Search Documents

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,' and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956

By K. H. Coats

This paper presents the development and solution of a mathematical model for aquifer water movement about bottom-water-drive reservoirs. Pressure gradients in the vertical direction due to router flow are taken into account. A vertical permeability equal to a fraction of the horizontal permeability is also included in the model. The solution is given in the form of a dimensionless pressure-drop quantity tabulated as a function of dimensionless time. This quantity can be used in given equations to compute reservoir pressure from a known water-influx rate, to predict water-influx rate (or cumulative amount) from a reservoir-pressure schedule or to predict gas reservoir pressure and pore-volume performance from a given gas-in-place schedule. The model is applied in example problems to gas-storage reservoirs, and the difference between reservoir performances predicted by the thick sand model of this paper and the horizontal, radial-flow model is shown to be appreciable. INTRODUCTION The calculation of aquifer water movement into or out of oil and gas reservoirs situated on aquifers is important in pressure maintenance studies, material-balance and well-flooding calculations. In gas storage operations, a knowledge of the water movemenr is especially important in predicting pressure and pore-volume behavior. Throughout this paper the term "pore volume" denotes volume occupied by the reservoir fluid, while the term "flow model" refers to the idealized or mathematical representation of water flow in the reservoir-aquifer system. The prediction of water movement requires selection of a flow model for the reservoir-aquifer system. A physically reasonable flow model treated in detail to date is the radial-flow model considered by van Everdingen and Hurst.1 In many cases the reservoir is situated on top of the aquifer with a continuous horizontal interface between reservoir fluid and aquifer water and with a significant depth of aquifer underlying the reservoir. In these cases, bottom-water drive will occur, and a three-dimensional model accounting for the pressure gradient and water flow in the vertical direction should be employed. This paper treats such a model in detail — from the description of the model through formulation of the governing partial differential equation to solution of the equation and preparation of tables giving dimensionless pressure drop as a function of dimensionless time. The model rigorously accounts for the practical case of a vertical permeability equal to some fraction of the horizontal permeability. The pressure-drop values can be used in given equations to predict reservoir pressure from a known water-influx rate or to predict water-influx rate (or cumulative amount) when the reservoir pressure is known. The inclusion of gravity in this analysis is actually trivial since gravity has virtually no efFect on the flow of a homogeneous, slightly compressible fluid in a fixed-boundary system subject to the boundary conditions imposed in this study. Thus, if the acceleration of gravity is set equal to zero in the following equations, the final result is unchanged. The pressure distribution is altered by inclusion of gravity in the analysis, but only by the time-constant hydrostatic head. The equations developed are applied in an example case study to predict the pressure and pore-volume behavior of a gas storage reservoir. The prediction of reservoir performance based on the bottom-water-drive model is shown to differ significantly from that based on van Everdingen and Hurst's horizontal-flow model. DESCRIPTION OF FLOW MODEL The edge-water-drive flow model treated by van Everdingen and Hurst1 is shown in Fig. la. The aquifer thickness b is small in relation to reservoir radius rb. water invades or recedes from the field at the latter's edges, and only horizontal radial flow is considered as shown in Fig. 1b. The bottom-water-drive reservoir-aquifer system treated herein is sketched in Fig. 2a and 2b. Here the aquifer

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By J. C. Scully, G. Sanderson

The electrolytic formation of y hydride in thin foils of Ti-5Al-Z.5Sn alloy and four Ti-A1 binary alloys has been studied by electron microscopy and electron diffraction. Two orientation relationships have been found: THE adsorption of hydrogen by titanium alloys from aqueous solutions has been widely reported. This can occur, for example, in both alkaline' and acidic2 pickling baths, in chemical polishing374 and electro-polishing Solutions,3,4 during cathodic polarization5" and under certain corrosion conditions,7,8 Etching reagents may also produce visible precipitates, sometimes after an aging period.9 During an investigation into the stress corrosion susceptibility of a titanium alloys by thin foil electron microscopy many observations have been made of hydride precipitation which has been deliberately promoted by techniques that are described below. The characteristics of hydride precipitation are reported and the observed crystallographic orientation relationships are discussed with reference to distortion in the titanium lattice created by the presence of the hydride. EXPERIMENTAL TECHNIQUE One grade of commercial titanium and five alloys were examined. Their composition and hardness values are shown in Table I. All the materials were in the form of thin sheet, 0.05 to 0.065 cm thick, which had been annealed after cold rolling. Foils suitable for transmission electron microscopy were made in two ways: a) by chemical polishing; and b) by elec-tropolishing. The solution used for chemical polishing was a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. During this polishing specimens were manually moved up and down in the solution. The reaction was veFy rapid, specimens thinning to foil thickness (2000A) in 5 min. Since chemical polishing solutions tend not to cause hydride contamination if they are kept cool3 no attempt was made to prevent the solution from becoming hot during the thinning operation. Electropolishing was performed at -30° C with a mixture3 composed of 295 cu cm methyl alcohol, 175 cu cm n-butyl alcohol, and 30 cu cm perchloric acid with an applied voltage of 40 v after chemically thinning specimens to approximately 0.017 cm thickness in a cool solution of 44 pct HF, 40 vol H2O2, and water in the volumetric ratio 1:6:3. EXPERIMENTAL RESULTS 1) Ti-5A1-2.5Sn Alloy. The Ti-5A1-2.5Sn alloy was severely contaminated by hydrogen during the chemical polishing. Foils obtained in this way contained large amounts of the y hydride phase. A typical micrograph is shown in Fig. l. The laths were identified as the hydride phase by selected-area diffraction of a large number of foils examined in a tilting stage that could be turned through 40 deg. Using the lattice spac-ings of the alloy obtained by X-ray diffraction as a standard the a value of the hydride was determined fromo the electron diffraction patterns to be 4.38 to 4.40A. The accuracy of this figure is only about ±2 pct. Further evidence of the identification was obtained by vacuum annealing chemically polished foils of the alloy at 500°C. This resulted in the dissociation of the hydride with the production of dislocations and possibly vacancy loops as shown in Fig. 2. The hydride

Jan 1, 1968

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By Henry Rawdon

THE structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i.e., manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the inclosures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in "pure" metals in general (etching pits).

Jan 9, 1917

By T. A. Lang

For permanent structure underground, where rock is not competent, support usually consists of concrete or reinforced concrete. However, temporary supports in the form of timber or steel are often needed during construc-tion. Although the history of rock bolting is relatively short—50 years— their use has become widespread in general engineering construction as well as mining. This profusely illustrated and detailed study covers a broad range in the field of rock belting: from the behavior of rock and bolts including rock properties, masses, and structure; mathematical formulae for rock bolt applications; through analysis of various operations and descriptions of the bolts themselves. Rock construction is one of the oldest of the engineering arts and its origin is lost in antiquity. From the days when early man decided that he wanted to improve the natural caves which he was using for shelter and protection or made a river crossing by placing rocks to form a ford or causeway, we have had structures made of rock. It is not too much to say that rock in situ as a structural material forms part of every major engineering undertaking. Rock bolting is one means whereby the inherently good characteristics of rock in situ are preserved and used to the best advantage and the bad characteristics ameliorated. In many cases the latter are accentuated by construction processes used. Rock bolting, as with other rock construction techniques, is only just beginning to emerge from being an art. Consequently, its theory and practice is still more descriptive than mathematical. ROCK BOLTING In underground excavations, where the rock is not competent, support is provided. For the permanent structure, this generally consists of concrete or reinforced concrete. However, support may be needed during construction before the concrete can be placed, and conventionally this consists of timber or steel support in the form of ribs, struts, and lagging. Alternatively, rock bolts may be used. Although their use dates back over 50 years, it is only in recent years that rock bolts have become widely used, not only in mining but in general engineering construction. A rock bolt is a steel bar which is inserted in a hole drilled in rock. The end away from the rock face has a device which permits it to be firmly an- chored in the hole and the projecting end is fitted with a plate which bears against the rock surface. The bolt is placed in tension between the anchor and the plate, thereby exerting a compressive force on the rock. The essential feature of a rock bolt is that it is placed in tension. This distinguishes it from anchor bars which are grouted into holes in rock, but which are not prestressed. The difference between an anchor bar and a rock bolt when the rock bolt is grouted in is analogous to the difference between the reinforcement in ordinary reinforced concrete and in prestressed reinforced concrete. The view that rock bolts only pin or nail blocks or slabs of rock which are loose to the sounder rock behind them is erroneous. Rock bolts are useful for this purpose and have been so used for a long time. However, the term rock bolting, as used here, means the designed use of rock bolts to reinforce and develop the rock around an excavation into a structural entity which can competently play its part in a structure such as a powerhouse or a mine installation. Rock bolts behave quite differently than steel ribs. They can be installed at the working face directly after blasting and within a short space of time can be exerting a stabilizing pressure on the loosened rock surface. This early installation not only partially restores loosened blocks of rock to their original unloosened positions, but also it prevents the gradual relaxation or loosening of the decompression zone behind the new rock face. In contrast, steel ribs generally use timber blocks, wedges, and lagging between the ribs and the irregular rock surface. The timber is relatively compressible, and loosened blocks of rock must move outwards an appreciable distance before any load builds up on the steel ribs. Also, the ribs may settle as the foot blocks and foundation become compressed. Hence, it may take several days or weeks before the rock has moved sufficiently to make the steel ribs carry an effective load.

Jan 1, 1961

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By G. W. Preckshot, J. W. Gorman

MOLTEN metals offer an excellent medium for the study of molecular diffusion and interphase transfer. In the absence of intermetallic compound formation, solutions of molten metals are solutions of elements. Therefore, complicating factors such as molecular structure, dissociation, association, polarization, and so on, are generally absent. Further, metals remain in the liquid state over a wide range of temperature. Thus, the effect of temperature on transport processes can be studied in more detail. Although some data are available for the diffusion of metals in the molten state at high temperatures,"""".'!' the most useful and accurate data are those for the diffusion of various elements in mercury at room temperature. The effective radius of diffusion for the various elements in mercury may be calculated from the Stokes-Einstein relation.'-These calculated radii are compared with the atomic and ionic radii calculated from X-ray data on crystals." The effective radii of diffusion of the alkali and alkali-earth metals correspond to those of the neutral atom; those of cadmium, silver, lead, zinc, thallium, bismuth, and tin correspond to ionic radii; and those of copper and gold indicate larger radii due to association with mercury or more likely, faulty diffusion data. Independent evidence"' supports the notion that alkali metals are uncharged in amalgams. The concept of metals moving free of their conductance electrons in the liquid state has been discussed by Eyring, et al,'" in connection with studies on the viscosity of pure molten metals. Considering the approximate nature of the tabulated atomic and ionic radii and the variance in the diffusion measurements, the application of the Stokes-Einstein equation to the diffusion of metals in mercury gives gratifying results. It is noted that a number of these metals have article radii eaual to or less than those of the solvent mercury.".'*,"' Soba1,'" sing the inaccurate Roberts-Austin20 data, indicated that the effective radius of diffusion might well be a function of temperature. Additionally in studies of mass transfer between phases, many conflicting opinions have been expressed concerning the assumption of equilibrium at the interface." ,","," The results of the present work on the diffusion of solid copper in molten lead throws light on the tempera- ture variation of the diffusion radius as well as the extent of the interfacial resistance. The theoretical background and experimental procedure are presented here in detail. Results on other systems will be presented in subsequent papers. Nomenclature The following nomenclature is used in the paper: A—cross-sectional area of diffusion column, sq cm C, C,—concentration of solution and saturated solution respectively, g per cc D,D'—-diffusivity, sq cm per sec e—Naperian base h—ratio, k/D k—mass-transfer coefficient, cm per sec L—diffusion column length, cm n—series index q—flux, g per sq cm-sec r—radius, cm or A R—-gas constant t—time, sec T—temperature, K V—volume, cc w—weight of copper-lead alloy on copper cylinder WT—-total copper transferred to lead diffusion, column, g Z—distance from top of diffusion column, cm 2'—distance from copper-lead interface, cm (2' = L-2) u,,—roots of diffusion equation Mathematical Apparatus The model shown in Fig. 1 applies to the diffusion of solid copper into molten lead. Here Fick's first law may be written where all terms are defined in the nomenclature. It is assumed that the volume of the lead column is constant. This is justified since experimental densities compared favorably with calculated densities based on perfect interstitial mixing. Thus there is no counter diffusion of lead. It is clear that 2 in Equation [I] should be measured relative to the interface which moves relative to the diffusion cell but not to the liquid phase. Hence, the frame of reference is the plane of the copper-lead interface. The diffusivity calculated at constant volume, D", is that defined by Hartly and Crank" and is designated herein as D. No Interfacial Resistance—The two situations of the presence and absence of interfacial resistance will be treated. The simplest is the latter which re-

Jan 1, 1959

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,' dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix. Few of the operating companies in the Florida phosphate district have applied isopachous (Greek isos, equal and pachys, thick) to mapping. The writer believes there is a need for the techniques discussed herein and that they can be applied to mapping other geologically similar areas in either economic or scientific investigations. The land-pebble phosphate district of Florida occupies a compact area in the west-central part of the state. It includes mainly the following land survey divisions: Ts. 27 S. through 32 S. and Rs. 20 E. through 26 E. The town of Mulberry, Fla., is in the approximate center of the district. The strata of the area, which is part of the Gulf Coastal Plain, occur in thin formations with broad outcrop belts, and low dips. The topography is subdued and gently rolling with three marine terraces, which are found at 30, 100, and 150 ft above sea level,' accounting for most of the relief. Occasional small sinkhole lakes are present, most of them above the 150-ft shoreline. The phosphate deposits occur in unconsolidated sediments such as clays, sands, and sandy clays. They are overlain by a heterogeneous assemblage of sands, clays, muck, and iron-cemented sand, easily penetrated, in most cases, by a hand auger or drill. Limestone, locally called bedrock, or a calcareous bedclay, thought to be a residue of the limestone, directly underlies the phosphate deposits. General Requirements Most companies and independent prospectors operating in the district have furnished prospecting data to the U. S. Geological Survey. The information is recorded on either field logs or prospecting maps and includes the following information for each hole drilled: location of the hole, thickness of the overburden, thickness of the matrix, phosphate content in long tons per acre, grade of the phosphate content expressed as the percentage of bone phosphate of lime (P2O5 x 2.18) or BPL, and the per- centages of iron-aluminum oxides and insolubles. The phosphate is classified according to size as either pebble or flotation material. The milling processes of the companies vary, and the size classification is necessarily different in many cases. However, pebble may be considered as larger than 14 mesh and flotation material as smaller than 14, but larger than 150 mesh. Some prospecting data include the exact depth at which bedrock or bedclay was reached, and these figures greatly increase the reliability of the data both for isopachous mapping and for mapping the basement. A drilling density of four holes per 40 acres of land furnishes a minimum amount of data for isopachous and related mapping. From the minimum of four, densities up to 32 holes per 40 acres are used. The various drilling densities may influence the choice of the proper scale. Selection of the proper scale is dependent upon the known drilling densities, the subsurface variations to be shown, the extent of the area to be mapped, and the detail desired in the completed map. Scales of 1:24,000, 1:4800, and 1:2400 are used in isopachous and related mapping by the Florida Phosphate Project. The 1:24,000 scale is used most effectively with drilling densities not exceeding eight holes per 40 acres. The subsurface variations should be relatively low and uniform, permitting the use of smaller intervals without undue crowding of the lines. Comparatively large areas can be mapped on this scale, but minute detail is necessarily sacrificed, because the information is drawn from a maximum drilling density of only eight holes per 40 acres. Isopachous and related maps of the 1:4800 scale are made of areas on which the drilling information covers from 4 to 16 holes per 40 acres. Moderate subsurface variations with relatively sharp gradations can be shown accurately. The area represented by the maps is reduced considerably in favor of detail. The 1:2400 scale is most frequently used by the Florida Phosphate Project. It lends itself particularly well to isopachous and related mapping, being easily adapted to the multiform drilling data available. Maps of this scale are prepared with information ranging from 4 to 32 holes per 40 acres; however, use of the minimum drilling density on the

Jan 1, 1952

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener's two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep'on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,' the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,' that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane') required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

By J. Richard Maier

Short-range mine planning (less than five years) previously was accomplished using contour and isopac maps, pencil and paper, an abacus, and our lucky quarter. Through the use of both micros and mainframe time sharing, Glenrock Coal Company (GCC) has been able to virtually put the old equipment away (except the problem solving quarter). In the process, GCC has saved many man-days and eliminated the more tedious parts of mine planning, such as picking elevations off a map with an engineer's scale and repetitive calculations. These savings have allowed GCC to do a more extensive job of mine planning as well as offer more alternatives, making GCC better prepared for possible economic changes. Mine planning, simply, involves looking at what has been done and deciding what needs to be done using various constraints. The application of this concept is not as easy as it sounds. The need for experience and insight cannot be replaced by a machine, but machines can supplement a person's ability by doing the bookkeeping and the repetitive work. Through the application of computers and their accessories, GCC has brought mine planning to a more modernized state. The following paper will detail the development and use of one system as used at GCC. Please note: In the figures and tables following, some of the data has been altered to protect confidential information used in mine planning.

Jan 1, 1983

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

THE book covers principally the assaying of silver and gold and the determination of these values in ores, sweepings, and base metal. It seems to have been written more for the goldsmith and jeweler than for the primary producer of metals. There were approximately sixty different substances needed in the operations described and not over a dozen different types of raw material (ore, matte, crude or alloyed metal) are mentioned. The methods of separation used were essentially simple and reasonably reliable, though the processes were not sufficiently understood to permit the selection of the simplest effective ingredients, and there was a great tendency to employ complicated fluxes, with unnecessary repetition of long-continued heatings indicative of a leisurely pace of life. Practically all the processes described are based on a few chemical facts: the inability of gold to combine with sulphur, while silver and the base metals form easily fusible sulphides; the ready oxidation of base metals; and the ii- solubility of gold in nitric acid. Fluxes serve to make earthy impurities fusible, and to carry oxidizing or sulphurizing ingredients. Many of the processes of assaying had changed little up to the beginning of the present century. Even as late as 1924, when the writer took a University course in fire assaying, the crucibles, cupels, scorifiers, molds, and tongs were identical with those of the sixteenth century, though the wind furnace had a stack on it and the muffle for cupelling was gas-fired.* The fluxes were purer, but of the same essential composition. That this branch- or twig-of metallurgy had not advanced in any funda-

Jan 1, 1949

By Daryl R. Tweeton, Jerry R. Riding, Grant Buma, Frank J. Rosswog

In situ solution mining of uranium has environmental advantages over conventional mining. The leaching of uranium, however, alters the ground-water quality in the aquifer where the mining occurs. Currently, regulations require that the ground water be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring ground-water quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By R. J. Marcotte, C. T. Eddy, R. J. Smith

THE objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. CAST STEELS The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition-all of which is summarized in Table I. [ ] PROCEDURE The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By G. S. Ansell

RCENTLY, in investigating the high-temperature creep properties of an aluminum, SAP-type alloy, MD 2100, fabricated by Professor F. V. Lenel of Rensselaer Polytechnic Institute, Ansell and Weertman1 found unusually low creep rates. These creep rates are 4 or 5 orders of magnitude lower than is predicted by the slowest creep mechanism based upon dispersion-hardened alloy theory. They ascribed these results to a lack of both normal active dislocation sources and a continuous three-dimensional dislocation network. If one couples these results with the following factors of production and microstructure: 1) The compacted and sintered aluminum powder compact is hot-extruded, with an extrusion ratio of 25:1.2 2) The alyminum oxide particles are approximately 140A units thick, and have a spacing varying from 0.05 to 1.5 1. 3 3) The alloy has plate-shaped grains with minor axes of about 5 X 10 -3 mm and major axes several orders of magnitude greater than this.'

Jan 1, 1960