Search Documents

By Arthur R. MacPherson

The development of a simple method to predict the autogenous grinding possibilities of new ore deposits is attained. This method employs a 45-cm (18-in.) dry grinding Aerofall mill to grind small quantities of core or crushed samples in the top size range of 2 to 5 cm (1 to 2 in.). An extensive program has been carried out to correlate the data obtained in the 45-cm (18- in.) test mill with the actual results obtained in large commercial plants or autogenous test plants. Enough evidence now exists from these correlation programs that the 45-cm (18-in.) mill can be used to grind small samples from a new deposit and correctly predict the autogenous grinding mill requirements of a commercial plant to treat this ore.

Jan 1, 1978

By Eugene A. Stephenson

In November, 1932, Dr. Lacey, of the California Institute of Technology, presented before the American Petroleum Institute some of the results of his research under Project 371. The investigations described dealt particularly with changes in the physical properties of petroleum that result from the solution of natural gas therein. The solubility of Santa Fe Springs dry gas, containing 87 per cent methane, 8 per cent ethane and 5 per cent propane, had been determined in various crudes at 100' F., and 2000 lb. pressure per square inch as shown in Table 1 and Fig. 1 herewith. Originally the computations were made in terms of cubic feet per barrel, but' for a more uniform basis of comparison the results are also shown as cubic feet of gas2 per cubic foot of oil.

Jan 1, 1935

By Desmond De Villiers Oxford, Peter H. Williams

Nchanga Consolidated Copper Mines, Ltd., is one of the four mines operated by the Anglo American Corp. in Northern Rhodesia, now the independent nation of Zambia. Today Nchanga is the second largest single producer of copper in the world, accounting for more than 200,000 long tons of copper annually at a monthly milling rate of 430,000 tons of ore. The average mill-head grade is about 5.20% total copper, of which approximately 60% is copper sulfide. The remainder, referred to as "acid soluble," is copper oxide. Nchanga mines three separate orebodies varying in grade and sulfide-to-oxide ratio. Ore is processed in two separate grinding circuits feeding into three separate flotation circuits. A fourth flotation circuit treats leach plant residue for additional recovery of sulfides.

Jan 1, 1965

By AIME

Generally speaking, the mining industry had a good year in 1948 with most mineral products being produced in record quantities for peacetime standards. The big boys-iron and steel, coal, and petroleum-indicated the industry-wide trend by surpassing 1947 production figures. Although exploration and expansion are being pushed aggressively in all branches of the industry, there is a pronounced trend to engineering and research directed at cutting production costs, improving the product, and finding new markets. These improvement campaigns are making headway; in the bituminous coal industry, 5.43 tons per man employed is the new production record; 83 million tons of iron ore were unloaded at lower Lake ports, breaking another peacetime record; magnesium, due to improvement in manufacturing techniques, now competes on the market with aluminum.

Jan 1, 1949

Mar. 3-7, ASTM, spring meeting and commitee week, Hotel Statler, Cleveland. Mar. 4, AIME, Morenci Sub-Section, Longfellow Inn, Morenci, Ariz. Mar. 5, AIME, Chicago Section, Ladies Night, Chicago. Mar. 10-13, National Electrical Mfrs. Assn., spring meeting, Chicago. Mar. 10-14, National Assn. of Corrosion En-Engineers, annual convention, Galveston. Mar. 11, Society for Applied Spectroscopy, 6 pm, supper, Tosca's; S pro, meeting, Socony-Vacuum Training Center, 63 Park Row, New York. Mar. 16-19, American Institute of. Chemical Engineers, Atlanta Biltmore Hotel, Atlanta. 'Mar. 17-21, ASTE, annual meeting, Chicago. Mar. 20, AIME, Philadelphia Section, Engineering Bldg., University of Pennsylvania, Philadelphia. Mar. 22-Apr. 6, Chicago International Trade Fair, Navy Pier, Chicago. Apr. 1, Society for Applied Spectroscopy, Socony-Vacuum Training Center, 63 Park Row, New York.

Jan 1, 1952

By A. T. Miesch, L. B. Riley

An error occurred in the preparation of Fig. 3, p. 249, of Basic Statistical Measures Used in Geo-chemical Investigations of Colorado Plateau Uranium Deposits. This figure shows the relation of the arithmetic mean: geometric mean ratio to the geometric deviation. Curves for the cases where n, the number of samples, is 100, 10, and 5 are too high with respect to the ordinate. The error is negligible at low geometric deviations, but becomes increasingly greater wi,th higher values of geometric deviation. Arithmetric mean values in Table I1 are not effected by the errors in Fig. 3. The authors will endeavor to supply copies of the revised curves on request; write to: A. T. Miesch, Geologist, Branch of Radioactive Materials, U.S. Geological Survey, Bldg. 25, Federal Center, Denver 25, Colo.

Jan 1, 1962

By G. E. Karantzavelos

A novel two-stage froth flotation process for the recovery of pure magnesite from low grade ores is described. The process consists of a first-stage, magnesite flotation step where a rougher magnesite concentrate is floated with amine collectors. The first-stage froth concentrate is then repulped in fresh water, and quartenary ammonium salt and fuel oil are added to float the remaining impurities. The results from laboratory batch tests show that a high-grade magnesite concentrate assaying 0.99-0.20% Si02 and 2.84-0.46%a Ca0 can be produced. Regulation of the variables controlling magnesite froth flotation also allows the variation of the ratio % Ca0: % SiO2, between the acceptable limits 0.32 to 5.79. This ratio is important to the quality of dead-burned magnesite.

Jan 1, 1985

By Thomas M. Plouf

Getting optimal performance from flotation cells can, in many cases, be critical to a project's economic viability. Simple testing procedures can sound early warning signals as well as maintain optimum recoveries from the flotation cycle. The materials required for a simple testing laboratory include: (1) pH meter or pH paper, (2) bottles of reagents used in plant flotation, (3) stop watch, (4) calibrated eye droppers. (5) laboratory flotation machine (1000-g tank, open impeller), (6) froth collection pans, (7) magnifying glass, (8) sizing screen sufficient to retain 10% of the flotation feed coarse fraction, (9) sizing screen for the size particles at which desliming of the plant flotation feed is to take place, and (10) a set of screens covering the complete range of feed particle size.

Jan 4, 1978

By A. P. Herring, M. Hoover, D. W. Fuerstenau

The dissolution of nickel, copper, and cobalt from five different samples of well-characterized deep sea manganese nodules was measured as a function of temperature, pH, leaching time, and particle size. Nickel, copper, and cobalt extraction each respond to these variables in a different manner. The results of this investigation indicate that copper and nickel can be selectively dissolved from iron and manganese at moderately low pH, provided the reaction is given sufficient time. A high dissolution of cobalt with dilute sulfuric acid can only be achieved from nodules that have a low iron content (<5%). The most probable rate-controlling step for copper and cobalt dissolution is diffusion through the pores of the nodules, and for nickel dissolution chemical reaction appears to be rate-controlling.

Jan 1, 1974

By F. G. Jaicks

RECOGNITION of the benefits to be gained from the continuous casting of molten steel into finished or semifinished products has been given by scientific minds since the very beginnings of steel plant technology. In fact, Sir Henry Bessemer is credited with the first of a long list of patents&apos; issued by the U. S. Patent Office for a process which would accomplish this desirable end. None of these early ideas attained practical success and, as a result, the conventional method of teeming into ingot molds became an integral part of modern steelmaking operations. This procedure, although refined to keep pace with the changes which have come about in steelmaking and finishing facilities, is recognized to have inherent shortcomings which adversely affect manufacturing costs and steel quality. Interest in the continuous casting of steel persists because the process is directed toward avoiding some obvious weaknesses of conventional ingot casting. It has been recognized that should it be possible to substitute any of the continuous casting techniques under current development for ingot casting, it would no longer be necessary to make large capital investments in primary rolling equipment, the sole purpose of which is to reduce ingot castings to a form rollable on finishing mills. The results reported in the continuous casting of non-ferrous metals and specialty steels indicate that in addition to avoiding the primary rolling mills there is some basis for expecting significant improvements in yield, surface, and internal quality. Recognizing the shortcomings of the conventional procedures, the Inland Steel Co., in cooperation with Atlas Steels Ltd. and the Freyn Dept. of the Kop- pers Co. Inc., embarked upon a program to evaluate certain aspects of continuous casting in order to determine whether the process could be applied practically to an existing integrated steel plant producing &apos;large tonnages of carbon steels. TO assist in this evaluation a study was carried out in which several types of low carbon steel were continuously cast in an existing machine. It is the purpose of this paper to review some of the results obtained in the casting studies and to interpret the information that was obtained so as to indicate factors that must be considered in assessing operating limitations and plant capacities. Despite the early interest in the continuous casting of steel, the actual application to the steel industry is relatively recent. At present, there are about 25 operating plants casting steel, most of which have been built in the past decade. None of these plants could be classified as large in terms of the tonnages that are being processed by the major integrated steel plants. In contrast to the situation in the steel industry, there has been widespread adoption of the continuous process in the casting of nonferrous alloys, particularly aluminum and copper. As a result, much of the basic information that was required to apply the process to steel was developed in the nonferrous industries. In this respect, a most important contribution was the development of the Junghans2 system, which was initially designed for the casting of nonferrous metals and later applied to the casting of steel. Alternative methods for casting have also been proposed by Babcock and Wilcox Tube Co.,&apos;" the British Iron and Steel Research Association,5 and the Gebruder Bohler A. G.13 Each of these methods is now being used successfully for the casting of special steels in small experimental plants or in modest sized commercial steelworks. The Original Junghans process was first developcd in Germany. Further application of the process has been made by Rossi in other countries.&apos;*&apos; The experi-

Jan 1, 1958

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By H. G. Schneider

The Smackover oil and gas field lies in Ouachita and Union Counties, Ark., in the south-central part of the state, in T.15 and 16S., R.15, 16, and 17W. It is 10 miles north of El Dorado, the principal business and railroad center in the south-central part of the state, and extends from the town of Smackover in all directions. Productive territory having an aggregate area of nearly 55 sq. mi. has been developed. It extends 6 miles from north to south and 12 miles from east to west. The field may be divided into two parts: the east district, which includes the area east of the town of Smackover, and the west district, which includes the area west of the town of Smackover. In relation to the neighboring productive fields of Arkansas, the Smackover field is 9 miles north of the El Dorado oil and gas field, 8 miles slightly west of north of the East El Dorado oil and gas field, and 16 miles east of the Stephens oil field. Smackover was discovered in May, 1922, when the Oil Operators Tnist drilled well No. 1 on the J. T. Murphy farm, in the southeast quarter of sec. 8, T.16S., R.15W. This well is located almost on the top of the Norphlet dome and was drilled to the Nacatoch sand. It had an initial open flow volume of 30,000,000 cu. ft. of dry gas per day, and a rock pressure of 950 lb. per sq. in. In July, 1922, the V. K. F. Co. completed the first oil well in sec. 29, T.l5S., R.l5W., on the north side of the Norphlet dome, and 3 miles north of the first gas well. This well started the active development of the north and northwest sides of the dome.] The field was extended westwards, when oil was discovered in the Nacatoch sand, during October, 1922, in sec. 4, T.l6S., R.l6W., 51/2 miles west of the original gas well. This opened up the so-called "light oil district," which is located on a structural terrace, for which the name

Jan 1, 1924

By T. A. Read, H. K. Birnbaum

STRESS-induced twin boundary motion in the AuCd ß&apos;phase (52.5 at. pct Au 47.5 at. pct Cd having an orthorhombic structure (space group D h)&apos; was discussed for the case of transformation twins.&apos; Mechanical twinning, i.e., introduction of new twin orientations by the applied stress was sometimes observed in the ß&apos; phase which contained two transformation twin orientations. (See Ref. 2 for experimental details.) The transformation twins terminated at the mechanical twin boundary; the two initial orientations having been twinned to the new orientation as shown in Fig. l. In a "hard" tensile instrument, formation of each mechanical twin was accompanied by a sharp drop in load (and an audible click) resulting in a typical serrated load-extension curve. The mechanical twins increased in width and additional twins were nucleated as the load increased until the entire specimen was occupied by the mechanical twin orientation. A restoring force2 caused the mechanical twin and transformation twin boundaries to return towards their initial configuration on releasing the load. In a stabilized specimen* the total strain introduced by mechanical twinning was recovered on releasing the applied stress. Initial and final microstructures were identical. After decreasing gradually to a critical width, mechanical twins suddenly disappeared accompanied by audible clicks and sharp increases in load (measured at a constant rate of crosshead motion in a "hard" machine). Mechanical twins could be stabilized in any position by maintaining the applied load for a sufficient time, indicating a decrease in restoring force with time similar to that observed for transformation twins.&apos; Orientation relationships for mechanical and transformation twins were determined and are shown in Fig. 2. The mechanical twin, T3, was twin related to transformation twin, T,, by reflection in (1ll), and twin related to transformation twin, T2, by reflection in (111)T, . T, was related to T, by reflection in(ll1)T1 . The "average" mechanical twin composition plane lay several degrees from (1ll), . In every specimen which mechanically twinned, orientation T3 was most highly favored by the applied stress, i.e., it was the twin orientation which provided the greatest change in length compatible with the direction of applied stress

Jan 1, 1961

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions&apos; the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures&apos; When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By S. W. Nabbs, W. D. Bachman, A. W. Last

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from. Kennecott Copper Corp.&apos;s Chino mine. The grindability of the various samples was found to vary over an extremely wide range, even among samples taken from diflerent locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale nonhomogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully. In the past 15 years, comminution by primary autogenous grinding has been investigated and applied economically in the minerals industry, particularly in iron-ore processing. Successful application of primary grinding is described by A. A. Dor,l.&apos; P. B. Dettmer,334 R. R. Turner, and W. F. McDermott." other authors describing the advantages of primary grinding include H. Hardinge,&apos; R. T. Hukki,&apos; D. S. Coyle" and F. C. Bond,"," to mention only a few. For the past several years, Kennecott Copper Corp.&apos;s Metal Mining Div. Research Center has been investigating primary grinding of disseminated copper ores. Both fully autogenous and semi-autogenous grinding has been explored. Ores from three of Kennecott&apos;s western operating properties and from several development properties have been tested. Host rocks include diabase, schist, silicated and argillaceous limestones, shale, granite porphyry, quartzite, and granodiorite. The object of this paper is to supplement the general knowledge in the field of primary grinding by presenting information gained from the studies with the various disseminated copper ores. Data are presented which show that carefully considered test programs are required to determine the practicality of applying autogenous grinding to a specific mining-beneficiation operation. Particularly this is so if more than one rock type occurs within an ore body or if there are wide variations in the degree of rock alteration within a deposit. Extensive sampling and subsequent testing of the ores within a mine are required if serious pitfalls are to be avoided and good engineering data acquired. We hope that this presentation will stimulate studies to increase the understanding of the fracturing process applicable to large pieces of rock, a factor which is important in autogenous grinding. Test Facilities and Procedures Both pilot-scale and full-scale test facilities were used to investigate primary grinding characteristics of the disseminated copper ores. A 6-ft Hardinge Cascade mill, a 24-ft Hardinge Cascade mill, and a 5-ft Aerofall mill were used in the studies. The Cascade mills were operated wet, while the Aerofall mill was operated both wet and dry. The Cascade mills were operated both for fully autogenous and for semi-autogenous grinding; the Aerofall mill was operated only semi-autogenously. Fully autogenous grinding, as the term is used in this presentation, is defined as the direct grinding of coarsely crushed rock by the action of the rock mass. Semi-autogenous grinding is defined as the grinding of coarsely crushed rock with the rock mass supplemented by a steel ball charge. Most of the test work was done using the 6-ft Cascade mill, operated under fully autogenous grinding conditions. Only limited testing was conducted with the 5-ft Aerofall mill and only one ore was tested using the 24-ft Cascade mill. This presentation is concerned, therefore, primarily with fully autogenous, pilot-scale grinding in the Cascade mill. Fig. 1 presents a diagram of the test facilities used with the 6-ft Cascade mill. Principal test equipment consists of a 6-ft Cascade mill, an 18-in. spiral classifier, an elevator, a 2 x 9-ft belt feeder, a conventional integrating kilowatt-hour meter, and a recording wattmeter. In testing, feed charges, adjusted as to weight, were deposited as evenly as possible on the belt feeder every 15 min. The weight of each charge was adjusted to maintain a mill charge of 27 to 30% of mill volume. The classifier was adjusted to obtain the desired size-consist of the final product, generally at 20% + 100 mesh. After equilibrium was established in the circuit, the feed, mill discharge, classifier sand, and classifier overflow were sampled and their size distributions determined. During the sampling periods, the power drawn by the mill was measured to determine the energy consumed in the reduction of the size consist of the ore solids. Fully Autogenous Pilot Grinding Tests on Various Kennecott Ores Typical test results obtained in the 6-ft Cascade mill with samples from Kennecott&apos;s Ray Mines Div., Chino Mines Div., Utah Copper Div., and a development property designated as Mine A are presented in Table 1. As shown, the ores that were ground most easily in the pilot-scale mill were composite mine samples obtained

Jan 1, 1971

By R. F. Yap, N. Arbiter, C. C. Harris

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give substantially constant power numbers in liquid systems indicating that they operate close to fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufacturers. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles, drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations. The modern mechanical flotation machine has, over a period of 60 years, displaced other designs to become the dominant type. Once the correct chemical environmental conditions have been established, the major requirement, selective mineral-air adherence, is essentially a function of two operating variables — impeller speed and air rate. The special nature of this dependence is such that in the same apparatus, but under different operating conditions, adherence can be either prevented or destroyed. Another aspect of this observation is that flotation machines though differing in detail to a considerable extent can produce similar metallurgical results. It must be concluded that having determined the correct reagent levels, establishing the correct operating conditions are at least as important as machine design. Since about 1960, after 30 years of fairly stable circumstances, manufacturers have been developing new types of machines whose major feature is emphasis on pulp flow characteristics by virtue of new im-peller-stator designs. As far as can be ascertained, these new designs necessitate radical departures from accepted impeller speed-air rate values. Performance data are still awaited. Flotation machine development has been empirical, as is selection of operating conditions. The purpose of the work at Columbia University has been to elucidate the fundamentals of the subject so that the purely mechanical aspects of the flotation process can be understood in hydrodynamic terms.1-6 Hopefully, this might lead to intelligent selection of a particular machine and its operating conditions for a specific ore based on a minimum of testing, or even to new types of flotation machines. The present investigation is the most comprehensive to date.7,8 Earlier work, which was largely exploratory, has been repeated and extended and employes the most accurate measuring techniques available. Additionally, sufficient hydrodynamic data were obtained under flotation conditions to delineate the relevant operating ranges. Attention has been given to scaling in that several geometrically scaled tanks and impellers have been constructed and tested; it has been pointed out elsewhere that undistorted geometrical scaling rarely pertains in flotation machine design.5 This paper is divided into sections dealing with relevant combinations of the three phases: liquid, air and solid. Summaries of the literature have been given in previous publications2-4 and will not be repeated here. Recently, several reviews of mixing have appeared, which can be usefully referenced.9-11 It is of interest to note that flotation is not included

Jan 1, 1970

By F. G. Smith

A few years ago, the writer encountered a problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Mathewson and Phillipsll an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-mm. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures. Preparation of Specimens The material used was cartridge brass 0.400 in. thick, having the following composition: Copper 66.60 per. cent., zinc 33.35 per cent., lead 0.02 per cent., iron 0.03 per cent. This was rolled with 35 per cent. reduction after a 700" C. anneal. Fig. 1 shows the structure of this original bar on which all subsequent anneals were made. Pieces 1 in. (2.5 cm.) wide and 3 in. long were prepared and annealed for 1/2 hr. at 450°, 550°, 650°, &apos;750°, and 850" C. Each of these pieces are indented under the Brinell test with a 10-mm. ball at 500, 1000, 2000, and 3000 kg. pressure. Then, sets of five pieces from each of the original anneals were reannealed at 450°, 550°, 650°, 750°, and 850" C.

Jan 1, 1921

By Eduardo J. Chibas

Location.—The principal manganese-deposits of the Department of Panama, Republic of Colombia, are located almost clue south of Viento Frio, a native village bordering on the Caribbean Sea, and about 45 miles northeast of Colon (Aspinwall). The mining-claims are the Viento Frio, the Carrano, the Nispero, and the Soledad. Each property is to the south of the preceding one in the order mentioned. The first one is about one mile from the coast, and the most southerly boundary of the Soledad is about five miles in a straight line from the same coast-line. I shall confine my remarks to the four properties mentioned and to La Guaca, west of the Carrano, because these are the only ones where mining has so far been done to more or less extent. Manganese has also been found, however, in the neighborhood of these deposits, and a large area adjoining them has been divided into sections and " denounced " as mining-claims. The relative position of the manganese-deposits and Nombre de Dios, the present terminal of the railroad and shipping-port, as well as Viento Frio and the adjacent coast, can

Jan 1, 1898

Jan 1, 1951

Jan 1, 1951