Search Documents

By Goro Shimaoka, Kichizo Niwa

IN the past, the crystalline states of graphite in cast iron have been studied by many investigators. Recently several authors 1-4 have published interesting information on the crystal texture of the individual graphite grain, especially spherulites in nodular cast iron. In regard to the crystal structure of graphite, Lipson and Stokes0 howed by powder X-ray analysis that most of the crystals contain about 14 pct rhombohedra1 structure (ß-form) which differs from the hexagonal structure (a-form) in the sequence of layer stacking. Hoerni6 onfirmed the existence of the ß-form in a single crystal with electron diffraction by Kossel-Moellenstedt's method. Furthermore, Hoerni and Weigle7 found extra reflections in electron diffraction patterns, which are given by a unit cell twice as large as the usual one in the basal plane. Recently, Lukeshs observed graphite twinning and satellite reflections in his X-ray work and considered them as evidence for the existence of an orthorhombic superstructure. Owen and Street" and Matuyama" studied the structures of graphite crystals in several types of cast iron, using the X-ray powder method, and they showed that the graphite crystal contains a certain amount of the ß-form, an amount which varies with the sources of the cast iron used. The present study was made in order to secure structural information on graphitization in cast iron. Electron diffraction studies on the structure of single graphite flakes segregated from molten carbon or silicon-rich iron at 1200" to 1500°C are reported. Experimental Honkeiko pig iron (4.05 pct C, 1.59 pct Si, and 0.65 pct Mn) was used as the solvent of carbon or silicon. The pig iron was melted in an open furnace and a small quantity of metallic silicon was added to the melt at 1300°C. The melt was heated to 150O°C, and then retort black carbon or metallic silicon was added little by little. The components added to the bath contained approximately 5.0 pct C and 2.0 pct Si in the carbon-rich material, and 3.8 pct C and 5.4 pct Si in the silicon-rich iron. These two types were held at 1500°C and then cooled without graphitizing by cutting the heat sup-

Jan 1, 1958

By T. S. Lovering

The Moffat tunnel passes through the continental divide about 50 miles west of Denver, Colo., on the Denver & Salt Lake R. R.: It is 16 ft. wide, 24 ft. high, and 32,383 ft. long, a distance of a little more than 6 miles. The advantages accruing from its construction may be briefly summarized as follows: The tunnel eliminates 27 miles of grade averaging more than 3.5 per cent. and actually running well over 4 per cent. in many places, and changes the steepest grade from 4.5 to 2 per cent. It reduced the peak of the railroad from 11,660 to 9249 ft. which enables one engine to pull four times as much freight as it could before the tunnel was built. If the Denver & Salt Lake R. R. completes its line, this road will shorten the distance between Denver and Salt Lake City by 200 miles and will have no steeper grades than the lines now connecting the two cities. The proposal to drive the tunnel through the divide dates back about 25 years and D. H. Moffat, who was the leading spirit in the organization of the Denver & Salt Lake R. R. spent much of his time and energy in efforts to raise money for the tunnel that bears his name. He was unsuccessful and died before the work was started. In 1920 an effort was made to obtain state legislation favoring a bond issue to finance three important railroad tunnels in Colorado but the measure was defeated, largely through the efforts of the citizens of the region near Pueblo. A few years later devastating floods caused the Pueblo voters to seek relief from the state and at this time they withdrew their objection to the tunnel bond issue. As a result, a $6,720,000 bond was issued to finance the Moffat tunnel. Construction bids were so high that the work was finally allotted on a scheme analogous to a cost-plus basis. The contract was awarded to Hitchcock and Tinckler, who are paid a fee of $140,000 for driving the tunnel. All bills are paid by the Moffat Tunnel Commission. The contract was let Sept. 19, 1923, and Hitchcock and Tinckler agreed to complete the work by July 19, 1927. In the event of finishing before this date they were to be given a bonus of $1000 a day and

Jan 1, 1928

By Enid C. Plante

To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), rnarcasite (FeS2), orpiment (As&.), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also exarnined to determine if its behavior could be correlated with that of pyrite or rnarcasite (FeS2. Experimental Method Mineral for Flolation and Contact Tests Mineral was prepared in the manner a1ready described1 and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and CO2-free air bubbled through each suspension at a constant rate (about I bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation , oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the 'supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.l No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 Flotation of "Unoxidized" Minerals with Ethyl Xanthate as Collector Fig I to 3, 4. 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox8 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1949

By W. W. Eckles

This paper is presented as a suniniary report of the use of well gas composition correlations obtained from mass spectrometer recordings as a means of identification and determination of reservoir continuity. Conventional methods for detecting composition differences are en-pensive, elaborate, and difficult to obtain. This excludes the use of extensive composition data for most applications. During recent years the mass spec-trometer has come into general use as an analytical tool in petroleum refineries. The use of mass spectrometer composition patterns ir~ characterizing or "finger-printing" the produced gas from a reservoir, presents a novel method for correlatitlg gas samples from well to well. The mass spectrometer provides a trace similar to an electric log. having peaks which represent the abuntlnnce of certaitz hydrocarbons in the well gas sample. Without going further into the detailed analysis the idea has been advanced that these traces or patterns could be used as a means of identifying a particular natural gas. This theory has proven to be essentially correct. The mass spectrometer pattern method is simple and cheap as COi?7pared to other standard methods. It greatly facilitates the solution of reservoir and geological problems in which correlation of well gas Com-positions is a factor. Specific field applications have been made. This paper concerns the results obtained in 465 individual gas analyses from 35 fields and 77 res- ervoirs. In a number of cases it has been found that such data have been extremely valuable in the determination of reservoir continuity. In at least one case, the method was a valuable contribution in tracing a reservoir from sand to sand in a coinplex fnulted field involving n11rnerous gas reservoirs. Field applications are presented to illustrate the possibilities of the method at the present stage of developnient and to stimulate the ernployrnent of this new approach by geologists and petroleum engineers in the industry. INTRODUCTION Identification of producing horizons and the determination of reservoir continuity are often a problem in those areas where dome structures and highly faulted sands are encountered. To complicate the picture further, there may be numerous sands, one on top of the other which dip and diverge in different directions. Even though it may be possible to develop some solutions to the preceding problems on the basis of the geological and reservoir data on hand. it is readily recognized that substantiating data based on independent methods would he extremely valuable. It has been found through field studies that correiation of well gas composition can be used to advantage in the geological and engineering study of a complex reservoir identification problem. METHOD FOR COMPARISON AND CORRELATION OF WELL GAS SAMPLES Since a large number of well gas samples are required in a gas identification or reservoir con- tinuity problem, it is necessary that a method of analysis be employed which can detect differences in composition readily and inexpensively. Although detection would be possible by means of low temperature fractional distillation (POD) analpsis, the method requires a relatively large sample and is comparatively slow and expensive to run. The mass spectrometer affords an inexpensive and precise analysis of small well gas samples taken at the surface which are about 1/300 as large as a POD sample. These samples can be obtained by regular field personnei and shipped to the spectrometer for analysis. It is, therefore, a practical approach to the problem. A typical record from the mass spectrometer is illustrated in Fig. I. The peaks on the record represent the abundance of ions produced from the different hydrocarbon molecules making up the gas sam-ple. In well gas comparisons only five peaks are employed, since the other peaks are formed from the same gas molecules and furnish no additional information. The five peaks used represent the abundance of methane, propane, ethane, butane and heavier, and oxygen. They are referred to respectively as the 16, 29, 30, 43, and 32 peaks. The oxygen peak is used to correct for air content in

Jan 1, 1958

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By H. R. Peiffer

Hardening of soft metals can be accomplished by dispersing finely divided hard particles in them. The dispersing of finely divided alumina in silver in the presence of oxygen yields a high strength material which is unusual in that its mechanical properties above the melting point of the continuous Ag-O alloy matrix are similar to other solids. The tensile strength is studied for two of these alloys, one of which contains 15 pct by weight alumina and the other 20 pct by weight alumina. The average fracture strengths above 960°C of these alloys were found to be 0.4 x106 dynes per sq cm and 3.8x106 dynes per sq cm respectively. The strengths appenred to be independent of temperature above 960° C. The creep behavior of the 20 pct alumina material was studied above 960°C. The initial creep rate, 6 , of this material can be represented by where s is the applied stress and E the activation energy for the process. This energy is of the order of 1.7 to 2.1 ev. HARDENING of soft metals by the addition of finely divided, hard particles has resulted in the production of materials with excellent creep resistance and with inhibited recrystallization.' It has been demonstrated that such composites have useful strength up to temperatures very near the melting point of the soft metals, but one might expect that the strengthening by the dispersed particles ceases to be of importance above the melting point of the softer phase. This, however, is not so.2 In this paper the strengthening of a liquid Ag-O solution by the presence of dispersed alumina is discussed and experimental data concerning the mechanical properties of such a material at temperatures above 960°C presented. EXPERIMENTAL PROCEDURE Specimens were prepared using powder metallurgical techniques. Finely divided silver oxide was mixed in the appropriate proportions with "Linde B" alumina. For these experiments the specimens contained 15 or 20 wt pct alumina in pure silver.* These alloys were used in these experiments since they were the ones that could be handled readily enough to yield experimental data. Silver oxide was used in preference to silver because it is readily available in a very finely divided form and because the presence of excess oxygen in the silver is important to the properties2 of the material. The powders were mixed wet, using alcohol as the medium, in an ordinary food blender until a uniform mixture was obtained. They were then dried and heated to reduce the silver oxide to silver. Only a fraction of the finely divided silver remains unoxi-dized upon removal from the oven since the finest particles of silver oxidize immediately upon contact with air. The remaining fine silver served as a binder during pressing. The mixture was then pressed at 20 tons per sq in. into shoulder-grip (reduced section 1/4 in. by l/4 in. by 1 1/4 in.) and rectangular bar specimens (l/4 in. by 1/4 in. by 2 in.). The green specimens were heated very rapidly in a globar furnace to 1000°C, held at temperature untic they had reached theoretical density and then furnace cooled. The strength of the two compositions at temperatures above 960 °C was determined by pulling shoulder grip specimens inside a furnace mounted on a tensile machine. Specimens were gripped by means of wires wrapped around the shoulders of the specimen. Temperatures were measured by means of a chro-mel-alumel thermo-couple placed in the vicinity of the specimen. Control of temperature (within ±°15C) was accomplished by means of a Weston Recorder-Controller. Before loading, specimens were held at temperature for approximately 15 min in order to insure uniform specimen temperature. The low loads were measured by a special load cell designed by Baldwin Lima Hamilton. All testing was performed on a FGT testing machine of the same com-pany. Creep studies were performed in bending utilizing rectangular specimens of the 20 pct alumina alloy. Specimens supported at both ends by knife edges of inconel were placed in a globar furnace, heated quickly to temperature, and the deflection of the beam measured optically as a function of time. The weight and size of the specimen were predetermined and the maximum stress on the beam calculated from

Jan 1, 1962

By R. R. Sayers

THE South African Mining and Engineering Journal recently pointed out that no satisfactory solution of the question of compensation for silicosis can be arrived at by placing further liability of an inequitable nature upon the mines. There are at present 35 scheduled mines liable to contribute to the annual levy of $800,000 and provide for the net outstanding liability of $6,400,000. Several of these mines have, as yet, not been able to set aside sufficient funds against their out- standing liability to the Compensation Fund. The gold producers declare that the gold mining industry today is passing its zenith, and that the production of gold will decline, with a consequent lessening of the spending power of the mines, which in about ten years will be reduced to a great extent unless encouragement is given for the opening of new mines. It is during this period of decline that the mines will be required to meet the large burden already created by miners' phthisis. In England the Workmen's Compensation Act, 1925, was extended to industries involving exposure to asbestos dust.

Jan 1, 1931

Jan 1, 1965

By M. E. Straumanis, J. -P. Krumme

In basic ([KOH + KCl] with a total polarity of 2) or acidic (2N H2SO4) electrolytes and at anodic current densities of more thun 2 to 4 ma per sq cnz, n-type GaAs single crystals of lozo resistivity preferentially dissol~je forming etch tunnels with triangular or civc~ilay cross sections and of a width between 0.5 arid 5 p. These etch tunnels are oriented along any one of the four possible (111) directions of GaAs. However, their growth occurs only in one direction of a given (111) whick apparently is determined by the atomic sequence Ga —As (and not the rezlerse) in respect to an individual valence bridge in the crystal. It is concluded from comparison with the cubic lattice structure of GaAs that the etch tunnels represent macroscopic evidence for the tetrahedral bonds and their polar properties. If the anodic current density is increased the tunnel fomation results in the development of a fibrous surface layer consisting of GaAs. The latter separates frorn the substrate (in an anodic s~irface disintegration process) by the growth pressure of an As,0, filnz forming in the interior of the fibrous layer, 100 to 200 µ under the surface, at more than about 50 ma per sq cni. The fibrous GaAs film has the same crystallographic orientation as the substvate and represents a skeleton of the original crystal. Since the etch-tunnel density in a separated GaAs layer is about 108 c?n-', and the etch tunnels develop only along (111) in a given polar direction, it is assurraed tlmt the dislocations have no influence on the growth of these tunnels. ElECTROLYTIC treatment of smooth surfaces of poly- and single-crystalline GaAs at high anodic current densities causes the formation of porous surface layers.' This phenomenon suggests comparison with effects being observed with magnesium,' indium,, gallium,4 and aluminum5 and known as "anodic disintegration". The purpose of the present paper is to explore and to explain the reasons for the formation of such surface layers on GaAs and, in particular, to investigate the influence of the lattice polarity of this III-V compound semiconductor in the (111) direction on the anodic dissolution behavior. GaAs SINGLE CRYSTALS For the experiments described below GaAs single crystals from the Monsanto Co., St. Louis, Mo., were used. Their impurity levels were below 1 ppm and their dopant levels between 1 and 100 ppm. They were grown in (111) using the Czochralski or the gradient-freeze technique. The crystals had n-type conductivity and electric resistivities between 1 and 5 ohm-cm. EXPERIMENTAL The GaAs single-crystal rods were cut perpendicularly to (111) into wafers of about 1 mm thickness using a wire-blade crystal slicer and an aqueous slurry of Sic or a diamond saw. The orientation of the faces of these wafers were checked by Laue back-reflection patterns. If there was a deviation from (111) the faces were abraded under a certain angle using grinding paper and distilled water. The damaged surface layer was removed from each crystal by chemical etching with a mixture of 1HF:1HNO3: 1H20 or 2HF:1HNO3:2HAc (glacial). {110) faces were obtained by mechanical cleavage, producing surfaces which did not require a further treatment. The GaAs wafers were mounted using "alligator" clamps instead of soldered electrical contacts.' Only the bare crystal surfaces were dipped into the electrolyte. The clamps were coated with insulating wax to prevent any contact with the electrolyte. The experiments were carried out in aqueous 2 N H2so4,' or in an aqueous solution of KOH and KCl1 (1 mole KOH + 1 mole KCl in 1000 cu cm solution). Anodic current densities up to several hundred ma per sq cm were applied for periods between 30 sec and 2 hr. For the purpose of investigating the initial steps of disintegration the anodic current density applied never exceeded 20 ma per sq cm. The films which partially separated from the anodic surfaces under high-field conditions were treated with KOH to further their detachment by dissolving the As2O3 formed. The washed and dried films were pasted to strips of filter paper, and Laue pictures were made. The back-reflection patterns obtained were compared with those of the original anode surface before and after anodic dissolution. Furthermore, space reciprocal lattices7 were constructed from asymmetric rotation crystal patternsa which permitted the determination of the crystallographic orientation of the detached films of the corrugated anodic surfaces. The disintegration products were identified from assymmetric powder patterns.8 The polarity of the {111) faces was determined by chemical etching with mixtures of 1HF:1H2O2(30 pct): 2H2O or 1HNO3:2H2O. Different patterns on each of two inverse (111) sides appeared.'-l8 The correlation of these patterns to the Ga{111) or the As(111) side has already been established by the use of light figures,18-20 by X-ray diffraction near the absorption edges of gallium and arsenic,'lmZ4 and by LEED measurements.25 The geometric structure of these surfaces and the interior of the anodically attacked crystals were observed and photographed with a high-power microscope using oil immersion objectives up to magnification of X1720.

Jan 1, 1968

By Alan Arias

On grinding in pure water, zirconium, tantalum, iron, and stainless-steel powders were extensively comminuted and simultaneously oxidized with hydrogen release, whereas nickel, copper, and silver powders did not react with water and their particle sizes increased. On grinding nickel, copper, and silver in water pressurized with oxygen, nickel and copper became extensively comminuted and were oxidized, whereas silver did not react with oxygen and its particle size increased. From these results and other considerations , it is hypothesized that for extensive comminution of ductile metals and alloys to occur on grinding they must react with the grinding media. UlTRAFINE metal and alloy powders are finding an ever-growing number of applications in metallurgy and in other fields.' Of particular interest are ultrafine metal and alloy powders suitable for dispersion strengthening.2'9 Various research programs on dispersion strengthening are being carried out and in some of these programs the ball-milling method is being used to produce dispersion-strengthened materials. This method usually involves the simultaneous grinding of metal or alloy and a dispersoid followed by consolidation of the resulting powder mixture. To obtain the ultrafine powders required for dispersion strengthening,' grinding is carried out in many liquids, including aqueous and nonaqueous media, with or without grinding aids.4'5 Nonaqueous liquids usually contain water as an impurity and some grinding aids may contain water of hydration.5 The water present may affect the grinding process. The writer has shown5 that. on ball milling chromium in water, the chromium is oxidized and hydrogen is released. It was surmised that the same reaction may occur on ball milling other metals and alloys in waterbearing liquids. Therefore, the investigation of ball milling in water was extended to metals and alloys other than chromium. In the course of the investigation, however, it became apparent that the data-to-gether with the results from a few additional experi-ments—could be used to postulate a comminution mechanism for ductile metals and alloys. A well-known comminution theory is that of smekal.7 According to this theory, comminution is possible because of the weakening effects of surface cracks and other imperfections in materials. This theory imposes a lower limit of about 1 µm for the ground particles. The beneficial effects of liquids and additives on the rate of grinding are well known.8 Mechanisms by which liquids and additives may aid in grinding were reviewed by Rose and Sullivan.' One aspect of these effects is based on Rehbinder's theory of crack propagation in materials under stress.9 According to Reh-binder's theory, liquids or additives may promote the spread of cracks in stressed materials by lowering the surface tension at the crack tip. Rose and Sullivan surmise that the same mechanism may be operative during grinding, thereby facilitating comminution of the particles. In addition, Rose and Sullivan reviewed how additives may act as dispersants as a result of their being adsorbed on the surface of the particles being ground. This concept has been suggested by Quatinetz, Schafer, and smea15 to explain from their experiments the major role of additives that enabled them to grind metal down to 0.1 µm. Discussions of other comminution theories and additional sources of material on the subject will be found in Ref. 10. None of these previous suggestions and theories, however, can account for all phenomena encountered during ball milling of metals to submicron size in this and in a previous investigation by the author.6 The objectives of this investigation were to determine the behavior of metal powders during ball milling either in pure water or in oxygenated water and to gain an insight into the grinding mechanism. Zirconium, tantalum, iron, nickel, copper, and silver powders were ball-milled in pure water. These metals were selected because their oxides cover a wide range of free energies of formation. For comparison purposes, an alloy-type 430 stainless steel-was also ball-milled in pure water. The pressure of the hydrogen released during ball milling was monitored in order to determine the oxygen that combined with the metal or alloy. In order to obtain more information on the nature of the grinding process, nickel, copper, and silver powders were also ball-milled in oxygenated water (water pressurized with oxygen). The oxygen that reacted with the powders was determined from the pressure decrease in the mills. The powders resulting from ball milling in pure water and in oxygenated water were subjected to surface area, optical microscopy, and X-ray diffraction analyses. With these data, the oxygen calculated to be combined with the metals during ball milling, and comparison of the free energies of formation of the oxides of the milled powders with that of water, a comminution mechanism was postulated. MATERIALS, EQUIPMENT, AND PROCEDURES The materials used in this investigation were powdered metals, deaerated distilled water, high-purity helium, and commercial grade (99.5 pct purity) oxygen. The powdered metals used were zirconium, tantalum, iron, nickel, copper, and silver. A 16 pct Cr, ferritic stainless steel, type 430, was also used. The purities (or nominal compositions) and the surface areas of these metals and the alloy are given in Table I.

Jan 1, 1970

By Thomas T., Read

ANY discussion of State-supported schools of mining and A metallurgy needs to be prefaced by a definition, since the first school to offer a mining curriculum, the Pennsylvania Polytechnic College, was established by a grant from the State. But, so far as can be determined, it received no further State support. It would be tiresome to go into precise details,. and it will be enough to stipulate that by State schools are meant those which derive their main financial support from regular appropriations made by a State legislature. The University of Michigan was the first of these to offer a mineral industry curriculum; its story, as well as those of Wisconsin and Illinois, has been related in the preceding chapter.* Arranging the others in chronological order involves making a decision as to what weight to attach to plans for giving instruction, as contrasted with its , effective initiation. This may appropriately be illustrated by the history of mineral industry education in California. California Among those who came to California in 1849 and the following years were many New Englanders who had a keen interest in education. Some of them, mostly Congregationalists and Presbyterians, sought to establish a school of higher education around San Francisco Bay and eventually succeeded in opening the "Scientific and Classical School at Contra Costa' in Oakland, at Broadway and 5th St., on June 20, 1853. This prospered so well that it was chartered by the State as the "College of California" on April, 13, 1855. Developing so rapidly that its quarters became cramped, in 1864 it not only bought a tract of

Jan 1, 1941

By Robert F. Mehl

THE solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstätten figures profusely nor with great ease. A study of the Widmanstätten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstätten figures.1 ALLOYS OF ALUMINUM WITH COPPER The most accurate determination f the solid solubility, of copper in aluminum seems to be that by Dix and Richardson,2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548°, and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solution on cooling tends to precipitate the compound CuAl2, and this conclusion has been confirmed experimentally by Schmid and Wassermann .3

Jan 1, 1932

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.' In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

By C. A. Stewart

PAGE. I. Introduction............ 241 II. Location. TopoGRaphy. and History....... 243 III. DescRiption of the Rocks......... 245 1. Altered Sediments.......... 245 2. Alaskite........... 246 3. Alaskite.Porphyry.....255 4. Quartz Dikes........... 257 5. Biotite.Granite.......... 256 6. Quartz.Porphyryl......... 260 7. Andesite........... 262 8. Miscellaneous Dikes......... 263 IV. Age oF the Rocks and Comparison with other Localities.. 263 V. AlteRation............ 265 1. Sericitization........... 265 2. Silicification........... 266 VI. StRuctuRes........267 1. Dip of the Limestone......... 267 2. Faulting........... 267 VII. Contact - metamorhism,.......... 269 1. Endomorphism.......... 269 2. Exomorphism......... 271 Recrystallization and Loss of Color...... 271 New ,Minerals.......... 272 Addition of Material........ 274 Volume.Changes.... 276 Locus of Metamorhism........ 277 Method of Precipitation.........278 VIII. ORe-Deposits............ 278 1. Contact-Metamorphic Copper.Ores,..... 279 General..........279 Shape and Distribution........ 279 Minerals........... 281 Secondary Enrichment........ 282 2. Disseminated Copper.Ores........ 283 3. Origin of the Copper.Orcs........ 284 4. Lead-Silver Ores.......... 287 IX. Bibliography............ 288

Jan 1, 1913

By Charles S. Barrett, Frederick N. Rhines, Robert F. Mehl

The solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstatten figures profusely nor with great ease. A study of the Widmanstatten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstatten figures.' Alloys of Aluminum with Copper The most accurate determination of the solid solubi1it.y of copper in aluminum seems to be that by Dix and Richardsoq2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548", and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solu-lion on cooling tends to precipitate the compound CuA12, and this conclusion has been confirmed experimentally by Schmid and Wassermann.

Jan 1, 1932

By L. S. Austin

I. Introduction............ 431 II. Organization............ 432 III. Production............ 434 IV. Transportation............ 435 V. Sampling..........436 VI. Concentration............ 440 VII. Blast-Furnace Plant........... 442 1. Construction........... 442 2. Operation............ 450 VIII. Advantages of Large Furnaces........ 455 1. Saving in Fuel........... 455 2. Saving in Jacket.Water..... 455 3. Quick and Large Discharge of Matte and Slag... 455 4. Decrease of Incrustation... 456 5. Elasticity of Operation..457 6. Large Flow Through Fore.Hearths...4. 57 7. Alterations Without Interruption..458 8. Variations in the Composition of Slag....458 9. Less Labor-Cost.......... 458 10. Less Initial Cost.......... 460 IX. Briquetting.Plant........... 460 X. Roasting-Plant............ 462 1. Kilns............ 462 2. Reverberatory Furnaces...468 XI. Converter-Plant........... 474 1. Construction ..........474 2. Operation.......... 476 XII. Flues and Stacks........... 478 XIII. Arsenic-Plant............ 480 XIV. Coke-Washing Plant.... 452 XV. Slime.Ponds ........... 483 XVI. Brick-Plant............ 484 I. Introduction. The Washoe plant; in Anaconda. Mont., together with the local street-railroad, ranches. a foundry and machine-shop. A

Jan 1, 1907

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of. Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By Per Kofstad, Hallstein Kjöllesdal

The oxidation behavior of niobium (columbium) has been studied in the temperature range 500° to 1200°C and at oxygen pressures of 760,100, 10, 1, and 0.1 mm of Hg. The work comprises kinetic studies of the oxidation as well as structural investigations of the oxidized specimens by means of X-ray diffraction, electron diffraclion, electron microscopy, and metal1ographic techniques. The oxidation reaction has a highly irregular temperature dependence and is unusually sensitive to changes in the oxygen pressure. The complex oxidation behavior is suggested to be due to formation of different Nb2O5 modifications in different temperature regions. During oxidation oxygen is also dissolved in the metal. Formation of oxide whiskers take place on the oxide surface at temperatures above approximately 800°C. VARIOUS aspects of the oxidation of niobium have been studied.l-12 The investigations show that niobium has a complex oxidation behavior, and the oxidation

Jan 1, 1962

By W. C. Elmore

THE magnetic powder method, long used for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations-of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1935

By William Kobbé

I. INTRODUCTION THE word recovery as used in this paper is applied in its broader sense and not limited to wells producing from horizons of unconsolidated sands. Certain problems connected with the winning of petroleum from such horizons present themselves while drilling is in progress and should be considered before drilling is commenced wherever unconsolidated sands are expected. Maximum recovery depends not alone upon efficient pumping methods but also upon the selection of a proper drilling system and the completion of a well especially adapted to the extraction of these oil-bearing sands. II. DRILLING DETERMINING FACTORS IN SELECTION OF METHOD The selection of a drilling method for the development of a region in which the oil reservoir consists of unconsolidated sands is based on the following considerations: (1) Character of the formations overlying the reservoir; (2) thickness of the oil-bearing stratum or strata; (3) thickness and character of water or gas sands; (4) gas pressure to be encountered or expected; (5) total depth of well.

Jan 12, 1916