Search Documents

By M. H. Stanczyk, I. L. Feld

Dewatering of typical Florida phosphate rock slime by electro - osmotic techniques was investigated to determine if a compacted , plastic solid product could be obtained with simultaneous recovery of the water for re - use . Tests with porous cathodes and rod - type anodes imbedded in dilute slime charges of up to 4 tons in weight showed that the slime could be dewatered to about 35 percent solids . The dewatered products had the consistency of modeling clay . In the large - scale tests using 2.5 - foot electrode spacings , about 21 kilowatthours of power were consumed per ton of water removed in thickening the slime from 17 to 25 percent solids , but the rate of water removal was so slow that the process was not considered commercially feasible . Other tests made with electrode spacings of from 2.5 to 8 feet showed that more rapid dewatering could be obtained but that the power required was excessive . However , for special uses such as stabilizing slime pond dikes where the cost of dewatering might not be a prime requisite , high voltages could be used to rapidly remove the water . Tests of 400 - pound slime charges using a combination of electroosmosis and vacuum filtration showed that the rate of dewatering could be expedited . The average power required to thicken a ton of slime from 15 to 35 percent solids was 5 and 50 kilowatt - hours when operating the electroosmotic filtration cell at potentials of 20 and 100 volts , respectively . calculated filtration area of about 10 square feet per ton of slime treated per day was required to thicken the slime from 15 to 35 percent solids .

Jan 1, 1964

By Jr. Boyle

This report analyzes the availability of chromium in the form of ferroalloy products (high-carbon and low-carbon ferrochromium and ferrochromium-silicon) and chromite products (metallurgical, chemical, refractory, and foundry sands) in market economy countries (MEC's). A total of 873.5 Mmt of in situ material, containing 202.5 Mmt of chromium, in 10 MEC countries was analyzed for availability as of the January 1989 study date. Extraction and beneficiation of this in situ material would result in 475.4 Mmt of marketable chromite products. As analyzed, 288.5 Mmt of these chromite products would be available for export or for internal chemical and refractory use and 186.9 Mmt would be smelted in-country to produce 74.3 Mmt of high-carbon ferrochromium, 3.9 Mmt of low-carbon ferrochromium, and 2.0 Mmt of ferrochromium-silicon, all available for export. A network flow model, which includes centrally planned economy countries (CPEC's), was also constructed to analyze world chromium supply and demand interactions for the period 1986 through 1994 and to address a hypothetical North American embargo on direct imports of all South African chromium products beginning in mid-1990. The model shows capacity constraints developing in the MEC high-carbon ferro chromium industry in 1987 and a possible subsequent overreaction by the industry in terms of new capacity additions. The results suggest that sufficient chromium is available to North America should an embargo on direct imports from South Africa be imposed by its governments. However, the effect on export revenues in South Africa is relatively small, and timely increases to world ferrochromium, chemical chromite, and foundry sand chromite capacities would be required.

Jan 1, 1993

By Carl Rampacek, W. A. McKinney

The feasibility of leaching calcareous and siliceous oxidized copper ores by downward percolation with dilute acid was investigated in the laboratory and in a small continuous plant operated by the Federal Bureau of Mines . The crushed ore was leached in deep columns with solutions containing 1 or 5 percent sulfuric acid to dissolve the oxidized copper . Bench - scale laboratory tests on two calcareous ores from the same deposit indicated that a maximum copper extraction , about 72 percent , could be expected from heap leaching a feed as coarse as 1 inch . Laboratory tests on a siliceous ore showed that almost 70 percent of the copper could be extracted by leaching a 1 / 4 - inch feed . The bench - scale tests were supplemented by larger continuous runs wherein the copper was recovered from the leach liquors by precipitation on detinned scrap iron . Leaching the calcareous ore for approximately 10 days recovered 62 percent of the total copper . The sulfuric acid consumption was 9.6 pounds per pound of copper recovered . Treatment of the siliceous ore recovered 62.5 percent of the total copper in a 2.5 - day leach and the acid consumption was 3.7 pounds per pound of copper recovered . Cement copper products that assayed over 71 percent copper were obtained from the leach solutions by precipitation on scrap iron . The bench - scale and continuous tests demonstrated that downward percolation leaching of the calcareous ores was technically feasible but not economically practicable because of high acid consumption by the gangue . Leaching of the siliceous ore was rapid and the acid and water requirements were nominal . The downward percolation leach procedure is simple and requires a minimum of plant equipment .

Jul 1, 1960

By Kung-Lee Wang

The 1963 performance of the United States economy was impressive. The year was one of continued growth unmarred by a recession. By the end of 1963 the economy's expansion had already lasted almost as long as the 1954-57 upswing, and the net gain in output since the trough in activity in early 1961 compared favorably with most earlier postwar cyclical advances. There was no indication of any slow- down at yearend. Both gross national product (GNP) and national income in 1963 were 5 percent higher than in the previous year. GNP totaled $584 billion, a gain of $28 billion over 1962. Real output of goods and services rose 3.4 percent over the year. Price increases continued to be moderate. Production, employment, personal income, and corporate profits all registered new but unemployment continued high at 5.5 percent and the prospects for improvement remained poor. The economy again failed to use its full potential. Current value of mineral production kept pace with the economy. The constant dollar value of mineral production gained more than real GNP because of the relatively stable price of minerals. Mining production achieved a new high in 1963. Steel production totaled 110 million tons, 12 million tons above 1962, making 1963 the first 100- million-ton year since 1957 and lifting the steel-associated minerals group upward. The gain in ferrous metals mining was insufficient to compensate for the decline of nonferrous metals mining resulting in an insignificant decline in the metal mining total as a whole. The upsurge of construction material minerals output, with an assist from chemical and fertilizer minerals, accounted for peak production of

Jan 1, 1964

By Charles L. Kimbell

Annual global steel industry investment is partly mirrored in the data for selected market economy countries that appear in table 13 for 1988-90. No reasonably comprehensive 1991 data were available for inclusion in this study, and the partial reporting available was so incomplete that it was impossible to demonstrate whether the level advanced or declined from the 1990 level of nearly $15.5 billion. Moreover, with the radical changes that are now being effected in the steel industries of the states that were the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available. Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area has been included in table 14, and it is evident that there was a substantial upturn in investment in 1991. The level of almost $74.5 billion was 14.5 % above the 1990 level and included gains in every topical category and geographic area. The source of information for this table has been changed to the Oil and Gas Journal Database from the previously used Chase-Manhattan Bank study of Capital Investments of the World Petroleum Industry, which has been discontinued. Because of this source change, it has been necessary to modify the structure of the table somewhat, but its total scope of coverage is regarded as basically unchanged. It should be noted that the grand total, as well as some of the detail appearing for 1987, corresponds precisely with those in the previous source.

Jan 1, 1993

By L. A. Haas

The feasibility of removing sulfur dioxide by carbon monoxide reduction in a fixed-bed catalytic reactor was investigated by the Bureau of Mines. The reduction rate of sulfur dioxide with carbon monoxide was significantly dependent upon the iron and alumina content of the mixed catalyst. Maximum catalytic activity was obtained with about 40 percent iron-alumina mixture with a nominal gas mixture of 10 percent carbon monoxide, 5 percent sulfur dioxide, and the balance nitrogen. The synergistic effect of this catalyst mixture was explained by a dual reaction site mechanism, with both iron and alumina augmenting their specific sites at their interparticle contacts. The catalytic activity also increased with decreasing catalyst pellet size. With O.7-mm pellets, the entire pellet appeared to be catalytically active in a 2-gram catalyst bed. The apparent activation energy of the reaction was 18.3 kcal per mole in the temperature range of 350° to 600° C. Carbonyl sulfide (COS) was produced by the interaction of carbon monoxide and sulfur. The amount decreased with decreasing CO concentration. The ratio of COS formed per SO2 removed reached a maximum at about 400° C. The reaction rate appeared to be independent of S02 concentration in the range of 0.2 to 16 percent. The rate, however, increased directly with the CO concentration in the range of 5 to 20 percent. The presence of CO2 (<15 percent) had no appreciable effect on the rate. However, not over 0.5 percent oxygen could be tolerated. This method appears feasible for removing S02 from waste gas if the oxygen is removed prior to the catalytic S02 reduction process.

Jan 1, 1971

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By A. R. T. Denues, A. P. Rowles

"INTRODUCTION Summarized data developed by J. E. Crawshaw and E.J. Murphy, 4/of the Explosives Division of the Bureau of Mines, suggesting marked variations in oxygen condition in three permissible explosives, have been reported 5/. Such variation is of interest in other work, it having been shown, for example, that the oxygen condition may have marked effect upon the products 3/ and the propulsive strength 7/ of explosives. It seemed that a more detailed presentation and more usual statistical analysis of these data might be of considerable general interest and not complemented in the literature.This report presents both the original data developed by Crawshaw and Murphy and the results of a simplified but seemingly acceptable statistical analysis of these data. The logical ground for this analysis might seem somewhat questionable because of the lack of systematic information concerning the extent of errors in the analytical procedure but the data show that there are several cogent and seemingly unequivocal indications of real heterogeneity in the explosives."

Jun 1, 1942

By John S. Hutchins

Two potential modified in situ methods are described for recovering the 68% "unrecoverable" hydrocarbons in oil reservoirs. For the 300 billion barrels of conventional light crude a Drip Drainage system is suggested by mining underneath a reservoir and producing from below by controlled gravity flow. For the 200 billion barrels of heavy or viscous oil and tar sands deposits a Flip Flop process is described using surface flooding with hot water saturated with surfactant and weighting additives. Mining engineering description of shafts and tunnels required are included as is discussion of the tunnel proximity to a reservoir. Petroleum engineering flow equations to describe production rates and candidate reserve areas of the U.S. are described. DCF economics are provided to indicate that current oil prices may be sufficient to commercially develop these recovery methods.

Jan 1, 1978

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By D. Harrington

The Bureau of Mines was created in 1910 largely to determine methods of preventing coal-mine explosions; the Bureau&apos;s studies have proved that coal dust, except possibly that of some grates of anthracite, can initiate an explosion in the absence of gas and that its ability to extend or propagate an explosion of either gas or dust has been responsible for nearly all of the widespread explosions that have taken place in bituminous and other nonanthracite mines in the United States in the present century. It is believed by many persons that all atmospheric dusts may be harmful if breathed in large enough quantities for long enough time; bituminous coal dust is generally considered to be essentially harmless physiologically, yet there is abundant evidence of definite damage from inhalation of bituminous dust mixed or unmixed with the dust of other materials. Attention un¬questionably should be given to allaying dust in bituminous mines, especially at principal dust-producing sources. This publication enumerates some of the sources of dust and describes practical methods of employing water as one of the most effective of the known methods to allay dust in bituminous mines.

Jan 1, 1938

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By A. C. Johnson, es Hol, E. O. Binyon

"INTRODUCTION AND SUMMARYThe tungsten properties of Lincoln Mines, Inc., and North Tem Flute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co.Claims leased by the Lincoln Mines, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57 E.: and sec. 1, T. 4 S., R 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc. and general offices are in the Wesley Temple Building, Minneapolis, Minn.In June 1945, the Atolia Mining Co. leased the property and purchased the mill and mining equipment from Lincoln Mines, Inc. P. R. Bradley is president of the Atolia Mining Co., whose offices are in the Crocker Building, San Francisco, Calif. This company surrendered the lease on the property on September 30, 1948. The property owners are continuing operations and are now engaged in building a 20-ton mill.The claims of the North Tern Flute Mining & Development Cc. are in sec. 1, T. 4 S., R. 56 E., M. D. B. & M. Merle F. Schofield is president of the company and maintains an office at Hike, Nev. These claims were leased by H. P. Laslett, of the Utah Nevada Mining Co., in 1945 and by the Atolia Mining Co. in 1946. The owners are now doing some exploratory work."

Jan 1, 1950

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining ( 1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and ( 3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By G. L. Oldright

This paper is the second of a series that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. The writers wish to express their appreciation to the management of the International Smelting Company at Tooele. Utah, for their kind cooperation which made possible the assembling of these data.

Jan 1, 1929

By A. Aly Selim

This report describes the feasibility of predicting percussive drilling rates by equations derived from statistical regression analysis. The least squares statistical method was used and the analysis was performed both by direct and by stepwise linear regression analysis. The predicted penetration rate is a function of the drill power and the physical properties of the rocks penetrated. The results show promise that the technique may be of value in providing a mathematical model by which percussive drill manufacturers and users can predict the performance of a given drill. Experimental work involved two mining type percussive drills. Penetration data for these drills were determined from nine rocks drilled in the laboratory. Drill work rates (power) were determined in a separate series of experiments. Rock physical properties were measured from diamond-drill core samples taken from the same blocks used for percussive drilling.

Jan 1, 1970

By R. L. Brown

This report is the 18th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations. The previous 17 reports have covered fiscal years, but this report covers not only the fiscal year from July 1, 1952, to June 30, 1953, but also July through December 1953, to bring the report to a calendar-year basis. Most of the material in this report relates to publications issued during the reporting period, Some work is mentioned briefly on which publications have not yet been issued or on which data are riot expected to be published, for security or other reasons, and in a few instances publications issues before the reporting period but not included in the previous report are mentioned.3/ Further details on the published work described herein may be found by referring to the publications cited in the footnotes. During the reporting period, the Bureau directed its research and technologic work on coal toward developing end encouraging increased conservation and more efficient use of our mineral fuel resources through more efficient and safer mining methods and improved methods of preparing and utilizing these fuels. Some significant advances, particularly in coal-mine safety, mining methods, and development and utilization of low-rank coma have been made.

Jan 1, 1954

By J. P. Capp

The Federal Bureau of Mines and the Alabama Power Company conducted an experiment in underground gasification of coal at Gorgas, Ala. involving the use of hydraulic fracturing to increase the air acceptance of a coalbed for the introduction of combustion air and removal of product gases. Air acceptance is defined as the flow rate of air which can be injected into the coalbed at 65 p.s.i.g. This was the second time the hydraulic-fracturing technique was used at Gorgas. Sand suspended in a heavy oil served as the fracturing fluid in the first experiment; in the second the sand was two to six times larger and was suspended in a water-starch gel. In addition to providing further tests of the underground-gasification process, the purpose of the second experiment was to determine the effects of the larger sand and greater volumes of a water-base fluid on (1) the extent of the fractured area, (2) the air acceptance of the coal, and (3) the rate at which a gasification path could be carbonized (linked) through the coal, and to compare these results with those of the first experiment. The coal was fractured by injecting 11,000 lb. of sand and 33,580 gal. of water and water-gel at 200 to 600 g.p.m. and 900 to 1,000 p.s.i. The fluid fractured the coal and the sand served as a propping agent to hold the cracks and crevices open. Pressures during the fracturing operation at test boreholes indicated that the fracturing fluid extended only about 150 ft. from borehole H, the point of application of the fracture. Injection of air revealed that the air acceptance of the coalbed within this e t was materially increased. On the other hand, increased air acceptance also was noted at boreholes up to 280 ft. from borehole H and at the electrolinking area 300 to 400 ft. away, indicating that the fracture effects extended considerably farther than was evident from observation. Similar effects were noted at approximately the same distances after the first hydraulic fracture.

Jan 1, 1961

By Fay B. Dillard

This Bureau of Mines report reviews the disposition of natural gas as delivered to industrial consumers via main line sales. Salient information on main line, or direct, natural gas sales to industrial users is presented by State) standard industrial classification code (SIC) revenue, and type of sales for the years 1968 through 1973.

Jan 1, 1975

By E. D. Wilson

A study of factors related to subsidence was specified in a project proposal entitled "Structural Analysis of Block-Caving Operation, San Manuel Copper Mine, Pinal County, Ariz.," approved by the Bureau of Mines early in 1953. This proposal was designed by Charles H. Johnson, then chief of the Base Metals Branch of the Minerals Division, Washington, D. C., assisted by Dr. Leonard Obert, chief of the Applied Physics Branch, Region VIII (now Region V), College Park, Md., and E. D. Gardner, chief mining engineer, Bureau of Mines, Washington, D. C. It read as follows: This project is a study of the mechanics of undercut block caving in a deep ore deposit. The San Manuel is a low-grade disseminated copper deposit containing nearly a half billion tons of ore lying at depths of 500 to 2,000 feet. Development is just starting. Production is to begin in 3 to 4 years (in 1956) at a rate of 30,000 tons of ore a day, or 60,000 tons of copper a year. A Government loan of $90,000,000 /subsequently increased to $94,000,000/ and a long-term Government purchase contract support the capital investment, which will total about $110,000,000.

Jan 1, 1957