Search Documents

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By A. Yörükoglu

In this study, thorium mineral that found in the complex ore deposit bearing bastnasite, fluorite, and barite from Eskisehir - Sivrihisar district has been tried to extract by using HCl and H2SO4 leaching. Ore sample of approximately 3 tons taken from the ore deposit has been homogenized in order to obtain composite samples by means of ore preparation techniques for experiments. Results of chemical analyses of composite samples are as given; 40.8% CaF2, 35.35% BaSO4, 2.01 Ce, 1.5% La, 0.39% and 0.1% Th. HCl and H2SO4 leaching processes have been performed to gain Th in the ore. For determining the optimum particle size, the samples have been ground under controlled conditions and brought to the sizes of 0.065, 0.2, 1 and 3 mm. Leaching experiments have been carried out in both HCl and H2SO4 acids without roasting and roasting at the temperature of 900°C for 1, 3 and 6 h retention times for all particle sizes determined before. In the experiments, the highest Th recoveries reached are as follows; 78.74% Th when H2SO4 and 1 mm particle sized sample used, and 1 h roasting applied and 73.38% Th when HCl and 1 mm particle sized sample used, and 3 h roasting applied. Keywords: thorium, leaching, concentration, sivrihisar, roasting

Sep 1, 2012

By J. K. Afidenyo

Microbial pretreatment of a double refractory gold ore was investigated using a white rot fungus, Coriolus versicolor (ATTC 20869) to improve gold extraction. A series of preliminary tests were conducted to determine the amenability of the ore to fungus degradation. Pulp density, temperature, pH and retention times were the process variables considered. Both a single. Stage and two-step processes were studied to establish process conditions. During the single stage process, the ore was contacted with the fungus culture (biotic) for 3weeks at 30°C and pH 10.0. For the two-step process, the first step involves ore contact with the culture medium (abiotic) at 45°C and pH 10.0 followed by fungal contact (biotic) at 30°C. Results indicated that carbonaceous matter is not degraded but passivated by the fungus; as preg-robbing activities dropped significantly from 18.1% to below 1.0%. The single stage process resulted in higher gold recovery than the two-step process Gold ex-traction by cyanidation of the pretreated ore was 78.9% for the single stage compared with 15.0% for the untreated ore. In the two-step process, only 73.3% gold extraction was achieved. Application of the two step process conditions to a high grade flotation concentrate, resulted in 93.3% gold ex-traction as against untreated concentrate of 30.5%. The results show that the microbial pretreatment process degraded sulfide sulfur, passivated carbonaceous matter and enhanced gold extraction from double refractory gold ore and concentrate.

Jan 1, 2014

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

By Priyanka Dhar, Kurt Aasly, Hanumantha Rao Kota, Hassan Bouzahzah, Maria Thornhill

The interest in investigating the processing characteristics of mineral deposits in Norway has seen an upsurge in the last decade. One of the major areas of interest is a huge copper deposit, operated by NUSSIR ASA located in the Repparfjord Tectonic Window in the caledonides of west Finnmark. This study reports analysis of ore from the deposit for development and modifications in the flotation flowsheet for the NUSSIR ASA copper ore. The mineralogical characterization for the ore sample was achived by optical microscopy and Zeiss automated mineralogy while grinding characteristics were tested using Bond Index tests. The results confirmed the presence of Cu minerals in the form of chalcocite, chalcopyrite and bornite in the samples, which are mainly liberated in the – 105 µm size range. The majority of non-liberated copper sulphides associated with silica and the carbonates varies from 3 to 28 percent in the –250 µm samples . It is also observed that the copper minerals are uniformly distributed in all size ranges. Selective flotation of NUSSIR copper ore was performed in different size fractions with a motive to identify the correct liberation size and thus to obtain a copper concentrate meeting the quality requirements. The flotation experiments are essentially performed in two stages: the rougher and the cleaner stage. Mass balance calculations were performed showing that approximately 88 percent of copper can be obtained at the end of the process. Ultimately, overall circuit copper recoveries ranged between 83.5 to 88.1 % with a concentrate grade of 35 to 48 % Cu.

Jan 1, 2018

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By S. Banisi

Thickening is the most widely applied dewatering technique in mineral processing. Thickeners are used to increase the concentration of suspension by sedimentation, accompanied by the formation of a clear liquid. As the particles get finer the thickening process encounters difficulty due to a significant change in the settling behaviour of particles. The batch settling tests of coal refuse of a coal washing plant which contained 91% particles smaller than 38µm and 0.6% coarser than 75 µm showed that the optimum feed percent solids that provided highest flux (solids handling capacity) was 4%. The flux of the pulp with the plant solids concentration (i.e., 10%) was 60% lower than that of the pulp with 4% solids. A thickener with a diameter of 22m based on the dilution of feed from solids concentration of 10% to 4% was designed. Monitoring of the thickener performance for a period of one month in the plant indicated that on average the feedrate of 25t/h (dry solids) with solids concentration of 10% could be thickened to the underflow concentration of 26.5% with a clear water overflow. It was found that the key component of the successful operation of the thickener is the dilution of the feed without which the overflow loses its clarity and the system ceases to operate under predetermined conditions. Specially designed feeding system which efficiently dissipated the energy of the incoming flow and staged flocculant addition regime are among the main contributing factors in making the design and operation of such thickener possible.

Jan 1, 2014

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012

By Kang N. Zhong, Hui H. Luo, Yi H. Wei, Yu L. Wang

"More than 85% of phosphorous reserves in China occur as middle-low grade phosphate of sedimentary origin. The main gangues are dolomite, quartz, silicates, and clays. The characteristics of minerals are finely disseminated. Flotation results have shown that the floatability of apatite of this kind of ore is much worse than that of igneous and metasedimentary origin because of its high specific surface area. Although some effective depressants, such as naphthalene sulfonate and phenanthrene sulfonate, are used to decrease the MgO content in the P2O5 concentrate, its presence is still high (about 2%) in the Chinese concentrates. Meanwhile, the wastewater may cause some environmental problems. Batch flotation results and measurements of specific surface area and CO3 2- have revealed that there is a relationship between the floatability of apatite and the surface area.A two-stage flotation flowsheet, which includes a combination of direct and reverse flotation, was developed for beneficiating sedimentary phosphate ores. The direct flotation was conducted in an alkaline medium and most of the apatite and carbonate minerals floated leaving quartz and siliceous gangue in the sink. In the reverse flotation circuit, the floated product was further beneficiated in an acidic medium to eliminate the carbonate as a float product. Apart from the high quality of concentrate, the two-stage flotation also facilitated the treatment and the recycling of wastewater. A wastewater recycling procedure was developed and tested in a continuous flotation process. The key factor was the careful selection of effective and non-toxic reagents."

Jan 1, 2003

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By Chen Zhiqiang, Luo Chuansheng, Chen Ziqiang, Liu Jianguo, Rao Jinshan

To comprehensively utilize the valuable resource in tailings, increase the economic benefit of mine, reduce the amount of tailings, prolong the service life of tailing dam, the comprehensive utilization of tailing resource is arousing the attention of more and more mines. Research of comprehensive recovery of feldspar and silica from Cu-Mo floatation tailings has been furthered. Technology of "De-sliming-Magnetic Separation-Reverse Flotation-Feldspar and Silica Separation" has been developed to utilize the resource. Slime is removed and reagents cost is reduced by de-sliming. The specific effective collector ZL is used in gangues reverse flotation, and GZ-818 is the collector in feldspar and silica separation. The grinding operation is vital to ensure the liberation degree of feldspar and to eliminate the reagents pollution on minerals surface. To a Cu-Mo flotation tailing assaying K2O 5.22%, Na2O 2.22%, Fe2O3 1.95%, Al2O3 12.05%, SiO270.66%, superfine K-feldspar and silica concentrates can be produced. The feldspar concentrate productivity is 29.67% assaying K2O 8.99%, Na2O 2.86%, Fe2O3 0.16%, Al2O3 16.99% and SiO2 68.92%. The silica concentrate productivity is 14.20% assaying 0.17% K2O, 0.04% Na2O, 0.01% Fe2O3, 0.55% Al2O3 and 98.17% SiO2. The technology provides technological reference model for the similar mines.

Jan 1, 2014

By A. Vidyadhar

Using pure quartz and hematite minerals, the adsorption mechanism of mixed cationic/anionic reagent schemes was investigated through Hallimond flotation studies. The flotation response of quartz and hematite independently with cationic and anionic collectors as well as with mixed cationic/anionic collector systems is assessed. The flotation response as a function of pH and collector concentration was investigated. The single mineral flotation tests in the presence of anionic collectors, quartz does not respond to flotation, but the C12 amine flotation of quartz was observed to be pH and concentration dependent. It was observed that hematite flotation recovery is maximum at acidic pH with sodium dodecyl sulphate (SDS), neutral pH with oleate, and at basic pH about 9.5 with C12 amine. Flotation results with both quartz and hematite indicate an increased adsorption of cationic collector in the presence of anionic collector apart from its own co-adsorption. The incorporation of oleate in between C12 amine molecules decreases the electrostatic head-head repulsion and thereby increasing the adsorption of C12 amine due to attractive tail-tail hydrophobic bonds, besides forming a closely packed adsorbed layer enhancing the hydrophobicity. The increase in oleate concentration beyond C12 amine concentration leads to the formation of soluble C12 amine-oleate complex / precipitate and the adsorption of these species decreased the flotation since the alkyl chains are in chaotical orientation with a conceivable number of head groups directing towards the solution phase. Keywords: quartz, hematite, adsorption, mixed collector system, flotation, zeta-potential

Sep 1, 2012

By Liu Chun-Bao Sun, Hong-Jun, Wei Zhang, Tao Xu

SABC circuits have gained widespread attention within China, and are being gradually applied to many mines. However, the domestic knowledge of comminution process is still relatively basic, and the design and production management of the application of SABC technology lack guidance of scientific theories. This research project focuses on the Phase I SABC milling circuits of Wu Shan Porphyry copper mine. Targeting the design and operation problems of existing process and circuit, and without increased investment and alterations in equipment, the new technologies will combine ordinary crushing and grinding theories as theoretical guidance, and borrow JK Simulation Software (JKSimMet) for analysis in order to optimize the comminution process, efficiently allocate production output and energy consumption, eventually resulting in increased production and energy efficiency. Using JKSimMet Simulation Software, and combining theoretical optimizing and practical production techniques, as well as the on-site situation, the eventual SABC comminution process and circuit optimization plan is: increasing the grinding Ball charge from 8% to 10% v/v in the SAG mill; Setting the Ball charge in the Ball mill to 27% v/v and the maximum operating power draw to 5 800kW; replacing the HP Series crusher with a TRIO TC84 crusher, which is without a power controller, and adding a pebble bin. The final optimization result is: Maximum system processing capacity increased between 20%-26.7%, specific energy consumption reduced by more 2.0 kWh/t, creating an economic benefit of over 300 million RMB, thus achieving the goal of increased production, reduced energy consumption, and improved profitability.

Jan 1, 2014

With shortage of sulfide nickel ores, laterite ore was paid more attention by scientists. Because its grade is commonly lower than sulfide nickel ores, laterite ore can not be utilized effectively be-coming the bottleneck of study. Leaching laterite ores from Yuanjing, Yunnan province, organic ac-ids show better selective than sulfide acid in nickel and cobalt recovery. Organic acid has low de-pendent on pH, keeping leaching capability even higher than 3. On the other side, when pH up to 2, sulfide acid can not leach laterite ores any more. After four kinds of organic acid leaching laterite ores, besides citrate, malate and succinate have good leaching and effectively selective capability. Especially, succinate has the best selective leaching capability of nickel and cobalt in four kinds of organic acids for latter anion purification and separation. Isolated from waste water with sugar, Aspergillus niger (zs1) has great capability to produce organic acids and vigorous growth. Laterite ores have been respectively processed by direct-leaching and indirect-leaching. Indirect-leaching gives a better result than direct-leaching. Extraction of nick-el by indirect-leaching reaches 44.3%, far more than that of direct-leaching. Moreover extraction of nickel at pulp density of 5% is higher than that at pulp density of 10%, reaching 63% in 11 days and extraction of cobalt also is 48.1% in the same period. Compared with nickel and cobalt, iron gives low extraction in solution, containing organic acids produced by Aspergillus niger .

Jan 1, 2014

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By Rasool Hejazi

The feed to Chadurmalu iron ore concentrator plant is a mixture of magnetite and haematite iron ore with a Fe/FeO ratio of about 8. The feed to plant, after grinding via wet SAG mill, is pre-separated by wet low intensity magnetic separator. Magnetic product is conducted to magnetite processing circuit for producing magnetite concentrate, and nonmagnetic product is directed to haematite processing circuit. Due to surface oxidization of magnetite particles and a decrease in magnetic attraction properties, significant amount of these particles are misled to tailing which results in decreasing the efficiency of haematite processing circuit. This problem can be remedied by using magnetic drum separator with more magnetic intensity and/or gradient. In this paper, the replacement of LIMS separators with wet medium intensity magnetic separators with a field intensity of 3800 gauss on drum surface (MIMS) have been suggested and considered as the most suitable solution to prevent the loss of magnetite particles. The results of carried out investigations with replacement of drum separators in industrial scale, showed that utilizing MIMS in magnetite processing circuit resulted in increasing final concentrate weight recovery on average by 2.59%, without any adverse effect on the concentrate quality; decreasing the magnetite content in the feed to high gradient magnetic separator (HGMS) by about 3.5%; decreasing the feed to floatation part by about 7% and consequently decreasing consumption of chemical reagents; increasing Fe/FeO ratio of the feed to plant. Keywords: iron ore, medium intensity magnetic separator, haematite, Chadurmalu

Sep 1, 2012

By N. I. Tyushkova

On the basis of detailed studying of mineral structure of ore and treatment products it is established that the given ore refers to oxidized Pb-Zn vein-disseminated ores. Technological special features of the basic ore minerals and the reasons causing their obstinateness that is defined by following features are revealed, presence at dominating quantity difficult to float lead minerals: mimetesite (9.67%), green lead ore(0.48%); non float: bindheimite (2.16%) and plumbojarosite (0.36%) and high assay of oxides and hydrous ferric oxides; also thin, emulsive and submicroscopic segregations of the defined minerals in swamp ore. As a result of researches the scheme of gravitational-flotation treatment was conducted in semi-industrial scale. It allows to receive two concentrates from ore: a lead gravitational concentrate of mark ??-4 with the assay of 55.5 % of Pb and 0.77 % of Zn; and a Pb concentrate of mark ??-7 with assay of Pb of 40.97 % and Zn of 1.39 %. The total assay of Pb in concentrates makes 81 %. The efficiency offered by gravitational-flotation schemes is defined by possibility for recovery of big impregnated lead minerals under gravitation. The use of this method of gravitation has allowed to recover such mineral as beudantide and to exclude irrevocable losses of lead in tails which are connected with this mineral. Scientific value of the presented researches is connected with the fact the problem of extraction of the oxidized minerals of Bb and Zn is rather difficult and insufficiently studied. Keywords: flotation, oxidized forms of Pb and Zn

Sep 1, 2012

By Takaaki Wajima

The slag was attempted to be converted into the adsorbent for phosphate removal from aqueous solution using the alkali fusion method. The slag was mixed with NaOH powder (NaOH / Slag = 1.6), and then the mixture was heated at 600 ? for 6 h to prepare the precursor. The precursor was stirred at room temperature in distilled water to synthesize the adsorbent, and the removal ability of the obtained adsorbent for phosphate from aqueous solution was investigated. The products, including hydrocalumite and calcite, were synthesized, and the removal efficiencies of the adsorbent for F- and PO43- showed higher than those of raw BF slag, especially removal of PO43- are excellent (99 %), while the removal of Cl- , SO42-, NO3- and Br- was minor. The adsorbent could remove PO43- selectively in the co-existing solution of Cl-, NO3-, F-, SO42- and Br-.The equilibrium adsorption capacity of the adsorbent for PO43- was extrapolated using Langmuir and Freundlich models, and experimental data are found to fit Langmuir than Freundlich. The calculated maximum adsorption capacity of the adsorbent for PO43- is higher than other adsorbent reported previously. The high affinity of the adsorbent for PO43- in aqueous solution was caused by the formation of hydroxyapatite [Ca5(PO4)3(OH)] and brushite [CaHPO4?2H2O]. The prepared adsorbent is expected to be anew inorganic adsorbent for the removal of phosphate ion from wastewater. Keywords: Blast furnace slag, Alkali fusion, Phosphate removal, High selectivity

Sep 1, 2012