Search Documents

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By M. Deniz Turan, HASAN NIZAMOGLU, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings, or flotation waste, formed during copper production may be considered in the class of valuable wastes because of the amount of copper they contain. With the decreasing grade values of copper ores, the utilization of wastes like tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental senses. This study was carried out with the aim of using ammonium derivatives for the recovery of copper from tailings waste produced during copper production and utilizing their complex formation characteristics. In the conditions of six hours of leaching at 30 °C in the presence of 22.5 percent ammonium hydroxide and 100 g/L ammonium persulfate, 91.47 percent of the copper was transferred into the solution, while iron was not transferred, indicating that copper can be selectively recovered from tailings.

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. Coteau, a wholly owned subsidiary of The North American Coal Corporation, produces more than 13.5 million tonnes per year, ranking it among the largest mines in North America. In 1993, Coteau ranked seventh in terms of annual coal sales, becoming the largest mine outside the Powder River Basin of northeastern Wyoming. However, for the Freedom Mine to stand among these Powder River heavyweights, Coteau over-came several obstacles, including a coal seam with three quarters the heating value and overburden to coal ratios three times higher than the Powder River mines. Coteau's ability to compete has been built around a program of continuous productivity improvement, cost efficiency, and innovation. This report highlights a few of the major improvements implemented in recent years.

Jan 1, 1995

By Peter G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the information necessary in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included the following : (1) careful checks on the sampling and assaying (2) selection of representative samples used to establish the recoverable amounts of precious metals in the ore (3) examination of underground workings driven to provide samples both for metallurgical testing and for assay comparisons (4) evaluation of plant site and waste dump areas as non-mineral, including a placer examination of the taillngs disposal area (5) location of an adequate water supply. All these investigations were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1981

By Thomas Schultheis, William Heron, Paul Watson, Colin Warren

This paper describes the geology and geotechnics associated with construction of the Thames Tunnel, part of the UK’s Channel Tunnel Rail Link (CTRL). The 2.5km long twin tunnels run beneath the river Thames at depths of up to 40m and are currently under construction. They pass through varying geology comprising alluvium, terrace gravels and chalk with flints and are currently being bored using Herrenknecht mixshield slurry tunnel boring machines (TBM’s). This paper outlines the lithology and engineering properties of each geological formation and describes the geotechnical processes, potential hazards and difficulties experienced in the works. A summary is given into the extent of the investigative work in terms of route selection, tunnel design, TBM optimisation and further details are provided on the geotechnical aspects associated with the construction of the tunnel approach structures and the tunnels.

Jan 1, 2003

By Jeff Schwoebel, Arcy, D&apos Horner

The Deep Coal Seam Project is a multi- year, large-scale research and development effort between the Gas Research Institute (GRI) and Resource Enterprises, Inc. (REI). The project is being conducted at the Red Mountain Site, a multi-well test site located in the southeastern portion of the Piceance Basin near Collbran in Mesa County, Colorado. The project objective is to develop the drilling, reservoir evaluation, completion and production technology required to produce gas from a thick, deeply buried coal seam. To understand the parameters controlling gas production, project efforts are focused on the Cameo "D" coal reservoir which lies at a depth of about 1707 m (5,600 ft) at the test site. This paper overviews the drilling, testing, completion, and production techniques used on the 1, 2 and 3 Deep Seam wells and implications for resource development.

Jan 1, 1987

By Indranil Roy

Gua supergene enriched iron ore deposit from Jharkhand, India has been geostatistically modeled. Population modeling shows a negatively skewed 3-parameter log-normal fit for Fe and positively skewed 3-parameter log-normal fit for Al2O3 and SO2. Semi-variographic studies for Fe indicate spherical function fit using point kriging cross-validation technique with Co=4.06(%)2, C5.11 (%)2, Co+C=9.1 7(%)2 and 'a'=348m. Kriging with 50mx50mx 10m block size at 740mRL led to a global mean kriged estimate of 61.98% and kriging variance of 4.04(%)2 for Fe with central 90% geostatistical confidence limits at 61.39% and 62.24% for that level. This led to an ore inventory at 740mRL as 7.29 million tonnes of ore.

Jan 1, 2002

By John L. Stafford

The ROEMMC combustion system was originally conceived as a means of utilizing solid fuels that would otherwise have been wastes requiring disposal and convert these fuels into useful energy sources. This concept follows as an extension of the application of residual waste incineration with energy recovery practiced in the lumber, manufactured board, sugar cane, and other industries. The incineration of these wastes in the furnaces of steam generating equipment is thoroughly described (1, 2, 3, 4, 5, 6, 7). The fundamental principle of the ROEMMC system is temperature control which makes possible the maintenance of the non-combustible fraction of these solid fuels in a dry solid state and their separation from the gaseous products of combustion. This philosophy of ash removal and the "slagging" philosophy are compared. The ROEMMC equipment function and applications are described.

Jan 1, 1978

By Kewal K. Kohli, Richard E. Thill, Syd S. Peng

The results of unpublished investigations into surface subsidence from coal mining in the Northern Appalachian Coalfield are summarized. These investigations were carried out by various coal companies and the State of Pennsylvania in the sixties and seventies. Subsidence data were collected and analyzed from 10 room-and-pillar panels in 5 mines in the Pittsburgh coal seam. Results show that angle of draw ranges from 26° to 33° and subsidence factor from 0.42 to 0.72; surface heating generally occurs beyond the edges of the panel, the amount and extent of which vary; waviness occurs in the subsidence profile if a substantial number of pillar stumps are left in irregular patterns; interpanel effect is significant; time-dependent subsidence exists, but varies for different panels; and surface slope does not seem to affect the amount of subsidence.

Jan 1, 1982

By Wen L. Cai

This paper examines the effects of different block dimensions and cone bases on the economic open pit limit design based on case studies on a coal deposit consisted of two west- east elongated, near vertical thin seams starting with a base model dimension of 200x170x50 (NX*NY*NZ) with a block dimension of 10mx5mx4m (DX*DY*DZ), the blocks were combined along easting, northing and elevation directions. Two cone bases were used, one with a base radius of 10 meters, the other with a base radius of 0. Two pit design algorithms, one is the floating cone algorithm, the other is an optimum algorithm, were used to see which one of the two pit design algorithms is more sensitive to block dimension and cone base variations. The results are presented and analyzed.

Jan 1, 1992

By Dae S. Young

The Disjunctive Kriging (DK) procedure was developed to estimate ore recovery figures within a deposit/ domain from limited diamond drill hole (DDH) core assay data taken at the exploration stage. Local recovery figures include minable ore tonnage and ore grades within relatively small areas such as stopes or small panels on a pit bench, for a given cut-off grade. The grade and tonnage should be computed based on the true selective mining units, that is, the average grade distribution of selective mining units within a panel. Local recovery figures are critical information for economic and engineering feasibility studies before mine development, as well as for short-term mine planning for operating mines. This kind of information can be provided only by non-linear geostatistical methods including DK and the Multivariate Gaussian Approach (MG) (Journel, 2, Parker, et al, 5).

Jan 1, 1982

By R. Woods, O. A. Kiehn, C. A. Born, F. N. Bender

Development of the flotation reagent scheme at Climax Molybdenum Company's mine at Climax Colorado is reviewed. Features of the mineralogy, milling practice and background of reagent changes are outlined. Special attention is given to the hitherto unpublished details of the application of depressants for copper and lead impurities. The present rougher flotation reagent scheme utilizes a neutral hydrocarbon oil, low in unsaturates and wax, as collector with a sulfated coconut oil emulsifier and pine oil frother. Lime and sodium silicate are used as rougher conditioning and slime dispersant agents. Chalcopyrite and galena impurities are de- pressed in both rougher and cleaner plants by stage addition of Nokes reagent and sodium cyanide to yield a metallurgical grade molybdenite concentrate containing greater than 90% molybdenite and less than 0.5%, 0.1% and 0.05% iron, copper and lead impurities, respectively.

Jan 1, 1976

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Cheng, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates have wide application in global smelting operations, comprising primarily of chalcopyrite (CuFeS2) as the principal mineral, accompanied by chalcocite (Cu2S) and bornite (Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates frequently harbor detrimental impurities, notably fluorine ions, which can cause various complications during the smelting process. Moreover, an elevated fluorine content in copper concentrates may entail financial penalties and sales constraints. This review conducts a comprehensive analysis of existing methods for the removal of fluorine, presenting a nuanced assessment of their merits and demerits. It also provides valuable insights into the current landscape of fluorine elimination from copper concentrates and pinpoints pivotal areas warranting future investigation. This review endeavors to serve as a pragmatic resource for researchers and industry professionals operating within this domain.

Jan 1, 2024

By John Rajala

The Otjikoto Gold Mill was commissioned during November–December 2014 as Namibia’s first new gold producer in 30 years. Its operations consist of surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and gold recovery. The initial mill design capacity was 2.5 Mt/a. Its capacity was expanded after nine months of operation to 3.1 Mt/a, and process performance has significantly surpassed design expectations. After startup, the Otjikoto Mill’s throughput and gold recovery ramped up quickly, with both parameters exceeding design after only two months of operation. The robust process performance continued into 2019, with key performance indicators (KPIs) eclipsing design values in almost every aspect of mill operation. The Otjikoto Mill’s gold recovery is exceptionally high, exceeding 98 percent every year following startup, especially considering the low-grade nature of the deposit.

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

A high calcium fluidized-bed combustor ash was shown to be an effective binder for iron ore pellets at dosages of 1 % to 2% of the magnetite concentrate weight. Magnetite pellets that were between 1.1 and 12.7 mm (7/16 and 1/2 in.) in diameter were produced with dry crushing strengths greater than 22.3 N (5.0 lb-force) per pellet, which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. The addition of calcium chloride at a rate of 0.1 % to 0.2 % of the total powder weight increased the strength of the dried pellets by as much as 22 % compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1999

By Qun Wang, Elena A. Alonso, Janusz S. Laskowski

Primary normal long-chain amines are insoluble in saturated brine. Their colloidal solubility (dispersion) in concentrated electrolyte solutions is strongly affected by the presence of surfactants (frothers). This paper shows that a better usage of alcohol type surfactants, which are commonly used in potash ore flotation as frothers, can significantly improve the flotation of both coarse and fine sylvite particles. A new process of potash ore flotation is developed, which includes premixing an effective frother with an aqueous solution of amine or emulsion of extender oil containing amine. With such a combination of flotation reagents, KC1 particles up to 5 mm in size float very well in the short flotation column, and particles up to 2 mm float in a mechanical cell; when used to treat fine fraction-containing sample, this method may as well provide an improved concentrate grade.

Jan 1, 1995

By M. Gaft, G. Panczer, R. Reisfeld, L. Nagli

Laser-induced luminescence and breakdown spectroscopy methods appear to be a good tool for real-time evaluation of dolomite content on moving belt. The distinctive feature for time- resolved luminescence is Dy3+ emission in apatite, which is excited by 251 nm laser light and detected with delay time of 5 ms and gate width of 1 ms. The distinctive features for breakdown spectroscopy are 604 nm line of F and P in apatite and 518 nm line of Mg in dolomite. The representative sampling of more than 200 pebbles has been studied by both methods. By luminescence method 100% of dolomite will be identified, while approximately 15-20% of apatite with extremely week Dy3+ luminescence may be mistakenly counted as dolomite. By breakdown spectroscopy the identification is 100% correct both for dolomite and for apatite.

Jan 1, 2002

By B. J. Arnold, F. F. Aplan

A model incorporating rate and residence time to describe the froth flotation process was used to provide data for the evaluation of various kinetic flotation models and to provide scale-up information from laboratory to industrial scale coal froth flotation. Rate constants were determined in laboratory and plant froth flotation tests and the residence time distribution was measured for a bank of four 21 ft 3 (0.6 m3 ) WEMCO cells treating Upper Freeport seam coal and a bank of four 300 ft 3 (8.5 m3 ) cells treating Lower Kittanning seam coal. It was found that a lag time for continuous flotation should be incorporated into scale up models and that a kinetic froth factor ratio of between about 2.0 and 2.8 should also be used to scale up data from laboratory to plant scale.

Jan 1, 1989