Search Documents

By Gary E. Melickian

Last year's review was characterized as a year of politics and began an era of legislation. The 1972 review can be similarly characterized, with even more rigid health and safety regulations and environmental legislation. The mining industry should be aware of what's happening in the nuclear power and other fields as a result of the National Environmental Policy Act (NEPA) of 1969, where the environmental impact of most major construction activities are already under close scrutiny. Section 102 of NEPA requires that all federal agencies include a detailed statement on specified environmental conditions as part of every report on proposed actions significantly affecting the quality of the human environment. All such environmental reports must consider the same general conditions: • The environmental impact of the proposed action. • Any adverse environmental effects which cannot be avoided should the proposal be implemented. • Alternatives to the proposed action. • The relationship between local short-term uses of man's environment and the maintenance and enhancement of long-term productivity. • Any irreversible and irretrievable commitments of resources which would be involved in the proposed action should it be implemented.

Jan 2, 1973

By L. D. Fetterolf

The New Jersey Zinc Zompany operates at Depue, Illinois, an integrated zinc smelting plant using tie vertical retort reduction process. The overall operation comprises green concentrate roasting, sintering, vertical retort smelting and metal refining. In the roasting operation, the fine concentrate is pelletized, the dried pellets fluidized and autogenously roasted with air in a “fluid column” with minimal formation of dust requiring recirculation. The roasted pellets and any associated roaster dust are agglomerated in a rotating drum and laid down, in combination with coal for fuel, on a Dwight-Lloyd sintering machine which converts to a semi-fused mass - a physical state more suitable for vertical retort smelting. The smeltins plant of 27 vertical retorts rated at 8 T zinc each per day on average requires the following major processing steps - mix preparation and briquettine, briquet coking, vertical retort reduction, vapor condensation and slab casting of metal. A portion of zinc production is converted to 99.99+ percent purity by boiling and fractional distillation in columns consisting of externally heated, superimposed trays of high-conductivity refractory.

Jan 1, 1970

By H. J. O’Donnell, B. C. Parks

IN 1930 the late Dr. Reinhardt Thiessen set up a method of microscopic analysis and type classification of coal that has since been followed as standard practice in the coal-petrography laboratory of the Bureau of Mines. Thiessen's terminology which designated the constituent parts of coal in terms of botanical origin was introduced in 1920.l The technique, however, of preparing a completely representative series of thin sections from a column sample of coal for use in making quantitative determinations of coal components with a microscope was developed about 10 years later by Thiessen and coworkers G. C. Sprunk and H. J. O'Donnell.2 Complete thin-section analyses subsequently have been made of 126 column samples of various ranks and types of American coals. The data and information were assembled from these thin-section studies and published in a large number of reports dealing chiefly with investigations of the coking and hydrogenation properties of certain American coals. In the years following adoption of Thiessen's method, a considerable amount of work was done in collecting column samples of many coals, making routine thin-section analyses of these, interpreting the results, and finding practical application for the information in other fields of coal research. The many reports and papers covering the work in coal petrography, however, offer very little discussion that can be considered as critical appraisal of the technique. Criticism outside the Bureau most often has voiced questioning opinions concerning the accuracy of the method used of measuring coal components microscopically and classifying the coal into arbitrary types on the basis of the quantitative determinations. The principal purpose of this paper is to discuss in some detail and present data showing the results of certain investigative work done in the petrography laboratory on the accuracy of the Bureau's method of microscopic measurement of components in coal thin sections. Data from microscopic analyses on file made by G. C. Sprunk and H. J. O'Donnell were freely used in the investigation, and a table of columnar analyses from an unpublished manuscript by Sprunk is included in this paper for reference. In the course of the experimental work a method was developed for measuring instrumentally with a planimeter the components shown in micrographs of selected thin sections. Measuring coal components with a planimeter furnished useful information for studying the accuracy of microscopically measuring the same components in thin sections. PETROGRAPHIC COMPONENTS AND TYPE CLASSIFICATION OF COAL Thiessen considered coal to be composed of two visibly different major components present in various types of coal in greatly varying proportions. He named

Jan 1, 1948

By William Fink

THE constitution of the aluminum-cobalt alloys has been the subject of relatively few investigations. Brunck1 analyzed the residue which remained after treating the 17 per cent cobalt alloy with dilute hydrochloric acid. The results of the analyses indicated the existence of a compound Co3Al13. Guillet2 published a liquidus for the aluminum-cobalt system which contained two maxima corresponding to CoAl6 and CoAl2 and two eutectic points at 30 and 74 per cent Co. The most extensive investigation of the system was carried out by Gwyer,3 whose results are summarized in Fig. 1. It will be noted that at the aluminum end there is a suppressed eutectic at 644° C. By extrapolation of the duration of the eutectic arrest to zero, the composition of the compound was placed at Co3Al13. Another thermal arrest was noted at 550° C., which Gwyer attributed to a peritectic reaction. The present investigation of the aluminum end of the aluminum-cobalt system is the eleventh of a series dealing with the constitution of aluminum; rich alloys prepared from electrolytically refined aluminum.4 Preparation of Alloys.-The alloys used in this work were all prepared from electrolytically refined aluminum, the analysis of which is shown in Table 1. In preparing some of the alloys, metallic cobalt (98 to 99 per cent) was used either directly or in the form of an intermediate alloy, the composition of which is given in Table 1. In order to obtain alloys of higher purity, cobalt was introduced into some of the alloys by means of chemically pure cobaltous chloride which was readily reduced by the aluminum. A small electric furnace with nickel-chromium heating elements was used in the preparation of the alloys.

Jan 1, 1932

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Brian F. Dyson

The surface tensions at 1550°C of some Fe-S alloys (in the range 0.008 to 0.052 wt pct S), Fe-Sn alloys (0.31 to 48.4 wt pct Sn), Fe-P alloys (0.038 to 2.38 wt pct P), Fe-Cu alloys (2.15 to 22.8 wt pct Cu), and Fe-1 pct C-S alloys (0.005 to 0.076 wt pct S) along with the surface tension of the base iron have been measured by the sessile-drop method. A mean value of 1754 dynes per cm was found for the surface tension of the base iron. Sulfur was found to be highly surface-active, the surface-tension results being in quantitative agreement with existing data. Tin and copper were found to be less surface-active than sulfur while phosphoms was completely nonsurface-active. The surface tensions of Fe-1 pct C-S alloys were found to be lower than those of the Fe-S alloys containing the same sulfur content. This was shown to be a mmzifestation of the increase in the thermodynamic activity of suZfur by carbon. It is only in recent years that attempts have been made to measure the surface tension of liquid iron of known high purity.1-3 Earlier measurements4-7 were made on liquid iron containing variable amounts of what are now known to be surface -active solutes. The exact value of the surface tension of liquid iron is still, however, open to some doubt. Halden and Kingery' reported a value of 1720k 34 dynes per cm at 1570°C, Kozakevitch and Urbain8 gave 1790k 25 dynes per cm at 1550°C, while Van-Tszin-Tan et al. obtained a value of 1865k 37 dynes per cm at 1550°C. The first systematic investigation into the effect of controlled solute additions on the surface tension of iron was made by Halden and Kingery.' They showed that sulfur and oxygen were highly surface-active, whereas nitrogen was only slightly active, and carbon inactive. A subsequent investigation by Kingery indicated that two other group-6B elements, selenium and tellurium, were also surface-active. This highly surface-active nature of sulfur and oxygen has recently been substantiated by Kozakevitch and Urbainla and Van-Tszin-Tan et al. l1 Kozakevitch and Urbainl2 have also conducted an experimental survey of the effects of a number of metals on the surface tension of liquid iron. Their surface-active nature was, in all cases, less than that of the group 6B elements. The present investigation was undertaken to study in more detail the surface tensions of dilute Fe-S alloys and to measure the surface tensions of binary alloys of iron containing phosphorus, copper, and tin. The effect of sulfur additions on the surface tension of Fe-1 pct C alloys was also determined. EXPERIMENTAL PROCEDURE The sessile-drop method was employed in the present investigation. An apparatus was built similar in principle to that described by Humenik and Kingery.lS It consisted of a horizontal silica tube, which could be evacuated to pressures less than 10-5 torr, with its central portion surrounded by a water jacket within which was a high-frequency coil. This generated heat in a tantalum susceptor placed inside the silica tube, which in turn radiated heat to the specimen mounted on a recrystallized alumina plaque. Temperatures were measured by an optical pyrometer and photographs of the molten drop were taken on a fixed-focus plate camera giving a magnification of X2. Surface-tension values were determined from the resultant drop using the method described by Baes and Kellogg.l4 The high vapor pressure of molten iron made it necessary to conduct all the experiments under a 1/4 atm of argon (greater than 99.995 pct purity). The analysis of the base iron used in the investigation is given in Table I. Each sample was approximately 3 g in weight and had a hemispherical base to ensure a uniform advancing contact angle on melting. The iron alloys were prepared individually in the sessile-drop apparatus by drilling a hole in the top of each sample and adding the required amount of solute, the drops being analyzed after the experiment. This method of preparation had the advantage of ensuring a consistent minimal contamination by oxygen due to refractory attack and also allowed surface tension to be measured at the same time. Every precaution was taken to ensure that the specimen was not contaminated by grease when it was introduced into the apparatus, the samples being cleaned in acid, dried in alcohol, and rinsed in petroleum ether. All handling was done with tweezers. Once the specimen had been placed inside the susceptor, the furnace was evacuated and the Sample leveled. The furnace was then degassed at approximately 1000"C before the argon was introduced. In every case the surface tension was determined at 1550" C.

Jan 1, 1963

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By W. M. Weigel

The general term "sand" applies to a multitude of similar materials consisting of fine granular mineral. As usually understood, it means the ordinary natural product used for structural purposes and made up largely of grains of quartz. Quartz sand constitutes by far the greater bulk of the production, but there are other grades used for industrial purposes, such as molding sand, glass sand and many others, that may be grouped under the general name of special sands. Under this general group would fall filter sand, sand-blast sand, engine sand, potter's sand, abrasive sands of all kinds, sand for pulverizing, roofing sand, flooring sand, fire or furnace sand, standard sand, burnishing sand, sand for magnesium oxychloride cement-plasters and sand for chemical and metallurgical purposes. Sources of Supply Sand is a widely distributed natural product and even the better grades are low-priced commodities. For these reasons development has occurred near points of consumption where sand meeting the requirements is available. Some special grades, however, cannot be prepared from any sand bed and shipments are often made over considerable distances when the only developed deposit is remote from the consuming center. This is true of filter sand, sand-blast sand, sand for pulverizing and some of the others when chemical purity or grain size, coupled with the need of a properly equipped plant for preparation, are required. New Jersey is a large producer of filter, engine, sand-blast, fire, and pulverizing sand. Pennsylvania, and West Virginia produce special sands for pulverizing, fire sand, abrasive sand, engine sand and sand for chemical and metallurgical use. Ohio produces much sand-blast, fire and abrasive sand, and some filter sand. Illinois and Minnesota produce

Jan 1, 1926

By S. B. King

IT is the purpose of this article to give those not familiar with the subject an idea of the extent to which coal is mined by machine in the United States; to describe some types of electrically operated coal cutters; and in particular, some of the latest improvements and developments in these machines. Generally speaking, the article deals with the mining of bituminous coal in room-and-pillar mines, as the use of undercutting machines in the anthracite region of Pennsylvania is in its infancy, and when machine mining is referred to bituminous coal is taken for granted. The number of mines in the United States that are operating on the long-wall principle is very limited, and the number of long-wall machines in use is a very small percentage of the total. The advantages of mining by machine may be summed up briefly as follows: A. Increased safety to property and life, due to the large decrease in the amount of powder required when the coal is properly undermined. B. Reduction in the cost of mining. C. Improvement in the quality of the product; and, consequently, increase in market value, due to the greater proportion of lump and screen sizes secured by machine mining. D. Increase in the capacity of the mine, and more rapid development of new mines. E. Ability to mine veins in which the height of the coal or the character of the roof has prevented mining by hand, on a commercial basis.

Jan 6, 1914

By H. S. Rawdon

One of the most vital problems in the manufacture of steel at present is the occurrence of the defects that have been popularly termed "snow flakes," "flakes," or "scabs." Particularly is this the problem of many manufacturers who, during the past 2 yr., have undertaken large-scale production for the first time. A study of the microstructure of such defective material throws considerable light upon the nature of these defects and is essential before measurcs may be taken for the elimination of the defects. Flakes do not appear to be found in the plain carbon steels; they have been found. however, in abundance in some of the simple alloy steels that are being used in such vast quantities; vie., nickel steel of the approximate composition, 0.40 carbon and 3.5 per cent. nickel, and in the chrome-nickel type. The present article summarizes the characteristic features of defective steel of the flaky type as they have been found by laboratory study of numerous specimens, and it aims to show the conditions within the metal that are favorable to the occurrence of this type of defect without entering into the details of mill practice (size of ingot, design of molds, rate of cooling, distribution of cooling stresses, etc.), all of which conditions appear to play a role in the production of these defects. MacrostrUctURe To one familar with flaky steel, the appearance of "snow-flakes" is unmistakable and is not to be confused with other types of defects. Figs. 1 to 6 show the appearance of fractures of steel showing this type of defect; the white silvery area, which always has the appearance of being of a very coarsely crystalline structure, in the specimen stands out in bold contrast to the darker background and readily justifies the use of the term "snow-flakes." Fig. 1 shows the appearance of the faces of the two halves of a nickel-steel forging that has been split to show the interior flakes. Fig. 2 is a nickel-steel bar (carbon 0.40 per cent.,

Jan 1, 1920

By Edward C. Mack, Ronald G. Stovash

INTRODUCTION Ronald G. Stovash General Superintendent Consolidation Coal Company Shoemaker Mine Moundsville, West Virginia Consolidation Coal Company's Shoemaker Mine is located in West Virginia's Northern panhandle near Wheeling, adjacent to the Ohio River. Steam coal is mined from the Pittsburgh #8 seam which averages 65 in. in thickness. The 10 in. of draw rock directly above the coal is taken on advancement, but remains when longwalled. The top consists of up to 12 in. of lower quality coal, and immediately over that, up to 10 ft of multi layered shales, coal, and bone. The cover ranges from 300 to 800 ft of shales and limestone. Two longwalls operate in the mine. The first longwall started in April 1975 and is retreating its eighth panel. This wall was the first to use shield supports in the United States. The second longwall started in September 1979 and is currently retreating its first 7,000 ft panel.

Jan 1, 1981

By Sir Nathaniel Barnaby

We must not conceal from ourselves that, against the perils arising from perforation of the shells or hulls of ships, we are greatly worse off in these days of steel and iron than we were when our ships were built of oak, teak and pine. Apart from the greater

Jan 1, 1891

Arthur H. Elliott, New York, N. Y.: We have all been very much interested in the results of Dr. Bone's work, which Mr. Ellis has presented to us this evening. The high temperatures attained by this method perhaps afford us an explanation of the temperatures reached in the puddling-furnace with its crude and almost primitive methods of burning fuel, by means of which we have, nevertheless, been able to melt iron in a comparatively short time, and keep it in a molten condition down to a high degree of purity. No doubt many of us have wondered, as I have done, how such a result could be obtained in such a way; and it occurs to me that, perhaps, Dr. Bone has supplied the explanation in disclosing the effect on combustion of burning gas and air after passing through, and in contact with, a porous refractory body. May not the fettling of the puddling-furnace have, in some degree, an effect upon the combustion like the influence of the porous diaphragm employed by Dr. Bone ?

Jan 1, 1913

PRACTICAL PROBLEMS AND BASIC PRINCIPLES ranging from ore testing to cost estimation get a working over from top men in the minerals beneficiation field. The Minerals Beneficiation Division developed this symposium for presentation at the 1953 Los Angeles General Meeting to assist the many people who think that having a new plant necessitates a lot of trouble and dismay. The papers and free discussion from the floor give ways and means of approaching a new plant that will relieve the strain on the organization, if adequate attention is put on the program before work begins - that is if thought is given to the program itself, before tackling the actual mill design.

Jan 9, 1953

By R. S. Schechter, T. R. Guilinger, P. Bobeck, J. G. Price, L. W. Lake

This paper presents the results of an experimental study on the rate of uranium and molybdenum extraction from a flow reactor. Specific variables tested are fluid throughput and flow rate, lixiviant cation, and injected pH and carbonate concentration. The ore tested was from the Felder mine in southern Texas. It contained substantial quantities of marcasite and molybdenum disulfide that competed with the uranium ore for oxidant. Flow studies showed the oxidation of molybdenum disulfide under field conditions is mass transfer controlled, whereas the uranium oxidation is limited by surface reaction rate. The rate of uranium oxidation decreased with decreasing pH. The total carbonate levels, on the other hand, were unimportant. Ammonium carbonate appears to greatly decrease, if not completely halt, the reaction of marcasite with the oxygen. This effect was not found using either sodium or potassium carbonate.

Jan 1, 1986

By C Gunther

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By D. W. Brunton

The object of the investigations and experiments here recorded was to obtain such information and data as would make it possible to determine the fineness to which crushing must be carried, in sampling gold- and silver-ores, in order to obtain results within an allowable limit of error.

Jan 1, 1896

By Samuel S. Wyer

The following abbreviations hare been used in the text: Am. Mfr. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rez;. Canadian Mininy Review, Ottawa, Can. Cuss. Mag. Cassier's Mayazine, New York, N. Y. Col. Eng. Colliery Engineer, Scranton, Pa. Col. Guard. Colliery Guardian, London, Eog. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and 8. I. Journal of the Iron and Steel Institute, London, Eng. Jour. W. Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester. Zeitsch f. Berg u. Hüt. Oesterreichische Zeitschrift für Berg-und Hittenwesen, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C! E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N. I!. Duns. Fed. I. M. E, Transuctions Federated Institute Mining Engineers, Newcastle-on-Tgne, England. Trans. L 31. E. Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Jan 1, 1907