Search Documents

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By Deepak Malhotra, Linda Battich

INTRODUCTION Mineral processing plants generally operate efficiently within the technical, economic and management constraints applied to them. They have no choice, because the dynamic and competitive nature of the mineral business dictates that survival and/or prosperity of the company depends on being a low cost producer. Progressive mineral companies realize that market downturns will occur, and they must continuously strive for lower unit production costs rather than be satisfied with the status quo. Mineral companies generally tend to reduce costs during market downturns. This short-term solution is achieved by high grading of ores, and cut-backs In waste stripping, exploration, and capital expenditures.(1) However, to remain a low-cost producer in the long term, companies must enhance revenue and reduce cost simultaneously. This Involves continuous evaluation of technologies and reagents, periodic audits to locate revenue losses; and gathering and analyzing statistical plant data to clearly understand the Impact of process variables on efficiency. Mineral companies are caught in a Catch-22. They need resources to accomplish the objectives outlined above. Most mill stuffs have been cut to the minimum level necessary to maintain production. Resources such as time, manpower and money are scarce, and mill metallurglsts struggle to use these resources productively. Is your flotation plant optimized? History Indicates that successful operations constantly tune the flotation circuits to Improve metallurgy or reduce cost. This Is the essence of evolutionary change In mineral processing operations. A plant auditing approach can play a key role in assisting the process engineers to achieve the overall objective of enhancing metallurgy and reducing cost with limited resources through evolutionary improvements. FLOTATION SYSTEM The flotation process is the most widely wed concentration process In the world today. The number of variables that can affect the flotation results Is very large, maybe over 100. These variables can be divided Into three main groups: (2) (1) ore and mineral properties; (2) reagent treatment; and (3) flotation machine characteristics. Some of these variables can be controlled while others have to be accepted. Recently, Investigators (3,4) have attempted to describe the flotation process as an engineering system which includes chemistry, equipment and operating variables. Though some of the variables are Independent, most are co-dependent. thus making it difficult to develop simple cause and effect relationships. For example, it is easy to understand the effect of reagent change on recovery and grade In the rougher circuit, but very difficult to quantify Its impact on filtration downstream. Plant audits on a periodic basis are necessary to develop an understanding of the Interactive nature of the system. Auditing provides comparisons of plant operating performance before and after variable changes. OVERVIEW OF PLANT AUDITING An audit Is a formal, thorough and periodic examination of a system. There are various types of audits (i.e., geological, environmental, metallurgical. economic, etc.), and each serves a different purpose. (5) The discussion here is related to plant and/or metallurgical audits. Neale and Flintoff note that two key factors governing changes In an operation are: (1) the opportunity must be recognized; and (2) the justification for change must exist. (6) Both factors emphasize the critical role of successful plant auditing. Without plant audits. many opportunities for improvement must go unrecognized. On the other hand, when a situation ripe for improvement Is recognized. the hard data from a plant audit can reveal the expected impact of an operating change.

Jan 1, 1993

By Eivind B. Jensen

Introduction Though temporarily shutdown due to the depressed economy, the Henderson mine is a large underground molybdenite producer, using a continuous panel-caving mining system. The location of the ore body requires access from the surface through three shafts, the collars of which are located about 3.15 km (10,350 ft) above sea level. At this altitude, normal temperatures are such that heat must be added to intake-ventilation air for about half of each year. This prevents ice from building up in the intake shafts, waterlines from freezing underground, employee discomfort, and equipment-related problems such as pneumatic rock drill icing and cold starting of diesel engines. Because of topographic and environmental constraints, the Henderson mill and concentrator are located 24 km (15 miles) from the mine, on the west side of the Continental Divide. All ore from the mine is transported to the mill by an electrified rail haulage system, with 15.4 km (9.6 miles) of the trip being underground through a double-track tunnel. A shaft at the midpoint of the tunnel exhausts air drawn from the mine and from the portal that is at an elevation of 2.7 km (8,950 ft). Intake air at the portal must be heated for part of the year to prevent ice buildup. Mine Ventilation System The mine ventilation system uses three sources of fresh air and two exhausts. The primary freshair intake is No. 3 shaft. It is concrete lined to a diameter of 7 m (23 ft) for a total depth of 698 m (2,291 ft). An airflow of 755 m3/s (1.6 mil¬lion cfm) is supplied to this shaft by two vane-axial 932-kW (1,250-hp) fans on the surface. The air is distributed within the mine by means of fresh-air distribution levels connected to production and development levels by raises. A secondary source of fresh air to the mine is provided by No. 2 shaft, the primary man and material access. This shaft is concrete lined to a diameter of 8.5 m (28 ft) for a total depth of 946 m (3,105 ft). Downcast airflow is induced by a pressure differential produced by the fans in the system such that net intake and exhaust volumes are equal. The No. 2 shaft flow of 165 m3/s (350,000 cfm) enters the mine network from the production and haulage levels. Exhaust air is moved from the various working levels through connecting raises to exhaust col¬lection levels that return it to No. 1 shaft. No. 1 shaft is the primary mine exhaust. It is concrete lined to a diameter of 7 m (23 ft) for a total depth of 788 m (2,584 ft). Three vane-axial 932-kW (1,250-hp) exhaust fans are located at the collar of No. 1 shaft, producing a flow of 850 m3/s (1.8 million cfm). In addition, an airflow of 71 m3/s (150,000 cfm) from the intake distribution level is exhausted via the haulage tunnel, by means of No. 4 shaft located midway in the tunnel. The main features of the mine ventilation network are summarized in Fig. 1. Ventilation Air-Heat Plants No. 3 Shaft In the early design phase of No. 3 shaft, it was recognized that air heating would be required to maintain underground temperatures above 0°C (32°F) during cold winters in the Colorado mountains. When the air reaches the mining

Jan 1, 1983

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

It is imperative that the hydrogeologic frame- work and the ground water flow systems of a Potential mine area be investigated prior to initiation of mining. Such investigations are necessary so that potential mine water inflow problems can be anticipated and controlled. Obvious difficulties can arise if large inflows of ground water occur in underground workings. Costs of water removal and disposal, if not foreseen and included in economic planning, can severely limit or eliminate profit from a mining operation. Safety problems associated with large inflows are an additional potential problem. The inflow of water into a mine necessarily alters the associated ground water system. The inflow also may impact nearby surface water regimes, depending upon the interaction of the surface water and ground water systems. The inflow of water into a mine inevitably causes a decline in the ground water levels in the vicinity of the mine. This decline may be restricted to a small area or it may extend a considerable distance, depending upon the hydrogeologic properties of the associated hydrostratigraphic units. A decrease in surface flow will result if the area of ground water level decline intersects a stream or spring that is hydraulically connected to the ground water system. Mine inflow problems historically have been evaluated after-the-fact. Premining hydrologic investigations only recently have been initiated. Brown's (1977)* report on anticipated hydrologic impacts of oil shale mining in the Piceance Basin of Colorado is an example of premining hydrologic planning. Observed difficulties inherent in designing a data collection network and then utilizing the data to predict mine inflow have led us to the preparation of this manuscript. This manuscript reflects a two-phase effort. The first phase describes and develops analytical and numerical techniques for mine inflow prediction. Emphasis in this section is placed on the selection and application of data collection techniques and data analysis procedures. The second phase applies the prediction technique(s) developed during phase 1 to two existing mines. The objective of phase 1 efforts is to evaluate the hydrologic variables associated with surface water systems and ground water systems that can affect the inflow of water into an underground mine. Subsequently these variables are incorporated into predictive techniques for estimating underground mine water inflow and its effect on associated ground water and surface water systems. The specific objectives of phases 1 and 2 are to: 1) Determine the hydrologic parameters required for predicting underground mine water in- flow and the potential effects of the inflow on surface and ground water systems. The hydrologic parameters represent both premining and past initiation conditions. 2) Outline methods for obtaining the necessary input data for the predictive techniques in pre- mining and post initiation periods. 3) Present existing numerical techniques for predicting underground mine water inflow including assumptions Ad required input. 4) Evaluate existing numerical techniques previously tabulated based on their applicability to mine water inflow prediction. 5) Attempt to develop analytical techniques for predicting underground mine water inflow. 6) Develop, through modification of existing models, a general mathematical model as a numerical technique for predicting underground mine water inflow and the resultant effects on surface and ground water systems. 7) Apply the predictive techniques to two existing mines selected for this purpose. 8) Compare the predicted inflow rates to measured inflow rates at both mines. 9) Compare predicted impact on district hydrology to observed impacts where possible. 10) Evaluate the predictive technique.

Jan 1, 1986

By D. W. Carson, R. J. Trembley

Thoron daughter WL&apos;s measured by alpha-spectroscopy and the Kusnetz method are about one-half those of radon daughter WL&apos;s in a uranium mine in Canada.1 A diffusion model can account for the relative concentrations.l Since the Kusnetz technique is most widely used for measuring radon daughter WL&apos;s in uranium mines, a general procedure is derived to extend this method to measurement of WL&apos;s of radon and thoron daughters in air containing their mixtures. Coté P. and Townsend M.G., 1981. A procedure is also suggested for counting radon and thoron daughters by 3-channel [a]-spectroscopy. Errors in WL(Rn) are calculated for standard radon daughter counting procedures when a-decay of both thoron and radon daughters is attributed to radon daughters alone. Providing overall counting times are short, [<]30 min, these errors are generally small. The precision of ß -counting methods is also investigated. A portable 3-channel alpha spectrometer for measurement of radon and thoron daughters in uranium mines or homes is described, Carson D.W., 1979. The computer programs for analyzing the data to give, depending on the mode employed, some or all of the concentrations RaA, RaB, RaC, ThB, ThC and WL of radon and thoron daughters by alpha spectrometric, modified Kusnetz, Rolle and Tsivolglov methods are presented.(l) A commercial apparatus, based on the above prototype, incorporating a microprocessor and built under contract to EMR is now available.(2) A number of personal radiation dosimeters for miners are now being tested in mines. One of these is the CEA dosimeter which uses the track-etch film method, Duport P., Chapuis A.M. and Pradel J., 1979. An apparatus for rapid reading of track-etch films by the spark technique has been described previously, Cross W.G. and Thomasino L., 1970 and Huang V.F., 1975. We have developed such an apparatus for rapid semi-automatic reading of films exposed to radiation from mixtures of radon and thoron daughters in CEA dosimeters. The films used, Kodak LR 115 Type II Strippable, may be stripped rapidly and easily, for counting after irradiation and developing, by use of a special punch and suction technique. The method promises to provide an inexpensive and rapid technique for reading large quantities of personal dosimeter films. However, the present CEA dosimeter has faults in design, leading to a contamination problem. Those films that show contamination cannot be read by automatic means. A commercial apparatus based on the above prototype spark counter and built under contract to EMR is now available.3 1. These computer programs are available on request. 2. Pylon Instruments, Ottawa 3. Bondar Clegg, Co. Ltd., Ottawa. REFERENCES Carson, D.W., 1979, "Canalph-3, a Portable Three-Channel Alpha-Spectrometer for Measuring the Daughter Products of Radon and Thoron", CANMET Division Report MRP/MSL 79-108 (TR). Coté, P. and Townsend, M.G., 1981, "Mixtures of Radon and Thoron Daughters in Underground Atmospheres", Health Physics, Vol. 40, pp 5-16. Cross, W.G. and Thomasino, L., 1970, "Rapid Reading Technique for Nuclear Particles Damage Tracks in Thin Foils", Radiation Effects, Vol. 15, pp 85-89. Duport, P., Chapuis, A.M. and Pradel, J., 1979, "Appareil Individuel pour lu Dosimetrie des Descendants du Radon", Advances in Radiation Protection Monitoring, IAEA Vienna, pp 435-443. Huang, Y.F., 1975, "Determination of Uranium in Minerals using Fission Tracks", M. Sc. Thesis, University of Toronto, 48 pp.

Jan 1, 1981

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By Jay S. Silhanek, Vernon E. Andrews

[Introduction] Section 122 of the Clean Air Act Amendments of 1977, Public Law 9595, directed the Administrator of the Environmental Protection Agency, to review all relevant information and determine whether emissions of radioactive pollutants into ambient air will cause or contribute to air pollution which may reasonably be anticipated to endanger public health. In August 1979, EPA published a preliminary report on assessments of public health impact resulting from emissions of radionuclides into air from a broad spectrum of major source categories (1). A section of this document presented a theoretical analysis of the radioactive airborne emissions from several non-uranium mines including iron, copper, zinc, clay, limestone, fluorspar, and phosphate. Since 1978 EPA&apos;s Las Vegas Laboratory has been gathering field data on actual radionuclide emissions from these mines to support the earlier theoretical analysis. The purpose of this paper is to present the results of those field measurements in comparison with the assumed values for the theoretical analysis. Data were presented in EPA&apos;s preliminary report on both gaseous radon-222 and particulate uranium-238 emissions from non-uranium mines. Most of the emissions data were rough estimates based upon the uranium content of the ore. Preliminary data from a few field studies were also used. Although both the theoretical and field studies by EPA were concerned with radon-222 and radioactive particulate emissions, this paper will concentrate only on the radon effluents. Radon from mines seems to have the greatest potential for possible health effects due to radiation. Data on particulate emissions are presented in other technical reports (2-5). [Theoretical Study] The theoretical emission data are presented in Table I. The estimates for the iron, zinc, and clay mines are based upon preliminary measurements taken by the Las Vegas laboratory. The estimates for the other mines were made assuming that 20% of the total radon-222 in the ore was released during the mining process and the radon release rate from the exposed ore surface was a factor of two greater than that resulting from mining. [ ] Dose assessments for radon from these mines were carried out using model facilities located on generic sites (1). The AIRDOS-II computer code (for estimating dispersion of airborne pollutants) with some minor modifications was used to determine working level exposures to a maximally exposed individual and a regional population. A conversion factor for risk/WL-year(O.021 fatal cancers/person-WL-y) was developed primarily from information on uranium miner exposures (6). This computer code and conversion factor were then applied to the assumed emission rate of radon-222 from each type of mine to develop estimates of working levels, lifetime risks and number of fatal cancers. A summary of this data is presented in table II. [ ] The highest estimated number of cancer deaths per year of operation is 0.05 cancer deaths or 1.0 death due to radon during the 24 year life of a phosphorous mine. For comparison, EPA estimates that underground uranium mines would cause .03 cancer deaths per year of operation in a regional population(1). [Field Study] As a followup to the theoretical study, EPA&apos;s Las Vegas laboratory began making measurements in 1978 of actual emissions of radon-222 and radioactive particulates from mine vents at several facilities for each of the industries listed in Table I and II. They were intended to verify general information and radon emissions from EPA&apos;s theoretical estimates.

Jan 1, 1981

By J. R. Sturgul

Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato&apos;s program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1 987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modem versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 1, 1987

By V. Anthony Cammarota

MINERALS INFORMATION PROGRAM Mineral data collection by the Federal Government actually began in 1882 with an appropriation by Congress to the U.S. Geological Survey (USGS). Although the Bureau of Mines was instituted in 1910, it was not until 1924 that the collection, interpretation, and dissemination of worldwide information on production, consumption, and availability of minerals became the responsibility of the Bureau. The objective of the Bureau&apos;s minerals information program is to maintain and provide reliable, timely, and comprehensive data for analysis of national minerals problems. This program is implemented by a staff of specialists who cover about 100 mineral commodities and the mineral industries of 168 countries. Data are also provided on the minerals industry on the State and county level. The specialists analyze information to identify trends and problems, forecast future U.S. and world supply and demand for the nonfuel minerals, and relate trends and developments to their impact on the domestic minerals industry. Data Sources and Publications The primary sources of data concerning the domestic minerals industry are the companies that produce, use, and trade in these minerals. Approximately 60,000 survey forms are sent to industry, on a monthly, quarterly, semiannual, or annual basis, to obtain the data. Domestic trade data are provided by the Bureau of the Census, U.S. Department of Commerce. Information on mineral developments abroad is developed by Bureau specialists from mineral reports supplied by U.S. embassies worldwide, from primary source documents, from a review of the technical mining literature, and from onsite mine and plant visits in foreign countries. The information is disseminated through a number of Bureau publications: "Mineral Industry Surveys" provide aggregated data on a monthly. quarterly, or semiannual basis to give timely information on the most important mineral commodities. "Mineral Commodity Summaries," published each January, provides preliminary annual data on supply and demand and discusses significant events of the previous year. The final data are published later in the "Minerals Yearbook," which is the definitive historical record for mineral statistics. "Mineral Facts and Problems," an encyclopedic work issued every 5 years, covers industry structure, technology, supply-demand analysis. economic factors, reserves, and forecasts of U.S. and world demand for individual commodities. "Mineral Perspectives" and "Mineral Issues" cover important international mineral developments and significant issues of current U.S. policy as they relate to minerals. Discussions and analyses of mineral trends and developments also appear in other Bureau publications, such as "Minerals and Materials" and "Information Circulars." These publications provide the basis for analysis and policy determinations by the Bureau and by virtually every Federal agency concerned with minerals, defense issues, the national economy, and foreign relations. The data are also used by industry in planning capital investments in mines and processing plants, by financial analysts, by U.S. delegations in their work with international commodity groups, and by a host of other minerals related organizations. Data Bases The data bases used by the specialists for preparing publications or in response to a continuous stream of inquiries include both those that contain individual commodity data from respondents, and those that are summary data bases on production, trade, capacity, employment and a number of other minerals-related items, not all of which are derived from data reported to the Bureau of Mines. The data bases maintained on the mainframes are not accessible by non- Bureau users. A 10-year data base of supply- demand data, published each year as an update of tables that appear for each commodity in Mineral Facts and Problems, is available on a floppy

Jan 1, 1987

By E. D. Attanasi, J. H. DeYoung

Although fraught with problems of completeness and comparability, statistical measures of mineral exploration in the United States point downward for 1985 and 1986. Exploration expenditures in the US domestic and Canadian companies have dropped steadily from a 1981 peak of about $400 million to about $190 million in 1985, according to a recent survey of exploration statistics by the Society of Economic Geologists (SEG). These totals have been adjusted to account for differences in the estimated coverage of exploration activity by each year&apos;s SEG survey. This survey is now supported by the US Bureau of Mines and the US Geological Survey (USGS). The drop in current dollar amounts does not take into account the effects of inflation, which would make the decline even more substantial. Metals Economics Group of Boulder, CO reported in its Mine Development Bimonthly that announced exploration budgets for 1986 indicated an even larger drop for the past year. Worldwide expenditures for companies covered by the report dropped from about $800 million to $750 million from 1984 to 1985 and plummeted to about $600 million in 1986. Exploration activity has been declining since about 1981. This has been due in large part to low prices for base and ferrous metals. Exploration budgets of mining subsidiaries of oil companies have plunged as parent companies try to conserve cash in the face of the sharpest decline in oil prices in nearly 40 years. Mining subsidiaries of petroleum firms that were either liquidated or divested recently include Anaconda (Arco), Getty Mining (Texaco), and Cyprus Minerals (Amoco). Exploration expenditures in Canada increased in 1984 in regions where gold is a traditional target. But there was little change in 1985, based on preliminary statistics from a federal government report (Energy, Mines and Resources Mineral Bulletin MR 211, 1986). Claim staking in Canada dropped 23% from 1983 to 1984 and declined slightly in 1985. Diamond drilling increased in 1984 to the record levels of 1980 and 1981. The ratio of exploration to development expenditures in Canada, however, fell from a 1981 peak of 0.9 to about 0.5 in 1984. The report also indicated that, since 1981, there has been a massive write-off of reserves with high production costs. Reserve levels of all major metals were down since 1981. Precious metals exploration accounts for an increasing share of total mineral exploration. For example, the SEG data show that 90% of 1985 US exploration expenses by domestic mining companies were devoted to base and precious metals, compared with only 51% in 1980. The restructuring of the mining industry has been accompanied by a decrease in response to the last two SEG annual surveys, but the trend towards precious metals was already established in earlier years. Trade journal reports suggest that the reduction of long-term interest rates has encouraged the mining industry to make cost-reducing capital investments in existing mines to maintain competitiveness. This is consistent with the observations that metals explorations in 1986 was characterized not by announcements of "grassroots" discoveries, but by on-property exploration on identified mines or prospects. In an effort to cut costs, gold mining companies have been following up on low cost production opportunities in their prospect inventories. Short-term, low risk, heap leach operations that can produce rapid returns on investment have been pursued. Specific exploration projects are covered in the individual state sections of this Annual Review. Even though economic growth continued steadily through 1986, the domestic mining industry has

Jan 5, 1987

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

By Thomas F. Stinson

Energy-producing states see severance taxes as attractive sources of increased revenues for otherwise tight budgets. Consumers in energy-poor states, however, protest that current rates are excessive and have moved to obtain a reduction. The US Supreme Court heard two cases questioning such taxes during its 1981 term, and Congress, in each of its last two sessions, has seriously considered measures placing a ceiling on severance tax rates. Although discussions usually focus on coal severance taxes levied by Montana and Wyoming, ramifications of changes in national policy are much larger, potentially affecting mineral taxes in all states. Severance taxes yield substantial revenues in some states, as illustrated in the accompanying table. In fiscal 1980, Texas collected more than $1.5 billion from such taxes, while Louisiana, Alaska, and Oklahoma collected $525 million, $507 million, and $436 million, respectively. Oil and natural gas production were the major items taxed. While the table shows only the 10 states with the largest severance tax collections, a total of 17 states had severance tax receipts exceeding $10 million in 1980. The enormous increases in severance tax revenue between 1970 and 1980 can be seen from the table by comparing columns A and B. For the 10 states shown, revenues increased from $650 million to $3.8 billion during that period, due to a combination of higher prices, increased production, and new or increased taxes. In most states, increases in prices and production were more evident than higher tax rates. Although the revenue increase is impressive, it understates the extent of changes occurring during the past decade. Since tax collections are shown for fiscal 1980, the full impact of the decontrol of domestic oil prices is not evident. Also, taxes on natural gas reflect controlled prices. When full de-control of natural gas occurs, significantly higher revenues can be expected in gas-producing states, even if tax rates, production, and world prices remain constant. These increases in severance tax revenues, coupled with further increases expected to accompany natural gas decontrol, have produced fears that a substantial transfer of income is taking place from residents of energy-poor states to those living in energy-rich areas. Others worry that increased severance tax revenues will be used to substitute for a substantial portion of state taxes that would have otherwise been collected from firms and individuals. The resulting improvements in tax climate, it is thought, may encourage firms and workers to migrate to energy-producing states. While these issues are often portrayed as pitting energy have-nots against the haves, such is not entirely the case. Much of the original impetus for limits on coal taxes came from Texas residents, the state collecting the most severance tax revenue. One way of gaining perspective on these concerns is by examining severance taxes per capita and as a percent of state tax collections (see columns C and D in the table). When this is done, Alaska, where 1980 taxes on oil and gas production totaled more than $1300 per capita (and 35% of all state tax collections), stands out as a special case. There, the state was able to eliminate some individual taxes, place revenues in a permanent trust fund, and consider offering a rebate of some previous income

Jan 4, 1982

By Frank Florez

INTRODUCTION The Magma mine, located at Superior, AZ, some 100 km (60 miles) east of Phoenix, was discovered in 1875, and was originally mined for silver. The property was acquired by W. B. Thompson who formed the Magma Copper Co. in 1910. Prior to 1965, square-set mining and cut-and-fill methods were used to mine steeply dipping veins at Magma. Ore was moved to the chute by gravity in the square-set stopes and by slusher in the cut-and-fill stopes. The stopes were gobbed with waste from the surface and development headings in the mine. The original square-set method of mining was modi¬fied in order to extract replacement ore bodies in limestones that dipped at 0.52 rad (30°) and varied in thick¬ness from 4.6 to 38 m (15 to 125 ft). Mining of these ore bodies was done by starting at the upper lateral ex¬tremities and retreating to the access openings. The timber square sets and cribbing were used as temporary support, the ground being allowed to cave as the mining retreated. It was found, however, that mining in such a manner was very inefficient; safety hazards increased be¬cause of the blocky and fractured characteristics of the ore and the weakness of the hanging wall. GENERAL DESCRIPTION The undercut-and-fill method of mining is now the primary stoping method used at Magma, and no pillars are left for later extraction. Four ore bodies are pres¬ently being mined. These ore bodies (see Fig. 1) dip conformably at 0.52 rad (30°) to the east with the host limestone and shale sediments, their average strike length is about 122 m (400 ft), and their thickness varies from 9 to 38 m (30 to 125 ft). The ore bodies are separated by varying thicknesses of barren rock. Three of them come together at various elevations primarily in the area of the main feeder fault, but there is an apparent horizontal displacement of about 23 m (75 ft) on the main feeder fault which complicates stope layout. The method as originally applied has been modified in order to mine more efficiently ore bodies that are 9 m (30 ft) or more in thickness. The modification was made to mine all the ore at a given elevation before dropping down for the cut below. The advantage of this is that mining is done on a horizontal plane and there¬fore muck removal can be mechanized. Also multiple faces are made available, thereby improving overall min¬ing efficiency. Another major change made was to carry a 6.7-m (22-ft) face when mining the top sill and a 6.4-m (21-ft) face when mining under fill rather than the former standard 3.35-m (11-ft) high face. This change lengthens the mining cycle and cuts mat prepa¬ration costs in half. Stopes are laid out (see Fig. 2) so that maximum mining panels are available and yet one stope crew will not tie up too much of the ore reserve. One stope might consist of as many as 20 panels, and these panels are divided evenly on opposite sides of the extraction cross¬cut. The stope layout is planned so that the maximum tramming distance to the orepass will not exceed 30.5 m (100 ft) on the crosscut and 38 m (125 ft) in the panel. Stope panel distances are sometimes exceeded when min¬ing to the extremity of the ore body. Tramming distance limits are determined by the efficiency of the com

Jan 1, 1982

By S. D. Thompson, L. Adler

J.R. Sturgul Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato&apos;s program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modern versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 12, 1988

By Ava Walker

The first form of a surety bond was an honest handshake between two or more parties agreeing to a decision, and their personal guarantee of following through to completion. This has all changed. In 1895, the United States Treasury Department disclosed that $35 million worth of personal surety guarantees on file had become worthless. A law was then passed requiring all surety bonds, in favor of the United States, must be corporate surety bonds. Today, a surety bond is one of the nation&apos;s leading fi¬nancial instruments used to guarantee the completion of an obligation. One hundred-fifty years before cor¬porate surety bonds, outcrops near Richmond, VA, were being mined. These surface mines became under¬ground mines. Today, both are still being used to obtain a leading energy source, coal. Since that time, more than 5956 km2 (1.47 million acres) of coal mined lands have been reclaimed in the US (Coal News, August, 1987). More than 25,000 state and Federal mining permits cover¬ing 14,164 km2 (3.5 million acres) have been issued during the last 10 years. Coal production has exceeded 7.2 Gt (8 billion st). More than 5665 km2 (1.4 million acres) of mined land has been reclaimed by active coal mining opera¬tions and 267 km2 (66,000 acres) of abandoned mined lands have been re¬claimed by others. Reclamation bonds were freely writ¬ten in the 1970s. So why are they almost extinct today? Contract bond losses have been severe in the past several years, sureties reporting losses exceed¬ing 110%. But the same proof is not provided on coal reclamation bonds. A surety bond is generally required when one party has an agreement with another party, and that party wants a guarantee from a third party that a job will be completed according to the terms and conditions of a written contract. In the case of a reclamation bond, the surety company (surety) is the financial party. It extends the credit and a guarantee to the obligee (the State, Commonwealth, or Office of Surface Mining) that the principal (the coal operator/company) will complete the terms and conditions of the contract (the rules and regulations governing mining and reclamation). The Surety Association of America defines a surety bond as an agreement providing for monetary compensation should there be a failure to perform specified acts within a stated period. Webster&apos;s Dictionary defines surety in the following ways: "l: the state of being sure; 2a: a pledge or other formal engagement given for the fulfillment of an undertaking and; 3b: one who has become legally liable for the debt, de¬fault, or failure in duty of another." Banks never make accommodation loans. Either the loan is good or no loan is made. Surety companies feel the same way about surety bonds. In fact, the average person does not realize the dangers of becoming surety for another. How does a surety determine if a company is worthy of receiving surety credit? How is a coal account under¬written today for an obligation that may not be released for many years? When a surety company executes a reclama¬tion bond, it financially puts its name behind the coal company and its guaran¬tee that should the coal miner default on the obligation, the surety will fulfill the contract. How is the surety to determine if a coal company may still be in business five, 10, 20, or 40 years from today?

Jan 1, 1989

By Rocky Gunderson

When operations begin early next year at the $100-million Port Kembla coal loading facility in New South Wales, Australia, a sophisticated computer system, directed by two of Hewlett-Packard&apos;s HP1000 mini-computers, will perform a number of functions ranging from monitoring and reporting arrivals and departures to maintaining a library of events for up to one year. The three-processor HP1000 system configuration, valued at $215,000, is one of the largest single orders, in terms of dollar value, ever submitted in Australia for Hewlett-Packard&apos;s line of engineering and manufacturing minicomputers. The processors will be linked in a fully "backed-up&apos;&apos; configuration using Hewlett-Packard&apos;s fourth generation distributed networking system, DS/1000-IV, making the system one of the most sophisticated in Australia. Interfaced to a number of weightometers and programmable logic controllers (PLCs), the computers will be the heart of a coal inventory system for the facility which, in its first phase, will be capable of handling more than 13.5 Mt/a of coal. The computers will report on all plant functions, including conveyor belt and water spray operations. Specifically, the system will: • Monitor and report all coal movements related to road and rail deliveries, dispatches from ship loaders, and interstockpile transfers. •Maintain a &apos;&apos;running log" of all events pertaining to overall plant operations, such as conveyor starts and stops and anti-pollution spray activation. • Accept and maintain plant data entered manually or acquired automatically from various remote locations via either visual display units (VDUs) or PLCs. • Maintain complete historical records of all transactions and related plant events for up to one year. • Provide a facility for stockpile management, modeling-type programs, and training or other simulation activity. The facility was designed with the following characteristics in mind, based on an analysis of requirements for an automated coal loading operation that would optimize productivity and be flexible to change and grow with facility needs and changing technology: • Continuous Operations-Due to the need for continuous plant logging and control, the overall facility will be capable of uninterrupted, 24¬hour operation. • Handling Current and Projected Workloads-The facility will be capable of not only handling current workloads, but also any additional workloads required during future coal loading operations. • Expansion-The facility will be capable of expansion, for a minimum cost, at any time with minimum disruption in operations. • Single Source of Supply and Maintenance-The facility will be supplied and maintained by one supplier, through hardware and software maintenance support contracts. System Configuration Two HP1000 minicomputers, each with 500K bytes of main memory, will be front-ended by a pre-processor with 256K bytes of main memory. These three systems, active, backup, and front-end, will be interconnected into a triangular array, as shown in the accompanying diagram. Under normal conditions, the front-end will transmit plant status data to one of the main systems, whose primary function will be to monitor coal flow and maintain a relevant dialogue with operators. The front-end, therefore, handles all communication with the plant PLCs, effectively removing this overhead from the current plant monitor (either of the two main systems). The front-end pre-processes and post-processes all information flowing from the plant monitor to the PLCs and vice versa, thus effectively handling all communication between the two units. A second main system will handle reporting, administrative, and modeling functions, and will also be capable of performing both front-end and monitoring operations. Linking all

Jan 11, 1981

By A. F. Agnew

Discussion by A.E Agnew Strachan&apos;s paper summarizes a wealth of data on water-storage dam "incidents" published by USCOLD and ASCE in 1988, together with a review of tailings-dam incidents published by USCOLD in 1994. The data is summarized by text and 11 histograms. The histograms present a useful compilation of these data, although the patterns within the histogram blocks did not survive the Mining Engineering printing process - so their usefulness is impaired. Unfortunately, the text discussion is too cursory and does not highlight the significant relationships among the various causes of the incidents. Four paragraphs of text and Fig. 1 were devoted to water-storage dams, but the discussion is too sketchy, and Fig. 1 is unclear. Important statistics that could be uncovered are: •the total number of dam incidents tabulated were 500+, •earth embankments constituted 73% of those in operation and •incidents related to earth embankments were 75%, of which dam failures accounted for 24%, major repairs accounted for 42% and accidents accounted for 34%. Strachan concluded that "the majority of the dam failures are associated with overtopping (p. 49), and that the majority of incidents are associated with spillway and other facility structures" - although this is difficult to discern from Fig. 1. Confusion regarding Strachan&apos;s use of the terms "dam failures" and "incidents" is compounded by his use of "failures" and "accidents" in one paragraph of his Introduction section followed by his use of "incidents" in the next paragraph. Getting to the meat of Strachan&apos;s important paper, the tailings-dam incident survey (USCOLD, 1994), the connection between Figs 2 through 11 seems obscure. First, in the four paragraphs of introductory material, one learns that "incidents consisted of failures, accidents, seepage and other incidents of performance that did not meet design criteria" (p. 50). One does learn the helpful caveat that "structures not related to mill tailings were not included in the review" - so that the Buffalo Creek (West Virginia in 1972) and Aberfan (Wales in 1966) coal-mine failures, together with the ongoing metal-mine remediation work at Summitville (Colorado) do not muddy the waters of his paper. The all-too-brief discussion of the data shown in Figs. 3 through 11 (185 dams in USCOLD plus 26 dams in UNEP) reveals the following: •Figure 3: 57% of the incidents (failures and accidents) occurred with dams less than 20-m (66-ft) in height. •Figure 4: 63% of the incidents were due to failures alone (subset of Fig. 3). •Figure 5: Active dams had 82% of the accidents and 93% of the failures. •Figure 6: Types of dams (upstream, water-retention, downstream, centerline and "unknown") separated according to incidents. •Figure 7: Breaks out the incidents in Fig. 6 by failures, accidents and ground water. •Figure 8: Breaks out incidents by type (overtopping, slope stability, earthquake, foundation, seepage, structural, erosion, mine subsidence and "unknown"). •Figure 9: Separates Fig. 8 data into active and inactive dams. •Figure 10: Separates Fig. 9 data into failures and accidents. •Figure 11: Same as Fig. 8, but broken out by tailings-dam type (Fig. 6). Figures 6 and 7 show that most of the failures are associated with upstream or "unknown" types. Figure 9 shows that the leading causes of incidents for active dams

Jan 1, 2003

By D. M. Range

Exxon is reclaiming an 80-hm2 (200¬acre) Wyoming uranium tailings basin in accordance with US Nuclear Regula¬tory Commission (NRC) requirements. The reclamation plan is designed to control the tailings and their radioactive emissions for at least 1000 years. Rigorous modeling and analyses of potential erosion by wind and water were used in planning. The use of riprap was minimized and the need for long¬term reclamation maintenance was eliminated. The resulting design is simi¬lar to regions stable from erosion cre¬ated by nature. The concepts used in the design and implementation have wider reclamation application. Highland history Exxon operated the Highland uranium operations from 1972 until mid-1984. Open pit and underground operations mined the roll front, sandstone ore body. The 2.5 kt/d (3000 stpd) mill employed conventional crushing, grinding, sulfu¬ric acid leach, CCD, SX, precipitation, and drying circuits. The mill produced 10 Mt (11 million st) of tailings. An¬other operator began commercial scale in situ leach operations in 1988. The tailings basin was constructed by deposition of mill tailings in a natural ravine dammed with a 30-m (100-ft) high by 1050-m (3400-ft) long clay core earthen dam built entirely downstream of tailings. Figure 1 shows the layout of the tail¬ings basin in 1984. Tailings were de¬posited along the dam face on the east side of the basin as well as in the west end and along the south edge until the early 1980s. This left a deep water pond in the middle of the basin. The deep pond was largely filled with tailings during the last four years of mill opera¬tions by the construction of two tailings causeways and the operation of a float¬ing tailings line. The pond water volume was mini¬mized by recycling tailings water to the mill and by operating a 32-L/s (500¬gpm) evaporation enhancement spray system during the last few years of mill operations. Regulatory requirements Several conceptual tailings basin rec¬lamation plans were prepared during the mine life. In September 1984, Exxon began preparation of a detailed plan in response to an NRC request. Water, Waste and Land Inc. (WWL) of Fort Collins, CO was selected to help pre¬pare the plan that was submitted to the NRC in December 1984. The design had to meet the require¬ments found in NRC regulations (NRC, 1985). These were based on regulations prepared by the Environmental Protec¬tion Agency (EPA, 1983) at the man¬date of federal law (UMTRA, 1978). The NRC regulations contain strict primary standards and a somewhat more flexible set of secondary standards. The primary standards include requiring that: • radiation from tailings be reduced to background levels; • radon gas emitted by the tailings be reduced to 20 pCi/m2/s from the surface of the reclaimed tailings pile; • tailings not be dispersed into the environment; and • these conditions endure without routine maintenance for at least 200 years and for 1000 years to the extent reasonably attainable. The lengthy time requirements pre¬sented a large engineering challenge. Radon is a radioactive, chemically inert gas with a 3.8 day half-life. It is released from uranium tailings by the radioactive decay of radium, which, in turn, is a radioactive decay product of uranium. Radon emissions from ura¬nium tailings can be controlled with an earthen cover thick enough that the radon gas decays to its solid, short-lived radio¬active daughters before the radon dif¬fuses through the cover material into the air.

Jan 1, 1989

By Peter Joralemon

Introduction The Sierra Nevada Foothill Gold Belt in California extends from Mariposa north for more than 420 km (200 miles). It includes the Grass Valley and Alleghany districts in the zone of Northern Mines and the famous Mother Lode to the south. The gold belt has produced more than 3.1 kt (100 million oz) of gold since its discovery in 1848. This remarkable production, at the present gold price, would be valued at more than $40 billion. The Law of Gambler&apos;s Ruin supposes that averages are based on systematic rather than random variations. It emphasizes the vast differences between finite and infinite probability. By applying this Law to this figure, it can be seen that the belt has produced an average of 15.5 t (500,000 oz) of gold per running mile. Many geologists believe, with some justification, that less than half the gold in this belt has been mined. Sixty per cent of the past production has come from lode deposits, the balance from Tertiary and Recent placer gravels. This paper will concern itself with the developing lode mines along the Sierra Nevada Foothill Gold Belt. As a further and final note regarding placer mining along this belt, Mark Twain suggested that placer miners, having lost their senses, had contributed liberally to the population of California&apos;s insane asylums. After a 40-year lull with little or no gold production, the lode mines of this famous belt are showing signs of renewed activity. Two open pit mines, the Sonora (Jamestown) and Carson Hill, are now in operation at substantial scales. Two others, the Goldenbell (Pine Tree-Josephine) and the Royal-Mountain King, are being readied for production on equally impressive scales. All are in the southern part of the Mother Lode. Exploration farther north, at Sutter Creek, Drytown, and Georgetown, is showing encouraging results in developing deeper lode deposits. This new activity has been sponsored to a large extent by junior Canadian mining and exploration companies. Most of the established American mining companies have looked the other way, not participating in this important development. One major reason for domestic disinterest in this opportunity is there is little chance for heap leachable open pit ore in this belt, excluding Carson Hill. And heap leaching has become fashionable with American mining companies today. Also, this great old gold belt must have been worked out, for why else is there so little activity here - Catch 22 logic. Another reason is that if a new deposit of size and grade similar to the mines in the past was found, high costs would preclude a profitable operation. And, finally, California environmentalists would not permit mining, even if a rich deposit were found. These may all be pefectly valid reasons not to explore for gold along this belt. But a look at the history of gold mining in California may suggest that the future for exploration and development of the gold resources in the Sierra Nevada Foothills can be greater than the past. It was during the Depression of the 1930s that this gold belt saw its maximum activity, with more than 3000 mines in operation. Some were father and son operations producing only a few tons of ore a day. Other mines employed hundreds of miners to hoist more than 900 t/d (1000 stpd). Some ores were of marginal grade. Others, like the Sixteen to

Jan 7, 1987

By G. J. Jansen

Introduction Coal petrography is the microscopic study and description of coal and other organic substances in terms of the microscopically recognizable organic constituents and of the rank of the material. Petrography studies of coal and other organic substances are useful in themselves, and have a number of practical applications. Some of these include determining coking quality of coal, estimating yields of methane from coal beds, and assisting in coal preparation. Petrography studies can also help in mine planning, in source rock studies, in combustion problems, and in synthetic fuel applications. Most recently, petrography has been found to be useful in studying sediment-hosted ore deposits. Microscopic constituents-macerals Under the microscope, coal is a heterogeneous assemblage of the coalified remains of woody matter and plant remains from the swamp or bog from which the coal was formed. The individually recognizable materials making up the organic mass are termed macerals by petrographers. They are the organic equivalent of the minerals that make up rocks. Coal petrographers can examine coal in two ways. Those interested primarily in the microscopically transparent macerals or in the study of very low rank materials, lignites for examples, like to use transmitted light microscopy where light passes through a microsection about 3 to 6 µm (0.0001 to 0.0002 in.) thick (Fig. 1). The dominant red color of the section in Fig. 1 is inherent, not a stain or produced by a filter. Distinct suggestions of textures in the reddish constituents can be seen. The red material is vitrinite and is thought to be the coalified remains of woody tissues. The yellow, lenticular substance is exinite. It is what remains of the waxy coating on a spore. Also seen are white dots of mineral matter and black opaque material that is better seen and described in polished sections. A polished microsection is prepared by grinding and polishing to a mirror polish a compact of coal and embedding resin or a coherent chunk of coal. The resulting microsection is then examined in a reflecting microscope. High magnification, 200X to 400X, and an oil immersion lens are needed to resolve fully the macerals of the organic matter so prepared. Figure 2 shows two macerals, an even gray vitrinite, unstructured and fusinite, a whitish, more or less cellular constituent. Fusinite is thought to represent more or less completely carbonized cellular material. Coal petrographers appreciate that coal is a heterogeneous material. Figure 3 is a view of another section. The generally structureless gray material is vitrinite. The bean-shaped dark constituents are exinites. The long, narrow, somewhat scalloped dark constituent is cutinite. Cutinite is thought to be derived from leaf coatings. Some coal petrographers would describe the large white, structureless mass as micrinite. Others might prefer the term macrinite. A few fragments of fusinite can also be seen. Figure 4 shows a coalified fungal remain, termed sclerotinite. It is surrounded by vitrinite and crushed fragments of fusinite all floating in a sea of embedding resin. Sometimes the microscope reveals the great heterogeneity of coal even on the microscope scale. Figure 5 shows a section with semi-fusinite, inertodetritinite, vitrinite, and micrinite. The nature of the heterogeneity may be judged by noting that the long dimension of the photomicrograph is about 70 µm (0.0027 in.). Measurement of rank Hoffmann and Jenkner (1932) discovered that measuring the reflectance of the vitrinite constituent of coal in a polished section gave a good measurement of the rank of the coal. In practice, a photomultiplier is used to mea-

Jan 9, 1987