Search Documents

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By I. R. Hanby

A simple solution to the problem of whether to round the calculated number of trucks up or down to the nearest whole number is to adopt as criterion the minimum cost per unit volume/mass moved, assuming all trucks in the fleet are of the same type. When the effects on journey time of varying haul-road slope are calculated for several rolling resistances, it is shown that the optimum angle of 7.5 degrees is moderately independent of both rolling resistance and height climbed; the lower the resistance, the lower the sensitivity to ramp angle, but if haul-road gradients do not exceed 1 in 10 (5.7 degrees) for safety reasons then travelling time will never be more than 7% greater than its theoretical minimum. Further calculations result in a graph of the maximum payload values to incur the minimum cost, for different values of total effective resistance

Jan 1, 1991

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By G. S. Camm

Gwynfynydd is a small, high-grade black shale-hosted vein-gold deposit. The Chidlaw Link Zone is the only area being mined and contains 24 000 t ore grading 15.2 g/t gold. Within the Link Zone a complex vein structure occurs consisting of a mother vein up to 5 m thick and narrow (less than 0.5 m) leader veins. The former shows minor variations in dip, strike and thickness, whereas the latter show marked changes in all three. The leader veins are hosted within the footwall zone of the mother vein and both are composed of quartz with galena, sphalerite, chalcopyrite, pyrite and minor arsenopyrite. The vein system is transected by a series of cross-vein and intra-vein dip-slip faults. Pockets of gold occur at vein intersections or branches and within the complex footwall zone and are often related to variations in vein attitude and/or geometry. The Chidlaw Link Zone displays a complex, erratic distribution of gold mineralisation and a multi-stage history of structural activity, fluid flow and mineral deposition

Jun 18, 1905

By S. G. Tsimas, A. K. Moutsatsou, G. K. Parissakis, M. A. Komiotou

For Greek kaolin producers, a considerable proportion of whose output is from deposits containing more than 4 wt% Fe2O3, the colouring resulting from iron oxide impurity represents a serious problem that necessitates upgrading of the ore to meet commercial specifications. Autoclave leaching with oxalic acid for 1 h at 120 degrees C and 5-6 bar was shown to reduce Fe2O3 by up to 90% without affecting the structure of the kaolin, which maintained its physicochemical properties. The iron oxalate product can either be removed from solution or precipitated as iron hydroxide with recycling of the oxalic acid

Aug 1, 1995

By A. D. Fowler, M. T. Anderson

A phenomenological model is presented that relates Pb-Zn mineralisation to proximal geopressure zones. Typically, geopressure zones (GPZ) consist of masses of undercompacted sediment encapsulated within impermeable shales and are characterised by high formation fluid pressures. Heat flow is perturbed in some GPZ on account of their insulating properties. Geothermal gradients as high as 150 degrees C/km have been observed over short distances in the sediments of the US coast of the Gulf of Mexico. Some modern geopressure zones are known to reach temperatures of 120-150 degrees C at depths of 2.5-3.5 km. It is demonstrated that the zones may act as proximal sources of hydrothermal fluids, thus explaining the high temperatures of mineralisation observed in the deposits, which are hosted in basins characterised by thick, rapidly deposited, shale-rich clastic sequences

Jan 1, 1991

By M. Foguenne, A. van Lierde, P. Henry

Leaching experiments were carried out on a spent catalyst sample with a honeycomb structure, containing 47.5% Ti, 5.8% Mo, 2.7% Si, 2 035 ppm As, 52 ppm Pb and 8.8 ppm Hg. More than 93% of the Mo and As was removed by direct alkaline leaching after grinding to 80% -36 micrometres. The residue contained 0.3% Mo and 60 ppm As. To obtain a TiO2 matrix with 30 ppm As, acid leaching at controlled pH with 90 kg/t Al scrap was followed by oxidising alkaline leaching. Treatment of the direct alkaline leach solution or of the mixed solutions from the two-stage process involved two successive operations: purification by neutralisation with Al(OH)3 addition to raise the Al concentration to 4 g/l, and ion exchange on Amberlite IRA 94 S resin. Whatever the type of solution treated, elution with 200 g/l NH4OH solution gave an eluate of very high purity containing 164 g/l Mo, less than 70 mg/l V and less than 2 mg/l As

Jun 19, 1905

By J. A. Every-Brown

Case studies are presented of three derelict sites in Kent and Essex that provide a good cross-section of opportunities for second-generation commercial uses of former chalk, limestone, clay and gravel workings. A 240 ha abandoned chalk quarry at Grays in Essex, now known as Chafford Hundred, is undergoing mixed development to include leisure facilities, a range of housing and commercial areas and an enhanced environment. The 120 ha of Stone Marshes now comprises the Crossways business park and the Dartford international ferry terminal. Reclamation and servicing required more work than had been anticipated and the fact that the area was within the green belt added to the delays, but Blue Circle was eventually able to provide a comprehensive development of the entire area to a high environmental standard. Stone Pit 1 landfill, at Dartford in Kent, is a former chalk quarry 40 ha in area and with an original average depth of 35 m. Landfilling commenced in 1976 and during the period 1979-1984 the site operator designed, developed and installed a gas collection and flaring system. From 1986 a gas plant supplied up to 5 000 000 therm/yr of landfill gas to a local cement works and in 1989 a 1 MW power generation scheme, later expanded to 3 MW, was commissioned. Gas is currently also supplied to a metal refining company for use in internal combustion engines

Aug 1, 1994

By C. J. A. Mcewan, C. M. Rice

The Rosita Hills contain rich, vein- and breccia pipe-hosted precious metal deposits. Volcanic activity occurred in two cycles - an early, mainly andesitic cone-building phase that terminated in the formation of a caldera and breccia pipes and a later phase characterised by trachytic lavas and dykes, rhyolite domes and lamprophyre dykes. Alteration consists of weak propylitic and argillic and, locally, intense advanced argillic, K-feldspar sericitic and silicic types. Marked trace-element depletions (Rb, Sr, Zn, Mn) are associated with K-feldspar-sericitic alteration and with advanced argillic alterations, whereas enrichments (Pb, Ag) are associated with K-feldspar-sericitic alteration. Gold distribution is highly localised and is controlled by breccia pipes and a caldera ring fault; it is not related to district scale alteration. In general, the geochemical and alteration patterns are complex, but they are clearly influenced by linear structures, the caldera ring fault and breccia pipes. Pipe-hosted Au-Ag and vein-hosted Ag mineralisation are associated, respectively, with early andesitic and late, post-caldera rhyolitic activity. The pipe-hosted and, especially, the vein-hosted mineralisation show affinities with adularia-sericite-type epithermal deposits

Jan 1, 1991

By A. R. Biggart

Twenty-sixth Sir Julius Wernher memorial lecture, presented at the Tunnelling '94 symposium held in London, 5-7 July 1994. In describing 18 projects with which he has been involved over a period of 36 years, the author aims to illustrate how technological change and an increase in scientific knowledge have influenced tunnelling practice, which he nevertheless maintains does continue to be an art. Tunnels discussed are: the Silver Street, Blackfriars, Whitechapel, St. Paul's and Waterloo Post Office tunnels, 1958-1969; metro tunnels on the Victoria Line, London, 1962-1970; the introduction of tunnel boring machines (TBMs), 1971-1978, in the Empingham reservoir diversion tunnels in Rutland, the bentonite tunnelling machine experiment at New Cross, the Southern tunnel water main section of the London Ring Main and the Warrington sewer in Cheshire; tunnels in rock 1975-1981, for the Lune Wyre and Megget Manor aquaducts, Weymouth sea outfall and Bristol interceptor sewer; Priestley TBM tunnels 1969-1982; the Greater Cairo wastewater project 1983-1987; Anacostia River crossing, Washington DC 1985-1987; the Channel Tunnel 1987-1992; and the Storebaelt eastern tunnel in Denmark, 1992-1994.

Dec 1, 1994

By T. Lenarcic, R. Svrkota, J. M. McNeal, E. Prohic, S. Pirc

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Surface drainage samples, the usual media employed in mapping national territories, cannot be used for the geochemical mapping of carbonate terrains because there is no regular surface-drainage pattern on karst. Suitable sampling media have been studied in Yugoslavia, one-third of which consists of karst terrain. Sampling designs for the work were based on analysis of variance techniques. During initial investigations of various sampling materials in NW Yugoslavia sediment and aquatic moss from karst springs, along with soil, were established as the most appropriate media. Modified sampling procedures were then carefully applied along the entire Yugoslav karst belt, which includes terrains of contrasting topography, climate, pedology and vegetation. The studies indicate that climate and relief do not systematically influence the geochemical composition of soil. Regional and local variability was assessed for 21 chemical elements and the feasibility of producing stable regional geochemical maps was determined for a number of elements on the basis of sampling aquatic moss and sediment from karst springs and soil

Jul 1, 1991

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

By D. C. Bailey, D. I. Hodson

Paper presented at the annual joint meeting of the IMM and IMinE held in Harrogate, 31 January 1991. The Neves-Corvo copper-tin mine is the highest-grade large-tonnage copper operation in the world and is now arguably the most significant producing base-metal mine in Europe, rating in the top ten world producers of both copper and tin. A description is given of the initial exploration work and the development of the project from the orebody discovery in the Iberian Pyrite Belt of southern Portugal in 1977 to full operating capacity in 1990. The chronological account includes discussion of the main organisational, financial, technical and environmental decisions and of the various difficulties encountered, and the challenges of the future are identified. The project was brought in on schedule and within budget

Jan 1, 1991

By I. L. Bell

The ironmasters of America had asked the Iron and Steel Institute to visit the USA. The Council decided it was not possible to accept, but Mr. Bell visited; this is an account of his trip. Topics covered include transport, charcoal, coal measures, coal, anthracite, bituminous coal, flux, magnetic iron ore, specular iron ore, limonite, red hematite, clay ironstone, black band ironstone, smelting works, blast furnaces of Pennsylvania, Lake Champlain furnaces, Lake Superior furnaces, Cleveland furnaces, Pittsburg furnaces, Missouri furnaces, and those of the southern states. He goes on to describe Catalan hearths, malleable iron works, Bessemer works, the Blair steel process, and labour.

Jan 12, 1875

By J. D. Appleton, J. Ridgway, K. B. Greally

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The results suggest that meaningful geochemical maps can be produced from very low-density surveys, and that existing data sets could perhaps be incorporated into such a map series with the use of a system such as Uniras software. There are still many problems to be resolved, however, including the compatibility of data derived from different analytical methods, and the precise methods to be employed will necessarily require international agreement. Sampling densities should be chosen on the basis of the scale of the geochemical and geological features to be distinguished and will vary from region to region. Reanalysis of selected samples from archives to increase the range of elements determined or to unify analytical methods is only likely to be effective if the original survey was at quite a low density

Jul 1, 1991

By D. Bitzios, A. Gracia, V. Meggiolaro, J. D. Baker

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A large deposit in Spain and several smaller ones in Greece and Sweden were investigated. Beneficiation testwork, including the development of an innovative wet circuit, was undertaken in Italy. The Spanish Ilustracion deposit lies occurs in thin, white layers throughout a zone 35-40 m thick and 1.5 km long, in laminated calcsilicates. Total resources of more than 100 000 000 t include proven open-pittable reserves of 4 500 000 t averaging 35% wollastonite. The beneficiated product is suitable for various applications, including ceramics. The Swedish and Greek marble-hosted skarn deposits include Albatross, with 2 500 000 t of reserves at 30% wollastonite, and Panorama, with reserves estimated at more than 700 000 t

Jun 21, 1905

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991