Search Documents

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By Rizo-Pairón Alfonso, A. M. Gaudin

PREVIOUS studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector The results obtained indicate that a I I ratio of collector ion to activator ion gives optimum results, and that a 2 I ratio almost fails to achieve activation and flotation Yet, a 2 I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids, they confirm that an adsorbed coating is inescapable APPARATUS AND SUPPLIES The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz The flotation machine was built according to the design of D W McGlashan It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel stator, as in the Fagergren laboratory machine The air intake is controlled by a valve, and the cell consists of a beaker The quartz was obtained from vein quartz stored in large chunks It was first crushed to 20 mesh, then sized on a 28-mesh screen The 20 to 28-mesh size alone was retained for use This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used The barium was used as barium chloride, Baker's analyzed C P The oleate was used as sodium oleate It was prepared from sodium hydroxide, Baker's analyzed C P , and oleic acid purified by R R de Arellano3 in the laboratories at the Massachusetts Institute of Technology The purification procedure was elaborated from the recent researches of Brown and Shinowara 2 It consisted in (I) saponification of olive oil with potassium

Jan 1, 1942

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By D. H. Polonis, M. B. Kasen

AN unusual thermal etching phenomenon has been observed on the surface of a Cu-Si alloy. The observations were made during studies of vacancy condensation pit formation which were reported in previous papers.1,2 Figs. 1 and 2 are photomicrographs of the surface of a Cu-4.8 pct Si alloy after heating in vacuo (3 x X mm Hg) to 525°C and subsequently holding at that temperature for 16 hr in an impure (air-contaminated) argon atmosphere. Under these conditions preferential removal of silicon from the matrix by oxidation results in a surface which is entirely a phase overlying an a plus y structure. The light areas of Fig. 1 are regions in which very little thermal etching has occurred, while the majority of the surface has experienced severe etching. Similar regions in Fig. 2 are seen as plateaus above contours produced by net transfer of material from the specimen surface. Twin boundaries are also visible in Fig. 2. The difference in matrix mi-crostructure between Figs. l and 2 reflects the par- ticular orientation of low-index planes with respect to the surface of observation. Thermal etching contours of this type have been studied in detail by Hondros and Moore Both of the photomicrographs show that one or more dark spots are located approximately at the center of every protected area; where two spots are in close proximity, the protected areas have merged. The microstructures indicate that the anomalous resistance to thermal etching is related to the presence of these spots. Williams and Hayfield have shown that local regions of unusually high oxidation resistance can be caused by a surface monolayer of atoms with a work function higher than that of the base material. The result is an inhibition of the rate of electron removal from the base material and a decrease in the oxidation rate. The source of the protected layer may be either surface diffusion from contaminants on the specimen surface or pipe diffusion of solute atoms followed by migration across the surface. In the latter case the driving force is a difference in chemical potential resulting in a Gibbs adsorption phenomenon. In the present case, chemical polishing of the specimen surface precluded contaminants of a strictly surface nature. Consequently, diffusion of impurity atoms from within the lattice appears to be the most tenable explanation of the observed phenomena. The authors propose that the structures of Figs. 1 and 2 reflect the diffusion of impurity atoms along extended dislocations within the individual a phase grains prior to surface oxidation. The central spots within the protected regions are seen as sites of dislocation emergence which have become locally decorated with oxide in the manner discussed in Ref. 1. Williams and Hayfield observed protected regions adjacent to the grain boundaries of iron-contaminated copper which they attributed to the segregation of iron to the grain boundaries coupled with high dif-fusivity along the complex dislocation array at such boundaries. No evidence of such grain boundary protection was observed in the Cu-Si alloy; this

Jan 1, 1964

By Norman Pilling

THE solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are. not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion.

Jan 1, 1929

By Raymond Wilson

Grinding costs are an important item in cement manufacture, and the cost of power is one of the large items in grinding costs. Even where power is of secondary importance, cost items dependent on mill capacity are influenced by the efficiency with which the mill uses power. Tube mills typify the grinding mills most generally used in cement plants, though other types are in use. Tube mills have been widely criticized as being extremely inefficient, and this feeling regarding them has led to many attempts to design more efficient grinding equipment. Other types may be an improvement over tube mills, but the improvement has certainly not been revolutionatry, at least as applied to clinker grinding. The very fact that there is doubt regarding the relative efficacy of various types of mills is an indication that an adequate basis for an analysis of performance is lacking. The development of methods of analyzing mill performance has been hampered by the lack of a suitable method for measuring the work actually done in pulverizing. There has been no acceptable standard to which mill performance might be compared. As a consequence, it was not known whether the margin of possible improvement in pulverizing operations was large or small. Even direct comparison of different types of mills was seldom possible because most plants had only one type of mill for each type of service. Comparisons between plants were difficult because of differences in the grinding characteristics of various clinkers. Some recent developments complete a chain of circumstances that place the cement industry in a particularly fortunate position for the study of its clinker-pulverizing operations. Modern investigators of grinding phenomena have generally agreed that the best measure of mill performance is the production of new surface. For most materials this measure of performance is largely theoretical and has a rather remote connection with the practical aims of the grinding operation. In clinker grinding, on the other hand, surface area is intimately connected with the properties conferred on the cement by grinding. Morcover, the determination of surface area is rapidly coming into routine use as a tost

Jan 1, 1938

By M. H. Richman, E. S. Meieran

An analytical method is presented which enables the electron diffraction patterns from a twinned region to be indexed. The method has only been applied to (112) twins in bcc lattices, but can easily be adapted to other types of twinned lattices. Calculations of all twin spots, including those superimposed on matrix spots, is made possible by this method. SINCE the advent of transmission electron microscopy, the analysis of selected-area electron diffraction patterns has become very important in the interpretation of electron micrographs. Frequently, as in the case of some martensites, twinned areas are observed and give rise to complex diffraction patterns, which so far can be analyzed only for the simplest orientations of the thin foil specimen with respect to the electron beam. In order to simplify the analysis of twin patterns of more complex orientations, an analytical method was devised which is capable of predicting the positions of all reflections from both matrix and twin regions for all possible foil orientations. Although the method has only been applied to the case of bcc metals twinned about a (112) plane, it is equally applicable to other Bravais lattices. This method has been successfully applied to selected-area electron diffraction patterns of Fe-Ni and Fe-Ni-C martensites and drawn tungsten wire. PROCEDURE Imagine the reciprocal lattice corresponding to a bcc material, with each point hkl representing the crystallographic plane (hkl). Since the extinction conditions require that for this lattice, only reflections where h + k + 1 = even integer are allowed, the three dimensional reciprocal lattice is actually fcc. Since in real space twinned regions and matrix regions are mirrored across a (112) plane, the twinned reciprocal lattice is derived from the matrix reciprocal lattice by a rotation of 180 deg about a (112) direction. While it is possible to calculate how a point hkl will shift under a twinning transformation to a new point htktlt using only the reciprocal lattice based on the orthonormal vectors [100], [010], and [001], the calculations are greatly simplified if a new orthonormal coordinate system containing the twin axis is introduced. The twinning operation then becomes a simple rotation of 180 deg about a principal coordinate axis (in this case the twinning axis), and a retransformation back to the original reciprocal space will give the position htktIt of the twinned reflection.

Jan 1, 1963

By David V. Ragone, Richard E. Balzhiser

The liquidus uranium concentration in the U-Bi system is given by the following expression for the temperature range 400° to 800°C: No break was observed in the curve over this temperature range. The partial molar enthalpy change for uranium in the liquidus reaction, UBi2— U + 2Bi, was found to equal 12,300 cal per g mole. Copper produced a continuous decrease in the liguihs uranium concentration at 600°C. The presence of copper in the solvent was observed to affect the uranium activity coefficient according to the following expression: duced no change in the liquidus combosition below 0.6 at. pct Pd. Higher palladium concentrations sharply depressed the uranium concentration. SOLUTE behavior in molten alloys has been shown to be strongly influenced by the presence of additional species. Much attention has been given to such phenomena in iron-base systems where a number of alloying elements and/or impurities are likely to be present in small but significant quantities. Frequently, the interaction of these solutes has altered their thermodynamic behavior to the extent that reaction equilibra are appreciably influenced. Consequently, much of the information available for binary behavior must be reevaluated when additional components are likely to be present. Similar interactions can be expected to occur in bismuth-base solvents. Interest in the use of bismuth solutions of uranium as reactor fuels has stimulated investigators to explore the effect of various elements on the liquidus uranium concentration. Criticality requirements necessitate close control of the uranium concentration which, at the anticipated operating temperature of 500°C, approaches saturation. Consequently, elements which suppress the liquidus concentration could produce serious reactivity problems. Since the fuel solution is cer- tain to contain additives, such as magnesium and zirconium, for corrosion inhibition as well as small concentrations of fission products and corrosion products, a better understanding of the possible interaction phenomena is mandatory. This need stimulated experimental programs at the Brookhaven National Laboratory and elsewhere to determine precisely the liquidus uranium concentration in the bismuth-rich portion of several ternary systems. Early experimental efforts were directed toward an accurate dcmtermination of the U-Bi liquidus over the temperature range from 300' to 800°c. As shown in Fig. 1, the results to date exhibit considerable scatter. The investigations of Bareis,' Teitel,2 Greenwood,3 and Cotterill and hon4 agreed well below 700°c. Greenwood and Teitel extended their studies to higher temperatures but failed to concur in their results. A more recent study by Schweitzer and weekss at Brookhaven National Laboratory between 300' and 725°c, produced values 15 pct lower

Jan 1, 1962

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust- collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market out- lets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk so-ton lots direct to the consumer. POTENTIAL MARKETS FOR FINE- MESH COAL DUST In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, “sea coal” distributing plants, water-purification plants and obviously, pow-

Jan 1, 1944

By L. D. Anderson

WHEN, after years of troublous experiences in roasting sulfide ores with heavy dust and fume losses resulting from the equipment and methods first available, there appeared on the, scene of metallurgy that revolutionary process known as sintering, it was felt that at last there had been found the ideal method for preparing sulfide ores for blast-furnace reduction. Not only were the sulfides roasted but also the fine oxidized ores were bound together with them in strong porous cellular masses which were in the best possible condition for reduction. With the experiences gained in the manipulation of the Huntington-Heberlein, Carmichael-Bradford, and Dwight & Lloyd processes there developed a refinement of detail which brought the whole plan of roasting by sintering to a high plane of perfection. But that metallurgy is never stationary is revealed by the fact that changes in milling practice, particularly the development of flotation, have introduced a new set of problems in sintering itself. Inasmuch as it is felt that these problems have not yet been solved in an entirely satisfactory manner this paper is written to record the present practice of the Salt Lake Valley smelters with the hope that there will be brought forth such discussion as may perhaps lead to still better practice. By far the greater proportion of the sulfides smelted today are flotation concentrates. Usually they are high grade, sometimes as high as 70 per cent. and more in lead. They are extremely fine, many mills grinding the ore so that from 60 to 80 per cent. will pass through screens of 200 mesh. The physical condition in which many of these concentrates reach the smelters is disconcerting to the metallurgists. Some are of about the consistency of putty. Others are of a sticky, slimy nature. Others again, dried to the limit, are veritable powders. Remembering that the down-draft sintering charge for the best results must be porous enough to let air be drawn through it reasonably well, must be thoroughly mixed, and must have some coarse material in it to segregate out and form a layer on the grates, it will be understood that the advent of this extremely fine material has made necessary still further elaboration in the equipment and processes of preparing sulfides for the blast furnaces, all of which is expensive. The high metal contents of the concentrates

Jan 1, 1929

By J. L. Gillson

Andre Hubaux: In the writer's opinion, more stress should be put on field and microscope observations, as J. L. Gillson does. His discovery of relics of big labra-dorite feldspars from the Marcy anorthosite in all the other rocks is proof enough that previous field observations have been inadequate. The writer's field experience with anorthositie massifs is limited to the Egersund-Sogndal district in southern Norway; however, this is a very large and well exposed area. It seems to have so many points in common with the Adirondack region that a detailed comparison should be beneficial. This comparison was not possible 20 years ago, owing to the scarcity of geological data, at least for Norway. Both regions are now far better known—the Norway district because of the work of Professors Bugge and Barth 33-35 and especially because of the extensive field and microscopic research of P. Michot,30-35 who introduced me in the field to the problems of that region. In a particular unit of the Egersund district, a sodi-fication of the plagioclase, very similar to what Gillson calls "andesinization," has taken place. 12' The percentage of anorthite in the plagioclase has dropped from 42 to 43 pct in the original norite down to 27 pct, but never below that level. This metasomatical transformation is a part of a whole series of processes of mig-matitization which have produced, above the level of granitization, concentrations of Mg, Fe, and Ti and among them, patches and parallel bands of ilmenite and magnetite. Thus both regions present somewhat comparable features and the theories to explain them have several points in common. However, as there seem to be differences between some American conceptions and the views commonly accepted at the University of Liege, I would like to make some comments about J. L. Gill-son's article. The author speaks of the garnet as being an anti-stress mineral. However, garnet may be found in schists, where its helicitic texture, when present, demonstrates its formation during differential movement. Furthermore, the whole concept of stress and anti-

Jan 1, 1959

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By Arthur Phillips, E. N. Skinner

DURING the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson1 who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.015 per cent at 1050°C. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000°C. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hewitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of minute concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicroscopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By H. V. Winchell

An examination of the Pachucal and El Oro districts in July, 1920, although cursory and incomplete, disclosed facts of more than passing interest to the student of ore deposits; and inasmuch as the literature on these districts is limited and some of their features are little understood, a brief account may prove valuable as reconnaissance observations to be amplified by more thorough and competent observers in the future. Where no complete monograph of important mining camps has been published a partial presentation of the data is often useful, as it sometimes leads to fuller and more accurate descriptions, by stimulating discussion. The following notes are presented with the consent of A. F. Main, managing director of the El Oro Mining and Railway Co., whose fund of information and wide acquaintance with both districts alone made it possible to cover so much ground in a short time. I have also to acknowledge gratefully the aid of C. A. Lantz and D. S. Calland of the Santa Gertrudis and Real del Monte companies, respectively, in connection with permission to inspect geological features of interest in their mines. Pachuca, Hidalgo, Mex. This mining camp has been described by Ezequiel Ordonez2 and by A. F. J. Bordeaux.3 Reported to have been discovered in 1522, it has produced silver valued at between $250,000,000 and $375,000,000. Subsequent to the discovery here, by B. de Medina, of the patio process. in 1557, its production was increased, and now, using cyanidation, the output of the camp is nearly one-sixth of the production of the world. Topography and Climate The Pachuca district consists of a series of mountains and valleys, the minor features of which extend in an easterly and westerly direction and reach elevations of 8000 to 10,000 ft. (2438 to 3048 m.) above the

Jan 1, 1922

By J. R. Cain

ROLE OF GASES IN FERROUS -METALLURGICAL PROCESSES IN every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sieverts1 has shown that molten metals require but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon manganese or

Jan 8, 1919

By A. J. Bartlett

Island Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, arid all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly arid continuously; that is, at all times while the mine!: are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are contacted in their working places and other employees at their respective, work. A thorough check is made to see that the state mining laws are complied with and that company safety rules arc being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emergency nature are taken up immediately with the management. Periodical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipmcnt and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture of the existing conditions at the time of inspection. Copies of inspection reports are forwarded to the superintendents with the general manager'? comments. It has been said, "There is nothing under God's heaven that justifies. your creation or your citizenship but this gospel: ' That the next greatest

Jan 1, 1938

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By J. M. Camp

In conforniity with the design of the oficials of the United States Steel Corporation for the standardization of the methods employed in the sampling and analysis of all materials encountered in their various lines of manufacture, the Chemists' Committee presents this compilatioti of standard methods for the sampling and subsequent analysis of molten pig-iron. In selecting the methods, the Committee employed the same line of procedure as in former cases, viz., the careful consideration of all the methods employed in each laboratory of the Corporation, evolving therefrom the several methods herein described, the immediate adoption of which is desired. The services of Messrs. W. B. N. Hawk, William Brady, and C. H. Rich, a sub-committee appointed for the preparation of the present paper, are gratefully acknowledged. II. Introduction. A quite obvious cause of nonconformity of results of comparative analyses in the various laboratories of the Corporation has been an apparent lack of uniformity of method in the sampling and analysis of molten iron. This condition is particularly apparent with regard to the determination of the sulphur, numerous discrepancies in which would appear t.o indicate the absence of, and the necessity for, some uniform method of procedure. The estimation of the

Jan 1, 1913