Search Documents

By Yun Soon Han, Joo Hyun Park

Indium (In) solubility in the FeO-SiO2-Al2O3-5%CaO slag was measured under p(O2)=10¯¹¹ atm at 1573 K to clarify the dissolution mechanism of In in FeO-bearing metallurgical slag. The In solubility increased with increasing oxygen partial pressure, whereas it decreased by increasing the activity of basic oxide, viz. FeO. Thus, a dissolution mechanism of In in the FeO-SiO2- Al2O3-5%CaO slag was described by the following equation. In(s)+1/4O2(g)=(In+)+1/2(o2-) The enthalpy change of the In dissolution reaction was negative, indicating that the dissolution reaction was an exothermic reaction. This is consistent with the above reaction mechanism.

Jan 1, 2014

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

The effects of microwave roasting on separation of rhenium (Re) and molybdenum (Mo) from a molybdenite concentrate have been investigated based on evaluation of the heating characteristics of the concentrate in the microwave field. The results show that a variety of operating variables, namely microwave power, sample weight, sample geometry, roasting temperature, roasting time and atmosphere significantly impact on the volatilization rates of Re and Mo. The optimum conditions for Re-Mo separation are microwave power 1300 W, sample weight 20 g, sample geometry pellets, temperature 600 oC, time 1.5 h, and atmosphere 20%O2. Under these experimental conditions, the volatilization rate of Re reaches 88.12%, while that of Mo is just 5.15%. Microwave-assisted roasting provides an alternative route to separating Re and Mo from molybdenite concentrate.

Jan 1, 2016

By Feng Liu

A thermal upgrading process by which nickel value can be concentrated in a ferronickel alloy is a possible alternative to treat Sudbury pyrrhotite (Po) tailings with nickel content of 0.5–1.5 wt%. The basis of this process is precipitation of Ni from Po at high temperature once Fe/S ratio in the iron-deficient Po is shifted towards stoichiometric or near stoichiometric FeS (troilite) either by the addition of iron and/or the removal of sulfur. For the iron addition route, the reaction between elemental iron and nickeliferous pyrrhotite to produce ferronickel alloy and Ni-depleted iron sulfide phase plays a critical rule. In this paper, the formation mechanism of ferronickel alloy was investigated using the diffusion couple technique to better understand the nickel diffusion behavior in the iron and sulfide phases.

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the ,process, to the subsequent cleaning of the gas and to the use of the heat extracted from the gas. The method of reducing the effect of acidic ,sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms are discussed. The development of indirect recuperators using air, water or steam cooling, made 'possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process conditions".

Jan 1, 1992

By Takeshi Nagano

"Prior to discussing future trends of non-ferrous metals smelting and refining, the past developments are looked back. Social and economic environments in Japan over the past two decades are reviewed. Technological developments to comply with these environments are explained, taking for examples the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper tankhouse. After considering the factors which will influence the improvements in non-ferrous processing, future trends are forecasted generally for copper, zinc, lead, aluminum and rare earth metals. Recent development works in Japan for the future are also introduced. In the discussed area, it appears that the emergence of new innovative processes would be difficult. The progress will be made rather toward the sophistication of the existing technologies, utilizing the advancement of the related technologies such as computers, electronics, etc. IntroductionThis paper discusses the future trends of non-ferrous metals smelting and refining on the occasion of the international symposium, ""The Metallurgical Processes for the Year 2000 and Beyond"".It is considered that the improvement of technology is greatly influenced by the social and economic environments which surround it. From this standpoint, review was made of Japanese case over the past two decades. Various new technologies were developed also in the non-ferrous metal world to comply with the requirements under the above environments. The examples are described in the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper electro-refining.After foreseeing the major factors which will affect the technological developments in the future, the trends are forecasted for copper, zinc, lead, aluminum and rare earth metals generally. Some development works in Japan, which will give suggestions for future trends, are also introduced in some detail."

Jan 1, 1988

By Adelana Adetunji

Ilmenite ore samples obtained from Dankoli in Zamfara, North Western Nigeria has been characterized using Energy Dispersive X-ray fluorescence (EDXRF) technique, X-ray diffraction (XRD) technique and the Neutron Activation Analysis (NAA) technique. The major constituents in the ore were quantitatively found to be TiO2 and Fe2O3 in concentrations of about 60wt% and 31wt% respectively. These occur in the forms of magnesian ilmenite (Fe, Mg)(Ti, Fe)O3, pure ilmenite (FeTiO3), and barium copper yttrium oxide (Ba2Cu3YO6.56) minerals. Other constituents/impurities in minor or trace quantities include MnO, Ta2O5, Nb2O5, Wo, SnO2, Hf, Zn, V, Zr, Co, Pb, Br, Al, Rb, Y, Th and U.

Jan 1, 2006

By Linda C. White

The use of red mud, a waste product of the ?Bayer? process for bauxite refining, was investigated for its arsenic removal effectiveness from aqueous solutions under various conditions. Red mud efficiently removed As(III) between a pH range of 7.6 and 9; and As(V) in the pH range between 5.5 and 6. Pre-washing of the red mud with salt water considerably improved its arsenic adsorption capabilities. With appropriate red mud dosage, the residual arsenic in solution was decreased below the regulated acceptable arsenic limit (0.1 mg/L) from aqueous industrial wastes. The arsenic adsorption followed first-order rate kinetics and fitted the Langmuir isotherm model. Results suggest that red mud is potentially a useful adsorbent for removal of arsenic from contaminated water or industrial waste solutions.

Jan 1, 2003

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the process, to the subsequent cleaning of the gas. and to the use of the heat extracted from the gas. The method of reducing the effect of acidic sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms?are discussed. The development of indirect recuperators using air, water or steam cooling, made possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process? conditions".

Jan 1, 1992

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By S. N. Sinha

The distribution coefficients of lead and silver between copper and matte phases have been measured at two different temperatures. Experiments covered the ranges of 0.009-1.8, 0.07-0.13, and 0-11 wt pct lead, silver, and iron in matte, respectively. The distribution coefficients of lead have been measured at 1405 and 1505 K and correlated with lead and iron concentrations in metallic copper and matte. The values of the distribution coef¬ficient of lead between copper and iron-free matte, at infinite dilution of lead, have been determined to be 3.60 and 4,06 at 1505 and 1405 K, respectively. The distribution coefficient of silver between copper and iron-free matte is independent of silver concentrations and has been measured to be 2.13 and 2.21 at 1400 and 1500 K, respectively. For an iron-bearing matte, the distribution coefficient of silver has been correlated with iron concentration in the matte at both 1400 and 1500 K. From the measured values of distribution coefficients, the Raoultian activity coefficients of PbS and AgS0.5 in copper-saturated matte have been calculated. At infinite dilution, the following equations correlating the Raoultian activity coeffici¬ents of PbS and AgS0.5 with matte- composition and temperature have been obtained: log Y° PbS =1.515 + 1080/T 0.14 NFes lbS Fog YAgS = -0.074 - 425/T + 0.09 NFes. - 0.5

Jan 1, 1983

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By S. H. Castro

The El Teniente molybdenite plant (Chile), with a nominal capacity of 3,200 tpd of bulk Cu-Mo concentrate, produced approximately 3,385 metric tonnes of Mo during 1998 by using the phosphate Nokes process (LR-744 reagent). This is the only Chilean moly plant which traditionally has depressed copper and iron sulfides with LR 744 reagent, which is a hydrolysis product of P2S5 and NaOH. El Teniente's ore Mo grade is 0.02%Mo and is concentrated to 0.45%-0.50% Mo in bulk Cu-Mo flotation. Subsequently, molybdenite is floated by selective flotation to depress Cu and Fe sulfides, such as chalcopyrite, bornite, digenite and pyrite, to produce typically a 49%-50%Mo molybdenite concentrate. An optimisation program during the last two years was undertaken to improve molybdenite recoveries. Current molybdenite plant technology at El Teniente and use of phosphate Nokes in the process process is reported. Use of phosphate Nokes reagent has increased average Mo recovery from 70.5% in 1977 to a mean 74.7% for the first 4 months of 1999. The global Mo recovery, including bulk flotation, incresed from 42.3% in 1997 to 46.8% in 1998, with a projection of 55.5% for 1999. Mo production per year has increased from 3,181 tons in 1997 to 3,385 tons in 1998 and a projected 4,000 tons for 1999.

Jan 1, 1999

By Elders. Wilfred A.

Petrological and geochemical methods, the utility of which has long been established in the mining industry, are proving useful and cost-effective in elucidating the thermal evolution of active geothermal fields. In return, they yield insights into sulfide-silicate equilibria, mass and energy transfer in convecting hydrothermal systems, and the genesis of hydrothermal ore bodies. Within the Plio-Pleistocene sediments of the delta of the Colorado River, in the Salton Trough, several active geothermal systems are known. Temperatures vary from 100-365°C, at less than 2 km depth, and salinities vary from 3,000 to 280,000 ppm, total dissolved solids. The hydrothermal alteration causes marked induration of the sediments, producing greenschist facies metamorphic minerals, including hydrothermal ore minerals. Subsurface authigenic minerals show strong correlation with increasing temperature. A typical sequence in sandstones is (below 150°=C) montmoril-lonite-kaolinite, (above 180°C) chlorite + illite, (above 225°C) calc-alumino-silicates, (above 325°C) biotite. There is a transition from porosity-dominated\to fracture-dominated permeability in the hottest and deepest geothermal reservoirs. This regular series of minerals provides a practical tool during exploration drilling. From drill cuttings, we can make predictions on reservoir temperatures, useful in making decisions on well completion. Other types of geothermometry we have employed include light stable isotopes, fluid inclusions and vitrinite reflectance measurements. A combination of these techniques not only improves our temperature predictions, but together with fission tack annealing studies, permits us to model the dynamics of temperature change and fluid flow in these geothermal reservoirs.

Jan 1, 1981

By Denis Shishin

The pyrometallurgical production and recycling of non-ferrous metals involves the use of complex feed stocks, having awide range of chemical compositions from sources that include mineral sulphide concentrates, high value obsolete materials and process wastes. The commercial viabilities of these operations hinge on the ability to extract value from these materials. Increasingly, modern computer-based tools are used to describe and predict process outcomes, including mass and heat balances, the partitioning of elements and phase equilibria. At the heart of these predictive tools are thermodynamic databases that describe the fundamental chemical properties of a system and all the components present. A comprehensive research program has been established to develop an accurate, self-consistent thermodynamic database describing all gas-slag-matte-metal-speiss-solid phases in the system Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Sb-Sn-Ag-Au). The database can be used in conjunction with the FactSage computer platform. The accuracy of the database and its application to industrial practice is demonstrated.

By L. Petitnicolas

The experimental study of nitrogen absorption and its removal from a liquid Ni-20%Cr alloy at 1873 K has been undertaken, using an experimental, apparatus based on the Sieverts technique in order to determine the solubility of nitrogen in the alloy. as well as the kinetics of nitrogen transfer across the gas/melt interface. Experiments show that nitrogen solute equilibrium content can be calculated using the Sievens law. Measurements point out the nitrogen absorption reaction rate to be well described by first order kinetics, whereas experiments on nitrogen removal reveal that the rate is better expressed using a second order equation.

Jan 1, 1996

By V. I. Lakshmanan

The demand for elements such as nickel, cobalt, titanium and gold in various applications has increased significantly. Innovation to recover these elements now plays a major role in metallurgical processes as established technologies have challenges in treating the types of ores that are available while meeting the increasingly stricter environmental regulations. Alternative chloride based processes have been developed that can be used to recover the value elements from the available feed stocks with potentially lower environmental impact. Chloride-based hydrometallurgical processes have several advantages, including higher leachability of complex ores/tailings and relative stability of chloro-complexes of the metals. Process Research ORTECH Inc. (PRO) has developed mixed-chloride process flowsheets, where innovative solvent extraction process steps are used for the separation of nickel, cobalt, titanium and gold from their respective chloride solutions. This paper will discuss the potential aqueous chloro-chemistry of these metals and separation reaction mechanisms involved in the solvent extraction process.

By Michael G. Mayer

Since its invention in 1859 various designs of lead batteries have evolved to meet commercial needs for traction applications and standby power. In recent years major developments have taken place in lead alloys and the chemistry and mechanical design of industrial lead batteries. These are reviewed in relation to their commercial application together with the new type of maintenance free gas re-combination lead-acid batteries which are opening so many new markets for lead.

Jan 1, 1990

By Z. M. Zheng

Cyclic voltammetry, potential step, and ac impedance techniques were applied to study the electrochemical reaction of arsenopyrite in chloride solutions. The relationship between anodic current density and time in potential step measurements indicates that the oxidation of arsenopyrite is irreversible. The results of the constant potential coulometry show that the stoichiometric factor of the total electron involved in the overall reaction is 14. It is proposed that the dissolution of arsenopyrite is retarded by coverage of sulfur produced in the reaction as an intermediate product. The measured results of ac impedance strongly support the proposition. The proposed reaction mechanism also explains satisfactorily the charging current density and Tafel slopes measured in potential step measurements.

Jan 1, 1995

By W. F. Drinkard

Many in the environmental movement have focused on this element. But, nothing they or anyone does will change the amount of arsenic in the world. This report is on actual commercial plants that we developed and operated to recover or stabilize arsenic values from metallurgical dusts from gold and copper pyro operations and arsenical gold bearing ores. When they were available gold and copper values were recovered. Our experience in arsenic extends over thirty years. My first corporation, Mineral Research & Development Corporation was the first in North America to manufacture the then new CCA (copper-chrome-arsenic) wood preservatives. This class of wood preservatives proved to be so effective that it made wood into an entirely new material of construction. It is not uncommon for wood properly treated with arsenical CCA preservatives to last for thirty; forty, and sixty years. Over a hundred years have been projected in some field tests. Hundreds of thousands of trees have been saved. Millions more trees would have been saved had environmentalists not decided that their arsenic phobia was more important than trees. There are several variations of CCA. The most popular is CCA-C. Its formula is: CrO3 . . . . . . . . . . . . . . . . . . . 47.5% CuO . . . . . . . . . . . . . . . . . . . 18.5% As2O5 . . . . . . . . . . . . . . . . . 34.0% Until recent restrictions were placed on the consumption of arsenical wood preservatives, annual consumption in North America was about 150,000,000 lbs./yr. About 64,500,000 of arsenic as the pentoxide was safely consumed this way. World CCA consumption has been about double the above figures or 300,000,000 lbs. as 100% CCA and 129,000,000 lbs/yr as As2O5. Close to 100% of all the arsenic used in wood preservatives is derived from gold or copper processing. The valence of arsenic required for CCA wood preservatives and many other markets is the same valence that is required for stabilization. The economic challenge is how to get there. We have built and operated eleven plants to oxidize arsenic trioxide to its pentavalent form. Most of these have been classic in that they used a common oxidants such as hydrogen peroxide or nitric acid to achieve this.

Jan 1, 2005

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994