Search Documents

By Francis B. Foley

In examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found a piece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstattian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: Carbon Nickel Chromium Per Cent. Per Cent. PeR Cent. Metal from skin........................... 0.34 1.26 0.63 Widmannstattian zone.................... 0.21 1.18 0.63 Metal from center......................... 0.34 1.32 0.67 Such a condition might result from decarburization followed by recarburization of the skin. This section came from one of the branch runners to the bottom of the mold, not from the main runner, and it is difficult to conceive of decarburization occurring in this portion of a runner. If the metal were stripped while quite hot, some oxidation would take place but the recarburization is unaccounted for. It could not occur by segregation after solidification—the tendency then is for diffusion and homogeneity. The following seems to fit the conditions and is offered as an explanation. The outside layer of normal structure 0.065 in. (1.6 mm.) thick was chilled on the walls of the runner brick when the molten metal first entered the runner. As the molten metal flows by, the outside of the stream

Jan 1, 1920

By Walter McKee

WHEN mixed with common cast steel in quantities ranging from 11 to 13 ½ per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time. Manganese steel has been manufactured for about 26 years. .It was first made in a small way in England and subsequently produced in the United States in 1892. At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 lb. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13 ½ per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 5 ½ in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 5 ½ in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an

Jan 12, 1915

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By Paul Beck

WHILE the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room tem-perature is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains are not noticeably elongated in the first place. However, with small deformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell,1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is com-pleted-after the deformed grains have been replaced by new unde-formed grains-the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. elapsed before the deformed samples were ready for examination, and consequently no recrystallization time shorter than 5 min. could be measured.

Jan 1, 1939

By Alden Greninger

METALLURGISTS have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel.

Jan 1, 1940

By A. B. Kinzel

IT is with sincere appreciation and a deep sense of responsibility that I accept the honor of delivering the Howe Memorial Lecture. In our time metallurgical research has delved into phenomena ever more complex in character, so that much of this work must be done by organized teams. We, of the Union Carbide and Carbon Research Laboratories and the Electro Metallurgical Co., are truly a team and the lecture which is to follow is due largely to a few of the outstanding members of that team here cited and well known to you in their own right: John Lamont, whose work deserves special recognition, Walter Crafts, William Forgeng, William Binder, Robert Fowler, and David Swan. Thus it is a fitting pleasure to accept this honor for the research institution which I represent. Henry Marion Howe was truly inspirational and his breadth of view was such that he could use either the method of rigid proof or implied mechanism to further the broad understanding. But perhaps his outstanding characteristic was his sound judgment and his ability to weigh observations. The following is replete with observations and judgment as to their implication. We would like to feel that it is the type of dissertation which Howe, himself, would have enjoyed. Chromium carbides in stainless steel have, in a sense, been a key to the progress of the stainless steel industry. Brearley's first stainless steel, containing approximately 0.30 pct C, was successful because it differed from previous Fe-Cr alloys in that the carbides were present in such amount and form as to provide the stainless and cutting properties. Again, the 12 pct Cr die steels with a carbon content of 1.5 pct or more achieved their properties by virtue of the form and distribution of the chromium carbides. In the straight chromium steels with from 12 to 25 pct Cr, chromium carbide amount and distribution are once more the determinants with respect to physical properties and corrosion resistance. In each of the cases just cited the role of the carbide is in essence similar to that of iron carbide in carbon steel and this story is so well known that we need not dwell on it. In the austenitic stainless steels, the chromium carbide plays only a minor positive role with respect to mechanical properties, and for corrosion resistance the objective is to achieve maximum homogeneity. Thus the tendency has been to ever lower the carbon and correlatively the chromium carbide content of the austenitic steels. Today stainless steels with carbon less than 0.03 pct are beginning to find their true place, and this is being aided in major degree by our Company's introduction of a new type of ferrochromium having negligible carbon. The role of carbon in these austenitic steels has long been recognized, and a truly enormous amount of research has been devoted to the subject. Much has been learned about corrosion resistance, but the attack on the problem from the point of view of carbide precipitation and the nature thereof has left much to be understood. Because of its fundamental importance to the future of stainless steels, further study of the mechanism of carbide formation in austenitic steels is of interest. In the 18-8 Cr-Ni steels, which are typical of the austenitic class of steel, carbon is soluble in the aus-tenite to the extent of approximately 0.15 pct at 1832°F (1000°C). The solubility becomes less with decreasing temperature, so that at 1652°F (900°C) the solubility limit is approximately 0.06 pct, at 1472°F (800°C) it is about 0.03 pct, and at 932°F (500°C) it is approximately 0.01 pct. Obviously this is the ideal situation for the classical precipitation phenomenon. It is true that, in a sense, 18-8 austenite resulting from annealing is in a metastable state, and the phenomenon of ferritic precipitation from this austenite should be considered. However, in a so-called fully austenitic 18-8 steel this is secondary with respect to the carbides and can be neglected. A wide variety of chromium carbides is known. Only one chromium carbide, Cr,,C,,, frequently referred to as Cr,C, has been found in unmodified low carbon 18-8 steel. This, fortunately, simplifies the study of the precipitation phenomena. For this study an A.I.S.I. type 304 stainless steel of commercial quality was selected. Analysis showed C 0.07 pct, Mn 0.49 pct, Si 0.33 pct, Ni 9.34 pct, Cr 18.91 pct, and N 0.033 pct. As expected with this composition the steel was homogeneous after annealing except for a few pools of ferrite, which were disregarded in that their location was not coincident with subsequent carbide precipitation areas. On corrosion testing the steel was normal and typical of good commercial quality. Specimens 1/2xlx4 in. were annealed and subjected to precipitation heat treatment for 100 hr at 100" temperature intervals from 1000° to 1500°F and for ten selected intervals ranging from 5 min to 64 hr at 1300°F. These blocks were then cut into small pieces for metallographic studies. The first problem

Jan 1, 1953

This listing of members is arranged to show company affiliation The primary breakdown is by state or country, then by company name and political subdivision At the end of each major group is a general list showing members affiliated with schools or colleges and those who did not indicate any company affiliation The listing, for countries outside United States, is broken down generally by continents and alphabetically within the continent by countries The various countries are indexed on the preced¬ing page *-The asterisk indicates members available for consulting work Anyone desiring to be listed with AIME as available for consulting work can do so by sending a written request to the office of the Secretary.

Jan 1, 1952

By C. R. Wohrman

A melt of pure electrolytic iron with about 0.4 per cent. sulfur and 7 per cent. manganese was prepared in connection with a study of inclusions in iron. The alloy darkened rapidly when etched with a 10 per cent, alcoholic solution of nitric acid, and microscopic examination revealed the presence of a semimartensitic, semi-Widmanstättian structure (Figs. 1 and 2) closely resembling the structures found by Benedicks in his artificially prepared "meteoric iron."' The structures found by Benedicks were readily explained by the presence in his alloy of the two well-known iron-nickel solid solutions, taenite and kamacite, and of their eutectoid (?) aggregate, plessite. By analogy, one would infer the existence of similar phases in the iron-manganese alloy just described, such an inference being strengthened by the similarity displayed in many ways by nickel and manganese in their effects on iron. Iron-manganese Alloys are Regarded as Homogeneous Heterogeneity of iron-manganese alloys has not been recognized heretofore, judging from the data of standard metallographic books and those of original papers. In fact, iron and manganese are quite generally regarded as completely miscible in the solid state. Dr. Rosenhain,2 for example, writes: Alloys of group (a), of which those of gold-silver, iron-manganese, and copper-nickel are examples, when allowed to crystallize sufficiently slowly to attain their condition of final equilibrium, present a microstructure exactly similar to that of a pure metal—the homogeneous character of the molten solution is in that case so completely maintained that the microscope cannot detect the presence of any second constituent. Guillet and Portevin3 refer to the iron-manganese system as an example of the "case of metals completely miscible in the solid state."

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By Sanford Belden

My topic, Recent Developments in the Design of Electric Mine Locomotives and Mining Machinery, does not require me to go into a general review of electricity as applied to the mining industry. Interesting as that subject always is, what I might say in regard to it, by way of introduction, would be unnecessary use of your time, since such facts are familiar to all. First, we will consider the recent development of the electric mine locomotive. We may well pause for a moment to reflect upon its importance to the coal-mining industry of to-day. With the dawn of the electrical age its advent was inevitable. Our practical interest is aroused not so much by the first crude effort as by the great efficiency attained during the 30 or more years since the electric locomotive made its first appearance. To judge accurately what it means to coal mining, and through coal mining to the industrial field at large, we would have to know how many of these locomotives are in use throughout the country and their aggregate daily performance, and then compare the results with what could be expected with other forms of power. Such data are lacking, but it requires no statistician to make it evident that the electric mining machine is a tremendous factor in modern progress, and that without it the work of the world could never have reached its present magnitude. Not only has the electric mine locomotive served its own special branch of usefulness, but incidentally it has solved in the main the whole problem of electric transportation. It is but a step from the triumph of a 25-ton locomotive leading a long train of loaded coal cars from a mine to the electrification of common carriers. We may or may not be near any great change in this respect. Economical reasons may hold it back for an indefinite period. But the fact remains that in the development of our mine locomotives we have met this larger emergency, in mechanical type and efficiency, whenever it may come.

Jan 6, 1914

By M. C. Manderson

The sharp drop in world phosphate demand that took place in 1975 due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1979

By William T. Folwell

The Lucky Friday mine east of Mullan, Idaho, is an outstanding example of a property in the Coeur d’Alene district where a small and insignificant- appearing silver-lead-zinc vein at the surface has changed at depth into a large vein of great importance. The Lucky Friday vein has little if any surface expression and above the 1200 level the ore shoots are small and discontinuous. Between the 1200 level and 2450 level, the lowest developed level, the main ore shoot has shown remarkable improvement on each succeeding lower level, and today the mine is one of the major lead-silver producers in the Coeur d'Alene district. History: The Lucky Friday property is on the north side of the South Fork of the Coeur d'Alene River in sections 25, 26 and 35, T. 48 N., R. 5 E., Hunter mining district, Shoshone County, Idaho. This is about one mile east of the town of Mullan, which serves the eastern portion of the Coeur d'Alene district. The southern part of the property is crossed by a branch line of the Northern Pacific Ry. and by U. S. Highway 10. This highway is the principal road crossing the panhandle of Idaho and connects the district with Spokane, Wash., on the west and Missoula, Mont., on the east. The main portal and surface plant of the Lucky Friday mine is at an elevation of 3365 ft, only a short distance above the valley floor and a few hundred feet from U. S. Highway 10, so the mine is readily accessible for year-round operation.

Jan 12, 1958

By Pei-Yung Huang, Carle R. Hayward

IN order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. CHOICE OF SLAG COMPOSITION The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, average:2.3 45 to 47 pct FeO; 38 to 42 pct Si02; 5 to 6 pct CaO; 5 to 6 pct A1203. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-Si02-A1203, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the com¬position near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093° ± 3°C) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the resulting slag is decidedly too basic. Composition K has a slightly higher melting point (1105° ± 3°C) and a higher silica content, but this is preferred because the slag is saturated with respect to tridymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The final slag composition, therefore, was chosen to

Jan 1, 1947

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, LOUIS K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

Abbey. Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St., New York, N. Y. '21 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abeel, George H., Jr., Cons. Min. Engr 12S1, S. Canon Dr., Beverly Hills, Cal. '18 4 -Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin.. Univ. of Pittsburgh. Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 650 S. Grand Ave., Los Angeles, Cal. '82 Abele. Louis T., Min, & Met. Engr., Supt., Texas Hill Mine Coulterville, Cal. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada '31 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kan. '20 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., Member, Geological Staff of Burmah Oil Co., Ltd., Nyaunghla, Upper Burma, India. '28 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho '27 Acker, E. O'C., Met 128 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Research Lab., International Nickel Co., Inc Bayonne, N: J. '24 Ackerman, George F., Engr., Real del Monte y Pachuca Min. Co., Apt. 3, Pachuca, Hgo., Mexico '29 *Acres. T. H.. Geol. Dept., Valuation & Pet. Engrg., Richfield Oil Co., 555 S. Flower St., Los Angeles, Cal. '29 Adachi, Jinzoo Address Wanted '88

Jan 1, 1934

By J. S. Diller

In 1827, chromite was discovered near Baltimore by Isaac. Tyson, Jr., who initiated the mining of chrome ore and later (1845) the manufacture of chromium compounds in this country. From 1828 to about 1560 the United States, supplanting Russia, supplied chromite for most of the world. Chrome deposits were found also in California, and the Tyson Company shipped ore to Philadelphia by way of Cape Horn. In 1848, J. Lawrence Smith, an American in the employ of the Porte, discovered large bodies of chromite in Asia Minor. They were developed in 1865 and became the chief source of the world's supply for a number of gears. The discovery of the large high-grade bodies in New Caledonia., and later in Rhodesia, with other foreign sources, gives at present an abundant supply for all demands. For a number of years before the great war. the United States produced only a few hundred tons of chromite annually, for local use, but during the war the demand for domestic ore resulted in a production of more than 82,000 long tons of crude ore in 1918, and it was demonstrated that the United States has reserve deposits equal to a war demand of several years' duration. Now that the war is over, the country is con-serving its domestic supplies by employing higher-grade but cheaper ore from foreign countries.

Jan 9, 1919

By L. C. Aycock, J. Hunter, P. M. Lyons

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By J. Hunter, P. M. Lyons, L. C. Aycock

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By Wayne Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions, Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illus-trate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938