Search Documents

By G. R. St. Pierre, L. M. Adelsberg, R. Speiser

The rate of scale fot'~I~ti0n on tantalum held in H20-Hz-Ar gns mixtures at temperatures between 840" and 1250°C is related to gas composition and ternpevature. It is found that water vapor partial pressure determines the oxidation rate at a given temperature and that the oxygen potential as fixed by the water vapor to hydrogen ratio Ins no significant effect on the oxidation rate. The Ta205 scale formed during oxidation is composed of an inner lattice-dijf~ision barrier and an outer layer of- cracked/porous oxide 1 HE oxidation of tantalum at temperatures less than 800°C is characterized by solution of oxygen into the metal,'-' the formation and growth of suboxides into the metal,')2~10-15 and the delayed nucleation of the highest oxide, Above 800°C, Ta205 is found to nucleate rapidly10, 11, 15, 16 except at low oxygen pressures:15 however, there is uncertainty regarding which does not retard the oxidation process. For each gas con~position and temperature investigated, the oxidatioz rate becomes constant after a short adjustment period. It is shozm that a constant oxidation rate nzay pre~?ail even though the tlzickness of the inner lattice-dijjitsion layer of Ta205 is clanging. TFze initial czcrz!ature of the typical 'Paralinear" oxidation curve may result froprz causes other than an increasing thickness of tlze inner protective layer. the detailed mechanisms of the high-temperature oxidation. Peterson, Fassell, and wadsworth17 observed linear oxidation behavior for tantalum in oxygen at temperatures between 600" and 1000°C. They reported that equilibrium adsorption of 0, occurs on a surface prior to the rate-deter mining step of the reaction. Cowgill and stringer1' confirmed the observations of Peterson and his coworkers. They stated that the rate-determining step of the reaction could be either the incorporation of adsorbed oxygen into the anion lattice or the dissociation of 0, at the gas-oxide interface. The relative rates of the two surface reactions were proposed to be dependent upon the reaction temperature and the oxygen pressure. stringerlo subsequently reported that the reaction surface is located somewhere

Jan 1, 1968

By P. P. Reichert, L. S. Gournay, N. T. Burdine

An investigation of equivalent pore entry radii in typical samples of petroleum reservoir rock and the pore volume associated with each value of pore entry radius has been made. Theoretical discussions together with experimental procedures for obtaining pore entry radii and the distribution of pore volume with pore entry radii are presented. Experimental results on a number of core samples, along with typical distribution curves, are shown. Data on the per cent of the pore volume filled by mercury at a pressure of 1500 psi are included. The results of re-runs of samples, made possible by regenerative apparatus, show the repeatability of the data and indicate the amount of physical change in the samples by mercury penetration. Theoretical equations for calculating permeability from pore size distribution data were derived and the results of such calculations are compared with measured gas permeability data. The effect of the shape, surface area, and weight of the sample on the pore size distribution of reservoir rocks was investigated experimentally. Mercury capillary pressure curves are compared with those obtained by the porous diaphragm method using pas to displace water. Standard core analysis techniques, in general, lead to quantities which are statistical averages of the varying properties of the samples under examination. Although such statistical information has real value in predicting the gross performance of porous bodies. it fails to provide fundamental information concerning the properties of the porous medium itself or any processes which may be occurring in it. For example, a gas permeability measurement on a core sample is an indirect way of determining an average pore radius for that particular sample. Since there are many combinations of pore radii that will give the same radius. and, hence, the same permeability, no information is obtained on the pore size distribution. Furthermore, similar values in permeability do not imply similarity in other properties of a porous medium. For instance, it is possible to have two core samples with identical permeability which would have different residual oil contents at the end of an air-oil drive, or even different amounts of interstitial water. It has been recognized for some time by the petroleum industry that a determination of pore size distribution for porous reservoir rocks offered promise of increased understanding of fundamental flow processes in the porous matrix. and therefore of petroleum res- ervoir performance in general. There have recently been published several methods for determination of pore size distribution in porous materials. A report is given here of the modifications in equipment and technique required to adapt one of these methods to measurements on petroleum reservoir core samples. Although only a few correlations or applications of the method are available for presentation at this time, the technique is brought to the attention of the industry so that the opinions and experience of others with this or similar techniques may be exchanged. It seems possible that the method will have wide application in the future. METHOD There are three general methods which may be employed to measure the pore size distribution in naturally occurring rock formations. One method1 is based on experimentally determined adsorption isotherms for calculating the surface area of the porous medium. Knowing the surface area and the pore volume, a rough estimate of the pore radius can be made. Since this method depends on the thickness and uniformity of the adsorbed layer, the validity of the results would be highly questionable. A second method utilizes capillary pressure data obtained by static dis-

Jan 1, 1950

By J. H. Faulk

An examination is made of the various factors influencing drilling rate and drill bit life in various diameter holes. It is concluded that drill bits in the size range 4% to 6 1/4 in. can be used to attain substantially the some daily drilling progress as conventional size bits in soft rock drilling operations. An examination of the most important factors influencing "hazard of losing the hole" in the different hole size results in the conclusion that the smaller hole sizes can probably be drilled at reasonably low risk. However, this risk will be somewhat greater in the smaller diameter holes, requiring that special drilling and mud engineering practices be used to make small diameter holes practicable in soft rock drilling operations. An engineering analysia is made of the power and hydraulic requirements of several drill string-hole combinations to test the feasibility of drilling .small diameter holes in soft rock areas. Large econormies in rig power requirements appear possible by drilling .smaller .size holes in these operations. INTRODUCTION The industry now is re-examining the utility of small diameter holes in the light of substantial technical advances made in recent years. Faced with increasing cost of finding reserves and with proration after developing them, the industry must either develop methods of economizing or receive a lower rate of return on investments. Small diameter holes appear to involve an attractive method of economizing. Our objective is to determine if this is technically possible in soft rock operations. Soft rock, as used in this report, refers to those formations of a "drill-ability" corresponding to that of all Gulf Coast formations shallower than and frequently including much of the Eocene rock system. An important phase of technology which we shall examine is relative drilling rate and bit footage which may be obtained with various size bits. Rig operating efficiency, particularly as influenced by hazard, is also discussed in detail. The technical conclusions resulting from these examinations are used to develop sample drill string design and rig horsepower requirements for drilling holes as smaH as 4 3/4 in. and larger. The principal criterion used for the drill string design is that approximately the same daily drilling progress would be possible in all size holes in soft rock operations. This facilitates a comparison of rig size required for drilling the hole sizes in the range between 4 3/4 and 8 3/4 in. BROAD PROBLEM OF DRILLING RATE AND BIT FOOTAGE The three factors controlling daily drilling progress are: (1) drilling rate of bit while on bottom turning, (2) bit footage, and (3) rig operating efficiency. Let us look now at the first two of these factors. Drilling technology has progressed to the point that a semi-quantitative analysis of the effect of various operating variables upon these factors can be made. Those factors which apparently limit both drilling rate and bit footage for bits now in use are: (1) bit design, (2) weight on bit, (3) hydraulic cleaning capacity for bit cutting surfaces and hole bottom, and (4) rotary speed. (We neglect the effect of mud and formation properties because these factors arc the same for the various size bits.

Jan 1, 1957

By C. E. Sims, G. A. Moore, D. W. Williams

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By R. J. Sandrea, S. M. Farouq Ali

The results of an experimental and theoretical study of the effects of rectilinear impermeable barriers and highly permeable channels on the sweep efficiency and conductivity of a five-spot network are presented. The study was carried out using Hele-Shaw, and conductive sheet analogs for both. normal and inverted flood patterns. A functional relationship was developed which provides quantitative prediction of the above parameters; i.e., sweep efficiency and conductivity, for the nonhomogeneous system. To evaluate this, it is necessary only to measure the interference modulus of the obstacle using a simple expression. The results indicate that impermeable barriers, with an interference modulus greater than zero, always cause a decrease in the conductivity and the sweep efficiency of the pattern. On the other hand, permeability channels do not have a significant effect on these parameters, unless they are located along the streamlines. The study also discusses a method of formulating the difference equations pertaining to the two-dimensional Laplacian in a system containing rectilinear barriers. In addition, a technique is described for tracing the progress of a free surface, using marked particles, in a stream containing discontinuities SuCh as those occurring at the extremities of barriers. The above computational scheme was used in a digital computer program to simulate results of the Hele-Shaw analog. The computed values of sweep efficiency mere in good agreement with the experimental values. INTRODUCTION At the present time waterflooding remains the most widely used technique for the secondary recovery of oil. Among the numerous factors that affect the performance of a waterflood, the areal sweep efficiency constitutes one of the most critical parameters. It is a function only of the geometric distribution of the wells for a homogeneous medium and unit mobility ratio. Geological considerations, however, such as the presence of sealing faults or solution channels in the rock matrix, would generally exert an adverse effect on the areal sweep efficiency of a waterflood network. Surprisingly little information is presently available on the quantitative implications of such permeability interferences. It was the object of this investigation to consider the presence of rectilinear, impermeable and highly permeable interferences in an otherwise homogeneous five-spot pattern, and to analyze their effects on the resulting sweep efficiency and pattern conductivity. The experimental phase of the study was conducted using two different models: the Hele-Shaw flow cell and the field plotter. For experimental convenience, the geometric boundaries of the five-spot were assumed to constitute streamlines even in the case where the interference was asymmetrically placed with respect to a repeated five-spot pattern. A second object of the study was to develop a computational scheme for numerically calculating the pressure distribution in a five-spot flow pattern containing rectilinear, impermeable barriers, and to use this distribution to compute the sweep efficiency. EXPERIMENTAL PROCEDURE HELE-SHAW ANALOG The Hele-Shaw analog was used both as a visual model and for determining the sweep efficiency for systems involving impermeable barriers. The physical limitations of this model as a means of experimentally studying the motion of a fluid in porous medium have been adequately discussed elsewhere.2,7 Likewise, it can be easily verified that the analogy remains valid when a portion of the region between the plates contains an obstacle of the same thickness as the distance between the plates. The model used in this study was composed of

By C. Kremer Bain

UNDER present economic conditions the necessity of mechanizing the mines of our country has become a very important problem. More and more mines are looking toward increased or complete mechanization of their operations, so in the writer's opinion it is quite pertinent that some of the associated problems that accompany such a program be pointed out. The following generalization on attempting a comparatively slight change in mining methods at the Southeast Missouri properties of the St. Joseph Lead Co. is an attempt to point out to anyone faced with a mechanization program that much time and C. KREMER BAIN, Member AIME, is Assistant to General Manager, St. Joseph Lead Co., Bonne Terre, Mo. AIME Sun Francisco Meeting, February 1949. TP 2743 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Dec. 27, 1948; revision received Oct. 13, 1949. effort can be saved, and many headaches avoided, if company policy can be established whereby everyone in the organization from the top down is desirous of improvement and is working towards the common objective. Any changes in mining methods, machinery, and so on, must entah coordination of all the other phases of mining as they all have to mesh as accurately as a smooth running chain of gears if satisfactory results are to be obtained. The purpose of this paper is to point out some of the problems which :have to be surmounted when any mechanization program is attempted, rather than to go into the mechanical details and actual operating data of the equipment employed. After all, machines have to be adapted to best suit the local conditions, so no general formula can be given that would apply to other properties. Although St. Josepll Lead Co. has been mechani-cally-minded for a number of years, as shown by the fact that over 110 million tons have been loaded mechanically since 1922, any further mechanization or changes always present a problem. When our ore bodies were of great height and area the breaking and loading were developed to a high degree of efficiency according to known standards. But in recent years, when our ore bodies became smaller and more scattered, the amount of tonnage we were able to break was not sufficient to supply our shovels with enough rock to keep them working to capacity. Our first step in attempting to rectify this situation was to develop a technique of moving the shovels to the broken ore in various stopes, which sometimes entailed a move each shift. A shovel is not producing when being moved, so within the last two years we have been endeavoring to devise some means of getting more rock broken in these smaller stopes and it was then that we became interested in jumbo drilling. To illustrate the fact that mechanization is a process of a chain of developments rather than a stroke of genius can best be shown by a general summary of conditions and obstacles which were encountered in our present attempt to establish template drilling of a standardized round. Our first jumbo was more or less the conventional type with two machines mounted on a crossbar. This arrangement proved to be impractical to duplicate satisfactorily the regular routine of slabbing in a more or less radial pattern as carried out by column drilling. One machine was either too close to or too far from the face and there was another disadvantage in that one drillman was frequently delayed while waiting for his partner to bottom a hole. Our next step was to eliminate the crossbar so the machines could operate independently of each other, but we still encountered the same objections mentioned above except that one drillman was free to drill three holes instead of one in a vertical plane independently of his partner. Time studies while trying to adapt the jumbo to the regular slabbing practice as accomplished by column drilling, revealed that twice as much time was spent in maneuvering the jumbo into position and aligning the holes as was consumed in drilling.

Jan 1, 1951

By Reinhardt Thiessen

Under sulfur in coal, is usually understood that form of sulfur which is combined with iron and known as pyrite. It occurs in the form of balls, lenses, nodules, continuous layers, thin sheets, or flakes, both in horizontal planes and vertical cleavage fissures. But pyrites also occur as very fine microscopic particles, or nodules, disseminated through the compact coal. This form has had but very little consideration. Finally, there is sulfur in coal in an amicroscopic form (not visible with an ordinary microscope), probably combined with the organic matter that exists in the coal. This form has had considerable attention from a scientific standpoint, but has probably not been recognized enough on the economic side. One or the other, or both, of these two latter forms may comprise the larger part of the sulfur content of coal, especially after it has been washed or otllerwise prepared for use. Pyrites in Microscopic Particles All coals that have been examined by the author contained a varying amount of sulfur in very small globules, or particles, of pyrite. These particles are seen in a thin [section as roughly rounded opaque dots, Figs. 1 to 10. When isolated, they are generally shown to be approximately spherical in shape, with a rough outer surface. They vary in diameter from a few microns to a hundred microns, the majority messuring from 25 to 40 microns; relatively few exceed the latter diameter. They are, therefore, very small objects. Their size is best appreciated by comparing the illustrations, in which they are shown. at a magnifiea tion of 100 diameters, with some known area like the period used in the ordinary printed page. The period is about 0.6 mm. in diameter, and . when magnified 100 times, will cover a circular area of about 2 1/2 in. in diameter, or all but the corners of the illustrations. The illustrations, therefore, represent an area about as large as an ordinary period, and the pyrite globules form but a small part of the total area. Very frequently a number of these particles are joined together in horizontal rows; oc-

Jan 1, 1920

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. Introduction The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or Pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves is needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry Out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemica1 composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. The Problem At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1942

By G. H. Kesler, C. E. Dryden, J. H. Oxley

Rates of heat- and mass-transfer from rods to recirculating air were determined within a one-quarter-scale model of a metals deposition bulb. The dependence of local and averaged rates of transfer upon outlet geometry, number of rods, position upon a rod, and airflow rate was established for flow patterns created by radial and tangential air inlets. The results are given a qualitative interpretation in terms of rates and distribution of metal deposition in a prototype deposition bulb. IT is well known that a number of metals can be prepared from volatile compounds containing them by causing dissociation of their compounds to occur at heated surfaces. Examples of such metals include silicon, titanium, zirconium, and aluminum, which can be prepared from their halides. While the ability to prepare high-purity metals by this technique is of importance in itself, the rate of deposition of metal also is important in considering the commercial potential of such a process. If the over-all process of deposition is broken down into separate steps of transport of materials to and from the heated deposition surface and establishment of chemical equilibrium at the surface, as was described in a recent paper,1 then since surface temperatures are usually high and surface equilibrium is attained very rapidly, the rate-controlling step can be considered as either that of transport of reactants to the surface or of transport of products other than deposited metal away from the surface. These two transport steps are related through the reaction stoichiometry. It can be shown1 that the rate and distribution of metal in such a transport-controlled process are determined by the over-all and local mass-transfer coefficients in conjunction with the equilibrium conversions at the hot surfaces. The rate relationship is: w = [KA(y a-y s)] B.E where the bracketed group is the rate of arrival of the reactant at the surface of area A as determined by the mole fraction driving force (y a - y s) and the convective transport constant K. The factor B is the weight fraction of metal in the reactant, and E is the equilibrium fractional conversion to metal. Numerical values of y, and y, are fixed by the vapor composition and the equilibrium compositim of reactant at the surface; and E can be determined by thermodynamic calculations or by experiment. However, values for the convective coefficient K are available generally only for systems of simple geometry, such as cross-flow past a rod or sphere or parallel flow past a flat plate or through a tube. Often it is necessary to work with systems of more complex geometry and in which the vapor flow may not be uniform or exactly parallel or perpendicular to the surface. It is possible, of course, to establish working correlations for these more complex systems by direct experiment; but the experiments usually are costly in both time and money. To circumvent this objection and to aid in arriving at an understanding of the relationships and interactions of the process variables, it is helpful to construct a model of the flow system in which air, water, or other convenient fluids can be substituted for the process vapors and with which mass-transfer measurements or analogous he at-transfer measurements can be made upon a simulated deposition surface. By this means, a large number of measurements can be made in a reasonable time, and the correlation of these results can be applied to the prototype system. Examples of the application of these techniques are to be found in the literature (e.g., Ref. 2). It is the purpose of this paper to illustrate these techniques by description of a model study which was done at Battelle Memorial Institute. The work to be described was of a preliminary nature; the investigation subsequently was extended to develop quantitative relationships among the significant dimensionless transport, geometric, and flow parameters. This more detailed study will be the subject of a future paper.

Jan 1, 1962

By D. G. Russell

A simple method has been developed with which flowing bottom-hole pressure data from two-rate flow tests in oil or gas wells can be analyzed to estimate the formation permeability, skin factor and average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized producing rate of the well is changed to another, higher or lower, rate. The new method yields the same information as a conventional pressure buildup analysis, but eliminates the need for closing in the well. The analysis of a two-rate flow test is of the same degree of difficulty and requires about the same engineering time for application as a conventional pressure buildup analysrs. The extended closed-in periods experienced with conventional buildups because of long, low-rate afterproduc-tion periods are eliminated by fIow tests. Other anomalous pressure buildup effects, such as "humping" due to weli-bore phase segregation, can be successfully eliminated with the new method. Generally, flow tests of about 24 hours' duration run with conventional pressure measurement equipment are sufficient for interpretation purposes. Field testing of the two-rate flow test method has established that it is a reliable and economical method which can be used in many instances to complement or even replace conventional pressure buildup methods. INTRODUCTION The principal method for estimating formation permeability and well damage, or skin factor, in a producing oil or gas well is the analysis of shut-in bottom-hole pressure buildup data.' This familiar method has been used quite successfully by reservoir engineers for many years. It is based on the solution of the radial flow equation for constant rate conditions, and requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed t + ?t bottomhole pressure vs log t + ?/?t(where At is shut-in A? time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the permeability, skin factor, and reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. Over the years several drawbacks have become apparent in the use of conventional shut-in pressure buildups for determining permeability and skin factor. The conventional pressure buildup interpretation theory assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing in to the formation. This adjustment period is commonly referred to as the "after-production" portion of the pressure buildup. In the tight reservoirs, long, low-rate after-production periods frequently occur, and the well must be shut in for several days or, in some instances, even weeks to obtain an interpretable buildup curve.' Obviously, such long shut-in times can cause loss in current income, both from reduced oil production and from the fact that personnel and pressure measurement equipment are occupied with a single well for too long a time. In other cases, even long shut-in periods do not seem to be of much aid in obtaining an interpretable buildup." If there is considerable phase redistribution (liquid fallout or bubble rise) after a well is shut in, then curves with no interpretable portion are often obtained during the buildup. In addition to instances in which wellbore effects cause trouble, there are also cases in which the major objection to use of the closed-in pressure buildup is simply the fact that the well must be shut in. When there is no proration and when the well has limited producing capacity. closing in the well means loss of income. From the foregoing discussion it is apparent that it ib desirable to have an alternative method of obtaining the same information as that derived from a conventional buildup without the need of closing in the well. One possible solution which has been offered for this problem is the use of a bottom-hole shut-in tool' which isolates the major portion of the flow string from the formation face during the buildup. In this paper an alternative method which is frequently successful in avoiding wellbore effects and which does not require the use of special equipment is presented. A new, simple method has been developed with which the flowing bottom-hole pressure data from flow tests in oil or gas wells can be used to estimate permeability, skin factor and the average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized production rate of the well is changed to another, higher or lower rate. The need for closing in the well is eliminated, and pressure measurement periods of only 18 to 24 hours arc usually sufficient, even in tight reservoirs. Thus, the new

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. Introduction The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or Pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves is needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry Out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemica1 composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. The Problem At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1942

Jan 1, 1924

By Otto C. Kopp, Thomas B. Crattie, Dennis R. Owen

Whole-rock analyses of limestones, fine-gralned dolostones and coarser-grained dolostones adjacent to mineralized breccias (Coy mine, Mascot-Jefferson City district) were compared with similar lithologies adjacent to apparently non-mineralized breccias at the new Thorn Hill section located approximately 39 km north of the Coy mine. Specimens were analyzed for Ca, Mg, Si, Al, K, Fe, Mn, Sr, Br, C1, S, Ti and P using X-ray fluorescence analysis. The concentrations of the major and most minor elements for Thorn Hill specimens fall within the range of concentrations for Coy mine specimens; however, significant differences (probability < 0.05) were noted for Fe, C1 and Br for fine-grained dolostones and for MgO, Fe and Mn for the coarser-grained dolostones. No significant differences were detected for the limestones.

Jan 1, 1985

Recent start-up of a new 3450 t/d (3800 stpd) copper-zinc concentrator complex in northern Manitoba, Canada, is expected to open new reserves and dramatically cut transportation costs for Hudson Bay Mining and Smelting Co.&apos;s Snow Lake operations. The new $C33-million mill is located in Stall Lake, Manitoba, and includes a new crushing and grinding facility and two flotation circuits for the production of 23-25% copper and 55% zinc concentrates. A small amount of lead concentrate will also be recovered. The plant will produce some 145 000 t/y (160,000 stpy) of concentrates, to be shipped by rail to the firm&apos;s Flin Flon copper smelter and zinc refinery complex, located 177 km (110 miles) to the west on the Saskatchewan-Manitoba border.

Jan 9, 1979

By Orville Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually increases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal.

Jan 5, 1951

By Z. M. Zavodni

The stability of waste dumps depends to a great extent on the physical properties of the underlying foundation. These physical properties are evaluated through surface geotechnical surveys, subsurface exploration, and field and laboratory testing. Sufficient information must be obtained to define and assess the strength, consolidation, distribution, topographic and hydrogeologic properties for these materials. Important foundation data collected in the field include: surface infiltration rates, downhole hydraulic conductivities, ground water levels, bedrock structural parameters, soil types and soil thickness. Laboratory testing should identify the classification, strength, moisture content, hydraulic conductivity, attenuation and consolidation characteristics. Summarized in this paper are procedures and typical results of porphyry copper leach dump foundation investigations. Laboratory properties and design recommendations for potenia1 foundation liner materials are described. Back analysis and laboratory foundation strengths are compared. The topographic effect of the foundation on dump behavior is discussed and a foundation pore pressure monitoring experiment at the toe of an active waste dump is described.

Jan 1, 1985

By Carlos D. da Gama, Charles R. Nelson

Griffith’s theory of brittle fracture, as modified by McClintock and Walsh to fit rock behavior in cases of failure by compression, has been successfully applied in various fields of rock mechanics. Extension of the Griffith&apos;s criterion to rock blasting problems may also be more representative of rock behavior than the simple consideration of a criterion of failure based on the dynamic tensile strength of the material. If consideration is given to pre-existing cracks within rock structure, occurring not only because of the discontinuous properties of rocks, but also as a result of drilling operations that normally precede blasting, those cracks can be propagated under the action of the dynamic stresses (radial and tangential) induced by the passage of the wave emitted by the explosion. Conditions for initiation and propagation of pre-existing cracks are deduced in terms of rock properties and explosives performance. Influence of the different variables governing the phenomenon is discussed after considering an actual example. Results seem to be well correlated with experimental evidence of radial cracking observed in blasting with high explosives acting within hard rock.

Jan 1, 1971

By A. C. Noble, D. E. Ranta

Orebodies with intricate three- dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer- assisted methods. &apos;The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist&apos;s interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral de- posits.

Jan 1, 1984

By J. L. Rodda

A large amount of time has been devoted to the microscopical study of the copper-zinc alloys, emphasis naturally being placed upon the commercially important alloys of the system. Suitable methods are available for microscopically recognizing the two phases richest in copper, but none appear to have been developed for the positive identification of the other phases. This is, however, accomplished, for the phases normally encountered, by an electrolytic method described in the following pages. Five phases of the copper-zinc diagram (Fig. I) are considered for the purpose of this paper: the solid solution of zinc in copper, alpha (a); the intermediate phases, beta (ß), gamma (?), and epsilon (e); and the solid solution of copper in zinc, eta (11). Beta prime is not considered a separate

Jan 1, 1937

By W. M. Aubrey, P. L. Steffensen

AUTOMATIC grinding control for ball mills in closed circuit with cyclones was developed for the concentrator of the Marmoraton Mining Co., a subsidiary company of Bethlehem Steel Corp. The concentrator, located at Marmora, Ont., Canada, treats an ore that analyzes 35 to 40 pct magnetic iron. Magnetite, the recoverable iron mineral, is concentrated by fine grinding and magnetic separation. The mesh of grind obtained in the plant is not determined by the point at which liberation is sufficient to yield a satisfactory grade of concentrate, but by the physical requirements of the downstream pelletizing operation. This is considerably finer than is metallurgically necessary. The concentrator has two identical units, each consisting of a rod mill in open circuit, followed by a ball mill in closed circuit with a cyclone and two rougher magnetic separators. The cyclone was chosen as a classifier because of its high efficiency on heavy gravity, magnetically flocculated material.

Jan 1, 1957