Search Documents

By George A. Savanick

Borehole (slurry) mining, in which a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a Bureau of Mines program to increase the domestic availability of critical minerals. Approximately 1700 tons (1.54x106 kg) of phosphate ore were mined at 40 tph (10.1 kg/s) from a depth of 250 ft (76 m). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1983

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By Richard S. Della Valle

Sandstone and shale samples from the Morrison (Late Jurassic) and Dakota formations (Cretaceous) from northwestern New Mexico have been analyzed for the major elements Na, K, Fe and the trace elements Sc, Cr, Co, Rb, Sb, Cs, Ba, Hf, Ta, Th, iJ and the rare earth elements (REE) in whole rock and clay sized fractions by instrumental and delayed neutron activation analysis. The clay sized fraction clearly shows enrichment patterns and halo effects ; whereas, the whole rock fraction does not. Important elemental dispersion halos associated with uranium in sedimentary environments include the REE, Hf, and Sb. The distribution of these halos are due to a combination of complexation, chelation and the orignal paleoenvironments.

Jan 1, 1984

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By Robin P. Gardner

The development and use of short-lived radioactive tracer methods for the on-stream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a-large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1978

By Paavo Eerola

In May of 1984, it was decided that Outokumpu Oy would design and build a new nickel flotation mill to process ore from the newly discovered Enonkoski mine in eastern Finland. Since there hart peen a number of successful process charges in the existing mills, the design effort included the study and incorporation of several new developments, including all-autogenous grinding, "flash flotation", lane cell roughing, large cell cleaning and a computer-based, profit optimizing, process control system. The paper discusses the background and results of those studies, and a description of the resulting mill which will begin production in 1986.

Jan 1, 1985

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By Manfred Jaeger, Klaus Ertmer, Walter Dietrich, Jochen Greinacher, Wilhelm J. Kogelmann

In Europe, novel low-cost excavator-mounted Multi Tool Miner (MTM) systems, consisting of cutter head, hammer, bucket and drill attachments permit one unit to perform multiple tasks replacing several purpose-built machines. At the Weser Tunnel in Germany, cross-passages between the twin tubes were excavated in frozen ground with a remote-controlled mini-excavator equipped with a quick-change cutter head, ripper tooth and bucket. In Switzerland at the N2 interstate near Basel, W. Dietrich AG enlarged a 2-lane tunnel to three lanes with a cutter head mounted on a special excavator. Blasting and heavy hammers were not permitted due to the closeness of the “live” twin tube. At the N20 Zurich bypass, the Joint Venture of Jaeger, Frutingerand AHB excavates highway tunnels, some with extremely large cross sections, conventionally. A cutter head mounted on an excavator removes the rock shattered by blasting precisely to the pay line, thus preserving the rock’s self-supporting capacity preventing subsidence and damages to water resources and buildings on the surface under low overburden.

Jan 1, 2003

By Wang Zuoyu

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies to the time of the Symposium.

Jan 1, 1986

By I. H. Warren, F. A. Forward, D. E. Pickett, Ernest Peters, Alvin H. Ross, I. M. Masters, N. P. Finkelstein, R. Derry, A. W. Fletcher

In this section the chemical, physical, and mechanical principles of hydrometallurgical processes are developed and reviewed. Plant practice is not discussed other than to note the metals which are processed using the various systems that are available. These notations will permit the reader to refer to the appropriate section in Part II of the Handbook for specific details on a particular metal or mineral. The equipment used to accomplish the desired unit operation is de¬scribed. Comparative data are presented to illustrate performance characteristics of unit operations, process, and equipment. The economic efficiency of individual processes is outlined. Some of the chapters contain material that is covered in detail in other sections of the Handbook Such chapters are developed only sufficiently to indicate the specific application of the techniques to hydrometallurgical processes. In this section considerable cross-referencing to the other related sections has been done.

Jan 1, 1985

By D. A. Norrgran

The process of magnetic separation is based on the differences among magnetic susceptibilities of various mineral species. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents from a product stream. There are two major catagories to be considered when addressing magnetic separation of minerals. The first catagory refers to particle characterization and relative differences in magnetic susceptibility. The second catagory refers to design parameters and the magnetic field generated by the separator.

Jan 1, 1987

By S. Acar

"In recent years the gold mining industry has been challenged by declining metal prices as well as having to treat ores that have low grades and are refractory in nature. Many factors must be considered when metallurgical studies are designed to develop process design criteria for these type of ores. These factors are mostly related to the mineralogical and chemical compositions of the ores, the geological setting of the deposit and how the ore/waste will be mined, such as whether openpit or underground, the mine schedule, and the mine fleet type and capacity. The purpose of this paper is to provide an experience-based practical approach to how to select and characterize test samples as well as devise process development metallurgical studies for both oxide and refractory gold ores, and to provide insight into some of the matters that might go wrong during the course of the studies. This paper is intended as both a guide for someone new to the field and also as a reminder for those familiar with the field. IntroductionThe recent decline in ore grades and metal prices have challenged mining companies to reduce capital and operating costs associated with developing new mineral resources. In some cases, metallurgical studies have been sacrificed to prevent cost overruns resulting in inadequate mineralogical, chemical and metallurgical characterization. Consequences have included longer construction schedules, higher initial and working capital, higher operating costs and less than desirable plant performance (Whincup, 2010; Torres, Chaves and Meech, 1999).Mineralogy, geology, mining type and sequence, and the metallurgy of an orebody will determine the process development metallurgical study requirements and eventual process plant design. Therefore, once the geologist has an early indication of a prospective orebody, geologists, metallurgists, mining engineers, and social and environmental responsibility scientists should convene and devise a plan on how to exploit the orebody economically (Lunt, Ritchie and Fleay, 1997).Geologists may find a prospective orebody solely based on grade. However, if the orebody cannot be mined and processed economically, then it is deemed not to be a deposit. An example of this could be a refractory gold deposit, either sulfidic, carbonaceous or siliceous refractory or any combination of those, that may not be mined and processed economically due to reasons such as the physical location of the deposit, depth of the ore lode, or social and environmental concerns. Therefore, an early collaboration between all disciplines must be established.Each orebody may have its own unique mineralogical, geological and chemical characteristics (Guresin et al., 2012). These unique characteristics should be effectively sampled to reduce risks associated with process design and engineering efforts for the process development metallurgical studies. If the sample or samples are not representative of these unique characteristics, then the studies performed will be pointless. The project metallurgist in charge of conducting metallurgical studies should also possess general geology, mineralogy and mine engineering knowledge. Recommended readings are a book on understanding mineral deposits by Misra (2000) and articles on heap leach development by Scheffel (2014a and 2014b)."

Jan 1, 2016

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Jan 1, 1997

By A. M. Raichur

The selective adhesion of hydrophobic Mycobacterium phlei to coal particles is responsible for flocculation of fine coal from associated ash forming minerals. The driving force for the differential adhesion is the hydrophobic interactions between the fatty acid surface of the organism and hydrophobic nature of coal. The effect of Mycobacterium phlei on surface hydrophobicity, surface charge and mechanism of adhesion on coal and associated minerals are controlled by several factors including hydrophobicity and surface and solution chemistry of the system. Adhesion measurements indicate that maximum adhesion occurs below the isoelectric point (IEP) of the coal particles. While massive adhesion of Mycobacterium phlei is observed on coal, however, negligible amount of Mycobacterium phlei attaches to mineral pyrite and quartz.

Jan 1, 1995

By Adam Bedell, Paul Derby, Brad Crenshaw

Modified contact grouting was introduced almost 15 years ago as a methodology combining traditional contact grouting and consolidation grouting to address groundwater infiltration into hard rock tunnels that utilize cast-in-place concrete as permanent tunnel support. This process has been used on additional tunnels (since initially presented) as a measure to mitigate both groundwater infiltration and exfiltration. During this time, self-sealing grouts have been developed and have been added to the process to further reduce groundwater infiltration that occurs through cracks and discontinuities within the concrete liner itself. This modification is presented and additional results from the grouting process are discussed.

Jun 13, 2021

By G. V. Sullivan

As part of its program to conserve domestic mineral resources through advancing mineral resources technology, the U.S. Department of the Interior, Bureau of Mines, conducted investigations to determine the feasibility of recovering high-grade barite concentrates, suitable for use as well-drilling mud, from current and old waste pond materials and materials bypassed in present mining operations. Flotation studies of waste pond samples from Missouri and Nevada yielded barite concentrates containing over 95 percent BaSO4 with recoveries of 86 percent and 96 percent, respectively, of the barite in the flotation feed. Flotation studies of a hard-rock sample from Georgia, currently bypassed in mining, yielded a barite concentrate containing 97 percent BaSO4 with an attendant recovery of 97 percent of the barite.

Jan 1, 1980

By T. C. Page

The Yarnell gold depoSit, located in the Weaver mining district of Yavapai County, Arizona is found within a structurally controlled, hydrothermally altered zone that occurs within a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rock that occur around and above the low-angle northeast striking Yarnell fault are known to host economic gold mineralization; a wider envelope of weakly-propylitic alterred rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz ± adularia veining, stockwork formation, and localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized), and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit although the thickness of the zone and associated alteration envelope diminish away from the orebody. A sample of undeformed illite taken from the Yarnell fault zone was K/Ar dated at 69 ± 1.6 Ma; this date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As, Cu, and Mo content. Both CO2-and H20-rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit.

Jan 1, 1992

By K. E. Harrison

The acid rain legislation has passed into law. This new law has caused the power generation community to investigate alternative methods to obtain compliance with the new legislation. One thing all of the power companies have concluded is the answer is not easy. Do we switch fuels to burn all low sulfur compliance coal? Maybe possibly only partial desulfurization by means of a dry sorbent system? Or, finally, maybe a wet scrubber system? Whatever the choice, the power community needs to investigate all of the alternatives. In 1988, ICF Kaiser Engineers, Inc. (ICF KE) responded to a request by the U.S. Department of Energy for the engineering development of advanced physical fine coal cleaning. ICF KE responded and was awarded a contract to conduct a multi-task program to develop an advanced flotation system to eliminate pyritic sulfur and retain as much energy as possible. ICF KE assembled a team that included members of industry, academia, and industry research organizations to conduct this multi-task program. The program includes sixteen (16) tasks. This team had personnel to help solve some of the anticipated problems and to provide industry prospective on the viability and commercial potential for any concepts proposed. The primary team consists of a major coal producer, Babcock and Wilcox, Eimco Process Equipment Company, and Virginia Polytechnic Institute and State University.

Jan 1, 1992