Search Documents

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

By Magne L, Barria J, Castro O, Menacho J, Gonzalez GD

An extensive experimental campaign was developed in a continuous 6 x 2' (D x L) pilot scale SAG mill. The effect of the feed flow rate, feed solids concentration, ball filling fraction and feed size distribution, over the mill performance was investigated. The residence time distribution (RTD) for the fine material was measured in every test, in order to detect changes in the mixing characteristics of the mill under different operating conditions. Based on phenomenological considerations a state model of the SAG mill was developed, which independently incorporates mechanisms such as: grinding, mass transport and classification in the grate discharge. These can be parametrised using information and optimisation software. This comminution model extends the compensation condition, which is a conventional hypothesis for ball milling, to the semi-autogenous mill grinding. The mathematical analysis of this hypothesis, applied to SAG mills, allow the reduction of the number of parameters in the model, using the relationship Ki = (1-bii)Si, where b and S have the conventional meaning. Therefore, the distribution fracture matrix bij and the specific fracture rate SIE are grouped in just a single diagonal matrix Ki.

Jan 1, 1993

By D Suppel, Y Miezitis, S Jaireth

The competition between various options for the use of land is ever increasing. Commonly in Australia large tracts of land were un-encumbered by sweeping land use option limitations, but this situation has been rapidly altering in recent decades as governments are obliged to maximise the utility of the land for a broad range of competing interests. While the interests of miners have always been considered, the effects on limiting access to land for exploration and possible mining have not always been effectively incorporated into decision-making processes. As a result the challenge for national and state organisations representing these interests has been to develop a transparent process to allow for the mineral potential of an area to be systematically assessed and for information to be presented for use by specialists and non-specialists. Government agencies are called upon to implement government policy but also to provide accurate and meaningful advice which can assist in policy and land use decisions. Commonly timeframes are short and information can be less than complete. Nevertheless on-going decisions are made based upon the best available understanding. It is in this operational framework that the methods described in this paper are set. The paper describes a process for quickly and systematically providing advice on mineral potential for use by government agencies and ultimately the community within tight time and resource constraints. It is a method of combining the accumulated knowledge about mineral resources and their potential and presenting this information in an easily accessible form which can be used in a negotiation and policy development environment. Development of the method was undertaken to meet the needs of the Regional Forestry Agreement process in Australia. The method has been applied to study areas in New South Wales, Tasmania, Western Australia and elsewhere. Examples in this paper are taken from north eastern New South Wales.

Jan 1, 1999

By K Dagdelen, I Traore

This paper presents an iterative net present value (NPV) maximisation method to determine the optimum surface to underground transition depth for an orebody to be mined by multiple open pits and an underground mine. The determination of transition depth from open pit to underground mining is based on global production scheduling optimisation of open pit and underground mines using mixed integer linear programming. The method is applied to a case study coming from a gold mining complex with six open pits and a large underground mine using longhole open stoping. The results indicate potential improvements of the NPV of global operations when compared to the traditional techniques based on independently optimised open pit first, followed by underground mining.CITATION:Dagdelen, K and Traore, I, 2014. Open pit transition depth determination through global analysis of open pit and underground mine production scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 195–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By T Napier-Munn, E Louwrens, L Keeney

Geometallurgical characterisation of ore deposits is accepted practice in some parts of the mining industry today. Its primary aim is to provide constrained inputs that reflect inherent geological variability and its impact on metallurgical performance for the deposit. Geometallurgy improves project value because it suggests more valuable alternatives for scheduling and processing through an increased knowledge and understanding of the interactions of rock properties and extractive technologies. Lower project cost (both capital and processing) and improved recoveries are the result from closer tailoring of the mining and mineral processing strategies to the characteristics of the resource (Dunham, Vann and Coward, 2011). Tailings storage facilities (TSFs) can be seen as potential resources and it is argued that fundamental geometallurgical characterisation as applied in ore deposit characterisation should also be applied to planning the retreatment of TSFs. This paper will describe a research project at Julius Kruttschnitt Mineral Resource Centre assessing if geometallurgical principles and methodologies can successfully be applied to TSFs as they have been to primary deposits. The project is establishing a new standard method of tailings evaluation which will include a 3D spatial model of the tailings resource. Initial domaining of the TSFs was done using principal component analysis followed by k-means cluster analysis based on chemical assays from drill core samples. The subsequent characterisation of the drill core samples has involved chemical, mineralogical and metallurgical profiling, with a range of metallurgical tests being conducted on the samples. This characterisation step is followed by class-based analysis, predictive modelling and process performance domaining with the ultimate objective of establishing a 3D spatial model incorporating geochemical, mineralogical and metallurgical performance data. This approach, which takes into account processing performance permits a more realistic (as compared to doing limited chemical assays and metallurgical testing) economic evaluation of the potential of reprocessing the tailings material. It is believed that the approach is generic and can be applied to other TSFs being considered for reprocessing. The present case study has also established the gold, copper, magnetite and cobalt deportment for an iron oxide copper-gold deposit tailings resource.CITATION:Louwrens, E, Napier-Munn, T and Keeney, L, 2015. Geometallurgical characterisation of a tailings storage facility – a novel approach, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 125–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goiás and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m × 3.8 m to 2.0 m × 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m × 3.8 m to 2.6 m × 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Corbett GJ

The Bulolo Graben represents an intra-arc rift formed by activa- tion of transfer structures in an extensional setting formed be- tween the eastern and western sectors of the New Guinea Origin. Crustal thinning has facilitated the emplacement of dacitic Edie porphyry intrusions, locally as flow dome complexes, phreatomagmatic (diatreme) breccias and the Bulolo ignimbrite/ agglomerate as an extrusive equivalent of the Edie Porphyry. Gold mineralization is localized along intra-graben structures, com- monly at the intersection with cross structures and occurs in sub- sidiary dilational fractures and not the localizing major structures. Gradations are apparent in the styles of mineralization according to the degree of erosion of the hydrothermal system. Hamata occurs as the deepest mineralization of the quartz-sul- phide style Wau, Hidden Valley, and Edie Creek are dominated by carbonate-base metal styles. Kerimenge grades from quartz sulphide through carbonate-base metal to epithermal mineraliza- tion, the latter style also being present in the periphery of Edie Creek. Here, pre-existing fractures of the Edie Creek Structural Corridor have been reactivated by movement on NS structures to form the ore-hosting dilatant lodes. Fluid flow may have been from the vicinity of the Nauti diatreme margin and along the vein System.

Jan 1, 1997

By Rowe J

The case study is based on the largest ore deposit at Mt. Lyell; the Prince Lyell deposit, comprising a regular lensoid mass of dissemina- ted and vein pyrite-chalcopyrite mineralisation. Reserve estimation employs conventional techniques, based on diamond drill hole and relevant development sampling data. Probable ore reserves are estimated using the contouring (isoline) method an longitudinal projections for ore thickness and accumulation (m %Cu) at a '0.8% Cu' cutoff. Final stope and pillar res- erve estimates (proved ore) are derived from designed ring tonnages and contoured accumula- tion for individual mining units, following more intensive sampling. Systematic grade control procedures have been adopted and individual stopes and pillars reconciled against mill production. The proved ore estimates have been found to com- pare favourably with the reconciled production.

Jan 1, 1979

By S F. Wang, J J. Yin

Dust pollution poses a persistent challenge within mining processes, giving rise to a spectrum of concerns, including occupational diseases, mechanical degradation, diminished visibility, and the potential for dust explosion incidents. Existing dust detection and monitoring methodologies face limitations, including insufficient measurement accuracy and intricate processing procedures. Consequently, a comprehensive identification and evaluation system rooted in image processing technology is proposed to facilitate real-time measurements of dust pollution in mining worksites. The study primarily employs grey scale average and fractal dimensions to characterise particle features evident in collected dust images. As a result, the data processing platform can dynamically process data and present dust pollution conditions. Notably, this research integrates the monitoring and assessment of dust pollution with the systematic adjustment of mining parameters, ventilation parameters, and strategies for dust reduction. Through statistical analysis of dust concentration and particle size during mining processes, rock properties such as components and cuttability can inform mining parameters. This information, in turn, guides detailed excavation strategies, including cutterhead speeds, torque, and excavation speed. Similarly, analysing dust characteristics derived from images is a valuable resource for gaining deeper insights into the efficacy of implemented ventilation strategies. By harnessing vision-based information detailing dust concentration and distribution, a wealth of direct guidance becomes available for refining ventilation parameters. This encompasses crucial aspects such as the selection of appropriate ventilation systems tailored to the specific mining environment and the optimisation of operational conditions for ventilation fans. Additionally, the detailed information derived from the visual data allows for strategic decisions on factors like the spatial arrangement of ventilation outlets and the calibration of airflow rates. Moreover, precise choices for dust reduction measures and parameters can be made based on the prevailing dust conditions. Upon real-time monitoring of dust pollution using the proposed method, corresponding measures such as spraying and foaming can be promptly implemented. Crucial parameters, such as spray angles and volume, are integral to these application processes. In essence, the proposed method assumes a pivotal role in not only dust monitoring but also the formulation of preventative and control measures within mining processes.

Sep 1, 2024

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By V Rasouli, G Cavanough, A Mokaramian

The sampling time, the costs and its quality are the three factors that determine the best method of drilling in mineral exploration. The two principal methods of reverse circulation (RC) and diamond core drilling are often used in combination by mine operators. RC is used for drilling shallow holes and in-pit grade control, and core drilling for deeper holes to identify future resources. The RC method is faster and more flexible than coring and provides virtually uncontaminated cuttings (ranges from dust to 25 mm chips) to the surface cyclone suitable for geochemical anomalies. The diamond coring produces core samples to increase the level of geological knowledge and the 3D extension and distribution of the orebody. However, both of these methods are subjected to certain limitations and inefficiencies in reaching deeper depths and drilling complex hole geometries. Examples of such shortcomings include the inability to provide enough air pressure for RC drilling and high friction between drill pipe and the hole wall in diamond core drilling.Considering that delivering large volume of reliable samples from deep zones to the surface in shortest possible time is of paramount importance in mineral exploration, and assuming that obtaining core samples over whole overburden is not always essential, then drilling small size holes as fast as possible and delivering the small chip samples to the surface would be a good alternative with several advantages over conventional drilling methods for deep hard rocks mineral exploration. As a result, the use of coiled tube (CT) drilling technology has been proposed recently for such applications. CT is a continuous length of ductile steel or composite tube stored and transported on a large reel; and allows fast drilling by eliminating the connection time and providing continuous circulation during drilling. This enables quick access to the zone of interest to collect the cuttings or obtain core samples. CT is advantageous particularly in drilling directional boreholes and multi-laterals. In this paper, feasibility of using CT delivering reliable samples is discussed for deep mineral exploration. In addition, recent developments and practices are presented that make CT a reliable drilling technology to drill cheaper, faster and deeper and to deliver more continuous and reliable data and samples from deep formations.CITATION:Mokaramian, A, Rasouli, V and Cavanough, G, 2012. Quality sampling using coiled tubing drilling in deep mineral exploration, in Proceedings Sampling 2012 , pp 73-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Rayner J. G, Leckie J. F, Moorehead C. F

The Coronation Hill gold-platinum-palladium prospect is located in the valley of the South Alligator River (latitude 13'35'S, longitude 132'36'E), about 80 kilometres east of Pine Creek in the Northern Territory. Coronation Hill was one of thirteen sites in the South Alligator Valley at which uranium was mined between 1955 and 1964 after initial discovery by the Bureau of Mineral Resources in 1953. Most of the mines were operated by United Uranium No Liability. The Sleisbeck mine 25 kilometres south of Coronation Hill was operated by North Australian Uranium Corporation and the group of mines at Rockhole about 20 kilometres to the north-west of Coronation Hill was operated by South Alligator Uranium No Liability. The uranium mine at Coronation Hill produced about 26000 tonnes of ore averaging 2.6 kg/t U308 with an estimated average gold grade of 10.4 g/ gold. Gold was commonly associated with the uranium mineralisation and was recovered at the gravity treatment plant at El Sherana. Gold was also recovered in 1986 by Pacific Gold Mines Limited by treating the tailings from the Moline and Rockhole uranium leach plants at a CIP plant at Moline. With the completion of uranium contracts in 1964 mining in the South Alligator Valley ceased. Exploration for uranium continued in the area during the 1960s and 1970s with no success. The Coronation Hill Joint Venture (BHP Gold Mines Limited 45 per cent, Pioneer Minerals (Gold) Pry Ltd 45 per cent, Notgold Limited 10 per cent)carried out the first exploration specifically targetted at gold in 1984 with the drilling of five vertical drill holes which indicated high potential for a substantial gold resource at Coronation Hill with no associated uranium. The Joint Venture has sub- sequently drilled about 25000 metres of diamond drill holes at Coronation Hill alone. Analytical results from 1985 drilling established that platinum and palladium were associated with gold. An indicated resource of 3.49Mt at 5.12g/t Au, 0.21g/t Pt and 0.56g/t Pd has been calculated using a lg/t Au cut off.

Jan 1, 1991

By D Kent

"There has been a revolution occurring in underground mining over the last several years, where big headline items such as the Internet of Things (IoT), optimisation, managing data, data mining etc – the list of current catchphrases, goes on. In the end these are nothing new; but the ‘things’ (sensors) are becoming smaller, cheaper and easier to deploy, and the analysis much more powerful as computer processing speeds increase. However, to take advantage of the myriad of devices out there and gain the processing power to analyse and use the data, a reliable ‘conduit’ is needed for that information to be delivered where it can actually be used. That is, a high quality data network.Modern mining is like any other industry in the information age: the access to reliable data is the first, critical step in improving productivity (Stevens, 2015). The convergence of communications onto an IP (Internet Protocol) backbone has been the driving force in enabling the productivity gains in general industry over the last two decades.This paper overviews how this technology has developed as an enabler in accessing productivity and safety benefits, and how it has used access to large amounts of data to manage mining processes underground. Reams of data are useless, but with the reliable receipt, analysis, processing and feedback system in place to use that data, benefits can be realised.Automated mining systems are increasingly being seen as a key requirement for a productive mining operation, and the importance of an integrated communication network infrastructure to support such systems is growing. Another emerging driver is the much talked about IoT and data analytics, both dependant on reliable, accurate, high volume data.The author will outline how communication infrastructure is fundamental to the operation of such systems, and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation and other data hungry systems within the overall mine operation.Mining operations embarking down this road are discovering that the required network must be based on a true enterprise level architecture to, not only enable the mine’s current plans for remote or automated mining, but also to provide a scalable and integrated platform for future developments. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting, particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.How certain mining operations lay the necessary foundations to meet their current requirements, while supporting their visions for a more automated and proactively managed mine, will be explored.CITATION:Kent, D, 2017. Modern mining – why bandwidth matters, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 123–128 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By R D ROSENTHAL

BHP Iron Ore Ltd's Mt Whaleback is the largest single open-pit iron ore mine in the Pilbara region of Northwestern Western Australia. A division of BHP Minerals, one of three core businesses of Broken Hill Proprietary Company Ltd (BHP), BHP Iron Ore - Newman is a joint venture with minor participants C Itoh Minerals and Mitsui. Mine planning for Mt Whaleback generates detailed sequence plans for a long term forecast incorporating equipment requirements, marketing forecasts, and pit development strategy. Utilisation of several computer packages, both commercially available and site modified, are necessary to achieve such a demanding task.

Jan 1, 1992

The arbitration process, and its drawbacks: Any time you have taken part in a major arbitration, and the decision, when it comes out, is not what you thought it would be (which is bound to happen occasionally), the normal reaction is something like æthe arbitrator got it wrongÆ. Again normally, when you have cooled down a bit, and you look in more detail at the decision, you can see, probably, æwhere he got it wrongÆ (it is only male arbitrators who get it wrong). Ultimately, when reason prevails, and you reflect on it, you can see that what really happened was that you failed to get the arbitrator to see what you were getting at in the point or points concerned. This is doubly frustrating, when you consider what has been involved in getting to this point, having been through it all at least twice. An alternative to this process may be the dispute review board.

Jan 1, 1999

By P Hanna

Following the Busang fiasco, more detailed guidelines were appended to the latest revision of the JORC Code released in September 1999 (JORC, 1999). Although the definitions and terminology essentially remained unchanged, the additional information in the guidelines has highlighted a number of issues for consideration by geologists undertaking computer-based resource estimations. The three main issues are:Data Integrity û details such as drilling and logging techniques, sampling procedures, assay tests, site visits, data recording and aggregation methods need to be considered. Geological Interpretation û is the Competent Person applying the appropriate software interpretation to the deposit in accordance with the regional setting. Are the correct computer-based tools being applied and are they producing the desired result (without compromise) to the satisfaction of the Competent Person? Modelling Technique û the importance of the relevant experience of the Competent Person not only in regard to the geology, but also with respect to the modelling algorithms and resource calculation methods of the computer software system involved. At the end of the day, it is essential that the Competent Person undertake a reality check on the resource estimation itself. They should also check that the borehole spacing is in accordance with the level of continuity for each critical parameter (such as structure, grade, impurities, etc) for which the resources are categorised.

Jan 1, 2000

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

By DJ McKEE

Process control emerged in the mid-1960s as a new and exciting method of improving the performance of mineral processing operations. The early Australian developments, principally in Broken Hill and Mount Isa, were based on pioneering work in instrumentation, the availability of small digital computers and a particularly effective partnership between companies with technological foresight and University and CSIRO research groups. Initial progress was rapid and within ten years many plants were committed to process control. Process monitoring is now routine and most circuits have some level of control. However, few plants have comprehensive optimising control systems as the difficulty of developing control strategies which can cope with the wide variety of conditions encountered in most mineral plants has been fully appreciated. This paper summarises past experience and assesses the degree of application of different forms of process control in metallurgical plants. Barriers to the effective utilisation of opt rising control are identified and some suggestions for advancing the application of control are made.

Jan 1, 1992

Since the initial discovery of phosphate rock resources in North West Queensland in 1966, significant changes in ownership and development direction have occurred. Initially development of the resource involved beneficiation to produce a more saleable grade of phosphate rock. However more recently development has focused on the production of a high analysis fertilizer product on the minesite. These changes have been influenced by economics, industry/government cooperation and a changing phosphate industry.

Jan 1, 1998