Search Documents

By Grano S. R, Ralston J

It is the perennial problem most metallurgists face when examining data collected from laboratory float tests and plant surveys - there are more numbers than we know what to do with! The objective of this paper is to analyse and interpret a set

Jan 1, 1994

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

By M Hernan

Bendigo Mining Limited has established a modern underground gold mine and processing plant at Bendigo in central Victoria. The Bendigo goldfield produced around 22 000 000 oz of gold between 1851 and 1954. Approximately 4 000 000 oz were sourced from surface alluvial workings with the remaining 18 000 000 oz won from underground quartz reefs. The modern mine is accessed via the Swan Decline, which commences at the Kangaroo Flat site on the southern outskirts of Bendigo and progresses in a north easterly direction between the Deborah and Sheepshead anticlines, reaching a depth of almost 1000 m below the City of Bendigo. Development of this decline commenced in 1998. Since that time 20 km of underground development has been completed. Exploration drilling, on-reef development and bulk sampling carried out between 1999 and 2005 resulted in the estimation of a Probable Ore Reserve of 700 000 tonnes at 9.0 g/t gold for 207 000 oz of gold. These Ore Reserves were contained within four reefs located on the Deborah and Sheepshead anticlines. Reef mining commenced in late 2005 from the Shywolup and Greater Garrard reefs. Material mined was stockpiled on the surface in preparation for commissioning of the process plant which commenced in mid 2006. Mining and processing were carried out between August 2006 and May 2007 during which time 176 000 tonnes were processed at an average grade of 5.4 g/t gold to produce 26 735 oz of gold. Plant feed was sourced from four reefs. This paper discusses some of the issues which were encountered with the definition and mining of these geologically variable and nuggetty reefs. This paper covers exploration techniques, grade estimation, mine geological control, mining methods, geotechnical issues and reconciliations. It will also discuss some of the lessons learnt and how these will be applied to future Mineral Resource and Ore Reserve estimation, as well as underground operations.

Jan 1, 2008

By C Buchanan

For a long time there has been a known relationship between the northern Heavy Mineral (HM) deposits of the Murray Basin to the extensive north east trending ridges in the area. These ridges have been a targeting tool for exploration and have uncovered some significant discoveries, some of which have turned into mining projects. Bemax’s Ginkgo and Snapper deposits are good examples of how the faulting helped create an economic deposit but also result in significant planning issues in the exploitation of these deposits. Material balance, induration and pyrite issues have been made easier to manage through good geological understanding of the deposits.

Aug 22, 2011

By C A. Brannon, C A. Dipas, H A. Vega, D Villa

The development and construction of the Grasberg block cave mine (GBC) is in progress, currently targeting initiation of caving in late 2018. Current production planning anticipates ramping up to full production of 130 000 to 160 000 t/d by 2027. As GBC approaches the production phase, there is a high priority on increasing the accuracy and level of detail in the production plan. The advance of the cave front directly controls the drawbell opening rate that is achievable. Therefore, an essential component of this plan is to produce an undercutting and drawbell sequence that honours the caving parameters that have been set for the mining blocks by the GBC production planning team.The PT Freeport Indonesia (PTFI) mine planning team and the Geovia caving business unit have developed a computational tool (Undercut Tool) capable of generating an undercutting sequence that follows a set of caving rules, such as advance rate per tunnel, maximum blasted area per period, control of lead-lag and shape of the undercut face. This tool also produces a drawbell sequence that honours the undercutting advance sequence, which is ultimately used to generate a life-of-mine production plan. This paper describes the inputs and outputs of the Undercut Tool that have been used to compute the long-term production plan for the GBC mine. It will further describe how the Undercut Tool takes into account operational constraints and geotechnical considerations that must be considered when developing a defendable production plan. Included is a discussion of the initial results of the planning outcomes from the tool; it will demonstrate how this work will support specific aspects of the plan such as the detailed undercut production drill and blast plans for the drill ring sequence, as well as how that plan will drive the drawpoint opening plan.CITATION:Villa, D, Brannon, C A, Dipas, C A and Vega, H A, 2017. Integrated drawbell and undercut scheduling using a computational tool at the Grasberg block cave mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J Coombes

"In today’s challenging climate of reduced staffing, limited funding and uncertain markets, we are called on to operate more productively and ‘be more innovative’. As an industry, we are quick to identify our practice areas as a mark of our role in the machinery of the mine value chain. We proudly note our profession – ‘geologist’, ‘mining engineer’ or ‘accountant’ – and demarcate our responsibilities and even our physical space. We even subdivide our disciplines into sacred entities such as ‘logging geologist’, ‘resource geologist’ or ‘structural geologist’ to prevent any blurring as though somehow the confusion will cost valuable disciplinary ground. How can we function professionally to heed the call to be more productive and more innovative?The purpose of this paper is to underscore what is expected from project evaluation, examine the ways in which we work as an industry and explore alternatives used in other industries and environments.The paper begins with a summary of project evaluation expectations and the ways in which disciplines typically interconnect when conducting project evaluations. Next, the paper examines alternative work frameworks and making a distinction between multidisciplinary, interdisciplinary and transdisciplinary frameworks. In-practice examples of these frameworks in alternative industries and contexts provide evidence for application as well as an opportunity to examine their pros and cons.The paper closes with a call to re-examine working practices in the mining industry, with a view to enhancing productivity and heeding the call for greater innovation.CITATION:Coombes, J, 2016. Transcending the mining discipline divide – multidisciplinary, interdisciplinary or transdisciplinary?, in Proceedings Project Evaluation 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By R N. Humphries, R J. K Thompson

Large-scale coal mining in South Wales dates back to the late 18th and early 19th centuries with the birth of ironmaking on an industrial scale. This rapidly gave rise to new and large communities with immigration from far and wide across the United Kingdom (UK). These new communities were largely dependent on coal mining and served as the main form of employment and social cohesion until the industry’s demise in the 1990s. With wholesale mine closure and the concomitant loss of employment, the extensive environmental degradation and chronic mine-related illness left a deep scar on the psyche on many still living in the South Wales mining communities. This coupled with memories of strife in the 1980s has resulted in ongoing hostility toward the surface coal mining of the remaining accessible coal reserves in the proximity of these communities.The purpose of this paper is to set out the historical basis of the concerns of these legacy mining communities in South Wales and explain how they are being positively addressed by both the recently evolved planning and regulation system and by today’s surface mining industry. Reference is made to experience gained from two recent applications for surface coal mining adjacent to former mining communities. Ways are suggested in the approval process that surface mining can work in more harmony with the local communities through working partnerships between the mining company, the authorities and regulators and the affected communities. It is concluded that partnership is key to creating a more responsive mine-operating culture and a means to securing approval for future surface coal-mining prospects in South Wales, and probably elsewhere too.CITATION:Humphries, R N and Thompson, R J K, 2014. Surface mining and legacy mining communities in South Wales, UK, in Proceedings Life-of-Mine 2014 , pp 399–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By L Galisson, E Audigé, D Sowers

Establishing a robust geotechnical instrumentation and construction monitoring plan is one of the keys to the successful delivery of the world’s largest soft-ground bored tunnel in Seattle, Washington. The paper describes and provides a return of experience on current and best practice for monitoring tunnelling projects in urban areas. The owner’s contractual approach is discussed to highlight the flexibility of the design-built contract in achieving equal or better solutions by allowing for the use of innovative technics. Special attention is given to the management and involvement of third parties (building owners, utility owners), including the public, to overcome all challenges faced during the installation of the monitoring system in downtown Seattle for over 1000 instruments. Finally, the authors present the strategies implemented for managing the monitoring data and communicating with the owner, contractor and stakeholders.CITATION:Sowers, D, Galisson, L and Audigé, E, 2014. Current and best practice for monitoring tunnelling projects in urban areas – Alaskan Way bored tunnel, Seattle, Washington, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By I Govender, T L. Moodley

Tumbling mills are grossly inefficient, using only 5 per cent of the total energy supplied for actual breakage. A significant proportion of this inefficiency is unavoidable owing to geometric limitations; rotating drum systems are prone to exhibiting certain regions (energy barriers) that resist particle entry thereby restricting the transfer of energy. Though such systems are inherently inefficient, improved modelling schemes may lead to slightly enhanced efficiency through better microscale predictions of key breakage drivers (stress, force). Central to achieving such incremental advances is the development of a universally accepted rheology for dense granular flows. Armed with a better understanding of these macro-scale ingredients, classical process modelling offers an efficient, spreadsheet friendly framework for recovering the spatial distributions of the comminution drivers. At this real-time level of process control, it should be possible to tune comminution operations towards more energy efficient configurations – the ultimate goal of this research. The present work employs validated DEM data to recover the full continuum field which will ultimately serve as a basis for calibrating process model outputs based on different rheological hypotheses. Such a continuumbased approach captures tensor properties like the shear stress and strain rate – both of which are necessary to developing a dense granular rheology. Moreover, DEM captures this data at the momentum transfer timescale of 10-6 s – no other measurement technique is capable of this level of spatial and temporal resolution. Importantly, the confidence in this DEM data is strengthened because it has been validated at the continuum scale using Positron Emission Particle Tracking (PEPT) kinematic measurements. Validated DEM data is derived from batch experiments conducted within a 300 mm ID laboratory drum using three and five millimetre glass beads at 60 and 75 percent critical speed; such mill speeds are typically encountered in the tumbling mill industry. Dimensional analysis is conducted using critical rheological parameters (shear rate, shear stress, granular temperature etc), which are key to not only developing a granular rheology but ultimately will be used to tune our mechanistic models.

Aug 24, 2022

By C T. Dunbar, P A. Walker, G E. LeJuge

A programme of blast improvement was initiated at the Mt Whaleback iron ore mine by BHPIO management in early-1998. One component of that work was the need to improve wall control blasting practices to better achieve the designed pit slope elements. This paper describes the geological conditions in which pit walls are developed, the mine operating equipment, the blast design concepts applied to minimise blast damage, the techniques applied in an assessment of the blast performance and the operational procedures developed to ensure that the blast concepts are effectively implemented in the production environment. Substantial changes have been implemented in both technical and operational aspects of the mining operation in order to achieve the improvements in pit wall condition, in particular recognising the need for a more flexible approach to limits blasting in response to highly variable and complex geology. The benefits to the mine are not only an improved wall condition, but increased confidence on the part of mine management that mine plans may be implemented on design and on schedule.

Jan 1, 2001

I have headed this paper with a question and for the impatient among you ûthe answer is no we have not run out of developments but, and it is a big æbutÆ, we need to be innovative and ahead of the game or ænoÆ will be æyesÆ before we know it.Why do I believe that our future lies in innovation? Thirty years ago, knowledge doubled every 14 years. It is now doubling every seven years. In 1965, Gordon Moore, one of the founders of the chip maker Intel, made an observation that growth in memory chip performance is doubled every 18 months which became known as MooreÆs Law. Now there is fibre law, where the transmission line capacity doubles every nine months and storage capacity, under disc law, doubles every 12 months. What does this mean? Well, firstly there is a massive rise in information flow and availability with no limits in growth for at least the next ten years. Secondly, unlike our grandfathers, we are most unlikely to be employed by the same firm for our working career - we may not even have the choice to stay with the same company. In a phenomenon Richard Foster and Sarah Kaplan (2001), borrowing from Schumpeter, termed æcreative destructionÆ, companies are unable to sustain market-beating levels of performance for more than ten to 15 years. In the 1920s the turnover rate of companies in the United States was 1.5 per cent, so a company could employ almost three generations from the one family. A company had a half life of 60 years. In other words, you could well be in the same working environment as your grandparents. Today the churn rate is estimated to be eight to ten per cent. A company has a half life of five to six years. So for large companies, as an employer or employee or as a contractor, your working environment has a 50 per cent chance of changing in five years. Innovation is the driver of this rapid rate of change. Innovation is not for the faint hearted (Cutler, 2001) but it is the core for success in the global economy. The rate of change in our world is not going to decrease. We must learn, not only to manage change, but to enjoy the process of changing û to ride the tsunami of the knowledge economy.

Jan 1, 2002

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

By P Minkkinen, J Lohilahti, T Korpela, B McPherson

Concentrator plants intake the ore from the mine and produce concentrates by extracting valuable minerals in a succession of process steps. Controlling the extraction process and detecting changes in the process requires updated information on a minute basis. Moreover, due to economical reasons, one must also collect metallurgical samples on a daily basis for monthly reporting.In this paper, we present how slurry samplers were installed in a Cu-Ni flotation plant to accomplish the aforementioned tasks. An on-stream elemental analyser at the plant is used for flotation process control by taking samples from selected process streams. Two process streams, the flotation feed and tail, are also equipped with metallurgical samplers. The metallurgical samplers were designed to have low head loss, be robust and easy to maintain and to collect slurry samples in a reliable way for the metallurgical accounting.Samples were collected by different sampler types and we discuss the uncertainty arising from sampling in the assays. Variographic analysis was carried out on the process data in order to find periodic components in the process, and estimate the correct number of shift sample increments and measurement error components. The metallurgical samplers were proven to be reliable devices with zero downtime and no sanding issues in the main process flows. In addition, we show that the tail measurement is the most important one for the plant recovery calculation, which emphasises the importance of the sampling accuracy in the tail stream.CITATION:Lohilahti, J, Korpela, T, Minkkinen, P and McPherson, B, 2014. Analysis of slurry sampling arrangements at a froth flotation plant, in Proceedings Sampling 2014 , pp 91–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By T Ireland

The Project Hobson tunnel excavation was the first use in New Zealand of an earth pressure balance (EPB) tunnel boring machine (TBM). The tunnelling on the project was very successful and break-through was achieved three weeks ahead of program, demonstrating that tunnelling can be undertaken in Auckland with a high degree of cost certainty.Project Hobson involved the replacement of an existing 90 year old above ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which had reached the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally lined bored tunnel. The NZD$ 118 M project has provided several environmental benefi ts to the Owner, Watercare Services Ltd and the local community:· provide capacity to meet projected growth in the region,· virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, and· remove an obtrusive visual feature and open up the bay for recreational purposes.Auckland’s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the city centre.The paper describes the design and construction challenges for the projects, including TBM performance, ‘sticky spoil’ management, and risks associated with basalt lava flows and two paleovalleys. The paper also highlights the reasons for the success of the project, including a rigorous approach to risk management during design, and effective planning during construction. Other useful data such as the effect on the watertable caused by closed face tunnelling, and ‘faceloss’ estimates derived from settlement arrays are included in the paper.Project Hobson also saw the successful implementation of a Geotechnical Baseline Report – one of the first uses of this type of document in Australasia.

Mar 8, 2011

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Manfrino

The Iron Bridge magnetite mine and infrastructure project is currently in development as a joint venture between Fortescue Metals Group, Formosa and Baosteel. It is supported by an extensive database of reverse circulation drill hole samples analysed by X-ray fluorescence (XRF), with a large subset tested for concentrate mass recovery, concentrate and tail grades by Davis tube recovery (DTR) testing. A limited number of rock physical testing results, including unconfined/uniaxial compressive strength and crushing work index, completes the database.By combining all available information – assays, DTR results, geology, stratigraphy, mineralogy and rock physical results – and using multivariate statistical analysis techniques, the impact of the critical factors that control concentrate quality, mass recovery and grindability characteristics have been outlined. A set of geochemical groups was created by using a cluster analysis technique from the combined XRF-DTR data. These groups allow optimal separation of material with consistently high concentrate Fe grades and mass recovery. This approach is superior to domaining based on stratigraphic logging or mass recovery as it is commonly used in standard magnetite estimation models. Using the results of a normative mineralogy study, the main geochemical groups were given a mineralogical profile fitting their geochemical characteristics. These findings further refined the understanding of the link between the process characteristics of the samples and their geochemical signature and mineralogy.The geochemical grouping defined on head grades and DTR concentrate mass recovery was generalised into a ‘geomet’ code based solely on the routinely assayed head grades, thus bypassing the need for systematic DTR testing. The geomet code identifies spatial domains with homogeneous geochemistry, mineralogy and process characteristics in both oxide and fresh material that form the basis of the current Iron Bridge resource model. The allocation of geometallurgical characteristics in terms of concentration amenability and concentrate characteristics on a block-by-block basis over the whole project allows for an optimum mine schedule and plant feed. This ensures that the desired concentrate characteristics and mass recovery can be better predicted over the life-of-mine, thereby improving the mine’s economics and stability by derisking the mine schedule and optimising the performance of the concentrators. A key benefit of the geomet code devised for the Iron Bridge mine is that it can be attributed in an automated manner to all samples analysed for a routine XRF analytical suite, from exploration to blasthole drilling. This allows each sample to be allocated to a geometallurgical material type with predictable process response in terms of concentrate mass recovery and concentrate quality without the need to complete systematic DTR testing.A standard multivariate analysis coupled with a cluster analysis has allowed the linking of interdisciplinary results between geology, mineralogy, geochemistry, process and metallurgy to better understand, predict and ultimately mine and process the Iron Bridge deposits. This allows plant operations and product quality to be optimised through each stage thanks to the predictable ore characteristics embedded in the mining model.CITATION:Manfrino, A, 2015. Unravelling the factors impacting on concentrate quality by geometallurgical data analysis at Fortescue Metals Group’s Iron Bridge magnetite mine, in Proceedings Iron Ore 2015, pp 567–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Kasai H, Hibi T, Matsuishi S

Coal oil mixture (COM), a liquid fuel pro- duced by mixing together coal and heavy oil on the 50-50 basis, has been brought to a level of practical use in Japan, being actually employed by a oil fired system at Yokosuka Thermal Power Station of The Tokyo Electric Power Co., Inc. A COM Production Plant, built in Onahama which is located about 160 miles from Yokosuka, required COM to be transported by sea. Mitsubishi Heavy Industries, Ltd. therefore performed a series of studies to develop a spe- cialized COM carrier, the world's first of its kind. Long lasting high stability is of pri- mary importance to successful use of COM. Much have been done in the way of research on stability of COM in the static storage, and the mechanism of COM static: stability is almost completety known. On the other hand, the knowledge about the COM dynamic stability, such as the stability while being transported aboard the COM carrier at sea, is still limited at the moment. The motion of COM aboard the COM carrier and how COM would settle were studied by tests. A visualization test on the COM behavior under dynamic motion was also performed and the mechanism of COM dynamic stability was analysed. The tests showed that the ship rolling motion had @n effect of promoting the settling of coal content of COM in the cargo hold. And studies were also made to device a method for esti- mating the settling quantity of coal during sea Transportation.

Jan 1, 1987

CSA mine, which is a deep level copper operation, located 12 km north of Cobar, NSW, currently uses a top down stoping method, utilising cemented hydraulic backfill (CHF) to fill and stabilise the stoping void thus assisting the extraction sequence. The stope sequence then requires development back through the CHF stope so that the necessary infrastructure for the subsequent stoping, such as raise bore pads can be sited. The primary and secondary support installed in the CHF consisted of 100 mm thick fibrecrete from floor to floor with 7 + 2.4 m long resin support tendons installed at 1.5 m ring spacing. This support system relied on the resin achieving a quality bond with the CHF, and also the fibrecrete developing early structural strength due to the use of an accelerator. In addition to the delays in the excavation turn around time, it was felt that a superior support system could be designed. Such a system was designed; risk assessed, tested underground, and trialled in selective CHF digouts, and eventually signed off as the chosen support method in CHF digouts. This paper discusses the change from a passive support system used in CHF digouts to an active support system using Swellex bolts and weld mesh, which has provided an active support system, that is superior, faster to install, reduced the excavation turn around time and is overall a cheaper support system.

Nov 25, 2010