Search Documents

By John T. Norton, V.G. Mooradian

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By Junius D. Edwards

WHEN Charles Martin Hall invented the electrolytic process for the production of aluminum, one basic requirement was a supply of pure alumina. Now, more than 50 years later, the same requirement still holds, and there are no technical straws in the wind to indicate that this situation is likely to change. Long ago, Aluminum Company of America took a number of steps to see that this country should not face shortages of alumina and aluminum in time of emergency. As one step to this end, the Company developed and used a supply of bauxite in South America in order to conserve dwindling Arkansas reserves. Another, and more a program than a step, was to investigate every type of process that might bear the possibility of utilizing the low-grade ores of aluminum that are more plentiful than bauxite. It is a long story, but the investigation included electric-furnace processes, acid extraction processes and alkaline extraction processes, with or without preliminary furnace and sinter treatments. Some of the processes developed were operated in commercial production. This work has been continuous since the first World War. The turn of the wheel came sooner than was expected when, in 1942, bauxite shipments through the Caribbean became uncertain and hazardous through the operation of submarines. The tremendous requirements of aluminum for the war effort were consuming high-grade bauxite at an alarming rate and a national search for substitutes began. High-grade bauxites, for technical and economic reasons, have been defined as those containing about 7 per cent or less of silica. While bauxite of this grade was limited in amount in the United States, there was in sight a substantially greater volume of low-grade, high-silica bauxite not amenable to economic treatment by the Bayer process, but richer in alumina than the clays or other available low-grade ores. It was at this point, and after several years of intensive research on this particular phase of the problem, that Aluminum Research Laboratories brought to completion the invention of one of its research staff, which made practical the utilization of large reserves of low-grade bauxite in America. BAYER PROCESS The Bayer process has been almost universally used for the 'production of alumina from bauxite. This process, in outline, comprises the digestion of finely ground bauxite in a solution of caustic soda (NaOH) under pressure and at an elevated temperature. Alumina in the bauxite goes into solution as sodium aluminate and the impurities-oxides of iron, titanium and silicon-remain undissolved. The undissolved residue, known as "red mud," from its color, is separated and run to waste. Aluminum hydrate (A1202.3H20) is precipitated from the solution of sodium aluminate, and the liquor containing the caustic soda and some alumina is returned to the process for digesting more bauxite. The aluminum hydrate, after washing, is calcined at a high temperature to produce

Jan 1, 1945

By R. W. Kraft, F. D. George, F. D. Lemkey

From a conszderation of the geometrically possible ways in which an array of lines or linear features in three-dimensional space can depart from a statistically random arrangement, a system was developed to describe and measure different types of anisotrypic arrangements of lines in opaque solids. The technique was applied to a specimen of unidirectionally solidified Al-Cwll, eutectic which contained microstructural imperfections termed lamellar faults. Experimental data obtained from photomicrographs of different facets of a grain of this alloy were then analyzed using this system. It was deduced that the defects, which are essentially linear in natuve, were predominantly parallel to one another but not parallel to the nominal growth direction probably because of some lateral heat flow during solidification. InGOTS of lamellar eutectic alloys which have been unidirectionally solidified under growth conditions which prevent colony formation consist of large elongated grains in which the lamellae are approximately parallel to one another. Deviations from a parallel lamellar structure within a grain are caused by extra lamellae which form occasionally during the solidification process. Three-dimensional analyses of such specimens have revealed that one extra platelet produces two defects, termed 1amellar faults, which can and do grow more or less independently of one another.' The faults are analogous in many ways to edge dislocations in crystals. If a lamella of one phase is considered to be basically two-dimensional, e.g., a surface, then a fault can be defined as the locus of points which delineates an edge (or half the periphery) of one extra lamella as it grows and forms bridges and saddles in an otherwise parallel arrangement oi lamellae, Fig. 1. Were it not for the fact that bridges and saddles occur in the structure, the extra platelet could be defined as the unit defect and the concept of linear faults of positive and negative character around the periphery of the extra platelet would be unnecessary. If an extra platelet is merely inserted (actually it is grown in) between other parallel platelets, the fault line around the periphery of the extra platelet would circumscribe one and only one platelet, namely the extra one, and the faults would lie in a plane parallel to the lamellae. But when an extra platelet merges with adjacent ones and each side grows independently of the other, it is no longer topologically possible to delineate "the extra plate." A fault circuit which either closes on itself or passes out of the specimen still occurs although it no longer will be coplanar with the lamellae. In fact, it is usually not even Planar even if the lamellae are. Under these conditions a concept that a specimen contains N extra platelets of a given size per unit volume would be very artificial and consequently meaningless. Therefore, because of the topological complexity of the alloys, it was deemed necessary to define one-dimensional

Jan 1, 1962

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964

By V. G. Mooradian, John T. Norton

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By Edward Adarns Richardson

As developed up to the end of the Great War, an airplane was essentially a mechanism of wood and fabric, joined and held together by metal fittings and fastening. The engine and accessories, wire for wheel spokes and other tension members, and the occasional use of metal for inter-plane struts and the shafts of surface controls required some metal, but essentially it was a wood and fabric structure. Attempts had been made to use metal for other purposes, such as struts in the drag-trussing of wing panels and for short interplane struts, and Junkers had produced an airplane of iron in 1915. By 1917 he was using steel tubes and duralumin sheets, securing noteworthy advantages aerodynamically and from the standpoint of weight and upkeep. He was a pioneer along lines in which progress is still being made. Principles of Airplane Construction The loaded weight of airplanes ranges from 500 lb. for the light plane of which we heard so much a short time ago, to about 40,000 Ib. The great majority of planes range from 2000 to 10,000 Ib. Of this weight from 15 to 30 per cent. is for the dividend-earning load. This percentage is so low that every per cent. saved on the rest of the weight increases the pay load from 3 to 6 per cent,. The economic value of every pound that can be saved in designing or constructing a plane is sufficiently great to warrant spending money on refined methods of structural analysis, materials of superior strength properties for a given weight, methods of manufacture which may make possible the use of refinements in structural design, and the like, to an extent unknown heretofore. The weight of the airplane, without fuel, oil and crew, and pay load, ranges from 50 to 65 per cent. of the total weight loaded for planes suitable for commercial use. It is doubtful if the structural weight will ever be brought down to as low as 40 per cent. for commercial planes. The airplane may be roughly divided into: (1) Power plant, which includes engines, radiators, cooling water, oil and fuel tanks, piping, propellers, engine-starting systems, pumps, super-

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 468.3°C (875°F). The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of their durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica (SiO2) and silicates can be melted to form glasses. Alumina (A1203), present in a mineral compound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus sand, which is generally almost pure SiO2, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide performs a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some nonminerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1983

By R. Schuhmann, G. W. Powell

The concept of local equilibrium is examined and, in particular, the applicability of the concept to two-phase binary diffusion couples is discussed. It is concluded that, if binary solid solutions are treated thermodynamically as ternary solutions, vacancies being the third component, then recent experimental observations of nonequilibrium interface compositions (i.e., compositions different from the phase diagram values) are consistent with a state of complete dynamic equilibrium at the interface. CLASSICAL approaches to diffusion and to other irreversible processes often utilize a postulate of "local equilibrium". That is, one assumes even in the presence of gradients, fluxes, and time changes of properties, a) that the Second Law can be formulated locally, and b) that thermodynamic equations of state among intensive properties are identical with those for equilibrium phases. A direct consequence of this assumption, for example, is that one would calculate the total entropy of a nonequilibrium phase simply by integrating the entropy density (eu per unit volume) over the volume of the phase, assuming that entropy density is the same function of energy and particle density as for equilibrium phases. In the study of diffusion and of diffusion-controlled phase transformations, metallurgists take this concept of local equilibrium for granted and utilize it automatically. In fact, experimental evidence of all kinds is overwhelming that "local equilibrium" is a valid limiting law, approached more and more closely as gradients and rates of change approach zero. On the other hand, we have neither experimental nor statistical thermodynamic proof that this principle of "local equilibrium" should remain rigorously valid at high gradients and for rapid processes. Theoretically, in fact, one would expect deviations because interactions between adjacent volume increments of material affect the evaluation of entropy. Also one observes experimentally structural and small energetic differences between equilibrium and nonequilibrium phases. The purpose of this paper is to present a thermodynamic framework for the study and correlation of deviations from strict local equilibrium in isothermal diffusion and related processes. This procedure, in effect, preserves the principle of local equilibrium by thermodynamically assigning the deviations from static equilibrium properties to a defect component. Although this theory is entirely phenomenological, the possibility does exist of correlating the theory with experimental observations of defects under favorable circumstances. The most immediate application appears to be to the equilibria at the interfaces in two-phase binary diffusion couples. A recent pertinent work by Eifert et al.1 has shown that the concentrations of aluminum in the a(fcc) and B(bcc) phases at the 0-8 interface in Cu:Cu-12.5 wt pct A1 diffusion couples are greater than those given by the phase diagram. It is postulated by these authors that the supersaturation of the o phase at the interface provides the driving force for the a-to-B lattice transformation; the excess free energy of the a phase, ?Gaxs, arising from the greater-than-equilibrium aluminum concentration is about 3 cal per g-atom. On the basis of the schematic free energy-composition diagram shown in Fig. 1, Eifert et al. concluded that the thermodynamic situation at the interface is one of the partial equilibrium; that is, = for the more mobile aluminum whereas will be reexamined in the latter part of this paper. THERMODYNAMIC PROPERTIES OF DEFECTS A rigorous analysis of the thermodynamics of defects requires an added degree of freedom in the Phase Rule sense, because the standard formulations of solution thermodynamics (partial molal properties of components, free energy minimization, equality of chemical potentials, and so forth) involve the implicit

Jan 1, 1970

By J. H. Swisher

In measuvements of the solubility of nitrogen in fer-rilic Fe-P alloys, tile nitrogen solubility is found to be Less in pIrospliorus-bearing alloys than in pure iron. The reduction in solubility is about 20 pct in a 1.0 wt pct P alloy at 1300°C and about 30 pct in a 0.23 wt pct P alloy at 440°C. Diffusion coefficient measurements at 1150 and 585°C show that phosphorus also decreases the nitrogen diffusivity in iron. In previous work on the Fe-P-N system, phosphorus was found to reduce the nitrogen solubility in liquid iron slightly.&apos; Indirect evidence for similar behavior in a Fe at low temperature was obtained by Dickenscheid and Brauner.&apos; These authors found that phosphorus reduces the height of the internal-friction peak due to dissolved nitrogen. The results of Dickenscheid and Brauner were confirmed by J. C. Swartz of this Laboratory in a single internal-friction experiment using the same specimen stock as in the solubility measurements described below. In the present investigation, the solubility of nitrogen in a fer rite-stabilized Fe-1.0 wt pct P alloy was measured in the temperature range from 800" to 1300°C. Additional experiments were performed in the temperature range from 440° to 585°C, using an Fe-0.23 wt pct P alloy and NH3-H2 gas mixtures. EXPERIMENTAL The experiments were performed in a vertical tube furnace wound with platinum wire. For experimental temperatures of 800°C and above, a mixture of 5 pct Hz in N2 was used as the reacting gas. The gas mixture was prepurified from oxygen by passage over platinized asbestos at 450°C, and subsequently over anhydrone to remove water. Flow rates of the gases were measured with capillary flow meters. The temperature was measured before and after each experiment with a Pt/Pt-10 pct Rh thermocouple. The specimens used for the high-temperature solubility measurements were in the form of rectangular plates, 0.534 by 1.6 by 3.8 cm. The specimens were cleaned in trichloroethylene and annealed for 2 hr in hydrogen at the beginning of each experiment. In measuring the nitrogen solubility, the specimens were held in the reacting gas until equilibrated, then cooled in a water-cooled copper block at the bottom of the furnace. The time needed for equilibration at 1150°C was determined by measuring the average nitrogen content of the 1.0 pct P alloy as a function of reaction time. As will be described, the nitrogen diffusivity in the alloy at 1150°C is only slightly less than its calculated diffusivity in pure iron. At temperatures other than 1150°C, the reaction time used in measuring the nitrogen solubility was about twice the calculated equilibration time for pure iron at the same temperature. With a few exceptions, the procedure for the low-temperature solubility measurements was the same as that described above. The compositions of the NH3-H2 gas mixtures were determined by collecting gas samples from the gas train and analyzing them for NH3 by titration with HC1. The specimen thicknesses were less than those used for the high-temperature experiments, eg., 0.124 and 0.051 cm for measurements at 585° and 440°C, respectively. Nitrogen concentrations were obtained by chemical analysis, using the Kjeldahl method. The Fe-P alloys were made by adding ferrophos-phorus to electrolytic Plastiron (Type 104 A). Commercial ferrophosphorus, containing 3 pct Mn and 0.35 pct Si as the major impurities, was first purified by melting under an FeO slag. In a separate heat, the electrolytic iron was melted and vacuum-carbon-deoxidized prior to making the ferrophosphorus addition. The principal impurities and their concentrations in weight percent in the 1.0 pct P alloy are as follows: Mn, 0.01; Si, <0.01; C, 0.01; 0, 0.003; and N, 0.0012. The impurity levels in the 0.23 pct P alloy are con-

Jan 1, 1968

By J. C. Jr. Vaughan

ALTHOUGH a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron are known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the Solubility Of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 1.5.5 per cent silicon.

Jan 1, 1939

By F. N. Koepel, L. A. Callaway

The property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, about 75 miles to the eastward from the port of Chafñaral. At this point the Andean system is made up of two principal ranges, and the mine and metallurgical plant are both on the westerly slope of the outer or western range. Mean elevation of the mine is 10,500 ft., while at the plant the elevation ranges from 9445 to 9700 ft. A meter gage railroad extends from the company&apos;s port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 94 miles, of which 57.79 miles are owned by the Andes Copper Mining Co. and the remainder of the road is controlled by the State. Development of the Potrerillos mine and installation of the metallurgical equipment presented unusual difficulties due to the arid nature of the country, high altitude and remoteness of the location from any considerable center of population. As a primary step it was necessary that railroad transportation be provided in order that mine development and plant construction could go forward on an economical basis. Provision of an adequate supply of water for domestic and metallurgical uses involved the construction of approximately 178 miles of pipe lines, all of which have their sources at altitudes ranging from 12,000 to 14,000 ft. above sea level and traverse rough and difficult terrane. Water for metallurgical use is brought to Potrerillos from the Ola River, a stream originating in the high cordillera to the eastward from the property. It is delivered by means of a steel pipe line, 32 miles long, having diameters ranging from 22 to 36 in. Domestic water is supplied to the various camps through a system of pipe lines aggregating 146 miles in length, the Ola water being unfit for this purpose. These conductors gather water from numerous springs in the high mountains to the eastward from Potrerillos and deliver it to the mine, the reduction works and the port at Barquito. Extensive permanent housing facilities had to be provided as it was necessary to care for more than 3000 workmen and employees at the

Jan 1, 1934

By Edgar Kidwell

To any one acquainted with the practical conditions surrounding the mining engineer and mine-manager, especially in this country, the presentation to the American Institute of Mining Engineers of a paper on the above subject will need no explanation. The members of this profession are continually called upon to design and erect, both above and underground, structures which involve the use of beams. Not to mention the various buildings connected with large mining operations, I need only refer, in support of this statement, to trestles, derricks, headworks, etc., on the surface, and to timbered stations and other spaces of large span in the mine-workings. Notwithstanding the rapidity with which iron and steel are replacing wood in the construction of large buildings, there will always be cases in which the use of metal will be unadvisable. Especially will this be true in districts remote from large cities. Works of temporary character will continue to use timber. High freight-charges, the liability of delays in delivering iron, and the temporary character of many of the structures, will for many years to come make it advantageous for the mines west of the Mississippi and on Lake Superior to construct their buildings almost exclusively of wood. The timber-resources of the country are decreasing so rapidly that already the engineer finds difficulty at times in obtaining beams of large size. This difficulty will steadily increase, and will force the constructor to resort more frequently to built-up beams, such as have long been used in Europe, owing to the difficulty of obtaining there such large sizes of timber as have

Jan 1, 1898

THE object of all classification is to group together things which are alike, and separate those which are unlike. This object is essentially a practical one, enabling us to apply past experience to new conditions: Many costly large-scale experiments lose half their importance for want of proper description of the coal used, and the consequent impossibility of predicting other coals will behave in the same way. I do not, therefore, make a fundamental distinction between "scientific" and "use" classifications, except in so far as use depends on conditions, such as size or impurities which are not related to the nature of the coal substance itself. The characters chosen to define the classes of coal must be such as are accompanied by as many other properties as possible. It is not to be expected that any system of classification will enable us to predict every property of coal, since all specimens have an individuality of their own. But specimens can be grouped by a number of resemblances into species. Further, species which resemble each other can be grouped into genera.

Jan 1, 1928

By Henry M. Howe

Jan 1, 1908

By Geoffrey Gilbert

A study of specimens shows that the key to both oxidation and enrichment at Duck-town is the behavior of pyrrhotite, which is in part dissolved and in part replaced by marcasite. Enrichment takes place chiefly at the expense of marcasite. THE material that forms the basis of this paper was collected in the spring of 1922, during a ten-day visit to Ducktown by the writer in the company of Prof. L. C. Graton. The time available for the work was far too short to allow anything like a thorough study of the deposits, and structural and stratigraphic questions, though they have an important bearing on the origin of the primary ores, were necessarily left untouched. Attention was focussed on the zone of oxidation and enrichment; and by devoting most of our time to the upper levels, open pits, and old workings, and examining the deeper levels only thoroughly enough to obtain a fair idea of the nature of the primary sulfide ore, we were able to make a reasonably complete survey of the various orebodies. With this field work for a background, the writer later made a study, in the Harvard laboratories, of the specimens obtained during the visit. As some of the facts brought to light by this study appear to be new, it seems worth while to set forth the outstanding features and a proposed explanation of them. Much of the Ducktown material that is obviously of greatest significance, as regards oxidation and enrichment, is soft and crumbly. Notwithstanding the desirability of gaining from such material all possible information as to its mineral composition and textural relationships, but little has heretofore been learned regarding it; but, by suitable preparation of this material in connection with the present study, it has been possible to examine it under the microscope without any disturbance of its texture and about as satisfactorily as if it were hard, fresh ore. The information thus gained has contributed measurably to the results set forth in this paper.

Jan 3, 1924

By D. S. Gleason, D. E. Severson, D. R. Skidmore

Pittsburg and Midway Coal Co. has modified the German Pott-Broche process, on which patents date back to 1927, to produce on a bench scale liquid products by solution hydrogenation of coal. A continuing program of lignite solution-hydro gena-tion experiments is directed toward investigating coal solution reactions, determining favorable conditions for the solution refining of lignite by the Pott-Broche process, and investigating some of the uses for the de-ashed product obtained from lignite The German Pott-Broche process1" on which patents date back to 1927, has been modified by the Pittsburg and Midway Coal Co., a Gulf Oil subsidiary, to produce on a bench scale liquid products by solution -hydrogena-tion of coal." The objectives of the present effort are to investigate coal solution reactions, to determine favorable conditions for the solution refining of lignite by the Pott-Broche process, and to investigate some of the uses for the de-ashed product obtained from lignite. This paper is a summary of results to date in a continuing program of lignite solution-hydrogenation experiments. The coal solution reaction program has several principal aims. The first of these is to determine whether lignite can be successfully dissolved in solvents that might be practical for commercial development. The second object is to determine whether the solvents function after successive cycles of use, recovery, and reuse. It seems necessary to the economics of a potential commercial process that the solvent be recycled. Third, it is desired to learn something about the distribution of the ash constituents between cake and filtrate. The extent of ash removal is important. The nature and quantity of mineral matter passing through the filter may determine end-use marketability. For certain use applications, trace quantities of certain minerals can be objectionable, e.g., titanium and vanadium must be very low in electrode carbon for aluminum production. The Solution Reaction The coal solution Process involves an extremely complex system of chemical reactions. An initial solvent such as anthracene oil is a mixture of hundreds of different compounds with a boiling range of roughly 500" to 750°F at atmospheric pressure. The coal macro-molecule is broken down by thermal decomposition and solvent action into myriads of different compounds, some the same as those comprising the solvent. This similarity in structures opens up the possibility of production and subsequent recovery of solvent. Some solvent is inevitably lost by reaction. Regeneration of solvent was not a problem in the early German Pott-Broche plant. The coal refinery was an integral part of a petroleum refinery complex and replacement solvent was readily available. A coal refinery using lignite, however, might be isolated from other hydrocarbon processing facilities and the regenerability of solvent could be vital to the economic success of the venture. Several structural features of the solvent molecules have been cited as important to the coal solution process.&apos;. The first of these is aromaticity of the material, the second, ability to transfer hydrogen to another molecule, as for example the ability of tetralin to transfer hydrogen and be converted to naphthalene. Finally, the presence of hydroxyl groups on aromatic rings within the molecule, i.e., phenolic character, seems beneficial. Mixtures of pure compounds have been tried by various investigators. Mixtures of o-cresol, a phenolic substance, and tetralin were found to dissolve bituminous coal better than either substance alone.3 This maximum solubility was not found with lignite." Hydrogen contributes to the reaction by hydro-genolysis and by combining with free radicals and molecular "loose ends" to stabilize the compounds formed in coal depolymerization. High boiling point, and correspondingly high molecular weight, seems to be a property which improves solution potential for coal with a given type of compound.&apos; The maceral components of the coal appear to have an important bearing on its ease of solution. The fusain portion is quite inert to solvent action, but the an-thraxylon material dissolves quite readily.3 The hydrogenation reaction can be improved by the use of a catalyst; commercial hydrogenation catalysts having been found effective. Although cost is involved in the use of catalyst and catalyst recovery, the resulting saving in time and perhaps lowered temperature or pressure might justify their use in the solution refining process and decrease the total process costs. Apparatus and Procedure The coal solution runs were made in a 1-gal stainless steel stirred autoclave. The autoclave was provided with thermocouple wells and a transducer to permit continuous recording of temperature and pressure. The autoclave stirrer was magnetically driven, eliminating the leakage inherent with a rotating pressure seal. For runs in which a catalyst was used, the catalyst in the form of beads was placed in a wire mesh container mounted on the stirrer shaft. A control system programmed the heatup and reaction cycle. The permissible heating rate was 5°F per min because of the need to minimize thermal stress in the autoclave body. The temperature was raised at that rate until the reaction temperature was attained and then the temperature was held constant for the desired length of time. The maximum temperature seldom exceeded the average run temperature by more than 15°F.

Jan 1, 1971

By J. L. Bruce

After six years of war-enforced idleness, Cyprus copper mines are operating again. This relatively long shutdown seems infinitesimal when compared with something like seventeen hundred years of inactivity that followed the important operations of the ancient Romans, and continued until the twentieth century. The historical records of the ancient operators are scarce but full of interest to those who realize that Cyprus copper production was important more than two thousand years ago. This paper, however, will give only a brief review of the ancient history and the evidence of ancient mining which have been quite fully covered in other publications.1-6 The purpose of this paper is to give a general sketch of the Cyprus Mines Corporation&apos;s enterprise in the Island of Cyprus, with special emphasis on those conditions and practices which are unusual. The picture is not intended to be complete, and many interesting details will be omitted. Some of these may be described in subsequent papers covering departmental practices. The principal operations of Cyprus Mines Corp. are in Cyprus, where it has leasehold concessions from the Cyprus Government covering about 50 square miles. It holds additional areas under "Prospecting Permits." The consideration for the concessions is a royalty on production, coupled with minimum annual rentals. Cyprus is a British Colony in the Eastern end of the Mediterranean with an area of about 3000 square miles and a population of about 400,000, of which 65 pct may be classed as Greeks on the basis of language, religious training, and traditions. About 25 pct are Moslems, principally of Turkish extraction. Prevailing languages are Greek and Turkish. A large proportion of the supervisory and administrative staff and practically all of the skilled and unskilled craftsmen and laborers are drawn from the native population. The "overseas" staff constitutes not more than 2 pct of the employees. The majority of these are from the United Kingdom, the British Dominions and Colonies. About one-third are from the United States of America. The topography of the Island is rugged, with mountains and foothills covering more than two-thirds of the area. Between the Kyrenea range rising to 3000-ft elevation, along the north coast, and the Troodos range (maximum elevation 6400 ft) occupying the southwest half of the Island, lies a cultivated rolling plain, the "Mesaoria," dry in summer and watered only by the winter rains and by scanty irrigation from small mountain streams and wells in the spring and summer. Climate and natural vegetation are characteristic of semi-arid conditions. The "urban" population, about one-fourth of the total, lives in the five port towns, Famagusta, Larnaca, Limassol, Paphos and Kyrenia, and in the capitol Nicosia, near the center of the Island. The suburban population lives almost entirely in villages or small towns, with very few people residing in isolated country homes.

Jan 1, 1949

By George B. Clark

7.1-1. Introduction. The fundamentals of blasting involve both the properties of explosives and of the rock being blasted. While the knowledge of property correlation between rocks and explosives for most effective blasting is far more complete, many quantitative evaluations have been made. Four of the most important explosive properties appear to be energy density, bulk density, rate of energy release, and the pressure-time history of the gases produced. Important rock properties are density and porosity strength, and energy absorption properties, including the effective moduli of elasticity. Rock structure also has a marked effect on its breaking properties, i.e., joints, bedding, fractures, alteration, etc. Several mechanisms enter into rock fragmentation by blasting. These include slabbing, radial fracturing, crushing, and bursting by the gas bubble. All of these factors are closely related to properties of both explosives and rock. Slabbing depends upon the character of the first generated stress wave, whose shape and magnitude are a result of the pressure generated by the explosive, its time history, and the resultant response of the rock, including its ability to sustain the stress wave. Actual slabbing, in turn, is a function of the magnitude and shape of the pressure pulse and the tensile strength of rock. Further fragmentation depends to a great extent upon the amount of gas in the bubble and its energy and pressure. Blasting rounds are best designed by taking the above factors into consideration. This is effectively accomplished by use of cratering curves which relate breakage- parameters to the explosive energy. Optimum depths from single charge cratering curves must be adjusted to changes in shot geometry and related to multiple hole blasting. Blasting damage may occur from either air blast or ground waves, and in the latter ease may be due to direct vibration or to settlement caused by vibration. Technical information indicates that blasting damage is often

Jan 1, 1968

By C. E. Corson

The experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of&apos; annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent. of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to

Jan 1, 1907

By Charles Baker

THE district of Catorce, San Luis Potosi, ranks among the first half-dozen silver-producing camps f Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapum, Mazapil, Palomas, Musquiz, Minas Virjas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (609.6 m.) in 4 1/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catorce from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catorce, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to erosive forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstones, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains; some f this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution f the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebbles, and finer detritus.

Jan 9, 1921