Search Documents

By Paul F. Kerr

The uranium-producing areas near Marysvale, Utah provide an unusual group of veins and replacement deposits associated with a Pliocene-Oligocene intrusive and extrusive igneous complex. Aside from several scattered occurrences in older volcanics, uranium-bearing veins occur in intrusive quartz monzonite or granite and in nearby rhyolite. The veins in general trend within a few degrees of N55-65°E, are more or less vertical, and are found along the western margins of a quartz monzonite intrusive. The replacement deposits are found in rhyolite intrusives and also in the lower portions of rhyolite flows close to places where veins forming solutions rising through quartz monzonite came into contact with the rhyolite. At least 14 veins have been mined since uranium mining operations began at Marysvale some 16 years ago, while ore has been extracted through about 10 miles of underground workings. The active mmmg area is approximately 3000 feet long and in the central portion 1500 feet wide. Ores have been found over a vertical spread of almost 2000 feet, between the highest occurrence on Jungfrau Hill ( ca. 7200 feet) and the deepest discovery of ore in a drill hole near the Prospector Mine (ca. 5200 feet). Under existing mining and marketing conditions, mining along the veins in the main area appears to have reached an economic limit at about 500-600 feet below the surface. However, orebodies in the rhyolite and in the upper portions of veins close to the rhyolite are subject to active mining. Isotopic dates indicate that the uraninitebearing veins and replacements are late Miocene or Pliocene (ca. 10-13 m.y.), the rhyolite is Miocene (avg. 17.5 m.y.), and the quartz monzonite and granite intrusives are late Oligocene (23.6 to 26.0 m.y.). The older Bullion Canyon Volcanic Series which encircles the area is Oligocene (28 to 31.1 m.y.). Two generations of alteration occur: ( 1) Earlier alunitic veins and replacement bodies are found in the Bullion Canyon Volcanic Series, none of which have produced uranium; (2) Later argillic alteration associated with the introduction of uranium is found along veins, replacing glassy rhyolite dikes and replacing phases of the rhyolite.

Jan 1, 1968

By N. A. Gokeen, M. Ohtani

EFFECT of elements on the solubility of carbon in liquid iron is useful in calculating and correlating a number of thermodynamic properties as shown elsewhere in detail.' Kitchener, Bockris, and spratt2, and later Turkdogan and Hancock3 have investigated the effect of sulfur on the solubility of carbon at various temperatures and concentrations. For any chosen sulfur concentration, the solubility of carbon reported by Kitchener et al. is considerably lower than that by Turkdogan and Hancock. It was therefore felt that a reinvestigation of this problem was necessary. EXPERIMENTAL METHOD An alloy of Fe-C-S .was prepared with electrolytic iron and ferrous sulfide melted by induction in a graphite crucible, 4 in. high 1 1/2 in. ID under a CO-atmosphere. The temperature, held at 1500" ± 5°C in all experiments, was measured with a Pt-Pt + 10 pct Rh thermocouple immersed into the melt. In order to assure saturation with carbon, the melt was stirred with a graphite rod. After approximately 1 hr at 1500 °C, a sample was obtained by sucking the melt into a silica tube, 4 mm ID. The sample was then analyzed for carbon and sulfur by usual methods. RESULTS The results are presented in Table I and plotted in Fig. 1 with the individual values of Turkdogan and Hancock.3 Scattering in the data is equivalent to 3 pct or less in carbon analysis. The broken line represents the empirical equation obtained by Kitchener et al. from their data. It is evident that the present data are in good agreement with those of the former investigators but in disagreement with the latter. The cause for this discrepancy cannot be readily offered since the experimental methods in the three investigations were nearly identical. Additional evidence corroborating the author's results may be presented in the following manner. The difference between the solubilities of carbon in the ternary Fe-C-X melt with a small concentration of any element X, and in the binary Fe-C melt is %?C = %CIII-%CII [1] where %?C is the change in solubility, and %CIII and %CII are the solubilities in the ternary and the binary systems respectively. The value of %Cii

Jan 1, 1961

By F. M. Morris

A large reserve of thick coal in southwest Virginia was developed by Clinch-field Coal Co. in 1957-1958 to produce a nominal rate of 1500 tph raw coal. Operation features coal cleaning in transit. Refuse removed averages 35 pct. Evolution of plant from initial conception to completion is discussed, selection of means applied is explained, and performance to date us design expectation is described. The long-range plan calls for ultimate handling capacity of 40,000 tpd raw coal with anticipated clean coal capacity of 26,000 tpd on a three-shift basis. From a materials handling viewpoint, the Moss No. 3 operation is principally of interest as an ensemble. Generally speaking, it uses time-tested equipment and ideas but some of these are employed on a scale that may be new in the industry. At present about 20,000 tpd of raw coal are being handled. This is expected to increase to 40,000 tpd as soon as business conditions justify it. The purpose of this paper is to discuss the evolution of the plant as to materials handling practices, to describe briefly the equipment and methods used, and to comment on performance in certain areas. The subject divides itself naturally into four phases: 1) operations at the mines, 2) transportation from mines to plant, 3) raw coal handling into the plant, and 4) transportation of refuse away from the plant. OPERATIONS AT THE MINES The coal reserves for Moss 3 are in southwest Virginia where Dickenson, Russell, and Buchanan Counties come together. This area contains about 15 square miles and over 100,000,000 tons of coal. Here the No. 4 (Tiller) and No. 5 (Jawbone) seams of the Norton Formation lie so closely together that for practical purposes, they constitute one seam of coal. This seam, which is called the Thick Tiller, varies from 10 to 18 ft in thickness and underlies Sandy Ridge, a mountain cresting between 2400 and 3300 ft above sea-level. At 18-ft seam height (which is considered to be the maximum practical mining height) the parting between seams will be about 3 1/2 ft thick and each bench of coal will be about 7 ft thick. Depending on the amount of impurities in the seams Drover. total reject in this height coal may approximate 50 pet by wt. It will average about 35 pet for the property as a whole. The first move in developing this resource was made in 1953 when contour maps of several square miles around Duty, Va., including all the known outcrop, were made by photogrammetry. At this time, it was felt the prospective operation would be served by the Clinchfield Railroad and a photogrammetric route survey was made by this railroad from Haysi to Duty. Study of the resulting maps indicated only one site—adversely owned—which might accommodate the size washing plant to be erected. Water resources of a dependable nature seemed nonexistent. In 1954 bulk washability tests were made on the Tiller Bench at the Moss No. 1 preparation plant. The tests indicated this portion of the seam, mined separately, would wash to 4 pet ash with good recovery. Also in 1954, development of Moss No. 2, south of Sandy Ridge, was begun. This mine is in the Tiller Seam where it is about 100 ft below the Jawbone Seam. The reasons for developing a mine in the normal Tiller Seam before tackling the Thick Tiller seemed compelling: Railroad service could be established quickly, communications were better (though not good!), more was known of the seam (it had been mined in the years 1911 to 19241, and there was no essential property to be acquired. After some legal skirmishing, the Norfolk & Western Railroad was granted the right to serve the new mine. Three decades earlier the old mine had been served by the Clinchfield Railroad. The event which triggered active development of Moss 3 was the Appalachian Power Co.'s decision in 1956 to build a 450,000-kva power plant on Clinch River at Carbo. This solved the problem of marketing the steam coal which inevitably must be a product of a mine in the Thick Tiller. Management promptly decided to build the preparation plant at Carbo where an excellent site was owned; where railroad service existed; where telephone service could be obtained; and where roads, bridges, and water supply were tolerable.

Jan 1, 1961

By Young C. Kim

The use of computer models to design the ultimate open pit limits during feasibility studies as well as during long-range mine planning is becoming an enforced practice in all types of mining, e.g., ferrous, non-ferrous, and coal. As a result, the state of the art in computerized ultimate pit limit design methodologies and associated computing and optimizing techniques has advanced considerably in recent years. Unfortunately, very little has been published to date regarding the preferred ultimate pit limit design philosophy, i.e., optimizing us satisfying, or regarding the modeling approaches being used for different types of orebodies. This paper reviews the current state of the art in various modeling approaches and optimizing techniques that are in use for different types of deposits, through available literatures and personal communications.

Jan 1, 1979

By Eugene McAuliffe

THE last obtainable figures of the value of the coal mining investment are those contained in the U. S. Census Reports, from data gathered in 1919. The values shown therein and set forth below cover lands and equipment and do not include distribution and marketing facilities. The working capital necessary to meet pay rolls to purchase material and supplies and workmen's compensation insurance are likewise excluded.

Jan 1, 1926

By Arnold S. Epstein

Tlze green electroluminescence occurring at liquid-nitvogen temperature in epitaxial gallium phosphide diodes is exarnined using the donor dopants silicon and sulfur. Zinc is used as the p-type diffusant. Two tt~ain peaks are found, namely til 0.56 and 0.535 p. The intensity of the gYeen peak occurring at 0.56 is found to oary as -4"' wlzere Jf is the forward current density and to first order appears to be dependent on the concet~tvation of ionized donovs. Tile vadintive lifetinze fov this process is -10-'sec. The intensity of the 0.56-p lu~ninescence is nt least several ovdevs of magnitude greate,, at liquid-nitvogen temperature than that noted jor the 0.538 radiation for current densities up to about 35 amp per sq cm. The variation oj- the intensity of. the 0.538-p peak with current density caries according to the donor dopant. With sulfur as the donor one has a J12 dependence, whereas when silicon is the donov a J1.5 dependence is noted. Tl~e above can be fitted to a In molecular process (in first order) such as a band to band recombination. The constant B fir band to band vecombination) is found from our experitt~etlt to be of the order of 2 CZI cm per sec, zcl~ereas for tlze impurity vecombination peak (0.56 p]) tile A cotzstor~t is of the order of. 7 x 10-' cu cm per sec. The structuve o/. the diodes at liquid-nitvog-en tett~peruture is oj tlze double injection type, and by carefi~lly selecting. the thickness of the structure one can regulate the onset of the 0.538-p radiation. The diode clzavaclevistics follow an I-Vx laiv where x is >1. Llregatiue resistance in these structures con be correlated with saturation of tlze 0.56- peak. ThE development of high-purity, large single crystals of epitaxially grown gallium phosphide is the ultimate aim of the studies to be reported. While a number of papers and reviews' have been presented on properties of gallium phosphide grown from gallium solution and from the melt, less attention has been paid to the properties of epitaxial gallium phosphide grown from the vapor. In the studies to be reported we have examined the effects of shallow donor impurities, primarily silicon and sulfur, at liquid-nitrogen temperature, on both the electrical and green electroluminescent properties of carefully characterized single-crystal epitaxial Gap. I) EXPERIMENTAL PROCEDURES A) Material Preparation and Properties. The samules used in this investigation were single-crystal n-type epitaxial gallium phosphide. he single crystals were synthesized from the elements by vapor transport and epitaxial deposition on single-crystal gallium arsenide substrates. Typical transport agents used were chlorides. The growth procedures are described in more detail in Ref. 2. The samples were grown in the (111) orientation and had thicknesses up to 480 . Following the growth, the GaAs substrate was removed from the epitaxial Gap by etching in nitric acid. The Hall effect and resistivity of these n-type samples were measured as a function of temperature and analyzed for impurity content and compared with spectroscopic emission analysis. The results are given in greater detail in Ref. 3 but a summary is noted in Table I. In Table I, AED denotes the donor ionization energy, Nd is the donor impurity concentration, lvA is the acceptor impurity concentration, NI is the total impurity concentration, Rip vs temperature is the measured Hall mobility-temperature relationship from liquid nitrogen to about 400"K, n(77"K) is the measured carrier concentration at liquid nitrogen, and R/p(77'~) is the measured Hall mobility at liquid nitrogen. Good agreement is noted between electrical and emission analysis for the major donor impurity, silicon, in the two materials where it is a major constituent. In the case of the two samples SC90-6 and AP138-3(111) B which were sulfur-doped the ionization energy found from the electrical data is in good agreement with that reported for sulfur.4 The acceptor impurities are not known, although from the presence of magnesium in the samples as indicated by emission analysis and its known role as an acceptor in GaP,4 magnesium could be present as an acceptor. Similarly, since silicon is known to be an amphoteric impurity4 it may also be present as an acceptor in the Gap.* The *A small band has been noted at 0.625 11 in samples SC90-6, SC76-4, and SC77-4, suggesting according to Ref. 5 that sillcon could be present as an acceptor In these samples since these authors have found this peak to represent a donor-silicon emission. presence of calcium deduced from emission analysis is not correlatable with the electrical analysis and its presence as an electrically active impurity should be questioned. B) Sample Preparation and Diode Fabrication. The original slices were of the order of 2 sq cm in area witi the (111)B face up. The material was cleaved and sectioned and the best pieces selected (i.e., those which visually appeared to have the least strain and defects). The samples were polished, lightly etched, and cleaned in trichloroethylene. Zinc was diffused in a closed tube at 800°C to form a p-n junction. Diodes were made from these samples. The depth of junction varied, but did not exceed 10 p depth. The back side of the slice was lapped back and a low-resistance n-type contact was formed (at 600°C in forming gas) to an Au-Mo tab with a hole in the middle for

Jan 1, 1968

By A. T. Yu

The energy crisis and the resurgence of mining activities highlighted 1972-73. Added to the impetus for more effective materials handling systems has been the continued upward trend of inflation and labor costs. The need for addressing the fundamentals has led to the trend toward an overall systems approach to materials handling problems.1 The decision to move forward with large mining ventures such as the $150 million Hibbing taconite comple2 and the immense Carajas iron project must base themselves on indepth studies of a host of factors viewed in the context of an integral mine-transport-market system. What's important is that each ton of pellet or ore must be an economical commodity at the end users' furnace. The project can still be viaable even if certain components in the entire network appear to be individually costly.

Jan 2, 1974

By R. G. Aspden, D. A. Colling

THE {120}(001) texture has been reported in near 50 pct Ni-Fe alloys <0.004 in. thick1,2 and in copper 0.014 in. thick.3 This texture is one of two types of secondary recrystallization textures observed to replace a cube texture matrix and is desirable in Fe-Ni alloys because of its unique magnetic characteristics.1,2 However, the conditions for and mechanism of the {120}(001) formation are not well understood.3 During an investigation of the influence of alloying elements on the magnetic characteristics of 49 pct Ni-Fe alloys with a sheet thickness of 0.014 in., we have observed the growth of {120}(001) secondaries when strong deoxidizers such as aluminum and calcium were present. It is believed that this observation in unique and provides additional insight with regard to the mechanism for {120}(001) texture formation. Three alloys were prepared with electrolytic iron and nickel and contained a nominal 49 wt pct Ni. Alloy A was a straight binary Fe-Ni alloy, whereas intentional additions of 0.013 wt pct Ca to alloy B and of 0.59 wt pct A1 to alloy C were made. Ingots were forged at 1100 C, hot-rolled to 0.150 in. gage, pickled, and cold-rolled to 0.014 in. Standard U-shaped magnetic test specimens were punched, deburred, sprayed with MgO, and annealed in ~50°C dew point hydrogen. Textures were identified with the aid of etch pits, the

Jan 1, 1970

By Harry C. Wiess

PETROLEUM has come to be one of the most important and essential of the mineral re- sources of the nation. It is the most advantageous source of mineral fuels and of lubricants, and as such it has provided in large measure for the phenomenal development in our modern means of travel and in the facilities for transportation by land, sea, and air. Without it the remark- ably rapid industrial and social progress in our country during the past thirty years could not have occurred. In view of its important place and the fact that petroleum is irreplaceable and existent in limited quantities in nature, its conservation is essential.

Jan 1, 1939

By R. V. Norris

The great coal strike of 1902, which confined the work at the Short Mountain colliery of the Lykens Valley Coal Com pany almost exclusively to pumping, gave an opportunity to determine with considerable accuracy the cost of pumping the water from these very old, extensive and wet mines. This colliery, which is located in the extreme southwestern end of the anthracite coal-field, has been operated continuously since 1836, and has shipped 7,747,313 tons of coal. This and the Williamstown colliery are the only operations in Dauphin county. The workings cover about 5 miles along the North dip of the extreme westerly end of the basin, with the operating slopes near the center. They extend around the westerly spoon of the basin and back about 31/4 miles easterly on the South dip. The mines are very deep, the present workings ex tending to 711 ft. below sea-level, and about 1600 ft. below the lowest surface-opening. The coal is hoisted principally from the Short Mountain slope, which is 1550 ft. long, with 26 to 68 degrees dip, and from an inside slope, No. 4, 800 ft. long, with 52 to 72 degrees dip. The ordinary capacity of the colliery is about 1000 tons per day, and the average output for the years 1897 to 1901, in clusive, was 297,000 tons per year. The seams worked are the lowest Red Ash measures, being, respectively, Nos. I, II and III of the coal-bed series, but locally called the " Little Lykens," " Lykens," and " Whites." On the accompanying plan the Lykens seam is shown in full and the Whites in dotted lines. The pumping-plant is divided into four lifts, the pumps being located as shown in the section, Fig. 1, and the plan, Fig. 2.

Jan 1, 1904

By M. Cohen, P. E. Beaubien, D. Caplan

Addition of 1 pct Mn to Fe-26 CY ca/(ses a12 increase in scaling rate at 870° and 1090°C. Whereas only the rhombohedral oxide, formrs on tire manganese-free alloy, with manganese present major amounts of the spinel .Mn0 . Pro-duced through which diffusion is more rapid. At 1090°C the scale formed OH Mn is highly, irregular due to blistering and sintering, This is a second cause of faster oxidation Since much of the blistered oxide does not participate as part of the protective layer. The oxide phases that form at different times depend on the degree to which the surface metal has become depleted, in manganese by preferential oxidation. PREVIOUS work has demonstrated that the oxide scales formed on chromium steels at high temperature consist of both spinel and rhombohedra1 phases and may contain considerably more manganese, especially in the spinel phase, than is present initially in the alloy.&apos; It has further been observed that a binary Fe-26 Cr alloy scaled less rapidly than an equivalent commercial steel and formed no spinel.&apos; However, it is not established if manganese in chromium alloys actually promotes formation of spinel nor if it affects oxidation resistance. It seemed expedient to try to evaluate the specific effect of manganese by oxidizing an Fe-26 Cr alloy containing a small manganese addition under the same experimental conditions as used for the manganese-free alloy.&apos; EXPERIMENTAL Table I shows the composition in weight percent of the Fe-26 Cr-1 Mn alloy and of the Fe-26 Cr alloy used as reference. The alloy with manganese was prepared from the vacuum-melted Fe-26 Cr alloy by remelting in vacuum with the proper manganese addition. The ingot was rolled to strip and specimens 1.1 by 0.035 by 5 cm and 1.1 by 0.5 by 4 cm cut out or machined. As previously described2 the specimens were smoothed by abrading through 600-grit Sic paper, electropolished in acetic-perchloric acid (20 to 1) to remove 10 p of metal, annealed at 1100°C in 20 torr of purified argon, and electropolished to remove a further 10 p of metal. They were then either rinsed in water and methanol and blotted dry or immediately etched for 45 sec in deoxy-genated 4 N HC1 under cathodic polarization at 10 pa per sq cm. Oxidation runs were carried out in a vertical tube furnace in a flow of purified oxygen at 1 atm while the weight increase was recorded continuously on a* automatic balance.3 Alter 98 hr at 870.C or 20 hr at 1090"C the specimens were removed to flowing argon and observed microscopically for evidence of spalling as they cooled. Subsequently they were examined by X-ray diffraction, the oxides analyzed chemically, and metallographic cross settions prepared. RESULTS Figs. 1 and 2 show the oxidation curves of Fe-26 Cr-1 Mn at 870&apos; and 1090C. The Fe-26 Cr reference runs are shown as dashed curves. Experimental details of the six runs are included in Table 11. The first 20 hr of run 1 is repeated in Fig. 2 to show the effect of temperature. At 8&apos;70°C the weight gain for Fe-Cr-Mn is about twice that of Fe-Cr (curve 1 vs curve 2, Fig. 1). Both alloys show regular oxidation curves. On parabolic coordinates (right-hand scale of Fig. 1) the

Jan 1, 1965

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling&apos;s work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman&apos;s experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman&apos;s plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By W. A. Forbes

OUR present-day geological surveys show that 36 of our States are underlain with bituminous coal, covering a total area of 496,709 square miles. The North American continent possesses 69 per cent of the world&apos;s coal reserves, with the United States alone having an estimated 55 per cent. The American coal reserves, in tons, are calculated to he about 3,500,000,000,000 tons, of which we have exhausted about 1 to 1 1/2 per cent. If this coal were mined at the rate of the 1918 production-a record output of 579;000,000 tons-it would not be depleted for 4,000 years. The more easily accessible and high-grade coals would obviously be consumed much before this; some estimates are 100 years. The natural progress of the nation&apos;s industries up to 1910 encouraged on every hand the development of new mines, especially where cheap and easy access to coal measures was coupled with short hauls to the consumer. Over-development resulted, which is perhaps today one of the fundamental causes for the many difficulties faced by the coal industry, which is highly competitive; about 70 per cent of the production cost is labor. Salient statistics for 1930, recently issued by the U. S. Bureau of Mines, follow:

Jan 1, 1932

Jan 1, 1968

By Claude P. Heiner

While the title of this paper embraces the entire West Coast, the author, in the interest of simplification. has confined the discussion to California-particularly the central section. California&apos;s population has, risen 45 pct since 1940. Its electric requirements have also increased, not only because of the growth in industry and population but also because of the widespread tendency of all types of electric consumers to use more electricity than ever before. The growth of California&apos;s electric utilities is shown by published data covering operations, of three of its large systems and is given in Table 1.

Jan 1, 1949

By A. E. Seaton

In this paper it will be my endeavor to trace the development of the marine engine and its appurtenances, and the general progress that has taken place in marine engineering generally during the past fifteen years, rather with the object of attributing much of it to the successful efforts of the makers of iron and steel, thereby rendering my thanks to them for the valuable service they have contributed to my profession, than to recount what has been achieved by the skill, ability and perseverance of my colleagues in shipbuilding and engineering. The engineer has been at all times dependent on the ironmaster, and on more than one occasion his progress has been barred by the inability of the latter to overcome some obstacle to success in his manufacture. But on the other hand, it is equally true that the ironmaster has often been ahead of the engineer, and has been prepared, long beforehand, to supply that which would make a success for the marine engineer if he would avail himself of it.

Jan 1, 1891

The Role of the Drilling Contractor BY FERRIS E. SAINSBURY Ron Haxby, Occidental Minerals What is the best method for drilling a 12-in. diam hole to a depth of 1200 ft and maintaining the deflection within 25ft from vertical? Ferris Sainsbury: In order to drill a 12-111. hole down to 1200 ft, In most places you would have to employ a rotary tricone bit With a down-the-hole hammer, I expect by that depth significant Inflows of water would be experienced Even with foams, we would not be able to get the water out of a hole of that diameter So the down-the-hole tricone method of drilling would be best. To keep it straight, we would probably employ the largest square drill stem compatible with the diameter of the hole. Ron Haxby: Is it common in drilling contracts to put in a vertical hole clause? Ferris Sainsbury: You can put in the vertical hole clause Ron Haxby: Does it cost more? Ferris Sainsbury: Normally, if the hole deviates, the driller can correct it with deflection wedges and will charge it back to you at cost, plus 10% or somewhere along that range Any drill hole has a tendency to go perpendicular to the dip, and there are times when stabilization systems are not successful in preventing the hole from turning into the dip of the formation. The only solution, in this situation, is to go in with an oriented wedge and kick the hole back out.

Jan 1, 1979

Jan 1, 1944