Search Documents

By Michael Gauna, Christopher Mark

"Underground coal mining in the U.S. is conducted in numerous regions where previous workings exist above and/or below an actively mined seam. Miners know that overlying or underlying fully extracted coal areas, also known as gob regions, can result in abutment stresses that affect the active mining. If there was no full extraction, and the past mining consists entirely of intact pillars, the stresses on the active seam are usually minimal. However, experience has shown that in some situations there has been sufficient yielding in overlying or underlying pillar systems to cause stress transfer to the adjoining larger pillars or barriers, which in turn, transfer significant stresses onto the workings of the active seam. In other words, the overlying or underlying pillar system behaves as a ""pseudo gob."" The presence of a pseudo gob is often unexpected, and the consequences can be severe. This paper presents several case histories, summarized briefly below, that illustrate pseudo gob phenomenon:• Pillar rib degradation at a West Virginia mine at 1100-foot (335 m) depth that contributed to a rib roll fatality.• Pillar rib deterioration at a Western Kentucky mine at 570-foot (175 m) depth that required pillar size adjustment and installation of supplemental bolting.• Roof deterioration at an eastern Kentucky mine at 1300- foot ( 400 m) depth that stopped mine advance and required redirecting the section development.• Coal burst on development at an eastern Kentucky mine at 1700-foot (520 m) depth that had no nearby pillar recovery.• Coal burst on development at a West Virginia mine at the relatively shallow depth of 1100 feet (335 m) that also had no nearby pillar recovery.The paper provides guidance so that when an operation encounters a potential pseudo gob stress interaction the hazard can be mitigated based on an understanding of the mechanism encountered.INTRODUCTIONThe U.S. underground coal mining industry has conducted mining in multiple seam environments, where the active mining has underlying or overlying old workings at varying interburden distances, throughout its history. Often no serious consequences arise from the multiple seam mining. However, sometime mines have been confronted with hazards from underlying or overlying workings that include localized roof and rib failure, pillar system failures through propagating roof falls and floor heave, and also pillar bursts."

Jan 1, 2016

By Timothy Batchler

"Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance.This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) as part of manufactures' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs dual-walled bag designs to the support capacity, stiffuess, load shedding events, and yield characteristics.INTRODUCTIONDeveloped in the 1990s, the first major use of pumpable supports systems in U.S. longwall operations was in the support of bleeder entries (Barczak, Tadolini, 2008). Since then, they have been utilized as yieldable concrete supports to provide a safe working environment for longwall mining gateroads, bleeders, and emergency escapeways while also maintaining adequate ventilation pathways. The basic structure of pumpable roof supports has remained unchanged over the years. Formed in place with a twopart fast-setting grout, the support material can be pumped into a containment bag from several thousand feet away often through surface boreholes. The containment bag then acts as a form to fill the support and provides confinement to the grout during loading and after failure. Pumpable roof supports provide full contact with the mine roof and floor, which eliminates the need for secondary material to establish proper roof contact (see Figure 1). They provide a high peak load capacity and a sustained, confinement controlled yield behavior while maintaining stable ground conditions, which is essential to underground mining operations."

Jan 1, 2016

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By Yongping Wu

The steeply dipping coal seams in this paper refer to those with the angle of inclination ranging from 35° to 55°. The reserves of the steep coal seams account for approximately 15%~20% of the total coal reserves in China. In the past 12 years, the top-coal caving mining method had been used to mine the steeply dipping thick (11.5-16.4 ft or 3.5-5.0m) coal seams. However, the mining process of top coal caving is complex with low recovery rate and nearly 30% of coal was wasted. Those problems can be solved by using the single pass large mining height (11.5-16.4 ft or 3.5-5.0m) method. But the movement of the overlying strata around the mining face area of large mining height is complex and it is hard to control the stability of ?rock-shield support? system. Therefore, field measurement, numerical simulation and physical (similarity material) simulation methods were used simultaneously to analyze the strata movement, roof structure and rock-shield support interaction characteristics. The results indicate that strata movement, which is the same as mining the steeply dipping seams with conventional mining heights, is asymmetrical about the dipping direction of the face; deformation, failures, and movement of the surrounding rocks are more intense; the roof weighting interval decreases; the weighting intensity increases significantly; and face sloughage occurs frequently. In the gob, the space for sliding and rolling of the roof increases; the broken main roof tends to form an anti-dip pile structure; the backfilling and compactness of broken roof increase at the lower portion of the face, thereby inducing significant unbalance in stress distribution between the upper and lower portions of the face. The overlying strata above the face form a multi-level step structure. The characteristics of contact and loading of roof-shield support system are more complex. The range of shield load variation is larger, and interaction between shield supports occurs frequently. Anti-toppling and anti-sliding devices at the face become more difficult to implement. The research results provide a theoretical basis for the mining practices in the steeply dipping thick seams with a large mining height. The practice in panel 25221 of 2130 coal mine indicates that the accident rates have been greatly reduced and good technical and economic benefits have bee realized.

Jan 1, 2014

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Robert A. Stansbury

The No. 14 Mine of United States Steel Corp- oration is located at Munson, West Virginia, in &Dowell County. The mine was originally assigned 7,530 acres of Pocahontas 3, 4 and 5 Seams. Production began in 1948 with a listed reserve of 64,500,000 in place tons. It was originally intended to superimpose the 4 Seam workings with the 3 Seam and mine the two simultaneously to minimize the effects of one seam on the other. Roof control problems and economic conditions led to the discontinuance of 4 Seam workings in 1958 and again in 1980, after reopening in 1972. With room and pillar mining continuing in the 3 Seam, the majority of the 4 Seam reserves have been undermined. The mine began operation using track mounted conventional equipment. Off-track conventional equipment was next used, and in 1957 continuous miners were introduced. Since this tie, continuous miners on room and pillar work have been exclusively used with the exception of a brief shortwall trial in the 4 Seam in 1975. By mid 1982, 3 Seam mining will have been completed, leaving an estimated 42 million in place tons of 4 and 5 Seam coal as the focus of mining efforts. Plans for the subsequent reopening of the 4 and 5 Seam workings have been scheduled for June of 1981. With the resumption of mining, management is faced with solving the roof support problems caused by both the inherent physical conditions and undermining.

Jan 1, 1981

By Liang Yin-Huai

In Fuxin Coal Mines, there are more than 20 million tons of coal buried under seasonal streams. The coal seams are mostly shallow. We have mined more then 50 mining blocks distributed in 5 coal mines. Their natural conditions are different, and the consequences are also more or less different. However, no stream-water-inrush accidents under regular mining conditions are the same. There were 3 exceptions. They were caused by unexpected roof caving which made valleys or alluvia subside as funnel-like cavities and let in inrush of stream flow. The key to our success in mining shallow under-stream coal seams, according to our analysis, is that valleys or alluvia subside gently and basically evenly with contractible tension fissures and that fissures both in valleys or alluvia and in rock seams are blocked up or sealed by cohesive deposits either from alluvia or rock. This paper treats: (1) some typical illustrations of mining shallow coal seams of different occurrences under streams of different sizes, flowing capacities and valley structures, (2) observations of the height of caved and fissured zones and subsidence of valleys or alluvia, (3) observations of underground water flow before, during, and after mining and the fluctuation with respect to stream flow, (4) observations and analyses of blocking up of fissures caused by mining, and (5) feasibility of mining shallow under-river coal seams.

Jan 1, 1990

By Gary R. Corbett

The federally owned Cape Breton Development Corporation (CBDC) mines approximately 2.5-3.0 Mt of coal per annum from its Phalen Colliery. As part of an ongoing process to become more commercially viable the Corporation has implemented changes in its support method, namely, the transition from traditional steel set inseam supports to roof bolts as primary support in the single entry longwall retreat drivages. During 1991 and 1992, a monitoring program was implemented by the Cape Breton Coal Research Laboratory (CBCRL) to determine the loading on support systems and ground reaction in the gateroads in front of the retreating longwall faces of the 4 East and 5 East panels at Phalen Mine. The 4 East gateroad had been supported by steel sets alone. The 5 East gateroad had been supported by steel sets as well as roof bolting and strapping of the gateroad roof. Steel sets in both gateroads were instrumented with strain gauges and load cells to record support reaction to the retreating face abutment pressure. Multipoint borehole extensometers and multipoint strain gauged roof bolts were installed in the gateroad roof to monitor strata displacement and bolt loading above the gateroad as the longwalls retreated. This paper describes the details of the instrumentation and monitoring techniques utilized during this program and discusses the results, trends and differences observed in the two differently supported access roadways. Work on future data acquisition instrumentation is also briefly described.

Jan 1, 1993

By Pier Paolo Manca

The investigated area lies close to a large town and covers an area of about lkm2. The mine was worked at depths ranging from 5 to 100 meters but mining operations actually ceased some 50 years ago. There are seven coal seams, each one to two meters thick, overlain by sedimentary rocks in a strongly faulted area. Different kinds of subsidence have occurred, crown holes, shallow depressions and hummocky ground. The results of rock mechanical characterisation (RMR method) in the area have been used to define three different types of numerical model (FLAC 2D). A large numbers of simulations has been performed to solve three different problems at three different scales: to determine the, mechanical properties of the roof rock and overburden involved in the subsidence process, to assess the crown hole subsidence potential and to define the properties of the beam foundations.

Jan 1, 1999

By Garth Kuhnhein

The Black River and Maysville underground limestone mines operated by Carmeuse Lime and Stone, Inc. in northeastem Kentucky are two of the largest underground limestone operations in the United States. The combined output of these two options has consistently averaged over 5.5- million tons per year for the last decade. The mines operated beneath 650-ft and 1,200-ft of overburden and are affected by high horizontal stress. In 1982 changes to the mine design were made at the Maysville mine to improve ground conditions. A series of design changes were initiated in 2002 at Black River to improve ground conditions. This paper reviews the results of the changes made at Maysville, recent horizontal stress measurements conducted at the Black River mine, and the recent modifications to the Black River mine design. Roof fall statistics at both operations are used to compare the distinctly different mine layouts used at the two mines.

Jan 1, 2004

By Zhanjing Yu

Longwall ground behavior in the Illinois Coal Basin was studied in the past (1, 2, 3). Most of the past studies, however, were concentrated on either surface subsidence or underground structural behavior. In this study, both surface and in-mine ground behaviors are considered, which include: 1) stress and deformation characteristics in the chain pillars; 2) roof and floor deformations; 3) surface subsidence characteristics, including time effect; 4) relationship between the surface subsidence and underground strata behavior; and 5) the ultimate hearing capacity underneath the chain pillars. Field measurements and tests were conducted and the data were analyzed using both analytical and statistical methods. The findings in this study can he used by mine operators in the Illinois Coal Basin for longwall ground control planning and design.

Jan 1, 1994

By Maleki. Hamid

The U.S. Bureau of Mines implemented an inte¬grated static and geophysical monitoring program in a southern Wyoming mine to study changes in seismic wave propagation properties in roof strata. The purpose was to develop techniques to assess roof stability problems. The work consisted of record¬ing deformation and stress histories and calcu¬lating seismic velocity profiles. In addition. geology and roof conditions were mapped; the in¬struments were initially installed at the develop¬ment face; monitoring continued until the mecha¬nized retreat face retreated within 60 m of the instruments. Mining geometry consisted of a three-¬entry gate system using 5.2-m-wide pillars at depths of 426 m. Results were analyzed using stan¬dard history plots, velocity tomographs, and numer¬ical modeling techniques. Changes in velocity. frequency, amplitude, dynamic elastic modulus, and dynamic Poisson's ratio were related to roof defor¬mation, fracturing, and support requirements. A reduction in seismic velocity of 17 pct occurred after 60 mm of roof deformation following installa¬tion of supplementary support. Static measurements revealed significant dilation in the mine floor, spreading to the pillar and the mine roof. Failure was initiated in the floor as a result of uniform pillar penetration.

Jan 1, 1993

By Leigh Sharpe

Dunng the last 5 years a United Kingdom colliery has utilised a yielding-pillar configuration to extract a relatively thick coal seam at a depth of 640 m. As part of ongoing research into the siting of roadways adjacent to extracted longwall panels, seved field monitoring sites were established at differing locations to investigate roadway stability and yielding-pillar performance. Characteristic roadway deformation has been identified together with strata softening pathways which indicate the temporal increase in the height of softening into the roadway roof. In the assessment of such a complex problem numerical modelling, using FLAC, has been shown to contribute vital additional information, and provide further insights into the mechanisms controlling strata behaviour.

Jan 1, 1998

At any given lime, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes in the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (l) study the interaction between MRS's and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS's have capacities of 5,340 and 7,120 kN (600 and 800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS's help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-scam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4) geologic structures, and (5) panel layout designs and mining practice. Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts ate needed.

Jan 1, 2001

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Ding Xu Chu

There are many methods developed for measuring the crustal stress in China. Among them only two methods have been adopted in practice, i.e., overcoring method (for which the sensors include: Piezo-magnetic stress gauge, steel-ring strain cell, 3-dimensional hollow-inclusion stress ,gauge, and Leeman's-like stress gauge) and hydraulic fracturing method. For the former method, one of those sensors is installed in a borehole, 36 mm in diameter, then prestressed, and finally overcored with a drill bit of 130 mm in diameter. After that the deformation of the borehole wall is measured, from which the in-situ stresses are determined. In order to avoid the errors resulting from the difference in elastic modulus for various kinds of rocks as well as from the installment of the cells, we have developed a technique to calibrate the sensor on-spot using a confining pressure calibrator and produced a very good result. For the later method, the measurements are achieved by isolating a certain section of a borehole and then injecting water to pressurize it till a tensile break is induced. It is identical to the typical technology used internationally. For many years, through field observations and a large number of laboratory experiments, we believe that the most efficient way of stress measurement for engineering purposes is the overcoring method using Piezo-magnetic stress gauge. It is characterized by stable and reliable measurement values, high accuracy and high adaptability. Taking the measurements in the intact rock mass as an example, the measured stress magnitudes are within accuracies of 8% and the errors in orientation are about 5 degrees. It can even be used perfectly in deep water. Up to now, we have performed in-situ stress measurements in more than 70 sites and obtain more than one thousand sets of data. The deepest depth used in the overcoring method is 80 m in vertical borehole and 780 m in tunnels.

Jan 1, 1987

The objective of extensive underground experimentation on three longwall coal faces was to improve the stability of mechanised longwall faces through investigation of the relations between support resistance and convergence and resultant deformation of roof and face strata. In particular the influence of high setting and yield pressures on several strata and support parameters was studied in great depth. Increased setting pressures resulting in an increase in setting load densities from 0.15 MN/m2 to O.45 MN/m2 were shown to reduce convergence, face spalling roof flaking, lateral movement of roof and floor, extrusion of the face wall and progressive failure of the coal wall ahead of the face. This was shown to result mainly from the change in roof strata deformation from a wedge shaped compression zone with tension at the face edge to an even beam shaped compression zone over the face area. Debris thickness above the support canopy and below the base was observed to be the one of the most variable parameters which influenced the support characteristics particularly the rate of load acceptance by supports and the roof to floor convergence. A setting load density of 0.4 MN/m2 to 0.5 MN/m2 was found to be optimum under soft to moderately strong sandstone roofs. The authors demonstrated that use of guaranteed set valves with powered supports contribute to good strata control, reduce face down-time and increase face productivity.

Jan 1, 1984