Search Documents

By S. Sinha, S. Ganguly

"In an opencast mine explosives are used for fragmentation of rock. Inefficient use of explosive energy in an opencast operation produces excessive ground vibration, which is measured by peak particle velocity (PPV). To mitigate ground vibration, it is essential to develop a model to predict PPV. At present empirical models are used. These models are based on only a few input variables, hence they fail to take into account the effects of the myriad factors that cause ground vibration. Due to lack of explicit knowledge about the complex mine blasting system the scope of application of mathematical and statistical modeling techniques is limited. The artificial neural network (ANN) technique is a learning algorithm that can remove some of these limitations and can be applied to predict PPV. In this paper an ANN model is developed for prediction of blast vibration using 248 data records collected from three coal mines with diverse geomining conditions. The correlation coefficient between measured PPV and model output was found to be 0.96 and the average error percentage 11.85. The ANN model output was compared with the output of three empirical models that are widely used for prediction of PPV. The correlation coefficient between the PPV predicted by an empirical model and measured PPV data was 0.63 and the relative error percentage 38.47. This result demonstrates the superiority of the ANN model compared to empirical blast models. By using site-specific structural discontinuities as input the model performance can be further improved. Sensitivity analysis and 3D plotting were used to gain further knowledge about blast-induced ground vibration. IntroductionIn an opencast coal mine explosives are used for fragmentation of coal and overburden. If the explosive energy is not fully utilized it causes blast-induced ground vibration, which may damage nearby structures. Ground vibration is expressed as peak particle velocity (PPV). During different stages of mine planning and operation, it is necessary to use a ground vibration prediction model for blasthole design. Selection of the modelling technique is crucial. Mathematical and statistical modelling techniques have limited application because of the lack of explicit knowledge about the complex mine blasting system. Vogiatzi (2002) highlighted the problem of multicollinearity in case of statistical modeling techniques. Mutalib et al. (2013) stated that mathematical models are unable to capture the nonlinear relationship between several blasting-related parameters due to the complexity of the model input data. However, the difficulty involved in modelling complex blast vibration problems can be removed by adopting an alternative soft computing modelling approach. One of the soft computing techniques is the artificial neural network (ANN). Ragam and Nimaje (2018) developed an ANN model for predicting PPV using six input variables. Kosti et al. (2013) stated that the conventional predictors fail to provide acceptable prediction accuracy. They showed that a neural network model with four mine blast parameters as input could make significantly more accurate on-site predictions. Sayadi et al., (2013), using a database from Teheran Cement Company limestone mines, found that a neural network resulted in maximum accuracy and minimum error. Khandelwal and Singh (2009) developed an ANN model using 150 data records from an Indian coal mine with site-specific rock characteristics and geomining setting. Khandewal and Singh (2007) built a ground vibration prediction model for a magnesite mine using four prediction variables with 20 data records. Kamali and Ataei (2010) predicted PPV in the structure of the Karoun III power plant and dam using an ANN. El Hafiz et al. (2010) evaluated ground vibration predictors using data from a single-station seismograph at a limestone quarry in Egypt."

Feb 1, 2019

By A. Atta-Quayson

Since 2012, Ghana has been implementing local procurement regulations in the mining sector to broaden and deepen linkages between mining and other sectors of the economy. The regulations have been implemented in collaboration with the mining industry. This paper offers an in-depth analysis of how the local procurement regulations and related initiatives have been implemented so far. Primary data gathered with semi-structured interviews and secondary sources of data indicate a steady improvement in both in-country procurement and local manufacturing of inputs for the mining industry. There are, however, some challenges relating to tariff structure and support (financial and technical) for local suppliers and manufacturers to meet high standards and demands of the mining industry. This calls for a well-thought-out strategy and programme of activities to sustain and improve on progress made.

Feb 2, 2022

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magneto-hydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2014

By G. Asbjörnsson, E. Hulthén, P. Papadopoulou, C. M. Evertsson

Crushing plant managers need to assess, manage, and communicate the environmental impact induced by their crushing plant operations as a step towards the sustainable development of the company. However, performing reliable environmental impact calculations of crushing plants can be challenging when the availability of operational and emission data is low, and when the company’s environmental expertise is not adapted and connected to plant operations (or does not currently exist). To address these challenges, this paper proposes a practical approach where the lifecycle assessment methodology (LCA) is combined with process simulations in a web-based tool. To describe what functionality such a tool should have to be incorporated into a company’s workflow, the system that surrounds a crushing plant is analysed. Further, a case study with a three-stage crushing plant is introduced to showcase how the simulated power draw results produced with the beta version of the tool can be compared to measured sensor data from the crushing plant for one operational day. The results indicate that the simulation tool can provide an adequate estimation of the specific energy for the different material fractions and give an overview of the environmental impact of the process caused by electricity and explosives consumption. Plant managers and operators can use this tool to calculate the environmental impacts of their plant and simulate how different operational strategies influence them. Keywords: LCA, environmental impact, coarse comminution, crushing plant

Jan 1, 2020

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By S. Banisi, A. Ghasemi, E. Nematollahi

Discrete element method (DEM) has been used as a popular simulation method to verify designs by visualising how material will flow through complex equipment geometries. Although DEM simulation is a powerful design tool, finding a DEM model which includes real material properties (e.g., shape, cohesion and friction coefficients) is not computationally feasible. In order to obtain more realistic results, particle energy loss due to rolling friction has been highlighted by many researchers. To implement a reverse torque to account for rolling friction, various models have been proposed. On account of the complexity of the problem, there is no unique model for all applications (i.e. dynamic and pseudo-static regimes). In this paper, an in-house developed DEM software (KMPCDEM ©) was used to assess the robustness of three commonly used models by comparing the repose angle of iron ore pellets obtained through the draw down test in a laboratory setup and then the elastic–plastic spring dashpot model was modified based on considering the individual parameters instead of relative parameters of two contact entities. Results showed that the modified model could produce higher repose angle. The modified model was used to calibrate DEM simulation of repose angle of iron ore pellets in a laboratory setup of the draw down test. Comparison of the calibrated DEM simulation and laboratory results showed 2° differences between the predicted and measured angle of repose. This difference was attributed to considering the particle shape effects by assuming a spherical shape for particles. Keywords: DEM, rolling friction,particle shape, repose angle

Jan 1, 2020

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By F. Yang, S. S. Long

Mixed fatty acids, such as oxidised paraffin soap, are frequently used as a substitute for oleic acid in flotation of scheelite in China. Not only because it is cheaper than oleic acid, but also because it is superior in flotation performance to oleic acid. This superiority is generally attributed to the mixed fatty acids' synergistic effect. In this paper, the synergistic effect of oxidised paraffin soap was investigated. We found it mainly consists of a series of saturated fatty acid salts, with six to nineteen carbon atoms. All the contained fatty acids were classified into four groups based on their chain length to make the research work practical. Also, the groups were labelled as 1, 2, 3, and 4 in order. The research was simplified into studying the synergistic effect of four equivalent collectors, instead of fourteen fatty acids. It is justified by the fact that neighbouring fatty acids are expected to have a similar flotation performance. The synergistic effect of the four groups of fatty acids was studied by single-mineral flotation with single groups, binary mixtures, ternary mixtures, and the full component, as collector respectively. The flotation performance index and synergy value were introduced to evaluate flotation performance and synergistic effect of groups, respectively. The results show that the mixture 1+2+3 has the strongest synergy of all followed by the mixtures 1+3 and 2+3. The mixture 3+4 and 1+2, on the other hand, have negative synergy. The synergistic effect of mixtures of groups indicate that being consecutive in length and a broad range of lengths are vital for fatty acids to enhance synergy. Group 3 is fundamental for the collecting action of 733 oxidised paraffin soap in the flotation of scheelite. The fatty acid soap in group 4 is not suitable for flotation due to its low solubility. Keywords: Mixed collectors, synergistic effect, scheelite

Jan 1, 2020

By G. Mucsi, F. Kristály, R. Szabó

Kaolin is one of the most important ingredients in porcelain manufacturing. Its main phase is clay mineral containing aluminum hydrosilicate, namely kaolinite. Beside kaolinite it also contains quartz, illite and feldspars, which impair its applicability. Kaolin is a non-reactive material, but metakaolin can be produced by heat treatment (calcination) of kaolin, which is also used by the cement and concrete industry due to its latent hydraulic (pozzolanic) properties. Beside thermal activation, reactive materials can also be produced by mechanochemical activation in general. This paper deals with the mechanochemical activation of kaolin. The raw material was classified into various size fractions, then ground in a batch stirred media mill under varying circumstances (residence time, circumferential velocity). After grinding, the structural changes of the products were investigated by X-ray diffractometry (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). In addition, the particle size distribution of the ground material was determined by laser scattering. As a result of the grinding experiments and analytical measurements of the products, it can be clearly seen that reactivity of kaolin can be improved significantly by mechanical activation in a stirred media mill, but due to its high energy density the circumstances were optimised carefully to avoid aggregation. Keywords: Kaolin, grinding, stirred media mill, mechanical activation, material structure

Jan 1, 2020

By G. M. Evans, S. Mitra, A. V. Nguyen

As an alternative to the conventional flotation method, there has been continual research in an effort to enhance base metal ores and combustibles recovery using ultrasonics. These studies however were largely limited to the pre-treatment of ores for the removal of surface contaminants while the effect of ultrasonics on the bubble and pulp-phase interactions remained somewhat unexplored. Noting this deficiency, this study aimed to investigate the mechanistic effect of an ultrasonic field in an impeller less flotation cell specifically focusing on the bubble-particle interaction dynamics. A lab-scale flotation cell (capacity 1 litre) was designed, involving a vertically oriented ultrasonic probe (20 kHz, rated at 1.2 kW) and operated in the output power range from 1 to 20% with continuous liquid recirculation. Particle suspension was achieved by the combined action of recirculation and ultrasonic pulses. Interactions of coarse size glass ballotini particles (D32 = 314 μm) with bubbles (< 1 mm diameter) in the presence of a surfactant were studied, using high-speed imaging. Application of an ultrasonic pulse in the aqueous medium resulted in the generation of numerous microbubbles which increased with increasing input power and duration of the ultrasonic pulse time. Such periodic pulses introduced at a high level of turbulence in the pulp phase facilitated adequate bubble-particle contacts. Microbubbles played a key role in forming particle clusters which were observed to be floatable even in the absence of any carrier bubbles. When carrier bubbles were introduced, some of these particle clusters attached to the bubble surface and conveniently floated. It was noted that a favourable state of bubble-particle interaction was achievable to produce stable bubble-particles aggregates by suitably controlling the input power and period of the applied ultrasonic pulse. Keywords: Flotation, bubble-particle interactions, collision, attachment, detachment, ultrasonic pulse

Jan 1, 2020

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec&apos;s first diamond mine by 2013.

Jan 1, 2010

By J. P. Gouvea, T. R. Stacey

A research project was carried out on a gold mine in the Vaal River region of South Africa (Witwatersrand Basin) to evaluate the effect of two particular aspects of rockbolt installation – the angle of inclination of the bolt relative to the orientation of the rock surface, and the protruding length of the bolt – on the mine’s gully support system. A keyblock analysis approach indicated that these factors do not have an adverse impact on the stability of the strike gullies. This was confirmed by extensive empirical data collected from the case study mine. While safety is the primary concern, cost saving opportunities can be realized through reconsidering historically inherited support standards that are perceived to be correct and appropriate. The research described in this paper sets forth a practical approach, that is easy to implement and repeatable, to evaluate the role of rockbolts in stoping gullies.

Feb 12, 2024

By S. Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By Y. Makola, M. Kilumba, S. Mwaba, P. Ilunga, F. Banze, B. Nel, P. Kyoni, N. Mautsa, R. Nkomba, G. Ilu

Kamoto Copper Company is a copper cobalt mining company established in Lualaba Province of Democratic Republic of Congo under a Joint Venture between Glencore PLC and Gecamines (the state-owned mining company). Operations consist of underground and open pit mines, a concentrator producing sulfide concentrate and oxide ores milled slurry, and a hydrometallurgy plant producing copper cathode and cobalt hydroxides from concentrate and ores. The production capacity is 300 k/a of copper cathode and 35 kt/a of cobalt hydroxide. Since Q4 2020, the Luilu hydrometallurgy plant has experienced operational instabilities due to increase in proportion of dolomite in the ore mined and fed to the plant. This was diagnosed by the significant increase in calcium grade in ore and acid consumption, continuous foaming, and overflow of tanks with subsequent adverse impact on equipment availability due to corrosion caused by acidic spills, structure integrity, and safety concerns around the acidic slurry spills. Production was adversely impact due above equipment availability and often throughput restriction to mitigate the foaming and overflows. A high gangue-acid-consuming ore management programme was developed with the aim of mitigating these impacts. The programme included: (i) use of defoamer agent in leach to stop foaming and overflow, (ii) design of a mechanical solution to leach foaming and overflow, and (iii) froth flotation for copper and cobalt minerals separation from dolomite. Only option (i) is presented in this paper. Through laboratory testwork, pilot-plant testing, plant trial, and full plant implementation, Kamoto Copper successfully implemented a defoamer agent (Kemfoam X9980) dosing at leach, resulting in significant reduction in foaming and overflow of leach reactors and countercurrent decantation thickeners. The optimum defoamer dose rate obtained was 20 mg/L. Since then, the Luilu recovered its operational stability, the corrosion of critical equipment ceased, and availability improved as the acidic leach slurry spills ceased. The constraint on throughput due to leach foaming was addressed and the frequency of sliming events in the thickeners was significantly reduced as the foaming on the supernatant surface ceased, with subsequent significant reduction in interfacial crud in solvent extraction.

Jan 1, 2023

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

By I. Cameron, S. Ramjee, A. M. Garbers-Craig

The cause of reduced workability and increased ageing of a blast furnace taphole clay was examined. The investigated taphole clay contained 60 mass% alumina, with phenol-formaldehyde resole resin and liquid pitch serving as the binder system. The workability and Marshall extrusion pressure of the as-manufactured clay samples were evaluated to assess the extent of ageing of the clay. The wettability of all the raw materials was investigated to confirm compatibility between the dry raw materials and both the resin and liquid pitch, while the dry raw materials were analysed using XRF, XRD, and SEM-EDS. The characterisation of the resin and liquid pitch, as well as an analysis of their interaction, was performed using viscosity measurements, Fouriertransform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The analyses confirmed a chemical interaction between the resole resin and liquid pitch, where the chemical structure of the resole resin changed when mixed with pitch, preventing the typical curing behaviour of the resin. Upon ageing of the resin-pitch mixtures, the resin underwent premature cross-linking, causing the curing process to initiate at lower temperatures, i.e., earlier onset of curing. This premature cross-linking was likely due to secondary amines present in the liquid pitch, which acted as a catalyst for the curing process of the resin. This reduction in curing temperature after ageing was confirmed by an increase in binder viscosity, which was identified as the primary cause of reduced workability, accelerated ageing, and increased Marshall extrusion pressure of the taphole clay.

Jul 23, 2025

By C. Liu, G. Zhu, Y. Liao

"The effect of particle size on the flotation kinetics of a low-rank coal was compared using air bubbles and oily bubbles. Five kinetic models were applied to the data from the tests to derive the relationships between the flotation rate constant, the ultimate recovery, and the particle size fraction. The results show that oily bubble flotation (OBF) resulted in a lower ash content and higher combustible recovery than air bubble flotation (ABF), especially for the -125 ??m size fraction. It was found that the flotation of a low-rank coal in individual size fractions using air bubbles and oily bubbles can be best described by a first-order model with rectangular distribution of tendency to float and the classical first-order model respectively. OBF yielded higher ultimate combustible and ultimate ash recoveries. The flotation rate constants for OBF were higher in all the models except for the fully mixed reactor model. The ultimate recovery values and modified rate constants first increased and then decreased as the size fraction decreased. The trend of the flotation rate constants as a function of the size fraction was similar in all the models except for the fully mixed reactor model. IntroductionFroth flotation is a physical-chemical separation method that is widely used in coal beneficiation for the separation of fine coal particles from associated minerals in water slurries. Since the cumulative recovery of a component in the concentrate is proportional to flotation time, the flotation process can be considered as a time-rate recovery process (Emad, Mohammad, and Bahram, 2010). Therefore, the general mathematical flotation models that incorporate both a recovery and a rate function can describe flotation time recovery profiles.The kinetics of coal flotation, as a measure of coal recovery as a function of time, have been studied in detail by many researchers. Different kinetic models have been proposed and published in the literature. The order and the rate constant are strongly dependent on the flotation conditions, such as the particle size and size distribution, the bubble concentration, the reagent concentrations, and the operating parameters (Zhang et al., 2013). The particle size has been reported to affect the flotation kinetics to a great extent (Yoon, Luttrell, and Asmatulu, 2002; Ntengwe and Witika, 2011). Numerous researchers have studied the aspects of flotation kinetics while paying special attention to particle size (Meftuni and Ibrahim, 1997; Rubinstein and Samygin, 1998; Graeme, 2012). However, the effect of particle size on the flotation kinetics of a low-rank coal has been relatively little discussed."

Jan 1, 2017

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020