Search Documents

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;'= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

By H. N. Eavenson

In a discussion in the Transactions of the Institute (vol. Xl, page 835 et seq.) the writer gave some data about the explosions of gas and dust in the coal mines of the United States, Canada, and Mexico…

Jan 1, 1915

By A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By H. O. HOPMAN

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. THE substance of this paper was prepared for the Seventh International Congress of Applied Chemistry, held in London, May, 1909, under the title, Some Developments in Blast-Roasting. In the absence of the author, a -short abstract of the paper was read, and the abstract only will appear in the proceedings of the congress. The present paper has been partly rewritten and considerably enlarged by information gained since the original was prepared ; also some illustrations have been added. Blast-roasting' is a generic term for the process of forcing air through finely-divided. metallic sulphide with the object of roasting and agglomerating in a single operation. At first the process was confined to a galena-concentrate ; lime, limestone, or gypsum was added, to serve both as a diluent to keep separate the particles of galena that they might be thoroughly oxidized, and as a flux that the partly-roasted ore might be agglomerated by the formation of some slag. Later it was extended to treat other metallic sulphides. The leading processes were the Huntington-Heberlein and the Savelsberg of Europe, and the Carmichael-Bradford of Australia. In the United States and Canada, the Huntington-Heberlein process has found application in some instances with galena-concentrates, for which it was originally intended; but this class of ore is not often treated alone, hence the process has had to be modified to suit conditions. The Savelsberg process has been transplanted to this country in about its original form. The Carmichael-Bradford is not used at present. The changes called for in the Huntington-Heberlein process to adapt it to the class of lead-bearing ores usually smelted have been the 1 A. S. Dwight, Engineering and Mining Journal, vol. lxxxv., No. 13, p. 649 (Mar. 28, 1908).

Jun 1, 1910

By Charles Will Wright

The application of the camera as an adjunct to topographic mapping began practically with its invention, and it has been employed with varying success since that time. With the exception of the camera to be described, the plate-camera has been universally used in this work, thus giving a projection of the area photographed on a flat surface. From such projections or photographs, by the rules of geometry and of perspective, points defining topographic features and seen from at least two camera-stations may be projected upon a ground-plane—the map.' In 1904 I employed the plate-camera for this purpose in Alaska, but found that the labor necessary to plot the maps, even in a general way, was long and tedious. In 1905 a small Eastman panoramic camera was fitted with spirit-levels, a sight-alidade and a transparent scale, introduced inside the camera to register the degree-points in the sky-line of the film-negative ; also, arrows to indicate the horizon-line. This was, on the whole, successful; but the details in the topography were not brought out in the views with sufficient clearness, aid the photographs were too small. These difficulties were overcome by obtaining a larger and more carefully constructed instrument, which was satisfactorily employed in the field during the year 1906. A panoramic view is made up of an integral number of perspective views upon flat surfaces, and logically is the most accurate and direct means to obtain an impression of a field of * Published by permission of the Director of the U. S. Geological Survey. Stanley, H. M. Photographic and Co-ordinate Surveying, Bans., xx., 740 to 766 (1891). Also, Flemer, J. ,4. Phototopographic Methods and Instruments, Report U. 8. Coast and Geodetic Survey, pt. 2, app. 10, pp. 619 to 735 (1897).

Jan 1, 1908

By H. O. Hofman

With the exception of the exhaustive paper on the Father de Smet mill, by its designer, Mr. A. J. Bowie, Jr. (Bans., x. 87), nothing, so far as the writer is aware, has as yet appeared on the stamp-mills of the Black Hills of Dakota, although they have been steady producers for the last ten years. Within the small area of about 6000 by 1600 feet, $2,271,341.14 was produced in 1887† from rock averaging $4 per ton in free gold. I. The Ores. Character of the Ores.—The gold of the district is found in quartz and pyrites finely distributed through vast bodies of mica- and amphibole-schists, argillites and phyllites, and also impregnating the schists themselves. The " Belt," embracing the section of Lead City, Terraville and Central City, is the only part worked at present. The principal associated mineral is iron pyrites, with some arsenopyrite and chalcopyrite, garnet and asbestos. The ores from open cuts and upper levels are more free-milling. than those from underground workings below water-line. Hence

Jan 1, 1889

F. E. BACHMAN, Buffalo, N. Y. (Communication to the Secretary) : The investigation so fully described by Mr. Laudig was undertaken with the idea of determining if it is possible to learn by expesiment, without an actual trial in the furnace, what economical results can be expected from the use of a given ore-mixture. The research was necessarily preliminary, and the results obtained are only to be depended upon so far as they relate to the samples treated. With the exception of the ores obtained from the stock-piles of the Buffalo Furnace Company, and several samples taken at a neighboring furnace, there is no certainty that the ores represented the average shipments of any mine. For this reason the publication of the names of the ores might do producers a great injustice. The names of the ores arc therefore withheld, and their identity is further .veiled by leaving out of the analyses the phosphorus-contents. The investigation was begun with the preconceived idea that the rate of reduction would be found to be dependent upon the accessibility of the particles of the ore to the action of the reducing-gas. In other words, a spongy, brown hematite or a very fine Mesabi would be the easiest reduced. I had formed a scale with No. 21 first, No. 30 second, No. 1 third, Nos. 5, 24, 25 and the remaining Mesabis fourth, etc , which is sufficient to show how much actual results differ from a judgment based on physical characteristics. The ore expected to be most easily reduced proved to be 25th in the list, while the one placed

Jan 1, 1897

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By Paul Tyler

STRATEGICALLY situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cial operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennesse's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1, 1938, was approximately 19,000,000 tons. Official estimates of reserves are overly conservative and evidence submitted before a joint Con-gressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1939

By Stanley Reichert

The manganese deposits of the Embree Iron Co., Embreeville, Tenn., are thought to be fairly typical and representative of the East Tennessee type of deposit, and so to warrent rather detailed description. The methods used by the Embree Iron Co. for prospecting and mining, and to a lesser extent for milling; should therefore be applicable to other East Tennessee manganese deposits, as yet' undeveloped. Early History and Discovery of Manganese Brown iron ore (limonite) was mined by the Embree Iron Co. at various times from 1890 to 1910. The early method was simply pick-and-shovel mining in open pits. Later hydraulic giants were used and sluice lines carried the ore down the mountain slopes to log washers.. During this phase of mining, manganese ore was discovered under the iron ore in some of the pits. In other areas oxidized zinc ore was found under the iron. It thus happened that the valuable zinc deposits were discovered in 1914. During the World War period, from 1914 to 1918, there was sporadic prospecting for manganese ore among the abandoned iron workings, but the main activity then centered around the recently discovered lead and zinc deposits. It was not until 1934 that manganese mining began in earnest, under the supervision of R. D. Pritchett, Mine Superintendent. Geology of the Manganese Deposits United States Geological Survey Folios 151 (Roan Mountain) and 118 (Greeneville show that Bumpass Cove is a synclinal structure thrust faulted along the southeast flank, but with normal sequence of strata along the northwest flank. Fig, l. shows the areal geology of Bumpass Cove as taken from the folios superposed on the U.S.G.S. -T.V.A. 1/24,000 topographic maps of the Erwin and Telford 7 ½ minute sheets. The manganese mines occur near the contact of the unfaulted Shady dolomite and the Erwin quartzite. This contact zone is deeply weathered, with overburden averaging 40 to 60 ft. thick. The material overlying' the bedrock along this normal contact is a very tough, plastic clay, termed "buckfat" or "ocher" by the miners. It is not a true ocher, however, in the sense of having commercial value. The manganese deposits occur along this "ocher" band. Fig. 1 also shows how the manganese deposits occur along the broad topographic terrace between the 2100 and 2200-ft. contour lines. This terrace lies at the foot the Erwin quartz ridge. Apparently it is the topographic is expression of the deeply weathered zone along the Shady-Erwin contact.

Jan 1, 1941

By E. C. Burke, W. R. Hibbard

Plastic deformation in magnesium single crystals was studied by tensile tests at room temperature utilizing an improved preparation and testing technique. Consistent critical resolved shear stress values for basal slip were obtained. The advent of pyramidal slip at room temperature was rationalized upon the basis of grip constraints. A bend-twinning hypothesis was advanced as an explanation of mechanical twinning which occurs as a complex stress-relief mechanism. INVESTIGATIONS of the plastic deformation of magnesium have been limited to the determination of the fundamental kinetics which may be summarized as follows: 1—Twinning on the {102).l 2— Slip on the (001) plane in the [loo] direction at room temperature.' 3—Slip on the {101) or {102) plane in the [loo] direction above 225°C." 4—Critical resolved shear stresses for basal slip in tension at room temperature of 83 g per sq mm with a variation from 57 to 127 g per sq mm." Bakarian' studied the compression of thin wafers of magnesium single crystals and classified the components of the deformation mechanisms as follows: 1—The Basal field: (001) at an angle of less than 20" to the compression surface. Fracture along {101} or slip on (001) followed by {101} fracture. 2—The prism field: (001) at an angle greater than 60" to the compression surface. Twinning on the {102) generally occurring during the early stages of loading, basal slip in the areas of original orientation and (001) slip within twins. 3—The central field: (001) at angles greater than 20" but less than 60" to the compression surface. Slip on the (001). 4—The critical resolved shearing stress for {101} slip above 225°C was 400 g per sq mm. Observations of mechanical twins in hexagonal close-packed metals have been summarized by numerous investigatorsb-' emphasizing a lateral or rotational atomic adjustment, in addition to the pure twinning shear, and the importance of reorienting the basal plane to a position more favorable for continued slip, rather than the resulting small dimensional changes. Criterion for the operative twinning planes has not been clearly established. Schmid and Boas hurmised that an energy condition related to the atom movements is the determining factor. MillerQ bserved that twinning stresses in zinc crystals decreased as the amount of prior deformation increased. Preparation of Specimens Magnesium single crystals % in. in diam x 8 in. long were grown from the melt under an argon atmosphere in a gradient furnace similar to that described by Jillson." Magnesium containing 0.018

Jan 1, 1953

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By Samuel Hoyt

THE writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + ß range, first described in 1913. These notes are offered, not at all as the final explanation of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520° C. and the other at about 600° C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600° C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600°. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + ß range and increased in magnitude with the amount of a up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + ß field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 12, 1918

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note. This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material In which the crystals here dealt with were grown was made from 1/8 -in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of travelling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection.

Jan 1, 1927

By Benjamin F. Merembeck

A mutispectral scanner (MSS) obtains remotely sensed data of the earth's surface in vector form, one vector element for each spectral sensing band of the MSS. Data generated by either airborne or orbiting MSS systems are organized in a lattice of scan lines and elements within scan lines. Each element, called a pixel, is represented by an observational vector and corresponds to a relatively small specific area on the ground. The total observations for a sensed scene frequently are in the millions and are composed of a number of populations, each representing a different land form category. Based on samples from the populations, the mean vectors, or spectral signatures, and the covariance matrices for the categories may be estimated. From these, an among category covariance matrix and a combined within category covariance matrix can be found. The total among category variance is the trace of the among category covariance matrix. Canonical analysis finds a linear transformation matrix such that the first transform variable accounts for the maximum possible part of the total among category variance. Similarly, the second transform variable, orthogonal to the first, accounts for the maximum possible part of the remainder of the total variance, and so on. Such transformation often results in over 95 percent of the total variance accounted for in the first three canonical variables, even though the initial number of spectral bands exceeded twenty. Transformation of bulk data into three canonical variates allows color map products to be developed by assigning each variable to a different basic color. Such color products are believed to be more useful for photo-interpretation than color products resulting from any combinations of three of the initial spectral bands.

Jan 1, 1977

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

Jan 1, 1915

By Alan Morris

Brass rod for use in automatic screw machines is one of the major products of the brass mills. A large tonnage is consumed each year in the manufacture of an endless variety of finished articles and parts for assembly into other products. The machines that do this work have been developed to a high degree of efficiency, and their manufacturers are still striving for higher production speeds. This development has brought with it a demand for brass rod to meet the increasingly difficult machining conditions. This paper is a report of the results of tests undertaken in an effort to obtain a measure of the effects of such variables as lead content, microstructure and cold work on the machinability of brass rod. It is realized that the term "machinability" has never been well defined. Power, finish and tool life all should have a place in such a definition. In practice it is sometimes found necessary to sacrifice some of these in order to obtain a rod that will not tend to throw up a burr, or will give a burr which is easily tumbled off. Again a specially stiff rod may be necessary because of long overhang from the chuck or a rod of special characteristics is needed to take a given broaching operation without chattering. It is only through an understanding of the effect of basic mill operations on the machinability of the rod that such problems as these may be solved most economically. It is hoped that this paper, together with the discussion it may evoke, will prove to be a basis for such an understanding. Testing Apparatus The testing apparatus used was of the single-tooth milling cutter type, in all respects sirnilar to that first used and described by Airey and Oxford1 and again by Boston. The machine used in the present test is shown in Fig. 1. It is an ordinary milling machine in which a heavy pendulum has been substituted for the pulley on the arbor. If the pendulum is raised

Jan 1, 1932