly improve Mineral Resource efficiency by removing gangue early in the process, before energy intensive and expensive comminution and fine processing. However, there are numerous options for pre-concentration and the performance and benefits of these are very case specific. To determine the best option for a particular deposit and to successfully integrate it into the overall mining and processing operations requires comprehensive evaluation. This needs to consider orebody suitability, technology capability and economic viability. The in-situ variability of a deposit and how it is influenced by mining methods and the liberation size of gangue are key factors which are generally not well understood. Geostatistical methods provide an insight into orebody variability, and the overall selection of any pre-concentration solution must be an integrated approach between geology, mining and processing. Many pre-concentration evaluations investigate the potential of just one option. Technology selection should start wide and may include: selective mining, pre-screening (with or without selective blasting), sorting (bulk and or particle), coarse gravity separation (e.g. jigging, DMS), coarse particle flotation, magnetic separation, etc. The upgrade performance of these processes is very ore specific and should be determined from testing, with detailed multi-component modelling used to determine the overall process performance. Many of these pre-concentration processes require significant ancillary equipment, feed preparation and materials handling. It is important to realistically estimate all costs to understand overall economics and select the best option. Some examples showing evaluation and comparison of pre-concentration options are presented in this paper. These include assessments of in-situ variability using geostatistical tools, process modelling of pre-concentration options and overall performance, preliminary layouts and cost estimates, and economic evaluations.

Nov 10, 2020

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By M Hedley

Tracking plant and personnel in underground environments provides multiple potential benefits for a mine including increasing safety, better monitoring of production, traffic control, and in the future monitoring and control of autonomous vehicles. The main techniques for wireless tracking are to use radio frequency identification (RFID), signal strength based techniques, and time of arrival (TOA) based techniques. RFID does not provide continuous tracking and signal strength techniques have poor accuracy in the complex radio propagation environment present in mines. TOA based techniques are potentially the most accurate, but most current equipment does not realise the potential of the technique. CSIRO has been developing the wireless ad-hoc system for positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines. WASP has been licensed for sporting applications and has delivered encouraging results in early trials for a surface and an underground mining application. The system utilises a number of ‘anchor nodes’ that are placed at surveyed fixed locations within the mine, and tags attached to plant or personnel to be tracked. The system provides an ad hoc data communication network, thus wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging from 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of initial testing in an underground mine that shows that the system achieves high ranging accuracy, hence localisation accuracy.

Mar 21, 2011

By I M. Platten, C J. S Sangster, Y Xie, S C. Dominy

Cononish is a steep, narrow NE-SW trending vein system that was emplaced into late Proterozoic metasediments. It shows brittle style deformation and postdates metamorphism and associated Caledonian foliations. The ore shoots plunge 45¦SW, have a 40 to 80?m intersection with the existing underground development and extend between 40 and 260?m down plunge. Small-scale sulfide-bearing domains within the vein carry the highest gold grades. They collectively define the ore shoots, where one or two and rarely three of the domains are present at an individual site in the vein. Gold occurs as electrum, with minor native gold. Silver occurs additionally as tellurides and native metal. The gold/electrum is fine-grained, generally <100?¦m in size and locally clusters. Visible gold up to 2000?¦m in size is rare. Gold and silver are generally spatially associated with sulfides in quartz. The main sulfide is pyrite, but galena, chalcopyrite and sphalerite occur also. Electrum and gold occur with galena in pyrite-hosted fractures. Gold is also associated with the contacts between galena and pyrite grains. Discontinuity of individual domains, variation in domain thickness and internal heterogeneity results in short scale variation in grade across the structure. Over 16?km of diamond drilling and a 1.2?km exploration adit has provided data to support a Mineral Resource estimate of 169?000?oz Au and 631?000?oz Ag reported in accordance with the 2004 JORC Code.CITATION:Dominy, S C, Platten, I M, Xie, Y and Sangster, C J S, 2013. Gold-silver vein mineralisation at Cononish, Scotland, in Proceedings World Gold 2013 , pp 445-454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By F M. Weir, M Fowler

The design of excavations in rock must, implicitly or explicitly take into consideration the influence of small- and large-scale geological structures. For most sites the complexity of a fractured rock mass is best captured using a 3D fracture system model based on field data. A discrete fracture network (DFN) approach involves stochastic modelling of the ‘smaller scale’, nondeterministic structures. For slope stability or tunnelling projects DFN modelling provides a valuable geotechnical tool for characterisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of the DFN modelling undertaken for the design of a large open pit in Australia. The proposed pit is to encounter a 160?m thick, high strength, sheared shale unit, which overlies a crystalline basement. DFN modelling was undertaken separately for both the shale and basement units. While the model inputs and development for each unit are briefly presented, the focus of this paper is on the various applications of the DFN modelling.A key advantage of the DFN approach for design studies is its probabilistic application to structural analyses and results. Multiple realisations of the same model were generated for both the shale and basement units, with the stability analysis carried out on each iteration. The generation of a large number of DFN models and analyses allow assessment of wedge volume, factor of safety and proportion of unstable slope for a range of conditions. The DFN modelling at the case study site was also utilised for a number of other purposes. For example, investigation of likely fault lengths in the shale unit and combined rock mass and defect failure. The development of this tool has been influential in improving our understanding of fracture networks for excavation design.CITATION:Weir, F M and Fowler, M, 2014. Rock mass characterisation and analysis for excavation design – a discrete fracture network approach, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 445–456 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By Y Xu, T Rowles, B Dareeju, A Dissanayake

Recent updates on tailings dam design guidelines require analysis of undrained (short-term) stability with the application of the SHANSEP model. The SHANSEP model, which was originally developed for alluvial soils, predicates that the Undrained Shear Strength (Su) increases with increasing effective stress. Residual soils by their nature do not necessarily follow this relationship. This paper examines an alternate method to define Su over a range of effective stress conditions for residual soils. Residual soils, formed by weathering of their parent rocks, are generally micro-structured in nature. The microstructural features, such as interparticle bonding, play a fundamental role in stress-strain behaviour of the residual soils. As interparticle bonding is independent of effective stress and void ratio, the undrained shear strength of residual soils is expected to be less dependent on effective stress than alluvial soils, especially at low stress levels. A series of triaxial tests conducted on residual soils, however, indicated that the undrained shear strength and the undrained shear strength ratio (Su/σv’) are to a degree dependant on effective stress. It was found that the undrained shear strength ratio is significantly higher under low stress levels and progressively reduces with increasing effective stress. Based on the laboratory testing data, a strength function with varying undrained shear strength ratios can be developed for the residual soils under the stress range anticipated for a design of a tailings dam. This includes capping the input undrained strength at lower effective stresses based on the drained (effective) and minimum undrained strength. The Factor of Safety (FOS) calculated for the embankment utilising the traditional limit equilibrium (LE) method indicated the application of undrained strength function for the residual soils can provide a significant optimisation for the embankment design compared to adopting a constant undrained shear strength ratio or constant undrained shear strength in the design.

Jul 1, 2021

By C Cavern, G Jacobs, F Durufle, L Ameglio

Airborne geophysics and geomatics is at a crossroads as to whether it remains a viable mapping tool, both technically and commercially, and broadens its potential for new applications (eg environmental monitoring, civil engineering and precision farming). The use of small and stable multisensor aerial platforms to conduct highly flexible surveys flown at a low/reasonable cost of operation is a recurrent wish of many stakeholders in the natural resources exploration and mining industry. Through its Fly Light Airborne Geophysics research program, EXIGE and partners have pushed the development and testing of two new airborne carriers with unique capabilities for geo-surveys: GyroLAG’s gyrocopter and Infotron’s unmanned aerial vehicle (UAV). These carriers are the next generation of versatile and innovative aerial vehicles for remote sensing and monitoring. They are rotary, smart tailored, ultra-high resolution manned (gyrocopter) or autonomous (UAV) airborne platforms that combine the merits of dense data sampling, accurate position location, very low clearance above ground or sea level, slow speed, interchangeable and combined multiple geo-sensors, automatic data quality control and real-time quality assurance. They also have the benefits of being highly efficient, cost-effective, commercially attractive, safe, reliable and easy to deploy and operate. Their technical specifications and multiple advantages compared to traditional aircraft and/or ground crews are presented in this paper. An overview of various geo-sensors (magnetic, gamma-spectrometry, visual, near-infrared and LiDAR) carried on-board is also provided.CITATION:Ameglio, L, Durufle, F, Jacobs, G and Cavern, C, 2015. Light airborne platforms for monitoring mines and minerals, in Proceedings Third International Future Mining Conference, pp 11–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By G Neely

COPING WITH COMPLEXITY In every industry, and mining is no exception, plant and processes increase in complexity over time and managers and operators need correspondingly more knowledge. The mine manager has to delegate details to operators, engineers, metallurgists, accountants, safety specialists, personnel officers and the rest. Is it reasonable then, to expect the Mines Inspector to be competent to judge the conduct of all these operations against the criterion of the regulations? Obviously not, but what are the alternatives? One is a superficial inspection where the inspector goes on a hazard hunt for broken steps and missing handrails. Another is one in which an army of specialist inspectors marches on a mine, sometimes outnumbering the staff. Each is competent to assess some part of the operation and if he or she can find an opposite number among the mine staff, they can discuss details. But what good does it achieve? The system acts to remedy present defects and to make recommendations which, if only they were followed, would prevent the same things happening again. Given that this process has been going on since the first Factory Act of about 1840, how is it that there are any more defects left to put right? The answer of course is that defects keep appearing, and new defects arise as fast as the old ones are found and corrected. Further progress can only be made by preventing defects at their source.

Jan 1, 1994

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

At Cliffs Natural Resources Ltd (CNR) crushing and shipping sample stations, precisions are estimated for the sampling, preparation and measurement stages of iron ore sampling in accordance with ISO 3085 (2002). In this Standard, gross duplicate samples are prepared at each of the three stages, yielding eight measurement assays. Appropriate calculations of the differences between assay pairs are then made to estimate precision of each stage of sampling. The International Standard for checking precision in iron ore sampling, ISO 3085 (2002) prescribes a method for identifying outliers that is ambiguous and possibly inappropriate. The procedure also makes an unnecessary implicit assumption, that the differences between assay pairs are normally distributed. The Anderson-Darling statistic is used to demonstrate that in some cases the assay pair differences have distributions significantly different from normal. When applied at CNR as specified, the Standard leads to precision estimates well below the expected values, thus overestimating the sampling method's capability and limiting the opportunity for real process improvement. This paper suggests an improved method of estimating sampling, preparation and measurement precision. A bootstrap procedure is used to estimate confidence limits for the calculated precision estimates. The proposed method would be suitable for testing blasthole precision. The discussion is supported by extensive simulation modelling of realistic data.

Mar 1, 2010

By C Gormley, G Lane, J Kwak, A Hopkins

Complex processing plants present a myriad of safety issues to the design engineer. The extent to which the design engineer manages to lay the foundations for a safe plant ultimately sets the stage for life long safety performance. Industry traditionally measures engineering safety performance by indicators such as Lost Time Injuries, Restricted Work Case Injuries, Overall Incident Frequency Rates, etc. While these measures are useful indicators of performance for the construction, commissioning and operations phase of a project, they do not necessarily drive the most appropriate behaviours for Safe Plant Design. Achieving an inherently safe design requires a diligent focus on low frequency, high consequence events. First and foremost the engineering team needs to have a design culture and methodology which leads to a plant which is as close as possible to being inherently safe. Such a culture might come from an organisation that has æmindfulnessÆ about safety, and which is nurturing a culture where warning signs are recognised and addressed. This paper explores the development of mindfulness and warning signs in design.

Jan 1, 2004

Information obtained from a reconciliation system provides fundamental indicators to an operations performance and is often neglected as a key performance indicator when developing a business plan or mining schedule. The cycle of exploration, ore definition, mining and processing within a company is constantly scrutinised both internally and externally as to the safety, environmental and financial performance of these activities with the operators judged on their performance on a periodic basis. However, it is not unusual for the reconciliation process to be given scant attention until a serious issue (usually a shortfall) occurs, at which point short-term solutions may be implemented which only serve to compound the original problem. A robust reconciliation system takes time to develop and implement initially and must continue to evolve with time. The best systems are those where all the stakeholders in the ultimate outcome are involved in the design and accept responsibility for the validity of their component inputs. Output from the reconciliation process can be utilised to fine-tune all aspects of an operation once the underlying issues leading to a particular result are understood.

Jan 1, 2002

By D Lozada, A Salazar

Geometallurgy is a tool that, for more than a century, has been present in the implicit operations of mineral beneficiation. There’s a need to understand the characteristics of the material to be processed. This has led metallurgists to ask geologists what type of rock and mineralogy is entering the Beneficiation Plant and vice versa. The geologist needs to understand the beneficiation process in order to be able to carry out the production programming. The paradigm is whether geometallurgy can be applied to small-scale mining or if it is only aimed at large companies that invest millions of dollars to conduct studies. With this work, we provide an example of how geometallurgy can help improve the processes of a small mining company located in Ecuador (South America). We performed characterizations of geological and mineralogical and metallurgical tests in universities and the National Research Institute of Geological Metallurgical Mining. The origin of the theme is based on the fact that gold has been detected in the final tailings. The flotation concentrates meet the standards in terms of the content of economically profitable metals, but this isn’t the case with regards to the percentage of arsenic, which has hindered sales. The hypothesis is: conducting technical and scientific research will optimize the metallurgical process for the recovery of gold and concentrates. The referential framework is the mining geology of the Bella Rica District, current status of the Beneficiation Plant. In the theoretical framework there are parameters of the veins, comminution operations, gravimetric concentration, flotation, and cyanidation. The methodological framework contemplates the characterization of the gold ore, the chemical, mineralogical, textural, metallurgical analysis and the interpretation of the results. Thus, the design of a geometallurgy model of the deposit, with its main characteristics, is a conclusion that serves as a basis for the proposal of the optimization of the metallurgical process.CITATION:Lozada, D and Salazar, A, 2018. Geometallurgy applied to small-scale mining: a case study, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T GRAHAM-TAYLOR

A trend towards mining more complex and economically marginal orebodies, often combined with increasingly tight product specifications, increases the number of variables which need to be considered in production scheduling. Linear programming incorporating integer constraints can be used to create production schedules which are practical as well as mathematically optimum. Factors which can be taken into account include variability in product stockpiles, targets for head or product grades, production of different material types, production from different areas, production targets for loaders, and dependencies between mining blocks. For each schedule an appropriate objective for optimisation must be chosen. Examples of objectives are: to minimise or maximise grade variation; to minimise waste movement; and to minimise movement by front end loaders. A staged approach to the implementation of computer systems based on linear programming optimisation is Proposed.

Jan 1, 1992

By Szwedzicki T

In recent years substantial advances have been made in the field of geomechanics. Staff at the Western Australian School of Mines (WASM) are keen to see that such advances continue and that the mining industry in Australia can take full advantage of such developments in a timely manner. WASM views mining geomechanics in its broadest sense, as being concerned with the characterisation of the physical properties and the behaviour of earth materials (soil, rock and water) and openings as mining proceeds. Aspects such as, soil and rock improvement techniques for difficult site conditions and the rock breaking processes, are also considered to be an integral part of mining geomechanics. This paper indicates the inter-relationships between the various areas within the field of geomechanics and the strong reliance of all of these areas on site specific engineering geology.

Jan 1, 1992

By A Weston

Northparkes Mines is a joint venture between Rio Tinto and the Sumitomo group and is operated by Rio Tinto to produce copper concentrate from ore sourced from open cut and underground. Underground ore is mined with an owner operator workforce using the block cave method from the E26 deposit, with the first lift of the cave now completed. Development of the Lift 2 block cave commenced in March 2001 using a contract workforce. The Lift 2 Project required the mining of 14 700 m of decline and lateral development to establish a new mining horizon at the 9450 level and to develop two new conveyor declines. Also included in the scope was the excavation of a Crusher chamber to house the jaw-gyratory crusher. This paper describes the excavation of the hydroset chamber and orepass that sit immediately underneath the Lift 2 Crusher chamber. It includes risk assessment, planning, development of method statements and standard operating procedures, through to the excavation of the orepass and the installation of ground support in seismically active ground. There was a major ground failure in the backs of the conveyor feeder chamber during its excavation, which affected the excavation of the orepass due to its proximity to the breakthrough site.

Jan 1, 2005