Search Documents

By D. F. Malan, P. J. Le Roux

Almost no work has been published on the strength of pillars in mines exploiting the LG6/LG6A chromitite bands in the Western Bushveld Complex. The strength of these pillars is unknown, and the hard rock industry still uses the Hedley and Grant formula. Numerical modelling, using inelastic constitutive models, may be of some value in estimating the pillar strength, but this approach is difficult and prone to errors as many assumptions are made. This paper explores the alternative approach of the back-analysis of actual LG6/LG6A mining layouts, using displacement discontinuity codes to simulate the average pillar stresses on a mine-wide scale. From this, and underground observations, a ‘minimum’ pillar strength (K-value in the pillar strength formula) can be estimated. The codes TEXAN and Map3D are both used in the paper to simulate the actual pillar shapes and sizes in an LG6/LG6A mine. The results are encouraging as the two codes produced similar APS values for a complex pillar geometry. An estimated K-value of 77 MPa was determined for the LG6/LG6A pillars in this particular area. This is more or less similar to earlier work done for the UG2 chromitite seam, but higher than the K-value of 39 MPa for a linear formula obtained by other workers for LG6/LG6A pillars. Caution should therefore be exercised before using this higher value for all areas. The effect of element sizes and explicitly simulating the effect of the surface for shallow pillars is illustrated in the manuscript using both codes. The need for actual pillar observations and an iterative design process, which cycles between modelling and observations, is also emphasized.

Nov 27, 2024

By H. Manurung, I. M. Bendiayasa, W. Astuti, and H. T. B. M. Petrus, F Anggara, K. C. Wanta

The leaching kinetics of cerium (Ce) and yttrium (Y) in sodium-hydroxide-digested non-magnetic coal fly ash using acetic acid were investigated. The variables analysed were pH, solid-to-liquid ratio (S/L), and temperature. The results show that cerium and yttrium's maximum recovery was 57.33% and 58.36%, respectively, under leaching temperature of 90°C for Ce and 60°C for Y at pH of 1,74 and 10 g/mL solid-liquid ratio in 240 minutes. Increasing the leaching time to more than 120 minutes did not significantly improve the results. After the magnetic separation process, the ICP-OES analysis shows a slight increase in the concentration of cerium and yttrium on nonmagnetic components. The XRD and ICP-OES analysis for the sample before and after silicate digestion shows that 40% silicate was dissolved. The calculation of apparent activation energies of leaching using the Arrhenius law for the leaching of cerium and yttrium gives 22.72 kJ/mol and 35.84 kJ/mol, respectively. The kinetic leaching model of cerium and yttrium all fit Dickinson's new shrinking core model. The calculation results show that the leaching reaction is controlled by combining interface transfer and diffusion across the product layer.

Nov 6, 2024

By C. Ntsele

Stirred milling technologies have firmly established themselves in concentrator circuits as energy-efficient alternatives to tumbling ball mills. High and continued increases in electricity costs, coupled with the ever-increasing power consumption by primary grinding circuits due to declining head grades of ore-bodies, provides a compelling case for these technologies. Additionally, the ability to successfully deploy stirred milling in coarse grinding applications extends the range of use in concentrators, thus increasing the opportunity matrix for energy optimization in a flowsheet. This paper therefore details methodologies and strategies that can be applied to evaluate the optimum stirred milling solution for different concentrator applications. These methods and strategies will focus specifically on the two major stirred mill machine types; namely, gravity-induced (VERTIMILL? grinding mill and Nippion-Eirich tower mill) and fluidized (SMD, Isamill?, Knelson-Deswik mill, etc. ). Finally, case studies from circuits across industry and laboratory tests will be used to illustrate the energy benefit from the use of stirred mills.

Jan 1, 2012

By J. Witley

"Narrow tabular platinum group element deposits in the Bushveld Complex of South Africa are typically evaluated by diamond core drilling from surface. Several short deflections are drilled from each mother hole in order to obtain multiple intersections at a close spacing (less than 1 m). Examination of the intersections from deflection drilling revealed the importance of these deflections in understanding the representivity of the borehole, obtaining an estimate of the nugget effect, and mitigating the undesirable effect of the high grade variability at the ultra-short range that is a characteristic of these deposits. The use of deflections in estimation was investigated by means of a number of techniques and scenarios in order to find the most appropriate way to use them in an estimate. A significantly improved level of confidence was gained from using multiple close-spaced intersections rather than a single borehole intersection. IntroductionThe Upper Group 2 chromitite layer (UG2 or UG2 Reef) is known for its remarkable geological continuity, being traced almost uninterrupted for tens of kilometres. However, what is often less well emphasized is the high variability in platinum group element (PGE) grade and thickness (and therefore PGE content) and internal reef stratigraphy over very short distances (several metres or even tens of centimetres).This paper examines the application of short drill-hole deflections in evaluating UG2 PGE mineral resources at Marikana in the western Bushveld Complex of South Africa."

Jan 1, 2017

By E. Matinde

Poor phase separation and fine dissemination of the desired components within congruous slag phases are key challenges limiting the recoverability of values from slags by conventional beneficiation methods. Slag microstructure conditioning is a pragmatic approach to increasing themvalue-in-use of discard slags, especially when integrated with the broader smelter infrastructure. Although not yet tested on oxide slag systems, this paper explores the potential application of magnetohydrodynamic principles to the crystallization behaviour of bulk slags. Integrating the slag microstructure conditioning infrastructure to the existing smelter infrastructure is key to unlocking the economic value of slags because it is most economic to condition the properties of molten slag directly after tapping. A new business model that integrates smelting units to transversalmeconomic activities, such as cement production and suppliers of construction aggregates, canmsignificantly increase the circularity of metallurgical slags.

Oct 9, 2024

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

By V. Jokovic

Hydrocyclones are the most commonly used classifiers in the mining industry. The reason for this is their low operating cost and a small footprint. Data from plant trials where screens replaced hydrocyclones indicated that lower bypass of fines and sharper separation could improve breakage rates, with a positive effect on flotation circuit performance throughput. Despite the importance of classification, hydrocyclones have not received as much attention as more expensive comminution units, and their technological progress has been incremental. Noticeable water split (Rf) reductions of a semi-inverted hydrocyclone have been reported in the past. According to theory, the hydrocyclone with reduced Rf will improve classification of fines. A classification study using semi-inverted hydrocyclones was conducted to determine if a hydrocyclone could be operated in a way that would minimise misclassified fines. The classification performance of a semi-inverted hydrocyclone will be presented in this paper and other potential applications will be discussed. Keywords: Semi-inverted hydrocyclone, water split, misclassification of fines

Jan 1, 2020

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

By G. B. Abaka-Wood, J. Addai-Mensah, W. Skinner

Recently, coal fly ash has become a potential candidate as a secondary resource of rare earth elements (REE). In this investigation, we studied the recovery of REE from fly ash from a commercial power plant. The specific aim was to assess the technical feasibility of recovering REE from the coal fly ash using conventional preconcentration methods, including gravity separation, magnetic separation, and froth flotation. The experimental results revealed that flotation achieved major gains in REE recovery and upgrading. However, during gravity and wet magnetic separation tests, the bulk of REE reported to the tailings. The results showed significant variations in the performance of the various beneficiation methods investigated. This study has confirmed that existing physical separation methods could be used to recover REE from coal fly ash prior to hydrometallurgical and pyrometallurgical processing, although some challenges persist.

Jan 2, 2022

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By I. O. Flores, A. Anani, H. Li

Current technological advancement has increased the exploitation of deeper ore bodies using underground methods. In certain cases, the mineral deposit starts near the surface and continues deep within the earth's crust. Such deposits are best mined with both underground and surface methods. Two main techniques are used to determine the optimal transition depth from surface to underground - a disintegrated approach and an integrated approach. Both methods have limitations in their use to determine the optimal transition depth. The objective of this research is to investigate the conditions in which an integrated approach to the transition depth problem is superior to a disintegrated approach. Three binary integer linear programming models are developed for this purpose: a surface and underground model for the disintegrated instance and an integrated model. A case study is performed to validate the models, with a comparative sensitivity analysis to obtain operational insights.

Sep 1, 2021

By A. J. H. Newell, K. Doherty

A copper-gold project has required a number of trade-off studies underpinned by test work to settle on pragmatic flowsheets and throughputs to support a pre-feasibility study that provides a compelling financial case. The primary trade-off studies were based on the mine schedule, ore type feed-grade recovery relationships, likely concentrate grades and typical marketing terms as well as the estimated capital and operating costs for a range of throughputs and mining strategies. Secondary trade-off studies were conducted for specific circuits and additional processing options. Although the details of these studies are not presented, the technical options and subsequent flowsheets are discussed. While the flowsheets will be optimised during the feasibility study stage, the basis is now fixed for the four ore types that would be mined from the copper-gold orebody. The ore types, resulting from a strong weathering profile, exhibit a wide range of copper mineralisation and gold associations, as well as gangue types. They display a range of characteristics that necessitated a nuanced approach to flowsheet development. The primary separation techniques that have been employed include gravity, classification, flotation and leaching while a range of comminution methods have been selected to suit the properties of the ore types. While technical issues are important factors in terms of maximising the quality of separations, recoveries and revenues, attention to material handling, equipment characteristics, the mine schedule, and capital and operating costs are equally important considerations for settling upon a suitable and robust flowsheet. Keywords: Flowsheet, testwork, studies, saprolite gold, native copper, chalcocite, chalcopyrite

Jan 1, 2020

By D. A. Cowen

Toll and custom treatment of base metal concentrates have been performed for decades as mines and concentrators are developed distant from capital and, energy-intensive smelting and refining facilities. Commercial treatment terms have been developed and refined for over a century, and are negotiated taking into account a complex array of quality and economic factors. Treatment of third-party concentrates in the South African platinum industry is a comparatively recent development, brought about by the opening up of mineral rights and operations being developed that are smaller than the critical size required to sustain capitalization of smelting or refining plant. Published commercial terms have not been demonstrated to reflect the complexities and subtleties of base metal concentrate markets. This paper outlines some key elements and parameter ranges of base metal concentrate treatment contracts, and applies similar principles to typical Merensky and UG2 platinum group element (PGE) concentrates to determine potential value distribution between the mining and treatment parties in tolling arrangements.

Jan 1, 2012

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By P. Fu, Y. Ma

Residual collectors and their byproducts (e.g., CS2) in flotation effluents can cause water contamination and even result in serious health hazards to humans and animals, Therefore, residual flotation reagents should be removed properly before discharge or recirculation into flotation circuits. In this work, four thiol collectors (potassium ethyl xanthate (EX), sodium diethyl dithiocarbamate (SN- 9), O-isopropyl-N-ethyl thionocarbamate (Z-200), dianilino dithiophoshoric acid (DDA)) were chosen as model pollutants. The collector removal, mineralisation and byproduct formation were compared by sole O3 and O3/UV185+254nm. The degradation rate constants of thiol collectors by O3/UV185+254nm were 2~6 times higher than those by sole O3. The mineralisation of collectors was also remarkably enhanced by O3/UV185+254nm. The degradation efficiency by O3/UV185+254nm had the order: EX>SN-9>>Z- 200>DDA. The Z-200 and DDA were refractory flotation reagents. The degradation of thiol collectors caused the reduction of solution pH and the increase of ORP and conductivity. However, the O3/UV185+254nm achieved more evident changes of these parameters than sole O3. During the degradation of thiol collectors, less than 4% of total sulfur in collectors was emitted into air as CS2 and H2S. Compared to sole O3, the O3/UV185+254nm had additionally included UV185+254nm photolysis and O3/UV254nm, resulting in higher efficiency in removing collectors. The O3/UV185+254nm was an effective process in treating mineral flotation wastewaters containing organic reagents. Keywords: Thiol collectors; flotation effluents; ozone; vacuum-UV; degradation, mineralisation

Jan 1, 2020

By J. A. Maritz, D. F. Malan

Pillar strength is affected by pillar shape, but this has largely been ignored in past research studies. Bord-and-pillar layouts are typically designed using empirical strength equations developed for square pillars. Owing to the poor quality of pillar cutting, many hard-rock pillars have an irregular shape and it is not clear how this affects pillar strength. Furthermore, the strength of rectangular pillars in comparison with square pillars is also difficult to quantify. The ‘perimeter rule’ is widely adopted for rectangular pillars, but its applicability for pillars with irregular shapes has never been tested. We used numerical modelling in this study to investigate the effect of pillar shape on strength. An analytical limit equilibrium model of a square and a strip pillar also provided useful insights. For slender pillars, the strength of a long rib pillar is essentially similar to that of a square pillar. In contrast, for rib pillars with a large width to height ratio, there is a substantial increase in strength. The study found that the perimeter rule should not be used for irregularly shaped pillars. Displacement discontinuity modelling, using a limit equilibrium approach, is proposed as an alternative to determine the strength of these pillars.

May 3, 2023

By J. Hadjigeorgiou, Y. Potvin

In a benchmarking paper published in the SAIMM Journal, Potvin and Hadjigeorgiou (2008) reviewed ground control strategies to manage large deformations in underground hard rock mines. Significant differences were identified in the design and acceptable tolerance between civil and mining engineering practice for squeezing ground conditions. Variations were also noted in ground support strategies between Australian and Canadian mines. In this paper we review progress in design methodology and ground support practice since 2008, including the availability of more effective deformation monitoring, new design tools, greater access to yielding ground support elements, and better installation practices. An improved understanding of technical and practical issues associated with squeezing conditions has led to the development of ground support guidelines for a range of squeezing ground conditions in hard rock mines.

Jul 5, 2023

By Z. Luo, W. Chen, Y. Zhao, Y. Fu, L. Dong

The gas-solid dense-phase fluidised bed includes a complex multiphase fluid-particle system; different complex exchanges significantly affect the stability of the fluidised bed. To elucidate the characteristics of fluidisation in a gas-solid dense-phase fluidised bed, this study used experimental performance tests to obtain the static density characteristics, and the attachment and flow characteristic of the dense medium. The results indicate that the bulk density of the dense medium increases first and then decreases with the increase of particle size. The airflow rate difference is used to quantify the wall attachment characteristics of dense medium and the average pressure gradient in the axial direction of the bed is approximately 20 Pa/mm under the fluidisation results. At the same settlement location, with the decrease of fluidisation number, the settlement velocity of large and small particles becomes slower, the boundaries of settlement displacement and location probability are gradually disrupted, and the falling velocity of particles with a radius of 20 mm is faster than that of materials with a radius of 15 mm. This work also established a theoretical basis for regulating the stability and separation characteristics of gas-solid dense-phase fluidised bed. Keywords: Fluidised bed, different size particles, fluidisation characteristics, flotation bubbles, settling motion

Jan 1, 2020