Search Documents

By Christopher J. Bise

It is somewhat reassuring to note that the United States has an abundance of coal reserves which can be used to bridge the widening gap between the nation's energy production and consumption. The U. S. Bureau of Mines has recently established a demonstrated coal reserve base of 434 billion tons. (31)(Figure 1) As can be observed, the major percentage of the reserves is in the West. Although surface coal mining in the West has been gaining increased attention in recent years, western reserves that must be deep mined are significantly greater. Though deep mining activity in the west is very limited and accounts for less than 2% of the annual production, the primary reason, quite probably, is the greater thickness of the seams as compared to those found in the East. Forty-five billion tons of the western demonstrated coal reserve base for underground mining are in seams greater than 10 ft. in thickness. (37) Thick coal seams do not lend themselves readily to extraction with the underground mining methods practiced in the United States today. Experiences from the practices in other countries can serve only as guidelines. Consequently, a concerted effort is necessary to overcome the technical difficulties.

Jan 1, 1975

By Robert W. Roscoe

For over a century, St. Joe Minerals Corporation in Southeast Missouri has been sinking shafts for their lead mining operations. Upon discovery of the Viburnum Trend, or "New Lead Belt", St. Joe brought its experience and expertise in shaft sinking to the area. Eleven shafts were then sunk in an 18 year period, ending in 1972. In 1981, St. Joe began sinking a new shaft in the Trend with hand-picked employees from the four operating lead mines and service facilities. The paper describes the general history of St. Joe shaft sinking methods and equipment, focusing on the current development of the Viburnum No. 35 Shaft.

Jan 1, 1983

By F. C. Townsend

Centrifugal modeling was used to evaluate reclamation schemes of; (a) flocculants, (b) sand/clay mixes, (c) flocculants/sand addition and (d) capping with sand or sand/clay mix. Results suggest the hierarchy of effectiveness is: (d) capping, (b) s/c mixes, (c) flocculants/sand addition and (a) flocculants. Comparisions between currently used large strain consolidation computer programs reveal no difference between piecewise linear or finite strain calculations. Correlations between numerical and centrifugal model predictions reveal excellent agreement on magnitudes; however, rate predictions require improvement in laboratory input data and centrifugal scaling relationships.

Jan 1, 1987

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today's gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1982

By C. L. Lin

Linear grade distribution measurements determined from polished sections of randomly oriented particles can be used to estimate the extent of liberation for multiphase particles of specified size. Two techniques, optical image analysis and microprobe analysis, have been used to establish linear grade distributions. Both techniques were evaluated and compared using variable grade samples of products from a copper porphyry flotation circuit. The statistical significance of the linear grade distribution data obtained by optical image analysis was assessed. The average chalcopyrite content of these samples, as determined by chemical assay was used to estimate the variance of the experimental procedure. For a given accuracy, the number of particles required to obtain an unbiased representation of the sample was determined.

Jan 1, 1985

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By W. P. Barnett

In 1988, the U.S. Department of Energy's Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation, and advanced cycloning. Each technology relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. Research projects designed to expeditiously develop each of these technologies to the point of commercial viability were initiated. This paper will present the status of these projects and the application potential of each technology to coal beneficiation.

Jan 1, 1992

By R. K. Mehta

An electrochemical coal oxidation model involving heterogeneous kinetics is presented. This model was tested by collecting current transient data on three coals assaying different ash content under varying operating conditions such as particle size, temperature, and % solids. In all cases, the model fitted the data very satisfactorily. Three intrinsic rate constants, namely mass transfer coefficient of Fe(II) Ions diffusing from solution to the anode (kma), mass transfer coefficient of Fe(II) Ions diffusing from solution to the coal surface (kmc), and chemical rate constant for coal oxidation with respect to Fe(III) at coal surface (k), were calculated. It was interesting to note that in this system, the mass transfer at anode was as important as the chemical reaction at the coal surface. The validity of this model was further demonstrated through a comparison of the activation energy of coal oxidation: firstly, by utilizing calculated chemical rate constant and assuming Arrhenius' type of relationship: secondly, by utilizing conventional approach using limiting current values. The comparison revealed that agreement was quite close. This kinetic analysis is useful because such a model can be used in predicting the intrinsic rate constants so that the relative importance of mass transport can be rationally analyzed.

Jan 1, 1991

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By W. J. Dolinar

The U.S. Bureau of Mines implemented the Fe2+ /Fe3+-SO2 anode reaction in a Cu electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/m2 (24 A/ft2) and 40 'C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb) compared to conventional electrowinning. Acid misting was completely eliminated, and SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1995

By A.M. Wala

A new radioactive tracer method to measure airflow in inaccessible airways has been developed for situations when studies of the mine ventilation system are not possible using conventional flowmeters (anemometers). The new method has been tested in the ventilation laboratory at the University of Kentucky and in the Experimental Underground Coal Mine at the U.S. Bureau of Mines. This new tracer method has been utilized in leakage, dilution and flow velocity measurements in laboratory and field (mine) experiments.

Jan 1, 1996

By Alireza Ayoubian, Richard Finno

The network of freight tunnels in Chicago consists of about 62 miles of horseshoeshaped tunnels constructed typically less than 50 feet below ground surface. These tunnels serve as repositories of much infrastructure and should remain serviceable. The tunnels are often impacted by adjacent excavations and the question arises as to the existing state of stress in the final liner. This paper discusses construction of these tunnels and presents the results of finite element analyses which were used to obtain ranges for axial forces and bending moments that have developed in the final liner of the freight tunnels since their construction.

Jun 13, 2023

By Earl M. Woodward

INTRODUCTION Kerckhoff-2 is a 140 MW underground hydro-electric project designed and owned by Pacific Gas and Electric Company and constructed between May, 1980 and May, 1983 by Auburn Constructors. The project is located in the western foothills of the Central Sierra Nevada Mountains, about 30 miles northeast of Fresno, California, and develops the power potential of the lower San Joaquin River and its tributaries between the existing Kerckhoff and Millerton Lakes. The Kerckhoff-2 Project consists of project roads, adits, and access tunnels, service tunnels, power tunnels, powerhouse, tailrace tunnel surge shaft, buss shaft, intake structure, discharge structure, and switchyard. In the 1920s, the Kerckhoff 1 project, consisting of a dam, reservior, tunnel, and 34 MW powerhouse, was built in the same general area as Kerckhoff-2. The tunnel was constructed by conventional methods, and was left unlined. In time, other projects were built upstream, allowing the flow of the San Joaquin River to be regulated. The Kerckhoff 2 project is designed to harness that regulated flow, providing an additional 140,000 ON of power. Kerckhoff 2 will be the primary power plant; Kerckhoff I will produce power whenever the flow rate exceeds 4,800 cubic feet. The new power tunnel is built along the east side of the San Joaquin River between Kerckhoff and Millerton Lakes, parallel to the existing tunnel but extending approximately one mile further downstream.

Jan 1, 1983

By Taeyong Lee, Cole Bales, Matt Fowler, John Horne

Mitchell Point Tunnel near Hood River, Oregon is one of the more unique segments of the Historic Columbia River Highway and State Trail being constructed through the Columbia River Gorge. This 650-foot bike/pedestrian tunnel set to open in 2024 is being delivered by FHWA in partnership with Oregon DOT, Oregon State Parks, and the U.S. Forest Service. Primarily driven using drill & blast excavation methods through basalt, the shotcrete and dowel-supported tunnel features masonry portals and ve window adits that provide illumination and views of the river similar to the original highway tunnel of many vistas built in 1915 that was removed in 1966 to make way for Interstate 84. This paper summarizes the planning, design, and construction.

Jun 23, 2024

By E. B. Jensen

The results of an extensive one- year test period of a nonelectric explosives detonating system led to the mine-wide adoption of this system at the Henderson Mine in early 1978. Since that time, extensive experience with nonelectric initiation has verified the earlier results which include the following benefits: 1. Increased blasting safety 2. Improved productivity 3. Cost effectiveness 4. High reliability At the present time, while electric blasting caps still experience a limited use restricted to trunkline initiation, all heading rounds as well as the longhole bell, undercut, boundary cutoff and raise blasting are detonated non-electrically. The primary blasting agent used is AN/FO, and primers are typically one of the following products (depending on application): PETN, semi-gelatin dynamites or a nonnitroglycerin water-gel slurry.

Jan 1, 1982

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By Richard M. Winar

In September of 1988, the United States Environmental Protection Agency (US EPA) published final regulations that effect owners and operators of underground storage tanks (USTs). These regulation include stringent technical requirements for owners and operators of USTs containing petroleum and certain hazardous substances. The technical requirements effect both new (those installed after December 1988) and existing USTs and include notification; performance and operating standards; release detection, reporting, investigation; release response and corrective action; and closure requirements for out-of-service USTs. The USEPA also published final regulations regarding financial responsibility requirements for owners or operators of petroleum USTs in October of 1988. These regulations require owners or operators of petroleum USTs to demonstrate financial responsibility for the costs of corrective action and compensating third parties for bodily injury or property damage caused by releases from petroleum USTs. Like thousands of other industries, the mining industry must become thoroughly familiar with these new regulations in order to properly manage their UST systems, ensure compliance, and understand other ramifications imposed by these regulations.

Jan 1, 1990