Search Documents

By J. A. Bownocker

THE Pittsburgh is one of the most important coal beds of Ohio. It was the last of the great coal beds to be worked extensively in that State, has the largest area of virgin coal, and will in all probability be the last of the great deposits to be exhausted. The line of outcrop sweeps nearly southwest in a sinuous line from Jefferson County on the north to Lawrence on the south, a distance on a bee-line of at least 150 miles. (Fig. 1.) The maximum width of the area under which this coal is due is about 55 miles, but in most places it is less than half that and in the two southern counties it is in places restricted to narrow ridges. Here as elsewhere the Pittsburgh coal forms the base of the Monongahela formation, and the following section taken from Condit shows the position of this bed with reference to certain higher ones in this field:1 FEET INCHES Shales and thin beds of limestone 24 5 Coal, Meigs Creek, No. 9 4 0 Shale, sandy 11 0 Coal 0 8 Shale, clayey 6 0 Coal, Lower Meigs Creek 3 0 Shales,clayey 2 0 Limestones and thin layers of clay 25 0 Unseen 11 0 Coal, Redstone 2 0 Unseen 11 0 Coal, Pittsburgh, No. 8 8 0 Clay 5 0 Limestone 4 0 From the standpoint of continuity the Pittsburgh coal of Ohio must be classed with the patchy type. As the map shows, the coal is thin or wanting along many miles of the line of outcrop. The large deposits form three separate areas, which, in order of their importance, are generally known as (1) the Belmont, (2) the Federal Creek, and (3) the Gallia fields.

Jan 10, 1926

By Robert Maes, Robert de Strycker

The Fe-Ni-As phase diagram has been established by the study of about a hundred alloys, by microscopic observation, and by thermal analysis, with arsenic contents up to 50 pct. The iron and nickel arsenides present extensive solid-solution fields, owing to the substitution of nickel by iron and vice versa; the extent of the solubility field of each compound has been determined with an accuracy of ±1 pct. In the investigated range of compositions, the solidification reactions were established, and the temperatures of the invariant reaclions detevmined with a preciston of iZ°C in the most favorable and ±5°C in the least favorable cases. The isothermal lines of the liquidus surface have also been drazum, with an accuracy estimated at i5°C. Reactions in the solid state, which take place for the formation or the decomposition of certain phases , were investigated in detail. ThE constitution diagram of the Fe-Ni-As system is fundamental for the understanding of the properties of nickel speiss; these by-products of the extraction of certain nonferrous metals indeed often contain the three elements iron, nickel, and arsenic as main constituents. The Fe-Ni-As system has already been the object of earlier investigations. In 1932, Guertler and Savels-berg' have presented some elements of the ternary phase diagram, for arsenic contents up to 55 pct (all percentages in this paper are given in weight percent), including the vertical section FezAs-Ni&s2. This investigation is, however, incomplete and certain anomalies suggested the necessity to verify the results published by these authors: the section Fe2As-Ni5AsZ, for example, is presented as quasi-binary, with a field of complete miscibility in the solid state, even though these compounds do not have the same structure. Recently, ~useck' established an isothermal section at 800°C in the Fe-Ni-As system by X-ray diffraction and microscopic examination of water-quenched alloys. These techniques are sometimes inaccurate for the determination of the fields where alloys are liquid at the investigated temperature, and they may lead to erroneous conclusions when a compound exists at the investigated temperature but is not stable at room temperature and cannot be maintained by quenching. LIMITING BINARY PHASE DIAGRAMS The Fe-As constitution diagram has been the object of several investigations which have been reviewed by Hansen and Anderko.3 For the Ni-As phase diagram, a recent study has been effected by Yund.4 In this system, Heyding and calvert5 have determined the existence of a compound of unidentified structure at arsenic contents slightly higher than those corresponding to Ni5As2 and at temperatures lower than about 200°C; by analogy with iron and cobalt arsenides, this compound could correspond to the formula Ni2As, as suggested by Kulle-rud; although this is not definitely established. In the region of arsenic contents from 35 to 55 pct, Fried-rich7 detected anomalies in the solidification reactions; an interpretation of these anomalies was given by Hansen ,8 which assumed that the solidification reactions in practice are not in equilibrium, but are meta-stable. The main features of the Fe-Ni constitution diagram are the existence of a complete miscibility field, at least at high temperatures, for the fcc phase (which will be designated by My in the remainder of this work) and of a limited solubility field for the bcc phase (designated by Ma). EXPERIMENTAL METHODS The fundamental technique used in this investigation was microscopic observation, which allowed the determination of the reactions occurring during solidification of the alloys, and possible reactions in the solid state.

Jan 1, 1968

By Joseph R. Stephens

Deformation substructures of' polycrystalline tungsten, W-2, 9, and 24 pct Re, and W-3 pct Ta were studied by tra?zsrnission electron microscopy. The stress-strain curve for unalloyed tungsten showed gradual yielding followed by work-hardening. Electron nzicrographs indicated a gradual increase in dislocation density with increase in strain up to 5.0 pct. Dislocations, although frequently jogged, were straight over moderate distances and were in a randorn array. Stress-strain curves for alloy specimens of W-2 and 9 pct Re and W-3 pct Ta exhibited a drop in stress at yielding followed by only slight work-hardening. Electron micrographs of these specimens after strains of 0.05, 0.1, and 0.5 pct revealed no change in dislocation substructure from the unstrained specimens. After 2.0 pct strain, the three alloys exhibited dense networks. W-3 pct Ta was characterized by straight, frequently jogged dislocations comparable with the dislocation structure in unalloyed tungsten after a similar amount of strain. In contrast, W-2 pct Re exhibited dislocations that contained widely spaced jogs, while W-9 pct Re had developed a cell structure after the relatively srnall strain of 2.0 pct. The W-24 pct Re alloy contained a few dislocations after 0.1 pct strain, while after 0.5 pct strain twins were evident. Dislocation slip bands apparently preceded the twins. The stress-strain curve for the alloy indicated that twinning commenced after approximately 0.25 pet strain. These results indicate that the primary effect of low rhenium concentrations (2 and 9 pct) in tungsten is to increase dislocation multiplication after macroyielding by reducing the Peierls-Nabarro force (lattice resistance to dislocation motion). The dislocation bands that precede twins in W-24 pct Re may be caused by localized internal stresses resulting fro a metastable structure, for example, clustering of rhenium atoms. The effect of high rhenium additions (22 a 65 pet* Rproperties of tungsten. Klopp, Witzke, and Raffo5 reported bend transition temperatures as low as -100°F (200°K) for dilute electron-beam-melted W-Re alloys tested in the worked condition. Recrystalliza-tion increased the bend transition temperature, but alloys with 2 to 4 pct Re were still markedly superior to unalloyed tungsten. Fractographic examinations of tungsten and W- 3 pct Re and W- 5 pct Re alloys by Gilbert 6 revealed that these low rhenium alloys showed a greater tendency toward cleavage failure than did tungsten. Garfinkle 7 showed that rhenium additions, up to 9 pct, to (100) oriented tungsten single crystals increased the proportional limit stress and decreased the flow stress and the rate of work-hardening. In addition, while deformation in unalloyed (100) oriented crystals apparently involved both (110)100) and (112) slip, crystals with rhenium contents of 5 andpct or more deformed primarily by (112) slip. The mechanism by which high and low rhenium additions affect the mechanical properties of tungsten is still not well-established. The present investigation was undertaken to determine by transmission electron microscopy the effects of low rhenium additions, 2 and 9 pct, and a high rhenium addition, 24 pct, on dislocation substructure in the early stages of deformation of polycrystalline electron-beam-melted tungsten. Unalloyed tungsten and a W- 3 pct Ta alloy were included for comparison. EXPERIMENTAL PROCEDURES Materials. Triple electron-beam-melted tungsten, W-2, 9, and 24 pct Re, and W- pet Ta were used for this investigation. Chemical analyses of the cast ingots are given in Table I. A description of the starting metal powders and melting and fabrication pro-cedures for unalloyed tungsten and the W-Re alloys is reported.5 The W-3 pet Ta alloy was processed in a similar manner. Compression specimens measuring 0.300 in. (7.6 mm) in length by 0.130 in. (3.3 mm) in diam were machined from swaged rods. All alloy specimens were annealed in a vacuum of 8 x 10- 6 Torr (10'2iVper sq m) for 1 hr at 3600°F (2255°K). The recrystallized grain size ranged from 0.06 to 0.08 mm diam for the alloy specimens. Unalloyed tungsten was annealed at 2400° F (1589°K) for 1 hr to produce a recrystallized grain diameter of approximately 0.12 mm. Specimens were electropolished in a 2 pet NaOH solution to a diameter of 0.125 in. (3.18 mm) to remove surface notches resulting from grinding and to improve reproducibility of t data. The ends o the compression specimens were ground flat, parallel to each other, and perpendicular to the longitudinal axes with 4/0 emery paper. Compression Tests. The compressive stress-strain apparatus used for compression tests is described in detail by Stearns and Gotsky.9 Room-temperature compression tests were conducted at a crosshead speed of 0.01 in. per min (0.25 mm per min).

Jan 1, 1969

By C. P. Proctor, J. T. Crawford

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium .about 1841. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing' in the nineteenth century. Chapman and Mott describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan; Lodge, Elliott, Blackett, and Murton. , The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as Rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mm. (13/15 to 5/16 in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product

Jan 1, 1943

By Klaus Schwerdtfeger

The rules of solution of oxygen from H2O-H2-He gas and of nitrogen from N2-H2 gas in shallow melts of liquid iron were measured at 1610o and 1600o C, respectiuely. Concentration profiles were detemined in the liquid iron. Tire rate data indicate that the solution process is controlled by diffusion in the iron melt. The diffusivities for oxygen and nitrogen in liquid iron, as calculated from the present data, are DFe-o = (12 ± 3) < 10-5 sq cm per sec and DFe-N = 11 ± 2) X 10-5 sq cm per sec at the temperatures employed. AN attempt was made by Shurygin and Kryukl to measure the diffusivity of oxygen in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was measured. Assuming that the rate of dissolution of silica is controlled by diffusion of oxygen in the iron, the oxygen diffusivity was computed from the rate data giving Dfe-0 = 6.1 X 5 sq cm per sec at 1600°C. Although this value seems to be of the right order of magnitude, there is no proof of the correctness of the assumptions involved in the interpretation of these rate data. The oxygen concentration in the iron at the iron-iron silicate interface was taken to be that in equilibrium with the silica-saturated silicate melt. That is, it was assumed that no concentration gradient existed in the liquid silicate. This is a questionable assumption, unless it is proved that the thickness of the silicate layer is very much smaller than that of the diffusion boundary layer in the iron. Furthermore, Shurygin et al.1 used the Levich equation2 to interpret their rate data. This equation was derived for mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich&apos;s derivations. In the present work the diffusivities of oxygen and nitrogen in liquid iron were measured at 1610" and 1600oC, respectively. EXPERIMENTAL METHOD Iron melts contained in high-purity gas-tight alumina crucibles were reacted with H2O-H2-He gas for the determination of the oxygen diffusivity and with N2-H2 gas for the determination of nitrogen diffusivity. At the end of the reaction period, the samples were quenched in a cold H2-He gas stream at the top of the furnace. Oxygen or nitrogen contents in the iron were determined by chemical analysis. Two different types of diffusion experiments were perforxed. To determine concentration profiles, a few rate measurements were made using 4-cm-deep melts. The solidified samples were sliced into discs and each disc was analyzed for oxygen or nitrogen. In another series of experiments, oxygen or nitrogen was diffused into shallow melts (about 0.5 to 1 cm in depth) and the total sample was analyzed to obtain an average concentration of the diffusate. In most experiments, 4- to 5-mm-ID alumina crucibles were used. Some experiments were also made in smaller (3 mm) and larger (7 mm) diam crucibles. This variation in diameter caused no difference in the reaction rate, within the limits of experimental uncertainty. To promote the establishment of a stable density profile in the melt, all the samples were suspended in the lower end of the hot zone so that the top of the melt was hotter by a few degrees. Molybdenum wire resistance heating was used. The reaction tube of the furnace was a gas-tight recrystal-lized alumina tube. In most experiments the furnace was heated by an ac power supply. To check the possibility of inductive stirring, some experiments were carried out in a dc operated furnace, with essentially the same results. The temperature of the furnace was controlled automatically in the usual manner. The temperature was measured with a Pt/Pt-10 pet Rh thermocouple and is estimated to be accurate within ±5°C. The iron used was prepared by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zir-conia crucible. The main impurities are: Si 0.004 pct P, S <0.002 pct Cr 0.005 pct N 0.001 pct Zr 0.002 pct O 0.003 pct Mn 0.004 pct C 0.002 pct The gas composition was controlled by constant pressure head capillary flowmeters. Oxygen was removed from the gas mixture by passing it through columns of platinized asbestos (450°C) and anhydrone. Selected H2O contents were obtained by passing the purified gas through oxalic acid dihydrate-anhydrous oxalic acid mixtures held at constant temperature in a water bath. Water vapor pressure data for the oxalic acid dihydrate-anhydrous oxalic acid equilibrium were taken from the 1iterature.3 The flow rate used was about 1.5 liters per min. The whole system was checked for tightness at regular intervals.

Jan 1, 1968

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By Robert Pike

THE first authentic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1.869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is said to have worked out his process. Jacobi1 in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein&apos;s process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeSO4 + (NH4)2S04. Lenz2 described ?some properties of electrolytically precipitated iron. He used Klein&apos;s bath, FeSO4 + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By James B. Cathcart

Marine phosphorite deposits occur in Braxil, in the Bambui Group of late Precambrian or Early Cambrian age. The phosphorite is laminated, isoclinally folded, and is composed of black, elongated apatite pellets and quartz grains cemented by quartz and muscovite. Abundant, narrow quartz veinlets cut through the .rock at right angles to the elongation direction of the pellets. The phosphorite is 0 to 80 m thick and contains 5 to 30 percent P2O5. The deposit is elongate towards the northeast, and the central, thickest, and richest part is bounded by faults. Measured reserves are about 250 million tons that average a bout 13 % P205. Preliminary testing indicates that grinding, scrubbing, and desliming will produce a material usable for fertilizer manufacture at a cost competitive with imported phosphate fertilizers.

Jan 1, 1979

By Murray Kaufman

Using en; 41 for a base alloy, 15 modifications were made in sheet form. The elements Al, Ti, C, Mo, Co, and Cb were varied. The effects on the phases formed and their temperature dependence, the aging characteristics, tensile and stress-rup- ture properties, and weld cracking were determined. The A1-Ti content and balance is the most important factor influencing the major sCrengthening phases [Ni,Ti and Ni,(Al, Ti)] and, consequently, mechanical properties. THE mechanical properties, fabricating and joining characteristics, dimensional stability, and so forth, of alloys containing secondary phases are largely determined by the phases present, their distribution, and their temperature dependence. The phases in the basic ternary and quaternary Ni-Cr-Al-Ti combina- tions have been investigated thoroughly.&apos;* The phase behavior of many commercial nickel-base alloys has been determined also. In some cases, for example U500, 5 the effect on mechanical properties has been found. However, little systematic work has been done to clarify the action of each of the important alloying elements in controlling the phases formed in complex commercial alloys and their behavior. The effect of molybdenum on the carbides formed in M252 was investigated by Beattie and verSnyder.6 Application of the results provided by that work

Jan 1, 1963

By E. Miller, J. M. Eldridge, K. L. Komarek

Activities of magnesium in liquid Mg-Sn alloys have been determined between 5 and 90 at. pct Sn and 990" and 1290°K by an improved isopiestic method wherein tin specimens, heated in a temperature gradient and contained in crucibles of special geometry, were equilibrated with magnesium vapor in a closed titanium system. The crucibles were designed so that the equilibrium compositions of the specimens were satisfactorily preserved on termination of the experimental runs by quenching. The activity values are in excellent agreement with those predicated on the phase diagram and allowed a delineation of the solidus curve of the compound Mg2Sn near its melting point. EQUATIONS have been recently derived relating the chemical potentials of the components to the liquidus and enthalpy data for binary systems exhibiting one congruently melting compound.&apos; The liquidus curve of the Mg-Sn system between the eutectics was carefully redetermined and the thermodynamic properties thus calculated were in reasonably good agreement with values derived from electromotive-force measurements of an,&apos; but differed greatly from the iso-piestically determined values of Ashtakala and Pid-geon.3 The present study was initiated: a) to resolve the discrepancies; b) to develop a method for measuring activities in systems having volatile (and possibly highly reactive) components; and c) to use the method in a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVb systems, i.e., Mg-Pb, Mg-Sn, Mg-Ge, and Mg-Si. This paper describes the results for the Mg-Sn system. An isopiestic technique, originally developed by Herasymenko 4 and adapted for alloys having a component of high reactivity and low volatility,5-8 was modified in this study by using crucibles designed to preserve the equilibrium composition of highly volatile liquid specimens on quenching from high temperatures. Tin specimens, contained in tightly covered graphite crucibles and heated in a temperature gradient, were equilibrated with magnesium vapor of fixed pressure from a magnesium reservoir kept at constant temperature in a previously evacuated and sealed titanium tube. During equilibration magne-

Jan 1, 1967

By Alvin H. Lense

In the spring of 1967, after a careful study of existing geology along the Pacific Coast including Alaska, the USBM, in conjunction with the USGS, decided that the offshore area around Nome, Alaska, presented an unparalleled land-to-sea comparison site for the evaluation of marine core drilling techniques and sampling equipment. Considering the geological evidence available and the production history of the Nome Beaches (5-6 million oz. of gold recovered), it appeared likely that gold in commercial quantities could occur in the offshore area. A 180 sq mi area of Norton Sound, extending roughly 14 miles to the east and west of Nome and averaging 6 miles to the south, was tested by approximately 530 line-miles of sub-bottom profiling. A total of 4043 ft (56 holes) were drilled in unconsolidated sediments, yielding mixtures of gravel, sand, silt and clay. Of the total holes drilled, 16 went to bedrock and six were terminated short of their intended depths due to boulders which halted penetration, or rough seas which caused the ship to move as the anchors slipped over hard sea-floor surface. The rest of the holes were terminated when the penetrative capabilities of the drills were reached, or when the required amount of geological data were attained.

Jan 8, 1968

By William Blauvelt

Tun technical and engineering problems in the manufacture of coke are today the problems of the byproduct oven. Except in a few special localities, practically no beehive ovens have been built in the United States for the last 5 or 6 years except as renewals of old plants, and during these years the total number of beehive ovens in existence has been steadily falling. On the other hand, the number of byproduct ovens has increased from 4624 in 1911 to a total of about 7660 in operation at the end of 1917; with 2800 building, this makes a total of about 10,460 which will be in operation in 1918, or shortly thereafter. Preliminary Government estimates place the total production of coke for 1917 at 56,600,000 tons, the largest tonnage in the history of the industry. Of this 34,000,000 tons or 60 per cent. was beehive, and 22,-600,000 tons, or 40 per cent. was byproduct coke. Some time in 1918 the production of byproduct coke should pass the beehive output, and when the byproduct ovens now building are completed the total byproduct capacity will be about 40,000,000 tons of coke per. annum, which is over 70 per cent. of the record-breaking total coke production of 1917. The reasons for these changes in the coking industry are familiar to all of us, and need not be discussed here.

Jan 3, 1918

By T. R. Young, S. A. Scott

9.5-1. Introduction. The use of pipelines to transport solids has been successfully accomplished with many different materials. One of the oldest applications is the dredging and placing of hydraulic fill. Many installations have been made and operated for long periods of time with excellent dependability, low operating cost, and low maintenance. It is not the aim of this chapter to give the engineer the answers from which to design a pipeline, but rather to supply helpful information from which to start the project. There are several phases of solids pipelining which as yet have not lent themselves to quick engineering answers. Investigations have been carried on by many, with several theories advanced by the various investigators. In recent years certain notable theoretical advances in hydraulic transportation have been achieved. Vertical transport, using balanced "leg" operation, now appears competitive with other forms of vertical transportation. In addition, horizontal transport utilizing capsules has been proven experimentally to be attractive because of lower pressure drop than the conventional methods of solid transport in fluid media. With the aid of the computer, the laborious calculations associated with pumping calculations have been greatly simplified; and with this tool the pipeline engineers of the future will undoubtedly be able to develop a more comprehensive understanding of solids-fluid transport. 9.5-2. Theory. There have been many excellent studies made and information is available in the literature, but a general comprehensive theory of pipeline transportation of solids has not been advanced. The existing flow theories will give approximations for minimum and optimum flow velocities, friction head losses, energy requirements, and pump and pipe size The principles of dynamic similarity and scaling laws are well understood for the flow of pure liquids. There are no firm methods of scaling slurry pipelines of small diameter to larger diameters except for a few empirical.

Jan 1, 1968

By C. Stansfield Hitchen

The paper describes the application of the logarithmic wedge sector method of quantitative spectrography to the estimation of commonly occurring minor impurities in crude and refined tin. Both arc and spark methods of emission were employed and with the former a new device was used to overcome difficulties arising from the low melting point of the metal. The impurities investigated included antimony, arsenic, bismuth, copper, iron, lead, and zinc, their concentrations lying, in general, between 0.01 and 0.50 per cent. The results obtained show that the method may be usefully employed for the estimation of bismuth, copper, iron, lead, and zinc, in amounts ranging from 0.50 per cent to well below 0.01 per cent. Arsenic and antimony, however, could not be estimated in amounts less than 0.03 and 0.07 per cent respectively. Out of a total of 116 estimations by arc and spark emission, in 96 the errors were less than 5 per cent of the total quantity of the element present, whereas in the remaining twenty, the errors lay between 5 and 25 per cent. Spectro-analytical data for the several impurities studied are given in the form of tables, and curves correlating line-intensity with concentration have also been included. DISCUSSION (R. G. Waltenberg presiding) D. M. Smith, London, England (written discussion).—I am interested in Dr Hitchen&apos;s account of his investigations on the application of spectrographic methods to the assay of tin and congratulate him on his valuable contribution to the literature on the subject of quantitative spectrum analysis. Some of the results obtained in the course of investigations carried out for the British Non-Ferrous Metals Research Assn., although obtained under somewhat different experimental conditions, may be of interest in connection with this paper. Arc and spark spectra of standard samples of tin containing various known amounts of antimony, bismuth, cadmium, copper, lead, silver and arsenic have been investi-

Jan 1, 1933

By J. A. Jr. Church

I. EARLY FURNACES. . COPPER blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18, ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,&apos; and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon&apos;s data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950

By Arthur Boynton

IN THE preparation of this paper the writer has been influenced by the fact that descriptions of various means of cleaning blast-furnace gas have been published and that further descriptive treatment of the subject will probably be less interesting than a statement of conclusions with regard to preferable methods which have been reached by him as a result, of experience and observation in this country and also as a result of somewhat detailed investigation of the subject made toward the end of the year 1927 on the Continent of Europe and particularly in. Germany. Owing to various circumstances, including a cost of fuel that is extremely high in relation to the wages of labor, the German iron and steel industry has accumulated experience in gas washing which is as yet in part lacking in the United States of America. The paper begins with a statement regarding the economics of the use of blast-furnace gas, then considers the principle&apos;s and practices employed in its purification. USES OF BLAST-FURNACE GAS For many reasons having to do with the utilization of coke-oven and blast-furnace gases in steel manufacture and with the use of hot metal, the blast furnace is now usually a part of a steel-producing unit, which also includes coke plant and rolling mill. Therefore both blast-furnace and coke-oven gas are usually applicable to any of the iron and steel-making processes, including the generation of power, and their allocation in any given works should be considered as a single problem. The uses to which blast-furnace gas, either alone or mixed with coke-oven gas may be put, include the following: Regenerative Heating of Air for the Blast Furnace.-This is the oldest and metallurgically the most important of all uses. It is universally performed with unmixed blast-furnace gas and under proper conditions should require not over 23.5 per cent. of the total gas generated for a blast temperature of 1350° F. For Steam-raising Purposes.-This is almost universally done with unmixed blast-furnace gas. From the standpoint of quantity used, it is at the present time the most important application in American steel-works practice.

Jan 1, 1928

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn&apos; observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,&apos; Houska and Averbach,&apos; and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.&apos; cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.&apos; Finally, the possibility of stress-induced order at dislocations, schoeck locking,&apos; must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-&apos; mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

By I. W. Wark

AN attempt has been made to compare the influences of the two most widely used depressants-alkalis and sodium cyanide-and the most widely used activator-copper sulfate-on the air-mineral contact induced by five sulfur-bearing compounds: (1) sodium di-ethyl dithio-phosphate (sodium Aerofloat); (2) potassium ethyl xanthate; (3) sodium di-ethyl dithiocarbamate; (4) potassium iso-amyl xanthate; (5) potassium di-n-amyl dithiocarbamate. Three different organic types are included in this group and for two of these types a higher and a lower homologue have been tested. The study of potassium ethyl xanthate, the preliminary results of which have been described,1 was continued until there had been obtained a comprehensive account of the influence of variations in pH value and in the concentrations of xanthate, sodium cyanide and copper sulfate on the adsorption of this xanthate by galena, sphalerite, pyrite and chalcopyrite. With concentrations of copper sulfate and collector that the work with ethyl xanthate indicated would give the most illuminating results, the other four collectors were tested in a less exhaustive way. The same general principles determine the influence of alkalis, cyanide and copper sulfate, no matter to which type the collector belongs, but there is a gradation in the quantitative measure of such influence. In the list above, the five collectors are cited in the order of their capacity to withstand the depressants, sodium Aerofloat being the least resistant, potassium di-n-amyl dithiocarbamate the most resistant. This order coincides substantially with that of the solubilities of the heavy metal salts formed by double decomposition with the collectors, those formed from sodium Aerofloat being most soluble. There is little difference between the third and fourth members of the series, and under certain conditions their positions are reversed.

Jan 1, 1934