Search Documents

By C. L. Jiang

The selective depression of pyrite obtained from Kentucky No.9 seam in coal flotation with various kinds of inorganic and organic chemicals was systematically examined. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates has been explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta potential measurements. It was shown that pyrophosphate reacts strongly with iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1998

By Gary Peach, Peter Mason

Planning and estimating progress rates and costs for tunnelling is always best done based on experience and historic precedent. Much precedent is available but the use of data monitoring, data mining and other retrieval techniques on modern TBM machines can enable this to be further expanded and refined. Advance rates can be related much more closely to rock types as can associated rock bolt and mesh/ shotcrete requirements. This in turn can lead to a further refinement in best likely combinations of equipment, such as shotcrete jumbos, better selected for the anticipated conditions, rather than the potential advance rates of the machine. Efficient and timely construction of the tunnel will also be linked to times needed for finishing work, such as contact and void grouting and to how this can be initiated while the TBM is still in operation, in order to save overall construction time. Indeed, this in turn may affect the most preferable layout and construction details of the permanent tunnel. Considerable experience has been gained in the use of two large diameter TBM tunnel drives through the Himalayas at the Neelum-Jhelum hydropower project in Pakistan. All the above aspects will be discussed in the paper based on the considerable experience and data which came from that operation, including appropriate measures in highly stressed areas potentially subject to rock burst.

Jun 13, 2021

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By Martin B. Zimmerman

It is becoming evident that traditional methods of econometric analysis are inadequate in estimating-the long-run supply of minerals. Econometrics is limited to extracting estimates from observations of the theory predicts that the least cost deposits will be exploited first.1 The estimation of parameters from past data then must lead to biased projections of the future. Mining conditions in the future will be worse than in the past and it is the impact of the future conditions on cost that we need to know. In this paper we present a methodology for dealing with this problem. We estimate a "cumulative cost" function that yields the long-run marginal cost of mining as a function of cumulative output produced over time.2 This is relatively easy to do for coal mining in the United States where exploration for new deposits is not a major factor in supply. The first step of the procedure relates cost to the rate of output and to the geological conditions of the mine. The second step combines geological information on remaining deposits with the cost function to yield the cumulative cost function. A central theme of both these steps is the interaction of economics with geology. The best deposits are selected first and in each step of the estimation allowance must be made for this fact. The problem of depletion is part of the general problem of structural change. The change through depletion in the nature of the exploitable mineral stock is only one factor that calls for an analysis sensitive to the changing circumstances of the industry. The factors impinging most heavily on the coal industry today are the strict environmental regulations legislated

Jan 1, 1977

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By J. H. Gasper

A cost analysis for two alternative contour mining methods is performed to compare their results. The methods evaluated are: 1) Front-End Loader/Truck Haulback and 2) Scraper Haulback. Before performing these analyses, output requirements and equipment needs are found based on integrating geometric limitations with material properties. The final geometric design establishes limits on clearances, congestion problems and grades (with associated running surface materials). All calculations are kept practical, with assumptions clearly stated. The cost analysis is a unique, easily utilized compilation of several different approaches incorporating cost engineering principles. The strengths of each are welded into a cohesive entity once again aimed at practical application. The results are presented in tabular form.

Jan 1, 1992

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By R. M. Rowe, T. E. Irwin

A flowsheet was developed for upgrading Climax tin concentrate to about 45 percent Sn. Bench-scale test work conducted at AMAX Extractive Research and Development, Inc., was used to design a multiple-stage tin- processing flowsheet which included screening, high-intensity magnetic separation, and high- tension (electric- static) separation. Formal engineering and plant installation was accomplished in-house by Climax mill personnel. The successful start-up operation of the facility was the joint effort of the AMAX R&D and Climax-mill staffs.

Jan 1, 1986

By B. P. Bellport

This paper summarizes the Bureau of Reclamation's experience in the use of boring machines to excavate six major tunnels on the Bureau's water resources development projects in the western United States. The summary of experience is presented as a compilation of brief case studies for each of the six tunnels. Each compilation presents data on the tunnel dimensions, geological characteristics of the excavated rock, the tunneling machine used, machine operation, muck handling, method of tunnel support, ventilation system, and related information. The listing of the six tunnels in Table 1 reflects a diversity of tunnel lengths and diameters. However, despite this diversity of dimensions as well as the variety of rock encountered during excavation, the six tunnels have one major characteristic in common: their excavation was significantly expedited by the use of boring machines. Beginning with the 10,079-foot-long Tunnel No. 1 on the Navajo Indian Irrigation Project in New Mexico - the Bureau's first tunnel to be excavated by a boring machine - the boring machines, or "moles," have demonstrated their effectiveness in rapid and economical tunnel excavation. Tunnel No. 1, virtually 2 miles long, was bored through in 9 months, an unprecedented achievement in Bureau engineering experience, as compared with tunnels previously excavated by conventional means. Boring of the 45,630-foot-long Blanco Tunnel and the 26,610-foot-long Oso Tunnel, both on the San Juan-Chama Project in Colorado, set world records in rates of excavation,l/* Two days of exceptional progress highlighted the

Jan 1, 1970

Application of flotation for the removal of hydrophobic compounds from soils was studied. Bench scale flotation tests were conducted on artificially contaminated soil, using both conventional mechanically agitated machine and flotation column. Flotation parameters tested include surfactant collector type, conditioning time, flotation time, surfactant dosage, pulp pH, solid/liquid ratio in conditioning and pulp temperature. It is found that with conventional flotation 74% removal of the contaminant was achieved from soil particles in the range of 75-830 µm; with column flotation up to 80% of oil could be removed from the 250-830 µm soil fraction, and 65% from the 75-830 µm fraction. Flotation was found to have considerable potential for cleaning up contaminated soils.

Jan 1, 1998

By R. Gilges

The implementation of effective techniques for meeting the maintenance requirements of the new Utah Copper Division smelter, one of the largest in the Western Hemisphere, is a goal of the smelter management and supervisory personnel. Kennecott's Metal Mining Division Computing Center has been working with smelter personnel to implement a computer program to provide instantaneous access to equipment specifications, maintenance and cost histories, spare parts, preventive maintenance scheddes, etc. for several hundred pieces of equipment. This information will be available to all smelter personnel via visual display terminals. The system will dramatically reduce the time now spent in search of pertinent information required in effectively performing the maintenance functions. It will also be used to analyze practices, detect trends, prepare budgets, and substantially reduce the paper work normally associated with the running of a large and complex maintenance organization.

Jan 1, 1977

By Rodrigo Estay Huidobro, Andrés Martinoli, Claudia Pavez-Orrego

The effects of induced seismicity caused by mining activities are one of the main problems that the mining industry faces. Although it has been documented by countries with a great mining tradition (United States, Canada, Australia and Chile) for over a century, the problem has been intensified throughout the years due to the greater depths that mineral extraction reaches, where the stress levels and environmental conditions increase the possibility of a rockburst occurrence. Seismic events inside the mine cause important losses of human lives and infrastructure damage. To deal with this problem it is necessary to implement several kinds of safety protocols. For example, seismic indicators allow to identify, through the analysis of a set of seismic parameters -magnitude, energy, time, decay rate, among others-, periods of time when a seismic event of considerable magnitude is most likely to occur. The objective of this work is to use the frictional energy generated by a microearthquake inside the mine as a seismic indicator, linking it with the occurrence of large magnitude seismic events which are outer the background activity. Thus, we seek to determine the set of seismic parameters which allow the best performance of the frictional energy/heat indicator. In the present study, we considered magnitude, frictional energy, and time as seismic parameters to study the efficiency of the proposed indicator. The optimal set of parameters was determined using two different methodologies: accumulated thermal energy and alert bands. The Piece Skill Score and the Accuracy indexes were used to evaluate each set of parameters. Both approaches show a high rate of true positive and true negative hits. Furthermore, it was concluded that both methods show complementary results in terms of the detection of critical events (Mw > 3.0).

Apr 26, 2022

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By T. Yue, Z. Gao, X. Tong, R. Liu

"Lead ions (lead nitrate) were introduced to modify the surface properties of scheelite, effectively and selectively improving the flotability of scheelite, with benzohydroxamic acid (BHA) serving as the collector. A series of experiments about the mode of addition and the ratio of lead ion to BHA were conducted and indicated Pb-BHA complexes were the active species responsible for the flotation. And two adsorption models of BHA on the surface of scheelite were established. For both the two adding methods, some kind of complexes formed by lead ions and BHA played a key role in the flotation process. Zeta potential, FTIR, and XPS studies indicated that the adsorption amount and intensity of BHA on the surface of scheetlie were larger by adding the reagents as a mixture. The mixed addition is conducive to form Pb-BHA complexes and improve the adsorption efficiency of BHA on the surface of scheelite, as well as the recovery of scheelite. INTRODUCTION Scheelite, as an important tungsten-bearing mineral, is nowadays utilized mainly by flotation (YIN and WANG, 2014; Sun et al., 2011; Gao et al., 2015; Gao et al., 2015). Flotation separation of scheelite from calcium minerals creates difficulties because of the existence of the same cation in the minerals and similar physico-chemical characteristics such as solubility, hardness, specific gravity, point of zero charge (PZC), etc. (Arnold and Warren, 1974; Deng et al., 2016; Deng et al., 2015; Ozcan and Bulutcu, 1993a; Yongxin and Changgen, 1983). The conventional collectors used in the flotation of scheelite ores are generally fatty acids or fatty acid derivatives (Bo et al., 2015; Oliveira and Sampaio, 1988; Shi et al., 2014; Sivamohan, 1988; Yongxin and Changgen, 1983). It is difficult to separate scheelite, especially from calcite, with these reagents because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface (Atademir et al., 1979; Changgen and Yongxin, 1983; Hiçyìlmaz et al., 1993; Hu et al., 2011). Therefore, it is almost impossible to separate them by fatty acid flotation without using any selective depressant. Although oleoyl sarcosine was used as a selective collector in the flotation of fluorite and siliceous scheelite ores (Ozcan and Bulutcu, 1993b; Ozcan et al., 1994), this selectivity is inadequate for a low-grade calcitic scheelite ore. Unfortunately, reagents such as organic colloids (dextrine, starch), quebracho, sodium phosphates, sodium silicate solutions containing polyvalent cations (hydrosols), etc. (Bo et al., 2015; Schubert et al., 1990; Shi et al., 2014; Yongxin and Changgen, 1983), used for calcite depression also depress scheelite to a large extent. Cationic collectors, such as amine and quarternary ammonium (Yang et al., 2015) and collector mixture (Gao et al., 2015) have been used to improve the scheelite flotation. However they have not been applied in industry due to the poor separation from silicate minerals."

Jan 1, 2017

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By Todd Burchett

Mining engineers spend countless hours and resources when designing a new underground coal mine. Their primary objective is to design the safest and most efficient operating mine with regards to coal production. A key variable often overlooked in this design stage is the slope conveyor. Typically, a slope conveyor is expected to operate with a 98-percent or higher availability. However, too often little effort is put forth by the mining engineer to optimize its design. Coal companies will rely on engineering, procurement, construction and management (EPCM) companies for the preliminary design, because the slope conveyor will be considered part of the surface material handling processes. This preliminary design will be used when soliciting quotations for the slope conveyor. Unfortunately, EPCMs may not have enough expertise with conveyors to optimize the design. This expertise is available with an original equipment manufacture (OEM) of conveyors, which ultimately may be responsible for supplying the slope conveyor. Each OEM will provide a bid package that represents what it considers to be the optimal design.

Jan 1, 2013

By Akira Ishikuro, Masamichi Shintaku, Futoshi Kusumoto, Takeshi Kudo

"The Bankei-Kitanosawa tunnel that is located in Sapporo, Hokkaido, Japan includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. The mucks containing hazardous materials were disposed into the waterproof branch tunnels created from the inside of the main tunnel. The full face early ring closure method was employed to ensure the stability of the tunnel in the low strength rock masses having no stand-up time. As a result, the waterproof tunnels branching off the main tunnel can manage water tightness so as to ensure safety and relief against environmental risks of the hazardous materials. It is also demonstrated that the full face early ring closure method enable construction of the tunnel with a small overburden in the low strength rock masses. INTRODUCTION The Bankei-Kitanosawa tunnel includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. In order to overcome the restrictions, the hazardous materials were designed to be disposed into large cross section waterproof tunnels which were newly designed and constructed in high strength and hazardous material free Andesite. The lining for the tunnels was composed of with shotcrete. In addition, full face early ring closure (Sato et al., 2013) was employed to stabilize the tunnel so as to enable safe tunnel excavation in low strength rock masses where a ground arch is deemed unachievable. This paper presents the safe disposal method of mucks which are likely to liquate out natural hazardous materials as well as the full face early ring closure method and its mechanical characteristics."

Jan 1, 2016

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By M. D. Flavel

My paper relates to bond's third theory of comminution and suggests work be used as a basis for designing crushing and screening plants, this will give more accuracy than existing methods, As stated in the abstract, this paper is only a synopsis of my official paper, many of the questions that might arise in this brief address will be answered by referring to the detail i n the main paper $ Because of the limited time available and the fact that many people here do not need to study the aspects of crushing and screening in depth, i will highlight-those sections of the paper which show how major capital, operating and energy cost savings can be achieved in the process, I will develop the theme in the following manner, Firstly, pointing out, why a new approach is needed to the fundamentals of crushing and screening, Secondly, by setting forth some theory to describe what we are trying to accomplish, Thirdly, by looking at important factors which need to be observed in designing plants and applying machines to comply with this theory, Lastly, i will put forth some ideas on how we might develop this theory to make the industry more efficient, At the outset, i have to say my approach to this process is entirely new, for those used to applying machines and designing plants on existing criteria, they will find this theory easier

Jan 1, 1977