Search Documents

By F. W. Guernsey

Of all the elements, sulphur occupies a place by itself. It is mined in situ, in such quantities and of such purity that, as regards the tonnage produced, it is the first of any element on the list. Iron and coal the great tonnage producers, are combinations of elements, while sulphur is mined and marketed almost chemically pure. It is sold, in large quantities, commercially, calling for a purity of 99.5 per cent while for medicinal purposes, the Pharmacopoeia requires only 99 per cent. purity. It is a very common commodity, and like many common things is of extreme importance, in the progress of our civilization. The substance has been known from the earliest times, the word sulphur being derived from the Sanskrit Culvari", hence the Latin Sulphur. Commercially it is also called brimstone, this word being a derivative of the Anglo-Saxon Bryne Stane or burning stone. From our younger days, we have been more or less familiar with the mineral. On the spiritual side being threatened, if we did not behave ourselves, with an ultimate consumption in a lake of fire and brimstone, (which in moments of reflexion was not pleasant to contemplate) while our bodily ills were taken care of by inward applications as a spring medicine. In both instances, the effect required, was generally attained. Sulphur occurs in nature, both free and in the combined state, it being estimated that it forms, over one tenth of one per cent of the first ten miles of the earths surface. (I do not know who did the estimating and it is not guaranteed).

Jan 1, 1923

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By Karl J. C. Harries

"5.1. INTRODUCTIONThis chapter is intended as a general overview of the subject of royalties between private parties – royalties extracted by governments are not dealt with. This same subject is covered in detail in Volume II, which critiques many sample provisions taken from agreements, giving both pros and cons. If you find something that interests you in this chapter, check Volume II for extra information. Detailed cross-referencing to Volume II has not been attempted, however, most subjects mentioned in this Chapter will also appear in Volume II, usually in greater detail. Reference should be made to the Index.A Brief History of Royalties1In the early days of mining in Canada, the tendency was to sell a claim for cash and to move on, using the stake to look for and stake more prospects. As prospectors became more sophisticated and Canada’s North opened up, the market for properties and the number of mining properties available increased dramatically. Speculation and the practice of consolidating several small properties into one large holding entity became common. In “hot” areas, the speculators2 could far outnumber the prospectors, many of the former having little or no prospecting expertise but lots of market and promotional savvy. However, to consolidate a number of small parcels into one large project can be expensive, and many of the parcel owners became interested in keeping a share in the project, rather than giving up everything. Speculators who were trying to consolidate small parcels wanted to minimize cash payments to parcel holders (usually they did not have much cash and preferred it flowing in their direction rather than away from them). Accordingly, non-cash transactions were developed to meet the aspirations of both owners and speculators."

Jan 1, 2003

By R. S. Douglas

Introduction During the past few years, a number of changes in the mine operations at Copper Mountain have taken place. The modernization and mechanization were necessitated and given impetus by wartime and other conditions, which were: (1) The urgent need for copper for wartime purposes. (2) The scarcity of skilled labour for underground work. (3) The increase in labour and supplies cost. (4) The necessity of finding ways and means of increasing the output per man-shift, because of the scarcity of skilled labour and the rising cost of labour. (5) The desire to increase safety measures, reduce the silicosis hazard, and aid mine ventilation. (6) The desire to improve the general working conditions in the mine for all workmen. (7) The desire to reduce the amount of dilution in the ore stream by a more selective yet highly productive method of mining. To this end, mining with diamond drills, and transferring broken ore with slusher hoists, appeared to be the answer to the problem. After considerable discussion and estimation of costs for comparison with those of the operation as carried on at that time, the proposed methods were tried out and, in practice, gave very gratifying results. Reference at this point is made to the paper written by C. H. Brehaut, W. N. Taylor, H. A. Shannon, and R. S. Douglas, which was published in the September, 1945, issue of Mining Technology, by the American Institute of Mining and Metallurgical Engineers, Inc., and subsequently in commercial mining journals. Since that time some improvements have been made in undercutting an orebody - the first through experiment and practice, the second through making use of the earth's barodynamic or gravitational forces. It is the purpose of this paper to describe and discuss these later developments.

Jan 1, 1947

By The Mill Staff

"IntroductionCOMMENCEMENT of operations at the new No. 7 shaft and 10,000-ton mill at Creighton mine was a major step in the programme of conversion to all-underground mining by the International Nickel Company of Canada, Limited. Planned ten years ago, the orderly transition has been greatly speeded-up to offset the heavy drain on production imposed by World War II and also to meet the increased demand for nickel caused by the current international situation. Development of new mining methods, and process changes in the reduction plants, have made possible the economic recovery and utilization of ore of lower grade than formerly used and of varying metallurgical characteristics. By 1953, when the Company's open-pit mining operations are scheduled for completion, the hoisting capacity of its five underground mines in the Sudbury district will have been increased to 13,000,000 tons per year, compared with 5,700,000 tons of underground ore hoisted in 1950.Two types of ore occur at Creighton. One is a breccia and stringer type that contains a high percent-age of massive sulphides and is located in sheets along shears and in large and small pockets on the underside of the main norite mass; the other type, forming the main part of the ore zone, is mineralized norite that occurs as a •sheet up to 400 feet thick overlying tl1e breccia ore. In both types of ore the minerals of economic interest are pentlandite, which is intimately associated with pyrrhotite, and chalcopyrite. Early mining was confined to the breccia ore; this ore was mined by open stoping methods. The hanging-wall was later allowed to cave, with the result that the old stopes are now filled with caved low-grade ore."

Jan 1, 1952

By A. G. Roach

Introduction This paper deals with the operations and plant of the Craigmont Corundum Project, formerly of Wartime Metals Corporation but now under the Mines Section of the Resources Development Branch of the Department of Reconstruction and Supply. Corundum is recovered by the re-treatment of an old tailing deposit at Craigmont, Ontario. Crude concentrates so produced are shipped to the plant of the American Abrasives Company, Inc., at Westfield, Mass., for final processing and distribution to the abrasive industry. The plant was recently described in a paper entitled Craigmont Corundum which was presented by the writer before the Chicago meeting of the A.I .M.E. in February, 1946. General The Project is located on? lots 4 and 5, concession XVIII, township of Raglan, Renfrew county, Ontario, near the village of Combermere, which is on Highway 62. The property is about 135 miles from Ottawa. The general area enjoys a pleasant climate with moderate summer temperatures, though the winters are rather severe, the mercury frequently falling to - 35 deg. F. The excellent boating, fishing, and hunting have made the district a favourite resort for tourists. Lumbering is the main industry. Some farming is carried on, but the soil is poor and much of the land is hilly and rocky. There are no other operating mines in the immediate vicinity, though several 'industrial minerals', including mica, feldspar, nepheline, beryl, socialite, and others have been produced in the area. The district is drained by the York and Madawaska rivers and is generously dotted with large and small lakes. The general elevation is about 1,000 feet above sea level, though numerous hills rising several hundred feet give a rolling appearance to the landscape.

Jan 1, 1946

By Stanley G. Butcher

"Introduction Many operators in western Canada, with a background in the minerals industry, talk of ""coal beneficiation"", whereas the coal industry generally uses the term ""coal preparation"" . The sophisticated cleaning circuits and thermal drying units found in western Canada makes the term beneficiation particularly appropriate. This chapter uses standard coal preparation terminology(l,2J and assumes general knowledge of coal preparation unit processes and equipment(3,4,5). The geologic setting and mining methods of western Canada, described elsewhere in this volume, present for preparation run-of-mine coals which have particular problems. As a result the cost of preparation is a higher proportion of the total minesite production costs than in other coal fields . Preparation requirements are determined by the types of coals being produced and the markets in which they are sold. Western Canadian coals have a low sulphur content and do not require cleaning on this account. Prepared coal from western Canada has to be shipped vast distances -to the Pacific Rim countries and Ontario in particular -and the savings in transport costs justify the high costs of preparation. Factors which dictate selection and operation of the preparation processes are: i) Market specifications and coal rank. ii) Size distribution of particles and particularly the liability of coal and refuse particles to degrade during handling and processing. iii) Quantity and characteristics of the associated refuse. iv) Washability characteristics (the distribution of particles by specific gravity within each size fraction). v) Surface characteristics of the fines. vi) Variability of the raw coal. Where the product (coal or discard) has a high fines content special consideration must be given to dewatering, the removal of surface moisture, to give acceptable handle ability characteristics. In the severe winter climate of the western foothills and mountains thermal drying is necessary to prevent freezing of washed coal in stockpiles and railcars."

Jan 1, 1985

By M. Desjardins

The Hoyle Pond underground mine, located in the Porcupine Gold Camp, east of the city of Timmins, Ontario, Canada, is the cornerstone of Goldcorp Canada Ltd?s Porcupine Gold Mines. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. In order to meet increased flow requirements of 256 m3/s at the mine, a new Fresh Air Raise (FAR) and new surface fans were commissioned in early 2005. The newly acquired fans were capable of supplying the desired volume of air within a range of 1.5 and 2.0 kPa. Upon commissioning of the surface fans the total pressure was found to be exceedingly high; far beyond the design capabilities of the new installation. Consequently only one surface fan could be operated at any given time providing about half the required volume of air. Extensive work was immediately started aimed at reducing the system resistance in order to permit operation of the two fans in parallel and achieve the required mine flows. Larger booster fans were installed in parallel at the 900 m level, a 3 m raise bore linking the 450 and 900 m levels was developed to twin the existing fresh air circuit, and the FAR from surface to the 450 m level was twinned with the original FAR. This strategy, completed in 2012, resulted in a drastic reduction in system resistance and pressures, allowing the two surface fresh air fans to be safely operated in parallel and meeting the flow requirements. This paper describes details of the engineering design work and commissioning of the modified ventilation system, successfully ensuring the long term viability of the project.

Aug 1, 2013

By C. Jay Hodgson, P. J. MacGeehan

"The gold ore zones of the Campbell and Dickenson mines occur within a km-wide, 2 km-long zone of highly altered and anomalously fissile and deformed volcanic and subvolcanic intrusive rocks, cut by a series of mainly post-deformation mafic and quartz-feldspar porphyry felsic dykes.Three main periods of gold ore-forming hydrothermal activity are recognized. In the first, the mine rocks were extensively altered and gold and arsenic enriched; syn-volcanic auriferous veinlet and low-grade chemical sedimentary ores were deposited in what was a major discharge zone of a submarine hydrothermal system. The chemical sedimentary ores are closely associated spatially and temporally with domal rhyolitic extrusions. Because of its mechanical and chemical properties, this synvolcanic alteration zone became the locus of later deformation, and the site of the generation of auriferous hydrothermal solutions, perhaps by pressure solution processes at depth. These solutions deposited, synchronously with deformation and metamorphism, the second and most economically important type of ore zones in the mine: large foliation-parallel and foliation-oblique banded carbonate- 'chert' Rssure-filling veins.In the third and final mineralizing event, high-grade, pipeshaped zones of siliceous replacement-type mineralization, and quartz-arsenopyrite-gold veins, were superimposed on the previous mineralization types after most of the deformation, but before the emplacement of the late dykes. The source of heat and also possibly the fluids for the third mineralizing period may have been the dyke-forming igneous activity. The textures and mineralogy of the banded carbonate- 'chert' veins suggest a near-surface (<3 km) environment of deposition, but their relationship to the fabric of their host rocks indicates they were emplaced in an environment, presumably at considerable depth (5-10 km?), in which the rocks were undergoing intense penetrative deformation. This anomaly is unresolved."

Jan 1, 1982

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By C. A. Jeffrey, K. Pearson

Abstract - The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the overlying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release of volatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of lowtemperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehnite and pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, during post-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystalline calcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from fluid inclusion work indicates that two fluids were involved in the deposition of the zeolite veins. One fluid was initially of relatively high temperature (~100°C to 320°C) and low salinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other was of relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.), and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat flow, initiating the circulation of hydrothermal fluids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Jurassic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By C. A. Jeffrey, K. Pearson

The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the over-lying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release ofvolatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of low-temperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehniteand pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, duringpost-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystallinecalcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from ?uid inclusion work indicates that two ?uids were involved in the deposition of the zeolite veins. One ?uid was initially of relatively high temperature (~100°C to 320°C) and lowsalinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other wasof relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.),and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat ?ow, initiating the circulation of hydrothermal ?uids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Juras-sic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By L. Rodd, C. Walker, T. Koehler

"The energy content of slag represents approximately 80% of the total energy inputs to a laterite nickel electric smelting furnace. Conventional slag handling methods produce only low grade heat and the entire thermal content of the slag is wasted. A heat recovery system proven on BOF slag in the mid 1980&apos;s can be adapted to a laterite nickel rotary kiln electric furnace (RKEF) plant. Slag is granulated using a high velocity air jet inside a waste heat boiler to produce slag granules. Granules are cooled during flight via radiation to water-cooled boiler walls and by convection to the granulation air. This system has the potential to recover 80% of the total slag energy in the form of hot air and steam.Integration of the recovered slag energy into the RKEF smelter can be achieved by a number of methods, including the use of preheated air at the ore dryers, kiln or existing power plant. Energy from the slag boiler may be used to reheat boiler feed water from the power plant or to produce superheated steam and generate electricity. The heat recovery system can provide up to 25 - 30% of the total electrical requirement of each RKEF line and a reduction in CO2 emissions of 234,000 tonnes per year.The total cost of slag heat recovery, including CAPEX and OPEX, is $2.5/GJ, which is competitive with using coal when CO2 credits are $18 per tonne. With Clean Development Mechanism (CDM) carbon credits currently selling at €13 ($20 USD) per tonne CO2, there is considerable opportunity for slag producers in regions including South America, Korea, Indonesia and Africa. Increasing fuel costs and more wide-spread legislation for GHG emissions will likely create conditions in which slag heat recovery could generate a favourable return on investment."

Jan 1, 2010

By P. R. A. Andrews, R. K. Collings

"In cooperation with le Ministère de l&apos;Énergie et des ressources, Québec, le Centre de Recherches minérales, Sainte-Foy, Québec, and various silica producers, selected deposits of Quebec silica were identified in the southern region of the province and sampled to provide material for evaluation as glass and foundry sand by CANMET. The samples included both sandstone and quartz/quartzite. Head sample analyses ranged from 94.66% to 99.54% SiO2, 0.038% to 0.230% Fe2O3, and 0.16% to 4.51% Al2O3.Impurities included pyrite, iron oxides, and iron staining on quartz grains; carbonates as calcite; and alumino-silicates as clay and/or feldspar. Processing included size reduction to grain size, about 600 µm, by jaw, roll and cone crushers, and grinding in a muller-mixer. Removal of fines was achieved by attrition scrubbing and washing. Further removal of impurities was achieved by reverse flotation of iron oxide and alumino-silicate minerals employing both anionic and cationic collectors. Flotation resulted in a substantial improvement in the quality of most sands, the quartz concentrates analyzing 99.08% to 99.80% SiO2, 0.014% to 0.048% Fe2O3, and 0.06% to 0.49% Al2O3. Removal of iron oxide minerals was also investigated using the Sala HGMS. Iron oxide analyses of the non-magnetic fractions were comparable to the iron oxide analyses of the quartz concentrates obtained by flotation, 0.013% to 0.054% Fe2O3. On the basis of the samples submitted, silica from 5 of the 6 deposits studied has potential as source material for glass sand. Foundry tests showed that 3 of the 4 samples submitted for evaluation have potential as foundry sand."

Jan 1, 1987

By Ian R. Morrison

"Abstract - The Izok Zn-Cu-Pb-Ag volcanogenic massive sulfide deposit is located 265 km south of Kugluktuk (Coppermine), Nunavut Territory, Canada, in the west-central Slave structural province. The Izok deposit is owned 100% by Inmet Mining Corporation and represents one of the largest undeveloped zinc-copper resources in North America. The Izok deposit is hosted within and near the top of a thick sequence of predominantly felsic pyroclastic rocks of late Archean age. The hanging-wall stratigraphy includes additional felsic volcaniclastic rocks, andesitic and basaltic flows, thin sulfide-rich iron formations, and turbiditic sedimentary rocks. The felsic volcanic rocks are intruded by intermediate dikes and sills, followed by gabbroic dikes and sills. Both intrusive suites are interpreted to be volcanic feeders to the overlying flows. All lithologies are subsequently cut by younger, irregular, granitic pegmatite and diabase dikes. The volcanic and sedimentary rocks are regionally metamorphosed to pyroxene hornfels grade. The massive sulfides occur within a large (kilometer-scale) Na-depleted sericitic alteration zone. The immediate footwall and hanging-wall rocks to the deposit are characterized by zones of muscovite- biotite-sillimanite, lesser chlorite-biotite-cordierite, and locally intense silicification and sodium metasomatism. All lithologies have been affected by younger Ca-metasomatism. As currently defined, the Izok deposit comprises a cluster of five complexly zoned composite lenses: the Northwest, North, Central West, Central East, and Inukshuk lenses. The first four lenses are amenable to open-pit mining, whereas the Inukshuk lens will require underground development. The total indicated mineral resource presently stands at 16.5 million tonnes with a grade of 2.2% Cu, 11.4% Zn, 1.1% Pb, and 60 g/t Ag. Inmet Mining Corporation is presently reviewing the economic feasibility of developing the property."

Jan 1, 2004

By L. Magne, A. Pinto, M. Maldonado, J. A. Finch

Estimation of gas holdup from electrical conductivity measurements has been used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the electrical conductivity of the dispersed phase, continuous medium and the resulting mixture (dispersion). When applied to inferring the collection zone gas holdup in a three phase system and to facilitate real-time on-line measurement, the slurry is assumed to behave as the continuous medium and gas bubbles as a nonconducting dispersed phase. This article derives an equation for estimating gas holdup in a three phase system, eliminating the assumption that the slurry behaves as a continuous medium but rather as a dispersion of non-conducting solid particles in water. In this formulation only water behaves as the continuous medium in the sense of Maxwell, and gas holdup in a three phase system is then calculated from the application of the Maxwell model twice: (1) to determine solid content in a two-phase system, and (2) to determine solid plus gas holdup in a three phase system. To validate the new equation and quantify the errors incurred by assuming slurry is the continuous phase a laboratory flotation cell was instrumented to continuously measure the conductivity of two and three phase dispersions with known solids contents. As the amount of gas in a lab flotation machine is difficult to measure directly or by another indirect technique such as using pressure signals, 2.5 mm dielectric plastic spheres having a density of ca. 1.3 g/cm3 were used instead of air bubbles for validation. Experimental results demonstrated that the continuous medium assumption underestimates gas holdup and that the resulting bias error increases linearly with the solid content and decreases with the magnitude of gas holdup.

Jan 1, 2016

By H. R. Stockford

"A pyroxenite-carbonatite complex containing extensive pyrochlore mineralization was discovered during January, 1966, within an exploratory license area held by Consolidated Morrison Explorations Limited. Located 32 miles south of Moosonee, Ontario, the deposit was found under 100 feet of glacial till and Paleozoic sedimentary cover using airborne and ground magnetometer surveys. Exploratory and detailed drilling, totalling 47,625 feet in 85 holes, was completed in outlining the deposit to a maximum depth of 900 feet. Pyrochlore reserves are estimated at 62,000,000 tons averaging 0.52 per cent Cb,05 to a depth of 825 feet. Included in this tonnage is a high-grade section containing 10,000 tons per vertical foot grading 0.82 per cent Cb20 5• The deposit is still open at depth and the intrusive complex has by no means been fully explored.The columbium (niobium) mineralization occurs in a lineated calcite-dolomite host rock which has been intruded along a fault zone within a northeast-trending granulite belt. Potassium-argon dating indicates an age of 1655 million years.Preliminary studies suggest that the complex was intruded in a series of pulses in the form of a partially crystallized mush. The James Bay intrusive is unusual in that it is linear in form and contains only two main rock types - p•yroxenite and carbonatite. Nepheline-bearing syenites and associated rocks are notably absent. Moreover, the pyrochlore is essentially non-radioactive and free from many of the impurities generally associated with other pyrochlores. A test shaft to investigate soil conditions and to provide a 250-ton bulk sample was completed during 1968. Subsequent pilot-plant operations indicate that good quality pyrochlore concelttrates can be produced from this deposit."

Jan 1, 1972