Search Documents

By Jean-François Stumper, Mario Moser, Mark Kruessmann, Volker Langer, Daniel Bastos Martins Cruz, Claude Meisch

The latest generation of probes and casthouse machines provide a wealth of data that has not been available a few years ago. The evaluation of this data gives direct feedback to improve the blast furnace efficiency, the equipment maintenance and design and it allows the early detection of critical or deviating process situations. A stable operation with lower operation and maintenance costs are the final customer benefits.

Oct 1, 2019

By Jim Belous

Fluid Dynamic Modeling (FDM) was used to develop solutions how to eliminate the fugitive emissions from the meltshop building and to comply with the EPA “6% opacity from the furnace operations” rule. Secondary Emission Control (SEC) system performance was simulated by an inverted 1:96 scale Plexiglas model of the entire meltshop, utilizing the negative buoyancy effects of saline solution in water. Test results show that with the installation of the internal partition wall which separates furnace aisle from the caster aisle, significant improvement of the SEC system is achievable, thereby avoiding large expenditure for the expanding a fume collection system capacity.

Aug 17, 2017

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Pedro Cunha Alves, Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Julio Aníbal Morales Pereira

The capacity of steelmaking slags (CaO-SiO2-Al2O3-MgO) on inclusion removal from liquid steel was investigated through experimental conditions. Laboratory experiments with slag and steel samples (with inclusion population known) were performed using a vertical electric resistance furnace at 1600 ºC. After the melting experiments, slag and steel samples were separated and analyzed regarding their chemical composition and inclusion population evolution. The capacity of slags on inclusion removal was evaluated based on the thermodynamics (solid and liquid phases proportion, phase composition and effective viscosity of slags) calculated using the FactSageTM 7.2. Results indicated that changes in the composition of slags (regarding CaO/SiO2 e Al2O3) presented effects on the steel cleanliness. The total inclusion density decreased in all steel samples and the removal of inclusions by slags shows a tendency to improve as their viscosity decreases (< 0.23 Pa.s).

Oct 1, 2019

By Henrique Silva Furtado

This paper presents the results obtained on the exchange of an original old blow charge model for a new up-to-date state of art global model, employing optimization techniques and process modelling, and, the results obtained in terms of fluxes consumption reduction and the introduction of user friendly tools and practices.

Aug 17, 2017

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017

By Afshin Sadri

One of the main reasons for blast furnace reline is the loss of refractory lining, particularly in the hearth and taphole regions. Intense operation of the blast furnace can result in extensive refractory wear and deterioration. This can then affect the continuity of the operation and the furnace campaign life. Novo-Lipetsk (NLMK) and Hatch developed a systematic approach to monitor the condition of blast furnace hearth linings using Acousto Ultrasonic-Echo (AU-E), a non-destructive testing system developed by Hatch. Continuous and periodic inspections of blast furnaces revealed areas with accelerated refractory deterioration, formation of elephant foot, extent and speed of refractory wear, as well as cracks and other anomalies. Improvement in coke quality, stave washing, the addition of titania, and other changes were recommended and implemented to prolong furnace life while maintaining the intensity of furnace operation. This paper demonstrates how the coordinated efforts between NLMK and Hatch resulted in prolonging the blast furnace campaign life.

Aug 17, 2017

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By Patrick Edward Connell

The next generation of the well-established 3-roll Reducing & Sizing Block (RSB), the RSB SCS® is the latest milestone in reducing and sizing technology for SBQ products. It offers enhanced bar quality, improved productivity, mill availability and economy as well as a simplified, safe and environmentally friendly operation. A newly developed modular drive concept of the RSB SCS® grants a smaller footprint in the layout, a reduced oil-lubrication volume and a simplified maintenance schedule. Intelligent engineering leads furthermore to reduced hydraulic functions of the RSB SCS®, which ensures a safe and environmentally friendly rolling. Another integral part of the RSB SCS® is an innovative stand changing concept, which allows automatic stand changing within three minutes. The new RSB SCS® also includes a Fast Remote Control (FRC) which enables the immediate adjustment of the roll gap against the rolling force (under load) within milliseconds. Size changes along the free-size range can also be made within the traditional billet gaps in less than five seconds. At the core of the future-oriented RSB SCS® is a real-time closed-loop control system called Size Control System (SCS®) acting with 3-roll stands adjustable under load (AUL) and / or the heavy duty stands. These features remarkably further improve the rolled tolerances and their reproducibility, and at the same time simplify the operation by means of an automated optimization of the process parameters for the rolled bars.

Aug 16, 2017

By Osmar de Sousa Santos

NiTi shape memory alloys (SMA) have been widely used as construction materials due to their shape memory and superelastic properties. Usually the application of the NiTi alloy is in the wire form, which is ideal shape to make springs, orthodontic arc-wire and endodontic files. Since our research group (ITASMART) started producing NiTi wires, it was noticed that NiTi SMA produced by Vacuum Induction Melting (VIM) presents carbon contamination, which is due to the melting process. Therefore, alloys rich in carbon remove titanium from matrix, forming precipitates of TiC (titanium carbide). Also, Ti2Ni precipitation removes titanium from the matrix and these two precipitates TiC and Ti2Ni can produce internal volumetric defect in the wire drawing process. Seeing the importance of NiTi wires as base of many applications, this work studies the formation of volumetric defects caused by precipitates in the wire drawing process of a NiTi wire drawn down to 0,39 mm in diameter.

Aug 8, 2018

By Wolfgang Linden

The emerging demands on higher steel grades call for improvements in the operation of production units and a corresponding increase in automated processes, and therefore international steel producers require viable functions. The avoidance of slag carry-over to secondary metallurgy processes is essential for achieving steel grade qualities and reducing alloys in order to compensate slag residues in the downstream unit. The automatic tapping procedure in BOF converters will be supported by the implementation of reliable measurements used in high-end steel plants. Automatic tapping will help to achieve the following: Reduced slag carry-over, improved yield, increased reproducibility, improved working environment and safety and operation with minimum possible crew. The automatic tapping procedure is capable of being implemented in new or retrofitted installations.

Aug 17, 2017

By Michael Brandner

HSM can be divided into different groups such as Conventional HSM with Roughing stands and HSM without Roughing stands = Mills with just finishing stands. The roll requirements for different stands are quite different. In Roughing stands the temperature of the slab is very high. Therefore the resistance against thermal wear/fatigue is the most dominating factor. Today mostly Chrome Steel, Semi HSS and HSS rolls are applied. A comparison and evaluation of such rolls will be described. In the finishing mill the tendency/wish is to use HSS rolls in all the stands. The grade HSS is defined by at least a certain amount of carbide forming elements such as V, W, Mo, Nb etc. The matrix and other precipitations can be adjusted according to the need and situation in the mill. In the pre-finishing stands the HSS is already well introduced. In the last finishing stands the original HSS tended to stick and the cobble rate increased. New development decreased the problem and gave some very promising results. In the last finishing stands beside the high performance a higher resistance against incidents is needed. Solutions in this direction including e.g. residual stresses and special core material will be discussed. Proper testing and grinding procedures can avoid losses and reduce the TCO. Data sourcing and evaluation in regards of rolling and grinding is the key for the optimization of the TCO. Several examples and comparison between different applications will be given in detail and explained. Future possibilities will be discussed as well as results of latest trials in mills.

Aug 17, 2017

By Patrick Tassot

Increased worldwide highly competition in steel market imposes innovative measure for the steelmaker targeting cost reduction and climate-friendly steelmaking process in order to have the ability to withstand the pressure of the market. At the same time the demand for high purity and highest quality steels continues to grow from year to year, especially in the sector automotive in transportation of oil and gas, in the construction Industry and in the manufacture of heavy plate. As they allow producers to be up to the requirements while allowing expanding their product mix, new secondary metallurgical treatments have become a must additionally to standard equipment elements of steel plants modern. Most of these treatments occurs in the steel ladle increasing the pressure to ensure a reliable and as possible neutral reactor. Intelligent solutions for refractory lining ladles should integrate better adaptation to the operational process parameters and the high reliability/availability at the best cost/performance. This challenge has conducted Refratechnik to develop new concepts to overcome the frontier between shaped and unshaped materials and that’s what will be covered in this paper.

Aug 17, 2017

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Edo Engel

Whereas only a handful of decades ago, typical blast furnace working volumes were below 1000 m³, such furnaces are currently designated compact or even mini blast furnaces. For certain business cases, however, small furnace sizes remain an attractive option. Decades ago, this size blast furnace would have produced a maximum of 0.3 Mtpa with its 600 m³ working volume over a campaign of up to four years. The current state of technology and operational know–how will allow a similarly sized furnace to produce over 0.7 Mtpa while achieving the multiple decade campaigns that have become familiar to steel producers in full sized operations. This level of productivity, but especially the reliability and supply security associated with mature technology, allows for integration into minimills or taking a first step towards a full scale BF–BOF integrated mill. Steel producers considering such scenarios, which are typically attractive for emerging economies, are confronted with fundamental decisions, one of which is for the technological basis for the compact or mini blast furnace to be included in the plant. This article addresses some of these decisions from an operations–based perspective. A small number of case studies is included.

Aug 16, 2017

By Renato Okabayashi Miyaji, Guilherme F. B. Lenz e Silva

As novas tecnologias de manufatura aditiva podem acelerar tanto o desenvolvimento, quanto a prototipagem na indústria siderúrgica. Dessa forma, várias etapas do processo produtivo podem ter sua eficiência melhorada, com o objetivo de se obter um produto final de melhor qualidade, gastando menos recursos humanos, operacionais, custos e tempo. Nesse contexto, este projeto tem como objetivo o aumento da eficácia do procedimento do vazamento do aço líquido da panela para o distribuidor, por meio do desenvolvimento de um dispositivo anti-vórtice para a válvula superior da panela de aço. Neste projeto foram avaliados diferentes formatos e geometrias por meio da metodologia de Planejamento de Experimentos (DOE), empregando a impressão 3D e um modelo de escala reduzida. Posteriormente, foram realizadas simulações de fluidodinâmica computacional (CFD), para melhor compreensão do fenômeno e dos resultados obtidos.

Mar 1, 2019

By Saulo Brinco Diniz

As ligas de alumínio da série 7XXX são largamente utilizadas no setor aeronáutico devido sua alta razão resistência mecânica / densidade. O que proporciona uma alta resistência mecânica para as ligas da série 7XXX é a adição de elementos de ligas e tratamentos térmicos adequados, como por exemplo o T7351. Este trabalho teve como objetivo, estudar a evolução microestrutural de uma liga de alumínio 7475-T7351 processada por laminação convencional a temperatura ambiente, e posteriormente submetida a tratamentos térmicos de recozimento para recristalização. De acordo com os resultados apresentados, a amostra que foi submetida ao tratamento térmico de recozimento para recristalização a temperatura de 500ºC durante 15 minutos recristalizou, enquanto que a amostra que foi tratada a 350ºC durante 1500 minutos teve coalescimento dos precipitados.

Oct 30, 2017

By Moacir Andretti Sabino Mota

Os componentes da carga dos altos-fornos, que majoritariamente formam a escória final, consistem basicamente da ganga da carga metálica (minério, sínter, pelota), dos fundentes adicionados (quartzito, calcário, dolomita, etc) e da cinza do redutor (carvão vegetal ou coque). A estrutura da escória é formada por um conjunto de óxidos oriundos do processo de redução metálica e das impurezas da carga. As características de uma escória para uma máxima eficiência na operação do alto-forno devem ser: baixo ponto de fusão, fluidez e baixa viscosidade, tolerância, alta dessulfuração, remoção de álcalis. Com base nos argumentos destacados acima, tornou-se necessário o estudo de um método de cálculo eficiente para a viscosidade e da temperatura de liquidus da escória do AF2 da Vallourec Soluções Tubulares do Brasil - VSB.

Oct 30, 2017

By Noan Tonini SImonassi

A indústria da construção civil e a que mais absorve mão-de-obra no Brasil, com uma significativa participação no PIB, da ordem de 15%. Em contrapartida e ainda apontada como uma grande geradora de resíduos, que variam em função da matéria-prima utilizada e também da mão-de-obra desqualificada. Dentro desta faixa de mercado, o número de edificações que empregam blocos cerâmicos como elementos de vedação ou estruturais, é bastante expressivo, principalmente pela facilidade de produção destes artefatos no Brasil. Neste trabalho buscou-se avaliar a influência dos blocos cerâmicos, quando utilizados fora de norma, em uma determinada edificação, formada por um prédio residencial multifamiliar que estava sendo construído no município de Itaperuna, RJ e se encontrava nas etapas construtivas de vedação e revestimento, cujas perdas e causas associadas foram identificadas e quantificadas.

Oct 30, 2017

By Afonso Rangel Garcez de Azevedo

A indústria da construção civil é a que mais absorve mão-de-obra no Brasil, com uma significativa participação no PIB, da ordem de 16%. Em contrapartida é ainda apontada como uma grande geradora de resíduos sólidos urbanos, que variam em função da matéria-prima utilizada e também da mão-de-obra. Dentro desta faixa de mercado, o número de edificações que empregam blocos cerâmicos como elementos de vedação ou estruturais, é bastante expressivo, principalmente pela facilidade de produção destes artefatos no Brasil. Neste trabalho buscou-se avaliar a influência dos blocos cerâmicos, quando utilizados fora de norma, desempenham nos custos do revestimento, quantificando as perdas e as identificando. Pode-se concluir que o uso de blocos fora dos padrões normativos apresenta influencia considerada nos custos de uma edificação.

Oct 30, 2017