Search Documents

By J. L. Thompson

There are two basic forms of the LPG-slug process: the gas driven and the water driven. The pressure required for miscibility between gas and LPG prohibits the use of the gas-driven LPG process in shallow reservoirs. The water-driven LPG slug process normally exhibits good sweep efficiency. However, displacement of the LPG by water is poor. An improvement in this process appears possible by injecting a slug of carbon dioxide between the LPG slug and the water drive. Laboratory experiments were conducted in homogeneous linear systems to determine the effect of pressure on the various displacement zones. In the carbon dioxide-LPG displacement zone, the effect of pressure on the displacement efficiency is negligible above the miscibility pressure. However, the displacement efficiency decreases linearly with decreasing pressure below the miscibility pressure. With water displacing carbon dioxide, it was found that the recovery of carbon dioxide after water breakthrough can be predicted from its solubility in water. A displacement test was conducted with LPG and carbon dioxide slugs large enough to avoid interference between the oil-LPG, LPG - carbon dioxide and carbon dioxide - water displacement zones. Under these conditions, essentially complete oil and LPG recovery was obtained. However, a substantial amount of carbon dioxide was left in the core at water breakthrough. INTRODUCTION It has been shown in homogeneous linear systems that essentially complete oil recovery can be obtained by displacement with a miscible fluid such as LPG. Economic considerations dictate that the valuable LPG also be recovered. Methods proposed for recovering the LPG include (1) displacement with natural gas at a pressure high enough to make the two fluids miscible1 (the disadvantage of this method is that the required pressure of about 1,500 psi is too high for shallow reservoirs) and (2) displacement of the LPG with water2 (principal disadvantage is that a large amount of LPG remains in the formation because of poor displacement efficiency). This paper treats an improvement in the water-driven LPG slug process3,4 where carbon dioxide is injected between the LPG and water. Carbon dioxide is completely or at least partially miscible with propane and soluble in water; thus, displacement efficiency is improved at both ends of the carbon dioxide slug. To minimize effects of other variables, all experiments were conducted in linear core systems. GENERAL PROCESS DESCRIPTION The displacements of propane by carbon dioxide and carbon dioxide by water are considered separately, assuming enough of each is injected to prevent mutual interference. Displacement descriptions are confined only to the part of the pore volume containing mobile fluids unless otherwise specified. The schematic representation is given in Fig. 1. Starting at the producing well, a zone containing only oil is followed by a zone containing a single-phase mixture of propane and oil. The concentration of propane increases in the direction of the injection well and ultimately grades to pure propane. Then follows a zone containing a mixture of propane and carbon dioxide in continuously varying proportions until 100 percent carbon dioxide is reached. In this zone, the concentration of carbon dioxide in the immobile water phase also varies from zero to full saturation. Whether the displacement of propane by carbon dioxide is of complete or partial miscibility depends on pressure and temperature (Fig. 2). If the horizontal line representing the prevailing pressure intercepts the boundary curves of the phase envelopes for the prevailing temperature (i.e., if the pressure is lower than the critical

By K. K. Kershner, W. A. Calhoun, C. W. Funk

Future resources of aluminum may require the utilization of low grade ores to provide a more permanent protection for the nation. Aluminum minerals such as cloy, shale, and high iron laterites may become important sources. An evaluation of reserves is given. New laboratory results are reported on the Vereinigte desilication process. THIS report on future resources of aluminum metal emphasizes the necessity for investigating utilization of low grade potential ores to provide more permanent protection for the nation. Partial or complete interruption of the importation of high grade aluminum ores must be given consideration. Ultimately, aluminum minerals such as clay, shale, and high iron laterites may become the principal sources of aluminum. The development of extractive processes for treating these low grade materials is a step in long-range national preparedness that should receive more attention. In formulating such processes, the application of beneficiation methods for the purpose of classifying the several types of minerals before subjecting each type to the more expensive extractive procedures should be considered, and a careful survey of the basic factors of power sources, transportation facilities, and sources of raw material should be made. Domestic Bauxite Resources Of the domestic supply of current, treatable-grade bauxite, 95 pct comes from Arkansas. The present reserve of Arkansas bauxite suitable for metal production, including abrasive-grade, Bayer-grade, and modified Bayer-grade ores, is 34,000,000 tons. The total reserve of bauxite of all grades is approximately 75,000,000 tons. Reserves are estimated on a mined and dried basis. Data available to the Bureau of Mines in 1948 to 1949 were used in preparing Table I, which shows a breakdown by grades of bauxite for about a half of the reserves of the state. The modified Bayer ore, 10,555,500 long dry tons, is based on a cutoff of 8 to 15 pct silica. The sub- marginal 10,074,700 long dry tons is assumed to contain more than 40 pct gibbsite, more than 15 pct silica, and less than 32 pct available alumina. A considerable amount of this low grade material was consumed in 1949 and 1950. Additional tonnages of bauxitic and kaolinitic clays are indicated by the Bureau of Mines drilling project.' Applying a 50 pct factor to arrive at long tons mined and dried, the results of this project are approximately 31,500,000 tons kaolinitic clay at +35 pct Al²O3 and 11,800,000 tons kaolinitic clay at 20 to 35 pct A1,0,. Total reserves of kaolinitic clays are probably quite extensive—several times the reserves shown in the Bureau's work. Total reserves of bauxitic and high iron clays from the drilling program and previously established figures are 63,980,000 tons. The mineral dressing methods,' the lime-sinter process, he lime-sinter modification of the Pederson process," the lime-soda sinter process,"-' and the Alcoa combination processa. have been described in the literature and will not be elaborated upon here. The less familiar Vereinigte Aluminium-Werke process used by the Germans during World War 11 may require some amplification. It was used to bene-ficiate boehmite ores containing 12 to 18 pct silica for a feed to the European Bayer process. Ore was

Jan 1, 1952

By A. P. Young, F. C. Holden

IN many of the early investigations of the aging of titanium alloys, it was observed that the retained beta phase could be aged to a high hardness without an apparent change in microstructure; moreover, in some alloys it was found that even a very rapid quench produced beta having an anomalously high hardness. What appeared to be hard beta phase was designated as "beta prime," to distinguish it from the softer normal retained beta phase. Frost and co-workers'.' demonstrated that the increased hardness is caused by the formation of a metastable phase, omega, which can be identified from its X-ray diffraction pattern. This reaction also has been studied by Brotzen, et a1.,3 and the structure of the omega phase has been published by Silcock, et al.," and by Austin and Doig.3 The X-ray diffraction analysis by Austin and Doig indicated that omega is low in alloy content, approaching the composition of the stable alpha. The aging process proceeds by the path Thus, overaging results in the formation of alpha and the ultimate disappearance of omega. This is accompanied by a decrease in hardness and a recovery of ductility. The present work represents a study of the aging process in a high-purity Ti-6.4 Mn alloy, in which optical and electron microscopy, X-ray diffraction, and hardness data were correlated. The specimens, 1/8-in. sections cut from 1/4-in.-diam rod, were heated in argon to a temperature just into the beta field (810°C), held for 1 hr, and water-quenched. The aging samples were heated in air for 1 hr at 300 to 500°C. The specimens were ground and mechanically polished, finishing with alternate etching and polishing on a slow-speed wheel to remove disturbed metal from the surface. The surface finally was swab-etched, rinsed with tap water, and air-dried. The etchant used was an aqueous solution containing 1 1/2 pct HF and 3 1/2 pct HNO3. This procedure is identical with that used for preparing metallographic specimens, except that the optimum degree of final etching required for electron microscopy may vary from that used for light microscopy. Metal replicas, backed with silica, were prepared from plastic strip-pings for examination with the electron microscope. Complete details of the procedures used for preparing these replicas are available elsewhere." Fig. 1 shows a comparison between the structures revealed by the electron microscope and those obtained by conventional light microscopy. Hardness and X-ray diffraction data are listed in Table I. No evidence of a second phase is apparent in the optical micrographs for the as-quenched sample, or for the specimens aged at 300 or 400°C; fine alpha particles can be seen in the specimen aged at 500°C. In the electron micrographs, visible equiaxed pocks appear in the as-quenched specimen, and, with increasing density, in the samples aged at 300 and 400°C. After aging at 500°C, the structure becomes markedly coarser and develops an oriented appearance of a second phase, coincident with the appearance of visible alpha particles in the light micrographs. These observations are confirmed by X-ray diffraction and hardness data. In these specimens, aged for 1 hr, the intensity of the omega pattern increases to a maximum at the 400°C aging temperature, corresponding to maximum hardness and the maximum density of pocks in the electron micrographs. At this point the beta phase shows a definite enrichment in Mn. At 500°C, little or no omega re-

Jan 1, 1959

By R. HAYDEN, H. B. HALLOWELL, H. O. Hofman

THE object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe in his classical paper "Contributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks.2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker' and Addicks.4 The absorption of gases has received' attention by Hampe,5 Stahl 6 and Heyn.7 The effects of casting-temperature have been noted by Stahl.8

Mar 1, 1907

By John G. McLain

OF all the zinc that the world consumed in 1936-'38 the United States took about 31 per cent, and almost 14 per cent of the world's zinc supply in that period was used for galvanizing purposes in the United States. Further examination of the statistics shows that about 71/2 per cent (147,500 tons in 1939) of the world zinc consumption goes into the galvanizing of sheets in the United States, which is what I am going to talk about in this paper. There is nothing especially new about galvanizing; in every year since 1921 somewhere between 41 and 49 per cent of the country's zinc consumption has been used for this purpose, and yet few people not specialists in its manufacture know much about how it is made. You take an iron or steel sheet and dip it in molten zinc and there you have a galvanized sheet-that about epitomizes popular knowledge of the subject even among engineers.

Jan 1, 1941

By C. Allen Born

INTRODUCTION As the title of this paper suggests, the author does not believe that risk can be managed. Rather, the objective is to identify the risk which will be present in a given venture and assess the level of that risk which is acceptable. More often than not, the risk which is present is subject to little or no modification. After identifying and measuring the risk a corporation will decide to accept it and proceed in such a way that it will be less exposed, or it will decide not to proceed at all. The exercise for a corporation is different only in degree from everyday judgements made by average people in average situations. However, that word "degree" means that it is considerably more complex on the corporate level. There is good reason for the additional complexity of corporate risk evaluation. The variables influencing a company's decision can be more numerous and the penalties for miscalculation much greater than those normally encountered by an individual. It should be understood that no analysis of risk, certainly not one as brief as the following, can do more than touch on some of the high points. Before examining the sorts of risk which affect the development and operation of specific mines, let us consider the broader aspect of the term with which mining companies, and all other business corporations, must deal. Companies must determine their long-term objectives and strategies within the context of a constantly changing world. To plot their direction they must attempt to read the future by seeking answers to questions such as: How will society evolve? Which businesses will thrive? In which of these should we place our emphasis? If a company hopes to be around five or ten years from now it must make the attempt to answer such questions in order to judge the impact of changing patterns in the evolving business environment. Information is available to allow the lessons of the past to be projected on the future. We have data on birth rates, economic booms and busts, patterns of conflict within and between nations, drought and other forces of nature as well as individual events which cannot be predicted, but which over time, do seem to occur in regular cycles. Ultimately the question "where will we be and what will we be doing a decade from now?" must be answered by one or more senior people with responsibility for the company's future. The compilation and interpretation of hard data by competent support staff, can only be used up to a certain point in determining future corporate strategy since there will be alternative possible futures and a high degree of risk will always remain. At this point those elusive qualities of experience, instinct, and - "gut feeling" - become important factors in choosing a long-term corporate direction. The goals of a company have a significant bearing on its attitude towards risk. This in turn dictates the "hurdle rate of return on investment" which a project decision-maker will require. The hurdle rate is the minimum-discount-percentage-rate applied to forecast cash flows to give a present value of zero to the All-Equity-Funded Investor. The feasibility study for a project is a fundamental tool in the management of risk. An experienced team has an established and well-understood set of ground rules for the preparation and assembly of a feasibility study. The necessary degree of conservation is built in at all levels of study data and, if the project is technically feasible, the hurdle rate becomes a catch-all measure of risk in a base-case project cash flow.

Jan 1, 1985

By William F. Boericke

THE Christy Creek clay mine of the General Refractories Co., in the Olive Hill District, ranks with the most important producers in the north-eastern Kentucky fire clay field, both from production of high-grade flint clay, as well as unusual extent and thickness of deposit. The property is but one of a number controlled by the General Refractories Co. in this district, but is given first consideration among them by the operating staff. Its total area is over 5000 acres, owned in fee or by lease of clay mining rights, and although mining operations have been in progress for over five years, scarcely one per cent of the ground has been worked as yet. The mine is near the southwestern end of the clay field, which extends in a belt 12 miles wide and 55 miles long, in a southwestern direction from Kenova, W. Va., which, as the name indicates, is at the junction of Kentucky, Ohio, and West Virginia. Olive Hill, where there is one of the l1Ulin plants of the General Refractories Co., and to which the clay from the mine is shipped, is about 26 miles distant from the mine. Connection is made with the Chesapeake & Ohio R. R. by a spur line . 8 miles in length, owned and operated by the company.

Jan 1, 1929

TULSA SECTION At the smoker concluding the two day meeting of the Tulsa section of the American Institute of Mining and Metallurgical Engineers, Tulsa, Okla., Feb. 26, 1919, Dr. Willis T. Lee, the new head of the Geological Department of the University of Oklahoma, was introduced to the assembled geologists and mining engineers. Dr. Lee requested that the geologists and engineers who were making a specialty of petroleum geology assist him in giving a good course in practical oil geology in the Geological Department of the University. After a motion offering the services of all present in giving lectures on their special subjects had been adopted, Dr. Perrine of Hutchinson, Kans., named the geologists who were pledged to give lectures in Dr. Lee's course. The students in geology at Norman are assured of the latest information regarding practical work in petroleum geology and will have the inspiration derived from contact with men who are actually at work upon the problems which they are studying. Dr. Lee and President Brooks of the University are to be congratulated upon the introduction of this .method of instruction. The plan thus put into operation is similar to the graduate system of coaching in athletics followed at many of the large universities; what is good for instruction in athletics should also prove good for instruction in applied geology.

Jan 6, 1919

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

By R. L. Perrine

This paper presents results obtained by consider ation of unstable miscible displacement within a porous medium as a quasi-turbulent displacement process, that is, a process characterized by fluctuations around a simpler, mean flow behavior. The instability usually results from the miscible displacing fluid having a viscosity lower than that of the displaced fluid. Such instability is evidenced in suitable experiments by the presence of viscous fingering. A unified theoretical relationship applicable to both stable and unstable displacement is derived. Parameters in the theory are obtained by empirical means. Although the theory describes an idealized conceptual model, agreement with experiment is quite reasonable up to moderately adverse viscosity ratios, such as 17:1. INTRODUCTION Many experimental studies of miscible displacement in porous media have been conducted with prediction of reservoir displacement efficiency as the ultimate objective. Most such studies have utilized lower displacing than displaced fluid viscosity, scaled to potential reservoir fluid pairs. Theoretical approaches have been largely limited to unit viscosity ratios, however, in spite of the necessity for an understanding of the mechanism of the unstable, adverse viscosity ratio displacement process. An obvious reason is the difficulty of describing in mathematical form the viscous fingering characteristic of these conditions. Observation of experiments conducted with dyed fluids in transparent systems suggests an analogy between unstable miscible displacement and turbulent flow in a pipe. In both cases there are fluctuations around a simpler, mean flow behavior. An important difference is that flow behavior of interest in the porous medium is entirely transient, contained within a transition zone between displacing and displaced fluids. Transient behavior complicates description in that coefficients in the equations become variables rather than constants. In the study reported here, the analogy with turbulent flow has been used in treating unstable miscible displacement as a quasi-turbulent displacement process. The purpose has been to derive, even if restricted to an idealized conceptual model, a unified theoretical relationship applicable to both stable and unstable displacement. A relationship meeting these specifications up to moderately adverse viscosity ratios, such as 17:1, is presented. One fluctuation parameter in the theory and dispersion coefficients are obtained by empirical means. The idealized theory is compared with experimental results. UNSTABLE MISCIBLE DISPLACEMENT AS QUASI-TURBULENT DARCY FLOW The miscible displacement of one fluid by another within a porous medium is considered in this study. Flow conditions are such that Darcy's law is applicable. It is further assumed that, by the stability criterion proposed by perrine,1 initial flow conditions lie well within the regime of instability. Thus substantial viscous fingering is assured. We wish to show how this flow regime can be represented as quasi-turbulent. That is, the Reynolds number for the established flow conditions is below that for inertial or turbulent flow within a porous medium, and lies within the regime for which Darcy's law is valid. Yet flow behavior can be described as the combination of some relatively simple average result, and characteristic fluctuations that are superimposed on the simpler behavior. Stated another way, flow behavior includes the movement of layers of fluids with different velocities past or over one another. Such descriptions are characteristic of turbulent pipe flow. The fluctuations in the present case are a direct consequence of the local viscous fingering which accompanies the unstable displacement process. Should displacement become stable, fluctuations would die out. It is of particular importance to note that fluctuations such as these can interact in a way that contributes to material transport by the basic flow. The basic transport equations required for engineering calculations must be modified to reflect this fact.

Jan 1, 1951

By R. L. Orr, O. D. Sherby, J. E. Dorn

Creep data for pure metals at temperatures above those at which rapid recovery occurs (above about 0.45 the melting temperature) are correlatable by means of the equations and These correlations were applied successfully to data for aluminum, iron, nickel, copper, zinc, platinum, gold, and lead as well as for simple alloys. For a given metal, AH is a constant about equal to the activation energy for self-diffusion. THE early recognition that creep is stimulated by thermal activation prompted numerous investigators', ' to apply the same laws that are valid for the viscous behavior of liquids to analyses of creep data. To a good first approximation these laws are summarized by the equation were i is the creep rate; T, the absolute temperature; R, the gas constant in cal per degree per mol; T, the applied stress; AH, the activation energy in cal per mol; S', a constant dependent on the entropy of activation, the frequency of activation, and the contribution of each activation to the strain; and B', a constant dependent upon the size of the flow unit that is activated. Although Eq. 1 describes the flow of viscous fluids very accurately, its application to the creep of solids has been disappointing. Two reasons for the failure of Eq. 1 for creep are now known: First, the decelerating creep rates during primary creep demand that the internal structures of the metals are changing and that these changes might be reflected by changes in one or more of the three creep parameters S', AH, and B'. Consequently when the conventional methods of evaluating these parameters are employed by comparing the secondary creep rates at a series of temperatures and at a series of stresses, the true effects of temperature and stress are masked because of simultaneous changes in one or more of the creep parameters. Second, as will be illustrated more fully later, three distinctly different types of investigations have shown that the stress term for high temperature creep enters the analysis as and not as t/T. This rather unexpected result points sharply to a significant fundamental difference between the mechanisms for the viscous behavior of fluids and the high temperature creep of metals. More recent extensive investigations",'4 on the creep of high purity aluminum and several of its dilute a solid solutions have shown that where E is the total creep strain; temperature compensated time = for a constant temperature test; t, is the initial stress in a constant load test or the constant true stress in a constant stress test;" and t is the duration of test. • Eq. 2 is valid for either constant stress or constant load tests; but the total creep curve is difierent (i.e. the function, f, is differentl for each test. The fundamental origin of the validity of Eq. 2 is thought to arise from some equivalence of substructures in constant load creep tests at equal values of 0 or E. Both X-ray and metallographic examination revealed that practically identical lattice distortions and subgrain sizes are obtained for the same creep strain under the same load over wide ranges of test temperature.' Furthermore the room temperature tensile properties following equal creep strains at different temperatures under constant loads were also identical, illustrating that identical substructures were indeed obtained.' " A second type of correlation was obtained by differentiating Eq. 2 with respect to time, giving For the secondary creep rate, denoted by i,, But Eq. 2 reveals that 0, is a function of a, alone because the secondary creep rate in a given constant load test is always reached at a fixed value E,". Therefore where is the function that was introduced a number of years ago by Zener and Hollomon." Eq. 4 is not only valid for creep but will permit correlations between constant load creep and tensile data where e, is the rate of tensile straining and (TC is the engineering ultimate tensile strength.

Jan 1, 1955

By Verne C. Fryklund, S. Warren Hobbs

The Coeur d'Alene district in the panhandle of Idaho is one of the major lead-zinc-silver producing areas in the world. The value of recorded production to date has exceeded $2 billion. Country rock comprises six formations of the fine-grained, highly siliceous, and slightly metamorphosed Precambrian Belt Series. Small stocks of monzonitic rocks and several varieties of dikes intrude the sediments. The district is at the intersection of a north trending major anticlinal uplift and the west northwest-trending Lewis and Clark line of which the Osburn fault is the dominant feature. The district structure is complicated and comprises folds, some of which are overturned, and a complex of faults of diverse ages and directions of movement. Late Cretaceous stocks but are also probably Cretaceous in age. The productive veins are localized within a series of 12 subparallel, straight mineral belts that trend approximately N65°W and that appear to be controlled by deep fractures in the basement rocks. The mineral belts are in two groups, separated by 15 miles of post-mineralization movement on the Osburn fault. Veins and ore shoots are variously disposed within each mineral belt. Many crop out at the surface, but others apex several thousand feet beneath it. Local controls that influence the position of ore shoots within the mineral belts include the brittle character of host rock attitude of bedding relative to the mineralized fracture, and the amount and direction of movement on faults. Depth appears to have had little effect on the occurrence or type of ore. Ore occurs in a series of steeply dipping replacement veins of relatively simple mineralogy. Six periods of mineralization, ranging from Precambrian to Tertiary in age, are recognized. The productive galena sphalerite-bearing and tetrahedrite-bearing veins-of the main period of mineralization-are younger than the

Jan 1, 1968

Jan 1, 1951

By CHARLERS R. FETTEE

A slight decrease in drilling activity occurred in the oil fields of western Pennsylvania during 1945 and a considerable decrease in the shallow-gas territory (Upper Devonian or higher). The number of deep tests (Middle Devonian or deeper) completed was two less than in 1944 and these did not open any new reserves of natural gas. Thus far, no commercial oil has been encountered in sands below the Upper Devonian in Pennsylvania. Oil production declined 8 per cent.

Jan 1, 1946

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By Charles Janin

(San Francisco Meeting, October, 1911.) THE first successful bucket-elevator dredge to operate in California was put in commission at Oroville in March, 1898. There had been numerous previous attempts at dredging, but none of the earlier boats proved a success. The gold-miners in California early conceived the idea of a machine to dig gravel from the beds and bars of auriferous streams that were inaccessible by the methods then employed, and it was only a few months after the discovery of gold in California that such a machine was. shipped around Cape Horn from New York to San Francisco. This was, however, but the forerunner of many failures in gold-dredging, and was soon at the bottom of the Sacramento river. During succeeding years many other unsuccessful attempts were made, and it was not until 1897 that a dredge of the single-lift bucket-elevator type was floated on the Yuba river. This dredge was built by the Risdon Iron Works for R. H. Postlethwaite, and would probably have been a success if it had been operated on some of the rich Oroville ground instead of in a turbulent stream, where the dredge was wrecked during a flood, and was not repaired. Fig. 1 is a sketch-map of California, showing gold-dredging areas. It is not my intention to narrate in detail the history of the early failures in gold-dredging, and the various steps in the development of the modern boat, but merely to touch upon this in a general way, and to call attention to the wide difference in capacity and operating-cost between the first successful dredge, with an actual capacity of 600 cu. yd. per day-though its rated capacity was in excess of this-and the present modern dredge with 15-cu. ft. buckets, and an average capacity of 250,000 cu. .yd. per month. Even this enormous capacity has several times been exceeded on monthly runs. The first successful dredges

Mar 1, 1912

By F. C. NINNIS

AT THE Belmont mill, the pregnant solution is de¬livered to a 30 by 10-ft. tank, from which it is pumped to three Merrill clarifying presses of the sluice-bar type, whence it flows through the meter to the precipitation supply tank. ?The solution for precipitation is pumped by a 10 by 10-in. Aldrich triplex pump and delivered through a 6-in. line to the forty-eight triangular frame Merrill presses at the head of the mill. Zinc dust is fed in at the pump suction and the solution precipitated to 0.01 to 0.02 oz. silver. The solution flowing from the presses is tested at 1-hr. intervals with sodium sulfide. All solution is precipitated to the same value; 4J tons of solution are precipitated for each ton of ore treated and the presses are cleaned every 15 days. The product from the presses' is dumped into steel cars having steam-jacketed bottoms, in which they are dried until the moisture content is between 15 and 17 per cent. when 8. per cent. of soda and .3 per cent. of borax are added and the contents thoroughly mixed. In the case of special clean-ups, the precipitate is tested and the flux is added to meet the requirements.

Jan 1, 1921

By C. G. Albert

The clay particles of 2 microns or less required for modern paper coating are predominantly flat plates, lying smoothly on the sheet and producing a high gloss. Operating speeds of today's coating machines necessitate a clay composition of 60 and sometimes 70 pct solids as against the 35 to 40 pct required in the past. Since clays in suspension may solidify in flow, only those of intrinsically low viscosity can be used as high coating solids. THE literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing. The paper industry itself is not the ultimate consumer. For the greater portion of the clay the end product is the printed page, and the demands of printing and publishing have sparked some of the technological advances in paper making which have, in turn, brought about methods employed in the kaolin industry. As compared with the product of 20 or 25 years ago, one of the most striking characteristics of the graphic arts today is the mass production of quality printing of fine pictorial work, much of it in full color. During this time periodicals with printing standards close to those of yesterday's slick-paper publications that were printed on a slow schedule and for a limited circulation have grown to the point where they go out to many millions of readers, often at weekly intervals. The complexity of technological improvements brought about by this increased circulation is probably not appreciated even by technical people, unless they have had reasonably close contact with the industry. The advance has come about through developments not only in the art of printing, but also in the field of paper making and even at the level of clay mining and processing. The smoothness required for faithful reproduction of the kind of printed matter under consideration is attained with a clay-coated paper. Since the distribution expense of the publication will depend to a great extent on its weight, the paper used must not be too heavy. This means a lower basis weight than was normal for conventional clay-coated papers some 25 years ago. And for this mass production market it becomes necessary to provide a paper having these and all the other required characteristics at a very moderate price—not the premium price conventional clay-coated papers formerly demanded. This challenge has been met by a new method of producing coated paper. In the past, application of clay coating to paper was a conversion operation, performed separately from the making of the base sheet. The newer development is called machine coating. Here application of the coating is an integral step in a continuous process by which wood pulp, clay, and other ingredients are manufactured into a sheet of coated paper. Many more problems are involved in this procedural change than are apparent at a casual glance. The coating operation, for example, must function at much higher linear speed than could be obtained with coating mechanisms previously employed. The application machinery developed to meet this requirement necessitated changes in composition of the coating color.* This created new requirements, summarized below, for the clay employed as coating pigment. In addition to smoothness, a relatively glossy printing surface is needed, and to a large measure it is the function of the coating clay to make possible the development of both these surface characteristics. Traditionally, pigments such as satin-white, prepared by reacting lime with paper-makers' alum, were used to assist in producing a high finish. However, economic considerations and others preclude large-scale use of such material in the new processes. In the 1930's Maloney' discovered that a certain particle size fraction of kaolin, consisting

Jan 1, 1956