Search Documents

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock-dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Occupational noise-induced hearing loss continues to be one of the most pervasive health problems in the mining industry, despite over 25 years of regulation. One of the loudest pieces of equipment used in underground mining is the continuous mining machine. Noise sample data collected by the Mine Safety and Health Administration indicate that 42% of noise overexposures between 2000 and 2005 involved continuous mining machine operators. Previously conducted field and laboratory tests have determined that the continuous mining machine conveyor system is a dominant noise source. Loud impacts occur as the conveyor chain flight bars, used to move the mined aggregate, traverse their path from the top to the underside of the conveyor deck. Various noise control treatments have been applied to abate noise caused by the conveyor system. A durable polyurethane coating has been developed for the conveyor flight bars, resulting in a time-weighted average reduction of 3 dB(A) for an eight-hour work shift. In an attempt to further reduce continuous mining machine operator overexposures, a similar urethane coating has been applied to the tail roller component of the conveyor system. Laboratory results showed a 2 dB(A) reduction in sound power levels, but the component failed during underground durability testing. An outer steel sleeve has been added to the urethane coating of the tail roller to enhance wear resistance during mining. The urethane jacketed tail roller is the latest effort, combined with previous noise treatments, to bring the continuous mining machine into compliance with federal noise regulations.

By George A. Morgan

Output of minerals was insignificant in 1981 and made a negligible contribution to the gross national product (GNP), estimated at $1.2 billion.2 Agriculture accounted for 40% of CNP and manufacturing accounted for 10%. The chief source of income was indirect taxes levied on traffic through the Port of Cotonou, an entrepôt. Trade statistics for Benin were incomplete and dated. Major trading partners were France and other members of the European Communities. Benin was a member of the West African Monetary Union and as such must coordinate its foreign currency, reserves, interest rate structure, and fund transfer with other member countries. Its currency, the Communauté Financière Africaine franc (CFAF), was fixed to the French franc.

Jan 1, 1983

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By H. B. Carroll

The performance of commercially available portable instrumentation for detecting nitrogen dioxide, sulfur dioxide, and hydrogen sulfide was evaluated. Length-of-stain detector tubes from several manufacturers were included in the study. The instruments were evaluated in atmospheres with 50-and 80-percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the threshold limit values. The results from the gas analyzers were correlated with the known contaminant concentration by calculating and plotting an estimated line of regression, confidence limits, and correlation coefficient for each detector system. An increase in the relative humidity from 50 to 80 percent at /5° F changed the instrument response to the contaminants. The uncertainties in detection precision reported are for the observer-instrument system. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than from a predominant difference in the tubes.

Jan 1, 1975

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974

By W. H. Tomlinson

This publication presents the basic text for a 20-hour accident-prevention training course developed for supervisors by the Federal Bureau of Mines. During the past 2 years, the course has been used by the Bureau in teaching more than 300 groups of coal-mine supervisors-men whose responsibility is twofold: To manage in production and maintenance phases of coal mining and to guide their men along paths of safety. This is a handbook for teaching teachers. In this handbook will be found references to safety practices followed by companies that consistently have low accident records. These companies credit their outstanding performance to the adoption and faithful observance of accident prevention by supervisors and workers alike on a wholesome, cooperative basis. Teaching safety to workers involves both on-the-job and classroom-type instruction. If such training is to be permanently effective, it must be reinforced consistently on the job by the immediate supervisor of the worker. This publication is intended to provide such a supervisor with the motivation to provide such follow-up and shows how he can accomplish it effectively.

Jan 1, 1962

By Verne E. Hooker

Near-surface temperature measurements in two granite quarries show that diurnal temperature variations are significant to a depth of 1 or 2 feet, and annual temperature variations are significant to a depth of at least 25 feet. As a result, ground stress anomalies due to temperature exist near the surface, and their magnitude depends upon the time of day and the time of year. Rock stress and corresponding temperature measurements were made in one granite quarry over a rock temperature range of 33° to 81° F. Measured rock temperatures show good agreement with values predicted from one-dimensional heat flow theory. Calculated and measured stress-temperature coefficients for the two granites in this study are given. Thermally induced stress variations in near-surface rocks tested were as large as 1,690 psi from combined daily and seasonal temperature changes.

Jan 1, 1971

By L. W. Brandt

The Bureau of Mines, as part of its mission to effect pollution abatement, conducted research to study various means of dewatering Florida phosphatic clay wastes and reclaiming mined lands. The work was done in cooperation with 10 Florida phosphate companies. During this work, a novel technique to effectively dewater phosphatic clay wastes was developed. The solids contained in the clay waste slurry are slowly compressed by moving wire mesh screens through the system. In a typical application, the screens were moved downward, compressing solids ahead of the screens. The rate of movement of the screens is an important variable in the process. It is believed that the moving screens distort the gel structure of the phosphatic clay system and cause the release of water. Samples of 18 clay wastes, including a high-grade attapulgite from beneficiation plants of the Florida phosphate field, were studied using the method. Typical samples were concentrated from initial solids of 4.7 and 11.9 percent to 16.8 and 25.2 percent, respectively, in 3-1/2 days. The high-grade attapulgite sample was dewatered from 2.7 percent solids to 13 percent solids in the same period.

Jan 1, 1980

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By L. A. Haas

In this Bureau of Mines investigation, conditions were determined to form an iron sulfide adherent coating with a metallic golden luster on steel upon anaerobic heat treatment with sulfur. The sulfide formation rate was determined in the temperature range of 105° to 500° C with reaction times up to 68 hours. The optimum temperature and time to form an adhering decorative coating on mild steel was in the range of 105° C for about 70 hours to 285° C for 1 hour. The golden coating consisted of an inner layer of pyrrhotite and an outer layer of pyrite. At temperatures higher than about 300° C, the outer layer thickness decreased owing to the decomposition of pyrite to pyrrhotite.. Small quantities (<0.5 wt-pct) of petroleum oil accelerated the sulfide growth rate. The sulfide coating decreased the corrosion rate of steel in a neutral aqueous medium by a factor of two. The dissolution of pyrite in water was dependent on particle size and surface area with the flat pyrite coatings exhibiting the lowest dissolution rate.

Jan 1, 1974

By E. R. Maize

This report is the second of a series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company&apos;s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By E. R. Maize

This report is t e second of s series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company?s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa, This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

Reduce the cost of modifying uranium well casings so that leaching solutions can pass through, but sand grains are blocked. Approach The well casing and surrounding cement are perforated at the mineralized zone by impinging them with high pressure water jets. How It Works A nozzle assembly is attached to a high pressure (15,000 psi) pipe and lowered into the well casing which typically is schedule 40 PVC (poly-vinyl chloride). The high pressure pipe line is extended down Into the casing until it reaches the mineralized zone. The upper end of the pipeline is then connected by a high pressure hose to the outlet of a 10,000 psi pump. Turning the pump on for 5 seconds causes a high velocity water jet to cut through the well casing and the surrounding cement. Figure 1 shows a high pressure pipe being installed in a well casing. Cutting small diameter holes in the casing allows the leachant to enter the casing and be pumped to the surface. However, the holes are small enough to prevent most sand grains from entering. Numerous holes are usually cut through the casing. The 3-nozzle assembly shown in Figure 2 cuts three holes, one above another.

Jan 1, 1978

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC&apos;s) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC&apos;s in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973