Search Documents

By Patrick R. Taylor

Coatings of TiCIFe have been produced by Reactive Plasma Spraying using ilmenite ore concentrate as the feedstock powder and methane as the reactive gas. A free energy minimization analysis of the ilmenite-methane system is presented. The coatings have been characterized by x-ray diffraction and SEM. The microstructure of the coatings indicates good interparticle cohesion. The composition of the coating is deficient in iron compared to the initial Fe to Ti ratio found in ilmenite.

Jan 1, 1998

By Tan Pengfu

By using computer-aided techniques of equilibrium calculations for multicomponent and multiphase systems, a computer model has been developed to simulate QSL, KIVCET and Outokumpu flash lead smelting processes. A mathematical description is studied using two zones or three zones, namely smelting zone and slag reduction zone for QSL furnace, or offtake shaft zone, smelting shaft zone and electric furnace zone for KIVCET furnace. The amount of each component in lead, slag and gaseous phases under equilibrium is calculated by using the data of free energies of formation and activity coefficients. The predictions by the present computer model are compared with the known data from QSL-Plant at Korea Zinc Co. in Korea, KIVCET-Plant at Nuova Samim Co. in Italy and Outokumpu Co. in Finland. The agreements between the computer predictions and the known data are excellent, so that the present computer model can be used to monitor and optimize the actual industrial operations of direct lead smelting.

Jan 1, 1998

By Deepak Malhotra

Rosario Dominicana, S.A., operates a gold processing complex at Pueblo Viejo, northwest of Santo Domingo (Dominican Republic). The plant processes approximately 10,000 mtpd of oxide gold-bearing ore with a work index of 11 kWh/mt. The ore hardness has increased to about 17 kWh/mt. Metallurgical auditing of the plant was conducted? to find ways to modify the circuit to process hard ore without sacrificing throughput. In addition, unit operations were optimized to increase recovery and reduce operating cost,. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1989

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.

By Aïda Espinola

Decontamination of synthetic solutions containing cadmium ions using coconut fibers in natura was investigated in laboratory scale. Cadmium ions, a serious pollutant of water ways, where it is detrimental to the environment, may be absorbed by fish and mollusk used as food, which will, eventually, poison humans; these ions are usually present in minero-metallurgical and electroplating industrial effluents. Usually employed for the aqueous effluents treatment are chemical precipitation, adsorption and electrolytic processes. Precipitation is not effective for cadmium removal, because of the high KpS of the cadmium hydroxide, which requires high pH; only sulfide would be efficient in cases of very small amounts. Some vegetal refuses have shown to be practical for absorption processes of several metallic ions. We have applied coconut (Cocos nucifera) shells, which are extremely abundant over most of the extensive Brazilian coast, in the removal of cadmium: it has been verified, in our laboratory, that the surface of the fiber of this coconut is rich in chemical compounds which are active scavengers for Cd2+. For the optimization of the process, hydrosoluble components existing on the surface of the fiber, which may be deleterious, were previously washed out by water, and variables, such as the pH and the proportion of mass of fiber to volume of solution, were adjusted. As much as 99% of the initial contaminant metallic ion has been eliminated, resulting a solution to be discarded which contains ca. 0.1 ppm; this attends to the maximum impurity legally admitted by the environmental control agency of Rio de Janeiro, FEEMA, for cadmium ions in aqueous effluents to be disposed in rivers and in the Guanabara Bay area.

Jan 1, 1998

By Gervais Soucy

During mineral and industrial processing, contaminated wastewater can be generated such as cyanide liquors (free species or in complex form). This paper presents the treatment of cyanide solution derived from the aluminum industry, by direct contact of the solution with thermal plasma in a novel reactor. The reacation energy is provided by a plasma submerged in solution which allows direct contact between the plasma and the solution to be treated. The scope of this' study was to determine the feasibility of treating free and complex cyanides in solution through mini-pilot scale operations. An innovative reactor was designed and fabricated to provide stable: process operating conditions. Many parameters were studied. These experiments permitted the evaluation of the kinetics of complex cyanides decomposition under thermal plasma conditions. At atmospheric pressure (temperature about 100°C), the rate of cyanide decomposition by thermal plasma was 12 times greater than that of thermal hydrolysis in a plug flow reactor et the same temperature. The improvements in the decomposition rates are attributed to high thermal gradients at the plasma liquid interface and photocatalysis induced by the plasma UV radiation.

Jan 1, 1998

By Reinhard F. Dobner

After a short introduction about the HK's secondary smelter process and explanations concerning the anodes produced the regulation and buffering of bleed will be described and the principles of technology for processing of bleed will be presented. Modernization aspects, especially installation equipment, and the different types of evaporators used will be described in detail. Besides, experience made with acid-resistant materials - stainless steel, enamel, plastics - will be reported. Environmental aspects such as water and air pollution will be outlined briefly and in conclusion the quality of products obtained as well as quality control will be presented.

Jan 1, 1997

By Theodore Ineich

The “BIOMOre” project aims to prove the technical feasibility of indirect in situ bioleaching of sulfide minerals contained in a deep underground deposit, by bringing together the disciplines required to make a success. The underground location in Poland was provided by project partner KGHM inside an operating copper mine. Key components of this project were the design and construction of a pilot plant, and its operation in an underground environment. This project also included a ∼250 t (100 m3) fragmented rock reactor hydraulically connected to the pilot plant. The pilot plant consisted of several tanks and pumps, a fluidised bed ferric iron generating bioreactor containing immobilised acidophilic iron oxidation biomass, and all the required instrumentation and utilities. Before the bioleaching phase could start, the rock reactor had to be flushed continuously firstly with water to remove chloride salts that are corrosive and also harmful for the bacteria used in the bioreactor, and secondly, with sulfuric acid solution to react with the carbonates present in the ore matrix. This paper summarizes the design, construction, commissioning, and operation of the pilot plant.

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By I. D. Reznik

The flowsheets of converter matte production from sulphide copper - nickel and oxide nickel ores on Severonickel and Yuzhuralnickel integrated ,;corks are given. The cobalt behaviour in electrosmelting and autogenous ore smelting, converting and converter slag cleaning is observed. A list of acticles published in the 80 th is given.

Jan 1, 1993

By Hiroyuki Matsuura, Fumitaka Tsukihashi

"Emission of CO2 gas from steelmaking industry covers more than 12 % of total CO2 emission in Japan. Though many efforts have been made to curtail energy consumption and high energy efficiency of Japanese steel production process has been achieved so far, further reduction of CO2 emission is strongly requested to develop sustainable steel production process and produce “green material”. Recently, authors have proposed the innovative hydrogen production process, in which water vapor is reacted with discharged steelmaking slag to produce hydrogen gas. This reaction can be achieved without any external energy source and operated by huge thermal energy associated with steelmaking slag and FeO or unrecovered Fe droplets that are relatively rich in the slag. In this paper, thermodynamic calculation results with various initial conditions in terms of hydrogen productivity were presented. Laboratory-scale experiments were also conducted to clarify the validity of thermodynamic calculation and the reaction rate in realistic conditions.IntroductionIronmaking and steelmaking process from iron ore through blast furnace and BOF is an essential steel production route for Japanese steel industries to supply high quality steel products in large quantity to society stably. Blast furnace – BOF process requires huge amount of fossil fuels such as mainly coal, resulting the emission of considerable amount of CO2 gas. Since the emission of CO2 gas from steel industries, about 147 Mt (FY2011), accounts for approximately 12 % of domestic CO2 gas emission in Japan (FY2011),[1] it is an urgent issue for steel industries to develop environmental-friendly ironmaking and steelmaking process and reduce CO2 emission. Various kinds of gases and by-products generated from ironmaking and steelmaking processes have been recycled as much as possible at present. Enormous thermal energy is also generated from processes and released to surrounding atmosphere as various forms such as sensible heats of gases, molten steels or by-products, and as heat losses. However, these energies are not utilized before final dissipation to atmosphere. Although various technologies to utilize thermal energy from ironmaking and steelmaking processes have been attempted to develop, practical application of these technologies has not been achieved because the thermal energy is not always useful as an energy source. In steelmaking process by BOF, fluxing agent such as CaO is added during reefing and thus about 100 kg/t-steel of steelmaking slag are generated. Since the steelmaking slag is discharged at temperature range between 1873 and 1923 K after discharge of refined molten steel, it also has large thermal energy. Amount of generated BOF slag is 11.0 Mt/y (FY2012) in Japan.[2] Assuming the amount of steelmaking slag is 10 Mt/y and its average heat capacity from room temperature to 1923 K is 1 kJ/kg·K,[3] unutilized heat is estimated to be 16 PJ/y, which is equal to annual energy consumption of 420 thousand families in Japan.[4]"

Jan 1, 2014

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By Yasuhiro Konishi

Hydrolytic stripping is the process in which metal ions are simultaneously stripped from a loaded cation-exchange solvent extractant and precipitated as oxides or hydroxides. Hydrolytic stripping is usually effected by contacting the loaded organic phase with water at elevated temperatures. The possibility of using hydrolytic stripping to prepare ceramic powders with controlled size and morphology is now being evaluated for different systems, using carboxylic acid extractants. As part of this work, mathematical models were developed to describe the kinetics of nucleation and growth of nickel ferrite particles. This paper describes the development of the models, along with estimation of key parameters appearing in the rate equations from experimental data.

Jan 1, 1990

By Adolf Mikula

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of ternary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth, silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe element.

Jan 1, 2003

By J. Avraamides

Some operational difficulties have been encountered in the transfer of carbon-in-pulp technology to Australian conditions. Many gold mines? are located in remote and arid areas where the available ground water is highly saline. There is a gradual depletion of free milling oxidised gold ore reserves resulting in the necessity to treat deeper primary sulphide .deposits which can be refractory. Some near-surface ore-bodies and tailing dumps are contaminated by natural vegetative matter which can interfere with the adsorption of gold from the cyanided pulp,. Advances which have been? made include potable water conservation in elution, a new type of regeneration kiln, inter-stage screens, alternative leaching systems transportable carbon-in-pulp plants and efficient open-cut mining methods. Academic and applied research is well supported by government and industry and the results are normally rapidly disseminated and put into practice by the gold mining industry.

Jan 1, 1989

By M. J. King

The Chino Smelter embarked on a program to reduce smelter emissions. Fugitive sulfur dioxide and particulate emissions were reduced by (i) removing the flash furnace settling chamber and (ii) installing a baghouse, to treat converter secondary emissions. Neutralization plant capacity was increased, to accommodate increased flow from the flash furnace off-gas cleaning system and to reduce costs.

Jan 1, 1998

By Dong-dong Liu, Jian-ping Niu, Qi Liu, Shu-sen Cheng

A numerical model was developed to simulate the three-dimensional heat transfer in the belly and lower shaft region of the blast furnace wall consisting of copper steel composite stave, packing and shell. The temperature distribution of copper steel composite stave without the slag layer or refractory lining was investigated and then compared with the copper stave. The results showed that copper steel composite stave can satisfy the requirement of overheatingfree and had an analogous heat transfer behavior as copper stave but more stable cooling intensity. This model had been validated by the good agreement between the computed and measured temperature in the thermal test.

Jan 1, 2015

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

By Karl-Michael Zett, Marcus Kirschen, Ashraf Hanna

"Bottom purging systems are well established practice in refining metallurgy and an increasingly important technology for the EAF process in steel industry. Direct bottom purging provides efficient mixing of the entire melt volume, increases turbulence intensity in the melt, and improves mass exchange of alloy additions or oxygen. Continuously rising columns of dispersed gas bubbles helps to increase removal of volatile components carbon monoxide and hydrogen avoiding boiling retardation. Direct purging (DPP) systems provide cost benefits especially for EAF processes where metallurgical constraints have to be considered, e.g. for alloyed and stainless steel production, foundries. Case studies are presented.IntroductionCurrent EAF Technology and Production Constraints in Steel IndustryApproxinlately 30 % of steel, 446 Mio. tonnes in 2011, was melted in the electric arc furnace (EAF) with increasing tendency due to its large flexibility in production volume and raw materials. With recent increase of prices for ferrous raw materials the requirements for production of high quality steels from low quality scrap, direct reduced iron (DRI) and blends of ferrous raw material in various qualities increased. Maximum yield of ferrous raw material, oxygen, carbon, and alloys and minimum energy costs are of high importance. At modem high productivity levels even small process improvements provide considerable cost savings. Such improvements are caused, e.g., by efficiency increase of mass and energy transfer in the EAF. Optimization of flow pattern in the steel bath is therefore important for efficient melting of scrap and DRI and high homogeneity of the melt [1-4]."

Jan 1, 2013