Search Documents

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974

By T. McCallum, C. Cooper, B. Hutzler

"In copper solvent extraction, managing the quality of the organic phase is a key parameter to ensure optimal physical and metallurgical performance in the plant. Increased throughput as a result of declining ore grades coupled with advances in plant design and practice, resulting in reduced organic losses, has pushed the limits of the status quo with respect to organic quality. Clay treatment of plant and recovered organic at the optimal dosage is critical in maintaining quality, however, achieving the optimal dosage through existing filtration capacity and practice can be difficult. Cytec has developed a process aid that increases efficiency of existing filtration equipment that has been successfully implemented at two commercial SX operations. ACORGA® CB1000 enables higher dosages of clay while allowing for more efficient use of existing filtration capacity. This study analyzes results from commercial trials and demonstrates that improved organic quality and clarity is achievable through optimization of current treatment practices. INTRODUCTION Decreasing ore grades have prompted copper solvent extraction operations to raise PLS flow rates, increasing plant throughput to maintain production1. The ability to process higher flow rates through existing mixer-settlers historically came at the expense of increased entrainments2. However, advances in mixer-settler design, practices and improvements in organic recovery processes have enabled operations to maintain, and in some cases reduce organic losses while achieving higher flow rates through existing equipment. Based on the increased demand on the SX equipment and reduced losses (or more efficient recovery) maintenance of the circuit organic quality through efficient clay treatment is now more important than ever. This paper discusses common industry practices and related issues in organic clay treatment, and presents benefits achieved in commercial operations through the use of ACORGA® CB1000 Clay Binder. IMPROVEMENTS IN DESIGN AND PLANT PRACTICE Mixer-settler design has improved since the first commercial copper SX operation in the late 1960s. Advanced designs in mixer, settler, and settler internals have contributed to reductions in entrainments. For example, improved impeller designs have been reported to decrease organic in aqueous entrainment from the ‘old designs’ of 50-200 ppm3 to as low as 4 – 10 ppm confirmed via diluent and reagent consumptions . Similarly, operations are reporting a 20-50% decrease in reagent consumption when compared to the original design criteria3. Operations have optimized settler internals to increase coalescence and have improved settler operating practices which have been shown to reduce entrainments7. Comparison of the SX world operating data from 1999 and 2007 shows reductions in organic entrainment losses with increases in flow rates."

Jan 1, 2015

By Alessandro Navarra, Aldo Quelopana

For decades, open-pit mine planning algorithms have incorporated geological uncertainty and other elements or characteristics for increasingly realistic representations. Among these complexities is the detailing of downstream processes that occur inside processing plants. Previous studies have demonstrated that the strategic mine plan and mineral concentrator design are coupled, and should therefore be optimized simultaneously within the same quantitative framework. However, existing frameworks offer limited representation of operational modes. This work demonstrates an approach to resolving this gap, in an optimization based on a parallelized Variable Neighborhood Descent (VND). The resulting algorithm embeds mass-balancing linear programming (LP) using a DantzigWolfe decomposition. A case study of a Zn-Pb deposit is presented to show the performance reached.

Jun 25, 2023

By G. Paul Anderson

Personnel at Utah Copper Division's Bingham Canyon Mine use current computing technology to compile pertinent production statistics and mining plans. Within hours after the day's work has been completed, concise reports summarizing the previous day's production statistics, actual production vs. budget statistics, the location of shovels relevant to the mining plan, the performance of equipment, equipment next scheduled for maintenance, etc. are available at the terminals located throughout the mine. Also, engineering personnel us e computerized systems, directly from their offices, to assist them in the timely development of mining plans. Timely and concise reporting and planning capabilities such as these assist mine personnel in their efforts to review mining progress and equipment performance, and as such they are in a better position to detect adverse trends early and to seek appropriate resources or make changes in plans or practices.

Jan 1, 1977

By S. A. Montague

In spite of the many new insulating materials, both synthetic and manufactured, that have been put on the market since the end of World War II, and notwithstanding the many millions of dollars applied to the development of synthetic mica, natural block mica1 is still a most indispensable insulator in various electronic components. It will remain so, barring some spectacular break-through in research that might provide a substitute fully acceptable as a replacement for mica in all of its superior properties. But this is not to say the future for mica is assured, or free from serious problems. Technological advances have created problems requiring a solution to be found if future requirements are to be filled.

Jan 1, 1962

By J. A. Herbst

It is widely recognized that Semiautogenous Grinding (SAG) circuits require the use of effective process control techniques to achieve their full processing potential and to protect them from the harmful effects of overloads and grind-outs. This requirement is even more essential as the variability of the ore being processed increases. The new Chino Mines Company concentrator located near Santa Rita, New Mexico started operation in June of 1982. At least eight major rock types are mined and milled. Ore hardness, feed size, and specific gravity are quite variable. Typical feed rates per grinding line are 850-900 tph but extremes of 260-1200 tph have been encountered. Normal feed rate variations of between 400 and 1100 tph are encountered on a weekly and sometimes daily basis. Feed size varies with rock type from a maximum of eight inches for the harder ores to two inches for the softer ores. One somewhat unique characteristic of the Santa Rita ore body among major copper mines is the wide variation in ore specific gravity. Specific gravities of the major rock types range between 2.7 and 3.6. The specific gravity variations are due to large changes in magnetite concentration throughout the pit. The result of this is large variations in SAG mill throughput which can have a harmful effect on downstream ball milling and flotation performance. Due to these wide fluctuations in ore characteristics, it was recognized soon after startup that successful operation of the grinding circuit and the plant at large was dependent upon the development of an effective automatic grinding control strategy. Research at the University of Utah has suggested that control based upon critical but difficult or costly to measure variables would improve automatic control performance. A project team made up of the Chino process control staff, Kennecott's Process Control department and the University of Utah Metallurgy Department was established to assess these concepts at Chino. This paper describes the development and on-line plant implementation of an Extended Kalman Filter that uses simple models of the SAG milling process, to predict the volumetric loading, the rock mass, the water mass, and the ball mass within the SAG mills at Chino. The on-line estimation of these parameters is the first step in the development of an integrated SAG mill/ball mill control strategy which is hoped to L eventually maintain the grinding circuit at its maximum capacity, while balancing the grinding load between the SAG and ball mills. Examples of long term estimation with the models and filter are shown for typical operating conditions as well as a SAG mill overload and grind-out.

Jan 1, 1983

By K. V. Raj

"Air inversion is a meteorological phenomenon generally occurs during winter times. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for health and safety of miners. Mine operations cease if the concentration of NOx or CO exceeds the threshold limit value (TLV) of the pollutants. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Studies of the turbulence parameters suggest that effective ventilation of the pit and removal of pollutants can be accomplished if a large enough mixing length in the open pit can be created. Turbulent mixing by eddies of different length scales under an inversion layer is product of wind shear, thermal gradient and buoyancy. The main result of turbulence is mixing of the atmospheric profile and transport of momentum. Computational fluid dynamics (CFD) Simulation results of a novel mitigation approach using cloud cover will be presented in this paper. INTRODUCTION In extreme climatic conditions, deep open-pit mines tend to trap pollutants at the pit bottom due to air inversions. Keeping open pits adequately ventilated is a considerable challenge for the mining community. Mine operators in cold regions are very familiar with this problem, the severity of which can be judged from Figures 1 and 2. The top portion of the figures show clear sky and snow covered benches. The brown haze, containing various contaminants accumulated over time in the pit under the air inversion, can be seen in the bottom portion of the figures. Several Arctic or subarctic mines have reported air inversions. Even Rio Tinto’s Bingham Canyon pit in Utah has reported local air inversions from time to time [1].Mitigation of pollutants in deep open-pit mines in the Arctic is a challenging task. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for human health. Mine operations cease if the concentration of any one of the pollutants (NOx or CO) exceeds the TLV. Sustained cessation of a mine operation has serious economic consequences. For continued mining operation, the levels of pollutants must be below the TLVs. If no significant synoptic meteorological situation changes during an inversion, a warm air mass sits over the cold air mass within the open pit. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Some of the early approaches in artificially ventilating open pits were attempted in the USSR. Most of the studies by Soviet researchers suggested the use of turbojets and turbo-propeller engines, airscrews, axial pit fans, and meteotrons [2, 3]. However, the majority of these studies were only theoretical in nature, with no evidence of an approach that really worked in practice."

Jan 1, 2017

By J. S. Chen

DOE recently funded 21 projects under the solicitation by its Environmental Restoration and Waste Management Division. This project is combining the expertise of an interdisciplinary team of researchers with that of three manufacturers to isolate nuclear waste storage sites using remote longwall mining. The concept is being pursued in Germany, too. This paper will present the conceptual approach to the project and discuss the problems in transferring longwall mining technology to nuclear waste containment.

Jan 1, 1994

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By Xinyang Wang

It is believed that sulfur and volatile matter contents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal - three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Thomas L. Hurst, Joseph M. Hans

INTRODUCTION The former Shiprock uranium mill site is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the mill site are located on the Navajo Indian Reservation. The millsite was built on a 230 acre tract leased by Kerr-McGee Oil Industries Inc., and was operated from 1954 to 1963. The Vanadium Corporation of America and its successor, the Foote Mineral Company, operated the mill from 1963 to 1968. During its entire operation, 1.5 million tons of uranium ore was milled producing 3711 tons of U308 concentrate. The concentrate was sold to the former U.S. Atomic Energy Commission. During milling, the ore was crushed to less than 35 mesh and acid leached to remove the uranium. The [ ] uranium was removed from the leach solution by solvent extraction and the uranium-barren solution discharged into raffinate ponds for disposal by evaporation and seepage. The spent solids (tailings) were pulped with waste process fluids and water and discharged to form tailings piles. The piles (ponds or dams) were formed with earth starter dikes. The dike walls were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. Since only a small fraction (0.25 percent) of the ore was U308 by weight, most of the ore bulk ended up as wastes. The wastes contain nearly all of the uranium decay chain radionuclides present in the ore except uranium. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and wastes reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a Tribal enterprise. In order to provide skilled personnel to operate earth moving equipment, a heavy equipment operator's training school was also established on the mill site and was administered and operated by NECA. The U.S. Public Health Service (PHS) and the Environmental Protection Agency (EPA) staff conducted radiation surveys at four inactive uranium millsites on the Navajo Reservation in April 1974. During the survey of the Shiprock millsite, it was noted that the training activities were degrading its radiological condition. Both the PHS and EPA staff recommended that the training activities be directed towards the decontamination of the millsite area and interim stabilization of the tailings piles. Preparation for the decontami-nation work commenced in April 1974. In order to facilitate the decontamination activities, the mill site and its contaminated environs were divided into major areas labeled A through F (Figure 2). Areas A, B, and C are defined as "perimeter" areas and contained surface contamination ranging from 5 to 30 cm deep. Area D defined the mill yard and contained contamination ranging from 0.6 to 5.5 m deep. Area E contained several raffinate ponds which were removed to line up the northwest boundary of the tailings pile and to move the contaminants away from the vicinity of the occupied on-site buildings. The contaminants in Area E ranged from 0.05 to 5.5 m in depth. Area F encompassed the ore storage yard. Contaminants in this area ranged from 0.18 to 1.2 m deep. Washes, however, had contamination exceeding 7.6 m deep.

Jan 1, 1981

By K. J. Reid, I. Iwasaki, T. Sabelin

Introduction Occurrences of platinum group minerals (PGM) in mafic and ultramafic rocks in association with Cu-Ni mineralization are well known. Yet for the Duluth Complex, a large body of dominantly mafic igneous rocks in northeastern Minnesota with significant Cu-Ni mineralization (Bonnichsen, 1972; Boucher, 1975; Watowich, 1978; Weiblen and Morey, 1980), little has been published concerning its platinum group element (PGE) contents and mineralogy. In a previous study of massive sulfide rock, sperrylite (PtAs2) was found in nickel arsenide and recovery of arsenide minerals by flotation has been investigated (Iwasaki et al., 1986; Ryan and Weiblen, 1984). Recently, an announcement was made of the discovery of significant quantities of platinum and palladium [peak assay values of 9 g/t (0.27 oz per st)] in an interval of a drill core with disseminated sulfide mineralization 16 km (10 miles) southeast of Ely, MN (Anon, 1985; Sabelin, 1985). This paper describes PGM from the Pt-Pd-enriched zone and evaluates their potential for concentration. Geologic setting The Pt-Pd zone occurs in the South Kawishiwi in¬trusion near its basal contact at 734 to 737 m (2408 to 2418 ft) depth. The South Kawishiwi is one of several minor mafic intrusions that constitute the western margin of the Duluth Complex near Ely, MN (Fig. 1). It is com¬prised of a 70.1- to 350.5-m (230- to 1150-ft) thick sul¬fide-bearing basal unit of troctolite with minor amounts of anorthosite, norite, picrite, and oxide layers overlain by a troctolite unit with interlayered anorthosite (Bonnichsen et al., 1980; Foose, 1984; and Foose and Weiblen, 1986). The basal unit, in which the Pt-Pd zone is found, is markedly heterogeneous in rock type, lacking any coherent internal stratigraphy, and shows evidence of both pre- and post-consolidation faulting (Foose and Weiblen, 1986). Geochemistry Chemical analyses were made on 0.3-m (1-ft) intervals of crushed drill core material (1/4 core, BX size) at 731.5 to 740.7 m (2400 to 2430 ft) depth and the results are presented in Fig. 2. The analytical techniques used were atomic absorption spectrometry for silver, chromium, copper, and nickel; a coulometric titration method for sulfur; and a combined fire assay-DC plasma technique for gold, palladium, and platinum. Figure 2 shows the significant enrichment of platinum and palladium at 734 to 737 m (2408 to 2418 ft) depth; it corresponds to a stratigraphic interval rich in oxide minerals. Average values for platinum and palladium contents over the 3-m (10-ft) interval are 2520 and 2580 ppb, respectively, or 5.1 g/t (0.15 oz per st) platinum plus palladium. Platinum plus palladium contents from individual 0.3-m (1-ft) intervals are as high as 9120 ppb or 9.1 g/t (0.27 oz per st) and average 7.4 g/t (0.22 oz per st) in a 1.5-m (5-ft) interval in the richest part of the zone. The Pt-to-Pd ratio is nearly 1:1 over the entire 9.1-m (30-ft) interval and the platinum and palladium correlate closely with chromium, which ranges from 1.9% to 5.3%. Copper, nickel, and sulfur contents for the drill core interval are also given in Fig. 2. In¬terestingly, the Pt-Pd high corresponds to a depletion in copper, nickel, and sulfur. Mineralogy of the Pt-Pd zone The Pt-Pd zone occurs within an oxide-rich zone or layer that consists essentially of oxide minerals, plagioclase, and olivine. The oxides may constitute as

Jan 1, 1987

BP Minerals America (BPMA) has completed its $400 million modernization of Kennecott Utah Copper's Bingham Canyon mine. Modernized facilities include the in-pit crusher, conveyor, ore storage area, concentrator, ore pipe-line, and tailings pipeline. With modernization, Kennecott will achieve substantial cost reductions. Bingham Canyon is now one of the lowest cost copper producers in the world. And the mine will continue to provide jobs and income in Utah for another 30 years or more. The Modernization Project began in February 1986. The work took 33 months. In late 1987, the construction force peaked at 1100 workers. Kennecott Utah Copper now employs a permanent work force of 2100 employees. Less equipment and more efficiency The modernization work has increased the scale of the facilities that transport and process copper ore. A large, continuous transport system has replaced multiple haulage units. Fewer but larger pieces of equipment have replaced many crushing, grinding, and flotation units. The result is less maintenance, fewer employees, and improved metal recoveries. About one-third of the $400 million modernization project is directed at improving ore movement by eliminating rail transport. The new concentrator accounts for the remaining two-thirds of the modernization investment. The modernized plant was started up in stages. In February, ore was fed to the crusher. By the end of March, the three grinding lines were operating and the flotation circuit was producing copper concentrate. In July, the design through-put rate of 70 kt/d (77,000 stpd) was reached. October saw the achievement of targeted metal recoveries that corresponded to the fully modernized operation. It is estimated that Bingham Canyon will annually produce 181 kt (200,000 st) of refined copper, 9.3 t (300,000 oz) of gold, 71 t (2.3 million oz) of silver, and 5.4 kt (12 million lb) of molybdenite. Current Bingham Canyon production is about 97 kt/d (107,000 stpd) and a similar amount of overburden. Some 70 kt/d (77,000 stpd) of ore are processed through the in-pit crusher and 27 kt/d (30,000 stpd) of ore are transported by rail. The Bingham Canyon mine has yielded more than 11 Mt (12 million st) of refined copper. In 1863, precious metals - silver-bearing lead - were first discovered in Bingham Canyon. What was once a mountain is now a huge open pit. In fact, the mine is the world's largest man made excavation. The pit is some 4 km (2.5 miles) wide and 0.8 km (0.5 miles) deep. Since the pit began operating in 1906, more than 4.5 Gt (5 billion st) of material have been removed. Modernized facilities Electric 21 m3 (27 cu yd) or 23 m3 (30 cu yd) shovels are used to load the haulage trucks. Both 154 t (170 st) and 181 t (200 st) trucks are used to haul the ore to a mobile, in-pit crusher. The crusher replaces three crushers located at the old concentrators. There are two dumping locations at the new crusher, which can handle two trucks a minute. The 1.5 x 2.7 m (60 x 109 in.), 745 kW (1000 hp) Allis-Chalmers gyratory crusher reduces the ore to 254 mm (10 in.) size or less and delivers it to the conveyor. The crusher and conveyor systems are capable of handling 9 kt/h (10,000 stph) of ore.

Jan 11, 1988

By William C. Cassun

The important role of pit slope design in the overall economics of open-pit mining ventures has long been recognized and well documented.1 2 Any economic analysis of a pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. The conventional practice in pit slope design is based on the factor of safety analysis.' The approach uses average values to arrive at a deterministic solution to slope stability. Past analyses based on this approach generally have had several drawbacks: 1. The risk from slope failure could not be quantified. 2. Only relatively simple pit wall geometries were considered. 3. The analyses were performed solely for the benefits of steeper slopes, seldom discussing the potential costs of slope failures. 4. Analyses were seldom considered in a year-by-year mine planning context. Recognizing that average values do not reflect the uncertainty in geomechanical parameters, a probabilistic philosophy to slope design has evolved. 4,5 However, this approach had not been fully developed to include complex slope geometries and mine planning consideration. In order to develop an integrated, pit slope design procedure, a research project was initiated at the University of Arizona during 1973 in conjunction with the Canada Center for Mineral and Energy Teleology. This research resulted in the development of a probabilistic design procedure. The remainder of this paper gives an overview of the probabilistic design procedure and a discussion of the requirements for the benefit-cost analysis of a pit slope design. Finally, the results of a case study undertaken at an operating mine are given.

Jan 1, 1977

By G. Mike Bernard

The Andacollo gold mine is located near the town of Andacollo (population 14,000 people) in Chile’s region four. It is about 56km (35 miles) by paved road from the coastal city of La Serena. Santiago is about480 km (300 miles) south. Site elevation varies between 1,000 and 1,280 m(3,300 and 4,200 ft). The climate at the Andacollo site is moderate but arid. Average annual rainfall is only 130mm (5 in.). Because there is little rain and the temperature varies only a few degrees (14 to 24 C or 57 to 75F), there are no problems with freezing, solution dilution or pad saturation. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By Stanley M. Moos

The Pueblo Viejo gold/silver mine, located in the Dominican Republic, started production in early 1974 processing ores averaging 4 g/tonne gold and 20 g/tonne silver at a rate of 7,250 tonnes/day. The ore milled is a silicified siltstone with average work index of about 8 that occurs as an extensive oxide capping of a primary sulfide orebody. The sulfide ores are refractory to conventional treatment process and extensive research work is now in progress to develop a treatment process for them. The ore deposit has a long history having been mined by the indigenous Arawak Indians (for some time in the early sixteenth century) prior to the arrival of the Spanish and then by the Spaniards. In the early 1950?s, Italian engineers attempted to process the sulfide ores. Mining by the Indians and Spanish was abandoned because of low grade and little coarse gold in the oxide ores and by the Italians because of the refractory nature of the sulfide ore. In 1969, Rosario Resources geologists discovered that there existed sufficient reserves of oxide ore for a viable mining operation and accordingly, the plant was designed, built and brought into production.

Jan 1, 1979

Improvements in computer technology and associated software have allowed the improvement and development of more advanced ventilation modeling software packages including those that have the ability to simulate the effects of a mine fire on the ventilation system in terms of heat, smoke and gas distribution. This ability has real applications for the mining industry in terms of emergency planning, training and response. The primary focus of this paper will be the benefits to training programs that this type of software can provide to all types of training for various personnel, from the newly hired inexperienced miner, mine rescue, atmospheric monitoring personnel and emergency evacuation drills. The results of the simulations can then be used to give miner?s more detailed information on what types of conditions they may face based on the type and location of the fire and the program itself can be used to manipulate the ventilation system in a way that emergency response personnel may (i.e. tear down stoppings to reduce airflow to the fire area) and see the effects in real-time.

Jan 1, 2012