Search Documents

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By E. H. Crabtree

This paper traces the experimental and pilot plant work completed by the authors since 1939 including the various methods which have been developed in applying coarse activated carbon to cyanidation. The methods and results developed by the authors in desorbing gold and silver from carbons are given and the possibilities for the re-use of the desorbed carbons are discussed

Jan 1, 1950

By Henry H. Thomas

In Tasmania a tailrace tunnel to handle water discharged from a turbine generator has been successfully driven by a machine tunneling method similar to that described in the July 1962 issue of Civil Engineering. The Hydro-Electric Commission, Tasmania, is constructing a high- head (2750 ft) power project that will utilize the storage in the Great Lake (1,150,000 acre-ft) at an elevation of 3380 ft. The underground power station will house six vertical shaft turbo-generators, each rated at 50,000 kw. The tailrace tunnel, 16 ft diam and 14,600 ft long, was driven through a reasonably homogeneous hard mudstone. It was decided to excavate this mechanically in the hope of saving some money on excavation and a considerable sum on the ultimate lining of the tunnel. Mechanical engineers from Tasmania worked with the firm of James S. Robbins and Associates of Seattle, Wash., which designed and supplied the "mole."

Jan 4, 1963

By F. R. Van Horn

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer's standpoint and that practically no consideration is given to the employee's point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must be secured, but they do not agree as to how this can best be done.

Jan 4, 1917

This is a brief account of the history of unit operation in the Salt Creek field, Wyoming, from the time of the agreement to prorate production in March, 1921, to the present. An attempt has been made to evaluate the savings in development and production costs resulting from the unit plans adopted. Summarized, these savings have amounted to $11,650,000. No effort has been made to estimate any increase in ultimate recovery, for it is believed that unit operation can be justified on saving in development and production costs alone. It would require nearly 20,000,000 barrels of additional oil to be produced in order to return the amount saved by not drilling unnecessary wells. Four horizons are affected by unit or near-unit programs, as follows: The principal operator is under contract with six companies to operate 10,400 acres. This includes all of the productive area of the First Wall

Jan 1, 1930

EUGENE WESLEY SHAW,* Washington, D. C. (written discussion ?).-Studies of the probable future production of oil wells and fields-particularly those in the nature of the recent work by Lewis and Beal, having the object of increasing the percentage of recovery-rank, in both practical and theoretic value, very high, if indeed they do not outrank all other petroleum investigations except structural surveys. Even such surveys, although saving untold millions that might have been spent in prospecting unpromising territory, may have less ultimate value than generally supposed, for it may perhaps be argued that much if not most of the condemned territory will sooner or later be tested-some is already productive-and the most that can be rightly claimed is the recovery of cream first; also that the consumption of the richest portions first cannot be extenuated, as it might with some resources, on the ground that if the best is not taken now it will deteriorate.

Jan 5, 1918

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose molding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat-, abrasion-, corrosion-and oxidation-resistant and high-strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, chemical process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present conditions, the US and North America, with the possible exception of Cuba, have no commercial ore reserves. There are chromite deposits, as will be described, but they would be used only under highly abnormal conditions if all outside sources were cut off for an extended period. All chromite used in the US is imported from the eastern hemisphere in which are contained the principal world reserves. The main suppliers in 1980 were the Republic of South Africa (43%), the USSR (21% ), the Philippines (12%), Albania (11 %), Turkey (8%), and others (5%). The strategic nature of chromite is obvious. End Uses-Grades and Specifications As noted before, the three principal uses for chromite are metallurgical, refractories, and chemical with a fourth minor use as foundry molding sand. For metallurgical applications chrome ore is first reduced in electric carbon arc furnaces to various types of ferrochromium alloys. There are high, medium, and low carbon ferrochromiums with carbon ranging from 0.01 up to 10%. Chromium itself ranges from 50 to 73 %. Ferrosilicon chromium and ferrochromium-silicon grades have chromium from 33 to 67% and silicon from 3 to about 48%. Since iron is reduced with chromium, the Cr:Fe ratio of the ore will determine the ultimate grade of the ferrochromium whereas carbon and silicon can be controlled during processing. MgO, A12O3, CaO, and excess SiO2, are removed in slag. A small amount of pure chromium metal is prepared by alumino-thermic and electrolytic processes from essentially iron-free chrome components that have been made via the chemical route. The higher grades of ferrochromium with chromium in the 66 to 73% range can only be made from ores with not only high chromium content, but low iron, i.e., high Cr:Fe ratio. These ores, conventionally termed metallurgical grade, have Cr2O3 contents of 45 to 56% with Cr: Fe ratios of 2.5 to 4.3. A standard composition is generally 48% Cr2O3 and 3:1 Cr:Fe ratio. Very high grade ores are often blended with lower grades even with the high iron chemical grade. For some ferrochromiums, additions of high alumina refractory grade are used as slag conditioners to facilitate smelting while still contributing chromium values. A lower grade ferrochromium, the high carbon charge chrome, has become the predominant grade in use today for making chromium-bearing steel alloys. This

Jan 1, 1983

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The initiation of localized cracking in hydrogenated high strength steel was dependent on the developmeni of a critical hydrogen conceniration and relatively insensitive to the magnitude of the applied stress. The stress was believed to influence the deluyed failure process by providing the means for grouping the hydrogen. On the basis of an assumed distribution law the observed changes in the lower critical stress as a function of notch acuity, yield strength, and temperature were predictable over a significant range of these variables. THE phenomenological characteristics of delayed failure in high-strength steel have been comprehensively investigated and the behavior has been attributed to the strong embrittling action of hydrogen.1-3 Delayed failure or, as it is also termed, static fatigue, is the most sensitive means of detecting hydrogen embrittlement since it allows the maximum time for hydrogen diffusion during a test.3 The nature of delayed failure cail be aptly described by four parameters which are schematically depicted in Fig. 1. The upper critical stress corresponds to the rupture stress in a conventional notch tensile test. The lower critical stress or static fatigue limit is the stress below which no delayed failure will occur. The incubation period is the time required for the formation of the first crack and the fourth parameter is the failure time. An increase in hydrogen content, notch acuity, or strength level of the material increases the susceptibility for delayed failure by decreasing the lower critical stress, the incubation period, and the time to failure.lY3 A decrease in test temperature prolongs the incubation period in accordance with the lower diffusion rate of hydrogen, and also de-

Jan 1, 1961

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By Harrison A. Schmitt

One of the great copper-producing areas of the world is comprised of five U. S. western states and northern Sonora, Mexico. The Southwest province of this area, covering southern Arizona, south- western New Mexico, and northern Sonora, produces some 55 pct of U. S. copper output and the equivalent of 15 pct of world production. In 1956 the area produced about 550,000 tons. Tucson is approximately the center of the oval- shaped province, which measures only 300 miles on its east-west axis and about 200 miles on its short axis. Northwest of the oval, and forming a tenuous connection with the Utah and Nevada copper fields, is an important operating mine, Bagdad, and also the now inactive United Verde. Along its north- south axis, running from Globe, through Tucson, to Nogales, ten moderate to major copper properties have been discovered or revived during the past 15 years, and five of these in only the past seven years. The latter five properties lie in an area 25 miles in diameter, centering 20 miles south of Tucson. In order of discovery, or revival, they are: Banner's Mineral Hill and Daisy; Cyprus et al's Pima; Duval's Esperanza; Asarco's East Pima (now called Mission mine) ; and Lewisohn's Peach. Total tonnage is estimated at about 250 million tons averaging some 0.90 pct Cu, but ultimate production may exceed this amount since some of the reserve is open ended.

Jan 6, 1959

By T. J. Hudson, P. B. Queneau, J. D. Prater

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolving during the oxidation. Data were recorded on metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The study was concluded by laboratory testing a flowsheet based on the foregoing observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1.6 lb of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained in the copper concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NOD; up to 3% N2O also was present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, HAS was evolved.

Jan 1, 1974

By H. E. Lee, P. C. Feddersen

Greenockite is the only known cadmium mineral of importance. It occurs rather universally, in minor concentrations, as a secondary mineral in sphalerite deposits. The world's cadmium output is obtained through the processing of metallurgical by-products, largely from the treatment of residues from electrolytic zinc, retort zinc and lithopone plants. These sources are supplemented by the processing of fumes from lead and copper smelting operations. The development of modern selective flotation practice in the decade 1920-1930, which permitted the economical mining of complex lead-zinc ores, resulted in significant increases in the quantities of cadmium entering lead smelting systems. Being closely related to zinc as to occurrence, properties and production, most detailed description of cadmium recovery methods are to be found recorded in connection with zinc metallurgy. Other than occasional articles pertaining to particular operational procedures, literature offers but little in the nature of a balanced survey of lead smelter cadmium recovery practices. While many of the basic operations described for the recovery of cadmium from zinc by-products are applicable to the treatment of lead plant products, the inherent problems involved differ widely. In general the cadmium content of related by-products from routine lead smelting operations is present in lower concentrations, exists in a less soluble state and is associated with both a greater quantity and a greater variety of detrimental impurities. To cope with these problems, lead smelter practices are found to follow the general outline: Preparatory Processing 1. Concentration operations 2. Sulphation operations Cadmium Plant Processing 1. Leaching operations 2. Purification operations 3. Sponge precipitation operations 4. Metal recovery operations 5. Refining and casting operations As in the case of related zinc plant operations, cadmium recovery practices at lead smelters are not standardized. They not only vary as to type, but also extent. Depending upon prevailing conditions, lead smelter cadmium operations range from simple concentration campaigns, for the purpose of sufficiently "up-grading" products for shipment elsewhere, to complete processing steps for the production of refined metal. Preparatory Processing The cadmium content of lead smelter receipts is low and, as a rule, proportionate to the zinc content; the usual range of cadmium contained being of the order of 0.01-0.05 pct. Were it not for the low boiling point of cadmium, such small concentrations would, no doubt, be lost in the large tonnages of slag, metal and other smelter end products. However, the ready volatility of cadmium and its compounds at prevailing lead smelting temperatures results in its concentration in fractional portions of fume collected. This collected fume comprises a circulating load within the smelter system. Thus, the cadmium content of blast furnace fume* increases with each successive circulation until an equilibrium value is reached when the sum of the cadmium losses, due to handling and in slag, waste gases and other end products, becomes equal to the intake as ore. With ore receipts averaging, say 0.03 pct cadmium, the concentration value obtainable, through fume circulation in a routine manner, approaches 10-12 pct. In such operations, cadmium concentrations in blast furnace fume of from 3-5 pct are readily .attainable. However, the concentration gain beyond this range, with each additional circulation, is progressively decreased as a result of mounting losses occurring through handling and in end products. Therefore, to avoid excessive cadmium loss and to enhance the ultimate concentration anttainable, it is customary practice to isolate blast furnace fume at some intermediate cadmium content for special concentration procedure. The most common type cadmium concentration "campaign" involves special smelting operations wherein a relatively high portion of blast furnace fume at 3—6 pct cadmium is incorporated into the sinter charge. This type practice is roughly illustrated by the diagram on p. 111. Cadmium fume collected from lead blast furnace operations is not amen-

Jan 1, 1950

By Wallace W. Wilson

This DaoerAA calls to attention for the first time, to the writer's knowledge, a purported recovery of oil by substantially horizontal gas cycling that is considerably in excess of 50 per cent of the oil originally in place. The average angle of dip along the path of travel of the gas is less than one degree of arc. The best recovery by gas cycling previously brought to the writer's attention1 occurred in the case of the Mile Six Field in Peru, where about 68 per cent of the original oil in place has so far been recovered. In this case, however. the recovery was greatly aided 1)y the high dip angle of about 17.5". An approximate estimate of recovery was made by the method developed by the writer' for the case of the Cook Ranch Field, using an average relative permeability ratio function dictated by past experience with a number of good quality sandstones. A result of about 40 per cent recovery of the original oil in place wa* obtained after the 8.5 pore volumes of cumulative gas cycling undergone by the Cook Ranch Field. Tile writer desires to emphasize what appears to him as the sound engineering practiced at Cook Ranch, and also the care attending the taking of data and the high quality of the calculations made. It is impossible to take issue on factual grounds with any of the conclusions drawn in the paper. It is, however, desired to point out the difficulty of explaining the unexpectedly favorable oil recovery on ordinary theoretical grounds. It would be of interest to know whether relative permeability ratios have been measured on the Cook sand. The operator is inclined to attribute some of the excess benefit to settling of the oil across the bedding planes into the lower part of the sand. It is difficult for the writer to appreciate the importance of such an effect, inasmuch as the concomitant opening of excessive vacated pore space in the upper part of the sand would he expected to cause excessive bypassing of the gas. REFERENCE 1. Welge. H. J.: "A Simplified Method for Computing Oil Recovery by (Gas or Water Drive." Trans. AIME, (1952), 195, 91. AUTHOR'S REPLY TO MR. WELGE Welge has poined out clearly the difficulty of applying material-balance procedures in calculating the Performance of low-pressure, dispersed gas injection operations. There can be no argument that even with the most favorable assumptions of K,/K,, and with cumulative gas cycling in excess of normal expectations, the calculated oil recovery will be considerably less than the 72.5 per cent recovery realized from this project to Jan. 1, 1951. There probably are at least two reasons for the unusually high recovery from this reservoir, the effects of which would be difficult or impossible to calculate by known methods: 1. The operator did not use the same injection wells for the entire operation, and exercised considerable control over producing GOR by changing the locations of injection wells whenever well performance indicated excessive bypassing. Fifty-six wells were used for injection, not over 29 of which were in use simultaneously. This procedure resulted in frequent shifting of the fluid movement patterns in the reservoir and undoubtedly increased the ultimate recovery. The writer knows of no satisfactory procedure for calculating the effect of this practice. 2. Vertical movement of oil across the bedding planes of the reservoir rock hy gravity drainage tended to maintain a relatively high oil saturation, and hence a favorable K,/K, ratio, in the lower sections of the reservoir. As pointed out by Welge, this condition has aggravated the tendency for high producing GOR, but at the same time it has resulted in increased oil recovery. As may be seen from the performance charts for the various battery areas, operating (GOR'S have been quite high for the last several years of reported history.

Jan 1, 1952

By A. S. Nowick, E. S. Machlin

One of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.' During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time requird for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error This method of showing stress-rupture data has been adopted by many investigators and the NACA.' By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, roo, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time lor rupture on stress, temperature, composition, and structure. In order to obtain this information, an investigation was made at the NACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given composition and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efliciency and power output of gas turbines used in aircraft propulsion can be increased. Theory The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 developed by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate-process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process." For example, in a chemical reaction the unit process is

Jan 1, 1948

By A. S. Nowick, E. S. Machlin

One of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.' During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time requird for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error This method of showing stress-rupture data has been adopted by many investigators and the NACA.' By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, roo, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time lor rupture on stress, temperature, composition, and structure. In order to obtain this information, an investigation was made at the NACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given composition and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efliciency and power output of gas turbines used in aircraft propulsion can be increased. Theory The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 developed by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate-process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process." For example, in a chemical reaction the unit process is

Jan 1, 1948

By Richard McCaffery

THE statistical analysis of blast-furnace data was undertaken to determine some of the relations which exist between the variables involved in furnace operation, and particularly to show the effect of variation of slag composition on such economically important factors as coke consumption, daily tonnage of pig iron and sulfur elimination. It was desired to correlate the results obtained in- commercial practice with those predicted from a study of the quaternary system lime-alumina-silica-magnesia. This paper presents the results of a preliminary study of blast-furnace daily operating reports, and is intended to indicate the suitability of our method of attack and something of the results that may be expected from an extended statistical examination of such data. It has been shown that blast-furnace slags are not composed of oxides, as reported by chemical analysis, but are actually composed of several compounds, each made up of two or more of the oxides present.1 These compounds persist in the liquid state, and the properties of a slag are the properties of a mixture of these compounds, and not of a mixture of the ultimate oxides .2,3 The oxides lime, alumina, silica and magnesia make up 94 to 96 per cent. of the usual blast-furnace slag, and assuming that we may neglect the remainder of the components, we may determine the minerals present, and their relative proportions, from a study of the quaternary system involving these four oxides. Operating reports from 15 furnaces were available for this investigation. Complete slag analyses for one slag per day were available, permitting the calculation of the mineral composition of the slags used. Basic, malleable and foundry irons, with silicon varying from 0.75 to 4.50 per cent. were included in the reports for this examination.

Jan 1, 1931

By John C. Shyne, Eric R. Morgan

WHEN temper rolled low carbon sheet is stored at room temperature before use, changes take place in its mechanical properties. This phenomenon is known as strain aging. Normally these changes are observed by means of Olsen ductility and Rockwell B hardness tests but' unfortunately such tests are relatively insensitive. Strain aging can be readily observed in the laboratory by means of tensile tests. The tensile test method is even more sensitive if the aging is allowed to take place in specimens which have been prestrained in tension rather than by cold rolling. In fact one of the great benefits of commercial temper rolling is that it introduces a residual stress pattern which tends to mask the effects of strain aging when the sheet is finally used in a pressing operation. Curves B, C, and D of Fig. 1 illustrate the changes that take place during the aging of commercial rimmed steel at room temperature following straining in tension, curve A, Fig. 1. The first important change that can be observed is an increase in the stress required to produce plastic flow. This increase is, in this paper, called the aging index. As aging proceeds and the aging index increases, there is also an observable return of the yield point, an increase in the ultimate tensile strength, and a decrease in elongation to fracture. The results of strain aging in deep drawing steel manifest themselves as stretcher strains (L?ders bands) buckling, 2nd tearing. In deep drawn parts such effects are undesirable and strain aging is a serious problem. The rate of strain aging of a steel depends upon its composition and prior mechanical and thermal history? but for most temper rolled ope

Jan 1, 1958

By AIME AIME

LOCAL COMMITTEES. GENERAL RECEPTION COMMITTEE.-Mr. and Mrs. H. S. Chamberlain, Mr. and Mrs. J. T. Lupton, Mr. and Mrs. T. H Lasley, Mr. and Mrs. R. S. Faxon, Mr. and Mrs. H. Clay Evans, Mr. and Mrs. C. E. James, Mr. and Mrs. B. F. Thomas, Air. and Mrs. H. S. Probasco, Mr. and Mrs. W. M. Lasley, Mr. and Mrs. L. W. Llewellyn, Mr. and Airs. T. G. Montague, Mr. and Mrs. E. B. Thomasson, Mr. and Mrs. C. F. Milburn, Mr. and Mrs. C. A. Raht, Mr. and Mrs. C. C. Notting¬ham, Mr. and Airs. Z. C. Patten, Mr. and Mrs. Willard Warner, Mr. and Mrs. S. R. Read, Mr. and Mrs. Carl White, Mr. and Mrs. M. M. Allison, Air. and Mrs. C. E. Buck, Mr. and Airs. H. F. Temple, Air. and Mrs. M. M. Hedges, Mr. and Airs. X. Wheeler, Mr. and Airs. John A. Patten, Air. and Airs. N. T. Montague, Mr. and Mrs. R. H. Williams, Mr. and Mrs. T. R. Preston, Mr. and Airs. Morrow Chamberlain, Mr. and Airs. T. C. Thompson, Mr. and Airs. T. L. Montague, Mr. and Mrs. O. L. Hurlbut, Air. and Mrs. C. A. Lyerly, Mr. and Mrs. Garnett Andrews, Air. and Mrs. M. B. Ochs, Mr. and Airs. Webster James, Mr. and Mrs. D. P. Montague, Mr. and Mrs. Z. C. Patten, Jr., Mr. and Mrs. W. A. Sadd, Mr. and Mrs. J. B. Pound, Air. and Mrs. George D. Lancaster, Air. and Airs. J. F. Johnston, Mr. and Mrs. R. W. Barr, Air. acrd Mrs. W. B. Davis, Mr. and Airs. Douglas Baxter, Air. and Mrs. W. R. Crabtree, Mr. and Mrs. Lewis M. Coleman, Mr. and Mrs. Newell Sanders, Mr. and Mrs. E. Y. Chapin, Mr. and Mrs. W: B. Riddell,. Mr. and Mrs. J. B. Frazier, Mr. and Mrs. John A. Moon, Mr. and Mrs. C. D. Mitchell, Dr. and Airs. J. H. Race, Mr. and Airs. A. W. Chambliss, Mr. and Mrs. J. P. Smartt, Mr. and Mrs. J. F. Tarwater, Mr. and Mrs. L. D. Drewry, Capt. and Mrs. A. B. Putnam, Mrs. Minnie C. Ewing, Mr. G. F. Meehan, Mr. Sam S. Gerstle, Mr. P. A. Brawner, Mr. C. M. Preston, Air. George M. Guild, Mr. L. M. Mansfield, Dr. J. W. Johnson, Dr. J. AI. Hogshead. EXECUTIVE COMMITTEE.-H. S. Chamberlain, Chairman; H. S. Probasco, C. M. Preston, H. Clay Evans, J. T. Lupton, M. B. Ochs, C. C. Nottingham, Al. Al. Alli¬son, R. S. Faxon, C. E. James, C. A. Raht. EXCURSION TO CHICKAMAUGA PARK.-T. C. Thompson, Chairman; B. F. Thomas, G. F. Meehan, Morrow Chamberlain, W. J. Bass, J. K. McGoodwin. EXCURSION TO HALES BAR LOCK AND DAM.-R. H. Williams, Chairman; John A. Patten, Newell Sanders, George M. Guild, Capt. A. B. Putnam. EXCURSION TO ROCK-WOOD.-F. H. Clymer, Chairman; T. L. Brown, T. A. Wright, J. P. Tarwater, T. L. Peterman. INSTITUTE HEADQUARTERS.-The Hotel Patten. THE first session, held Thursday evening, Oct. 1, in the Banquet Hall of the Hotel Patten, was called to order by Capt. H. S. Chamberlain, Chairman of the Local Committee, who, in behalf of the city of Chattanooga, extended a hearty welcome to the members and guests of the Institute.

Nov 1, 1908