Search Documents

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By Abhinav Karanam, Lukas Bichler

Yttria Stabilized Zirconia (YSZ) is a promising thermal insulator for high temperature environments due to its thermal stability and chemical inertness. As was demonstrated with other technical ceramics (e.g., Alumina), addition of Single-Wall Carbon Nanotubes (CNTs) to a ceramic matrix may significantly enhance the mechanical properties of the composite ceramic. In this work, 8 mol% YSZ with 0.2, 0.5 and 1wt% CNTs composites were prepared via Spark Plasma Sintering process. The densification, Vicker’s microhardness, specific gravity and microstructure evolution of the composites were investigated. The results suggest that the addition of up to 1wt% CNTs to YSZ yielded optimal combination of the studied properties. At higher addition levels, the specific gravity decreased and clustering of CNTs occurred, leading to poor densification and a relative loss of performance.

Jan 1, 2014

By Paul B. Warrington

This paper presents a discussion of the factors affecting copper scrap markets, including such items as price levels, freight. grades of material, sources and packaging. Reference will also be made to the effective life and turn-around of the copper content of some products. Introduction IN TERMS OF SIZE, copper scrap is second only to ferrous scrap in tonnage recycled. However, in total value, it is second to none. For example, world scrap recovery during the preceding 4 years averaged just under 2,300,000 metric tons per annum, and at an average price of 70 ¢ a pound, this works out at a turnover of about $3.5 billion, which indicates that the copper scrap industry, or recycling as it is now becoming known , is a substantial one.

Jan 1, 1977

By M. L. Trépanier

"Engineering and technical services are supplied by the Engineering Department, located at Thetford Mines, Quebec, approximately 60 miles southwest of Quebec City. The department serves the three operating mines in the Thetford area, the Asbestos Hill mine at Putuniq, Nouveau Quebec, and the Nordenham plant at Nordenham, West Germany. The Engineering Department is responsible for supplying the following services. 1. Administration and coordination of capital projects. 2. Engineering, design and drafting services for in-plant changes or improvements. 3. Preparation of geological plans for mine planning and ore reserves determinations. 4. Short-, medium- and long-term mining plans. 5. Rock mechanics studies and monitoring. 6. Grade control monitoring. 7. Environmental control engineering and construction. Details of the organization and services rendered will be the basis of the paper."

Jan 1, 1976

By Brian C. Asbury

Gold-bearing quartz veins with auriferou pyritic wall rock alteration haloes at the Komis deposit near Waddy Lake in northern Saskatchewan occur in fractured Archean intermediate volcanic rock flanking a plutonic felsic intrusion. Three ore zones totalling 1.5 million tonnes grading five g/t gold have resulted from a combination of patterns of high density of fracture-filling quartz veins created by contrasting competencies of four predominant rock types and preferential gold deposition in magnetitebearing andesite host rock. Pre-glacial surface weathering remobilized gold from a nearby pyritized intermediateto- felsic dyke to form the EP Zone with a wide variety of supergene accessory minerals. Much of the EP Zone wa eroded by glacial action to forn1 a highly anomalous gold-bearing till dispersion train which facilitated its di covery.

Jan 1, 1986

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962

By L. Sun

Recently, micro-tubular solid oxide fuel cells (SOFCs) have attracted the attention of many researchers because of their numerous advantages over larger tubular and planar SOFCs. These include excellent thermal shock properties giving rapid startup/shutdown capability, a high volumetric power density compared to larger tubular SOFCs, and reduced sealing problem compared to planar SOFCs. In order to screen cathode materials for micro-tubular SOFCs, the perovskite cathodes were deposited, using a variety of methods, on 10.5 mol % yttria-stabilized zirconia (YSZ) tubes. Their electrochemical properties were then evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods, based on a three electrode configuration, and with the reference electrode position carefully optimized. The oxygen reduction reaction kinetics at the cathode/electrolyte half cell were then investigated in detail.

Jan 1, 2005

By D. A. Rhys, M. Sieb, M. A. Prefontaine, C. L. Swanson, S. R. Frostad, H. Q. Smit

"Gold-silver mineralization at Red Mountain (1992 resource of 2.5 million tonnes grading 12.8 g/t Au and 38.1 g/t Ag) occurs within several discrete zones within a folded sequence of Middle to Late Triassic Triassic sedimentary rocks, Early Jurassic volcaniclastic and pyroclastic rocks, and Early Jurassic intrusions. Three phases of Early Jurassic sills and stocks collectively comprise the Golds/ide intrusions: (1) irregular bodies of medium-grained hornblende monzodiorite (Hillside porphyry); (2) hornblende-biotite + quartz porphyritic monzodiorite to quartz monzodiorite (Golds/ide porphyry; U-Pb zircon ages of 197.1 + 1.9 Ma); and (3) biotite porphyritic hornblende monzodiorite sills (Biotite porphyry). Contact breccias and igneous breccia dikes are common features of the Golds/ide intrusions. Chemical similarities and equivalent ages of volcanic rocks and intrusions, and the presence of intrusive clasts in volcanic rocks suggest that the intrusions are feeders to overlying volcanic units.Hydrothermal alteration affects all pre-Tertiary rocks on Red Mountain, including all phases of the Golds/ide intrusions. Several shallow-dipping alteration zones are developed sequentially above a propylitic quartz stockwork/molybdenum zone. These include: (1) sericite-quartz-pyrite alteration (pyrite-dominant alteration); (2) chlorite-K-feldspar-sericite-titanite alteration with disseminated and vein pyrrhotite (pyrrhotite-dominant alteration); and (3) brown to black tourmaline veins and K-feldspar-pyrite-titanite-actinolite alteration. Anomalous gold(> 0.3 g/t) mineralization is developed at the transition from the pyrite to the pyrrhotite dominant alteration over a > 1 km2 area. Within this anomalous zone, high-grade (3 g/t to 20 g/t Au) gold-silver mineralization occurs in 5 m to 29 m thick, semi-tabular pyrite + pyrrhotite stockworks with intense sericitic alteration and surrounding disseminated sphalerite + pyrrhotite.Stratigraphic, spatial and geochronologic relations and alteration zoning indicate that mineralization formed in a subvolcanic environment at the top of the Golds/ide intrusions and at the base of the Early Jurassic volcanic pile. The Golds/ide porphyry is interpreted to be the mineralizing intrusion. The alteration zoning, molybdenum-copper mineralized quartz stockworks, extensive Ksilicate and tourmaline alteration, and the relationship with a hypabyssal porphyritic intrusion show similarities to many porphyry systems."

Jan 1, 1995

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Testwork was conducted in order to compare the effectiveness of carbon based catalysts while oxidizing a gold-bearing pyrite concentrate under atmospheric conditions. Without the use of a catalyst the oxidation of pyrite was incomplete after 96 hours, resulting in roughly 60% pyrite oxidation. Furthermore the resulting sulphate yield from unassisted pyrite oxidation ranged between 72 and 84%. It is evident that atmospheric oxidation of pyrite is not viable due to slow oxidation kinetics and high sulphuric acid production when using a ferric sulphate media without a catalyst. The effect of two different carbon based catalysts, one Lewatit® AF 5 a new microporous carbonaceous bead, and the second a granular coconut shell based activated carbon, were tested under the same oxidation conditions as the unassisted pyrite tests. After 96 hours, Lewatit® AF 5 assisted oxidation showed approximately 96% pyrite oxidation with a sulphate yield ranging between 26 and 35%, while the activated carbon assisted oxidation reached approximately 100% pyrite oxidation with a sulphate yield between 36 and 37%. Testwork indicated that not only does the addition of a carbon based catalyst greatly improve the oxidation kinetics and lead to almost complete oxidation, the sulphate yield is also drastically reduced, resulting in very high elemental sulphur yields.INTRODUCTION Pyrite is an important sulphide mineral due to its ability to contain invisible gold concentrations up to 132 g/t (Chryssoulis & Cabri, 1990). As a result, ores composed of only a small amount of pyrite still have the ability to contain high gold grades. This refractory gold cannot be accessed via conventional gold leaching processes, such as cyanidation, and additional oxidative pre-treatment is required to liberate the gold, making it more amenable to extraction (Marsden & House, 2006). Current oxidative pre-treatments do exist consisting of both pyrometallurgical and hydrometallurgical processes including high temperature and high pressure leaching within autoclaves, biological atmospheric leaching and roasting. Autoclaves are a proven process reaching desirable recoveries within approximately a 1–2 hour retention time, due to the increased temperatures and pressures, allowing for an increase in dissolved oxygen (Marsden & House, 2006). The typical reaction for pyrite oxidation within autoclaves is presented in Equations 1, 2 and 3."

Jan 1, 2017

By Lin Li, Ahmad Ghahremaninezhad

"In this paper, the electrochemical behavior of ferric and ferrous couple on the pyrite surface was studied by application of the chronoamperometry technique in an acidic solution at room temperatures and atmospheric pressure. The effects of the pyrite origin, ferric and ferrous ions concentration on the electron transfer kinetics of Fe3+/Fe2+ reaction were probed. Tafel behavior of all the test conditions were developed. The results showed that the ferric-ferrous reaction on pyrite electrodes with different origins have a common mechanism, despite different reaction kinetics. The exchange current densities of the redox reaction have the same magnitude of about 10-5 A·cm-2, which is far lower than the value reported for the gold and platinum electrodes, but larger than that of the chalcopyrite electrode. The cathodic transfer coefficients are between 0.4 and 0.5, while the anodic transfer coefficients appear unusual with the lowest value being 0.23. It was also demonstrated that an increase of one order of magnitude of iron concentration has no clear effect on the exchange current density and cathodic transfer coefficients of Fe3+/Fe2+ redox reaction.INTRODUCTIONPyrite, FeS2, is mostly considered as a gangue mineral which frequently coexists with valuable minerals and metals, such as gold, copper and nickel. Its separation from valuable minerals can be a costly process (Chandra & Gerson, 2010). In refractory gold ores, the fine gold particles are locked inside the pyrite structure. Oxidative leaching of pyrite is a hydrometallurgical method to destroy the structure of pyrite and expose the fine gold particles to the cyanide solution in the downstream cyanidation circuit. Pyrite oxidative leaching can be achieved by oxidation of pyrite via oxygen and ferric ion(McKibben & Barnes, 1986). In fact, pyrite oxidation by oxygen and ferric is a significant source of acid mine drainage(AMD), which adversely causes serious environmental problems(V. P. Evangelou, 1995).The pyrite oxidation mechanism is accomplished in three consecutive steps: (i) pyrite is oxidized by oxygen and ferrous ion formation (Eq. 1); (ii) ferrous oxidation by oxygen and ferric ion formation (Eq. 2); (iii) pyrite oxidation by means of ferric ions (Eq. 3). Hence, both oxygen and ferric participate in the pyrite oxidation process (Moses & Herman, 1991):"

Jan 1, 2016

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By G. M. Ritcey, S. H. Lucas

"On the north shore of the St. Lawrence River, in Quebec, are located orebodies of low-grade titaniferous magnetite. The Quebec Mining Exploration Company (SOQUEM), who have an interest in the deposits, believed that beneficiation of the could generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility. A joint research project of SOQUEM and CANMET investigated alkaline roasting of a magnetic concentrate, followed by leaching of the calcine and separation and recovery of Cr and V by solvent extraction. Aluminum was recovered by precipitation.The present paper describes the roast-leach bench-scale and pilot-plant work leading to the development of the optimum conditions f or the integrated process.A plant flowsheet was developed for the treatment of 5 x 106 tons of magnetic concentrate per annum. Estimates of capital and operating costs were made.Based on a recovery of approximately 90% V, 85% Cr and 75% AI, the total hydrometallurgical plant fixed capital costs, including mining, concentration and shipping, are estimated at $1.021 x 109; the operating costs are estimated at $131.92/ton concentrate. Annual revenue from the Na2CrO4.H2O, V2O5 and A12O3 produced is calculated to be $421 x 106.IntroductionThe Quebec Mining Exploration Company (SOQUEM) acquired in 1968 an interest in four titaniferous magnetite orebodies located in Eastern Quebec. 85 miles north of Mingan on the north shore of the St. Lawrence River. The Mingan deposit, with an estimated tonnage of one billion tons, has a reported average grade of 43% Fe, 6.3% Ti , 1.60% Cr, 0.19% V and 6.1% Al with minor amounts of nickel. SOQUEM, on the basis of previous bench-scale data, believed that the recovery of chromium, vanadium and alumina by alkaline roasting would generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility on the coast. One of the approaches selected by SOQUEM for beneficiation of the ore consisted of a combination of magnetic concentration followed by alkaline roasting of the calcine."

Jan 1, 1980

By G. M. Ritcey, K. E. Haque

"Laboratory-scale sulphuric acid leach tests were conducted on Elliot Lake and Rabbit Lake ores in the presence of various oxidants, namely: Fe2(SO4)3, CI2, H2O2, NaClO3, MnO2, H2SO5, HNO3, Oxon e, K2Cr2O7, KMnO4, O3 and O2. Uranium extraction is significantly accelerated when an oxidant is present in the leach slurry. Uranium extraction of 96-99% can be achieved by maintaining the oxidation potential of the leach slurry in the range of400 to 500 m V (S.H.E.). A rough cost comparison of all the oxidant s indicates that the use of Fe2(SO4)3, 02, O3, C12, HNO3 or MnO2 is far less expensive than NaClO3 and the uranium extraction rates are similar to or better than with NaCIO3. For uranium extraction, it is concluded that gaseous oxygen (i.e., air or oxygen) would be the most effective and economical oxidant for the 24- to 36-hour leach of Elliot Lake ore; whereas for the 8- to I2-hour leach of Rabbit Lake ore, a strong chemical oxidant (e.g. NaCIO3, H202, 03, K2Cr2O7, H2SO5 or HNO3) would be a logical choice.IntroductionThe common practice for the treatment of uranium o res is leaching with sulphuric acid or with a carbonate-bicarbonate mixture. Generally, the latter process is ad opted when an excess (> 18%) of acid-consuming components (e.g., carbonate) is present in the ore. Irrespective of the nature of the leachant, the addition of an oxidant to the leach mixture is necessary to obtain a high uranium extraction.The maximum extraction of uranium can only take place when all the uranium is in the highest oxidation state (i.e.,U +6-uranic ion) . Because a certain percentage of uranium present in the ore is invariably in the lower oxidation state (i.e.,U+4-uranous ion) , the addition of an oxidant to the leach slurry is necessary to oxidize uranous ion to the uranic state."

Jan 1, 1982

By J. Keith Haddock

"The Luscar Mine is a metallurgical coal mine located in the foothills of the Canadian Rockies, 41 km southeast of Hinton, Alberta. The mine is operated by Cardinal River Coals Ltd., a 50/50 joint venture between Luscar Ltd. and Consolidation Coal Company of Canada. The mine produces a high quality medium volatile metallurgical coal which is sold on the export market principally to Japan and South Korea. Operations consist of a surface mine with capacity to produce 3.0 million tonnes per year and an underground mine which is currently mothballed due to market conditions.GeologyBedrock units within the Luscar minesite are of Devonian to Upper Cretaceous age. The commercial coal measures in the area are, however, confined within the Lower Luscar Formation. The Luscar Formation consists of a 460-metre thick sequence of interbedded sandstones, shales and coal seams. The sequence is primarily deltaic in origin, and is bounded to the north and south at the Luscar mine by tectonically induced thrust faulting.The only mineable coal seam at Luscar is referred to locally as the Jewel seam. Average thickness of this coal measure is usually 10.5 m to 14 m, although in some areas folding and faulting has produced ""pods"" of coal from 15 m to over 40 m thick while in others the structural deformation has thinned the coal to 3.0 m to 4.6 m. Waste within the Jewel seam seldom exceeds a metre of shale, carbonaceous shale or infrequent sandstone stringers.Reserves and Coal QualityProven surface mineable reserves, based on pit scheduling through 1996, are 50.8 million raw tonnes. An additional 19.2 million raw tonnes are contained in possible extensions to the present planned operations. These surface mineable reserves are considered to be those reserves within 155 m of the surface. Underground reserves, located within 770 m of the surface show that 25.7 million raw tonnes have been proven to date in additon to 27 .5 million indicated and 260 miIJion inferred.Coal specification at Luscar Mine is as follows:"

Jan 1, 1985

By V. Aprahamian, G. B. Harris, C. W. White, M. Tangen

"In 2005, the Royal Canadian Mint (RCM) commissioned a new silver electrorefining circuit. This circuit was intended to operate with a minimal electrolyte bleed for the control of copper. However, by the time of start-up, the levels of copper-rich silver doré to electrorefining had increased, and despite partial pyro-conversion in a small Top Blown Rotary Converter (TBRC), copper concentration in the silver anode still averaged 7.5%. This necessitated frequent replenishment of the electrolyte with fresh silver nitrate since copper displaced dissolved silver during electrolysis, and therefore requiring a robust copper bleed treatment step in order to maintain cathode silver flake purity at 99.99%. The originally-installed bleed treatment system could not meet the RCM’s needs. A thorough review of known technologies, however, did not indicate one capable of handling the copper load, and resulted, therefore, in the development of a novel copper hydrolysis approach for removal of copper as an insoluble basic nitrate salt, and recovery of the associated nitric acid for re-use in the circuit. Laboratory-scale trials showed reproducible results, and existing equipment was subsequently modified.INTRODUCTIONIn 2005, the introduction of a new silver electrorefining circuit at the Royal Canadian Mint (RCM) initiated changes in the way customer silver, collected from the gold doré circuit, was processed. These circuit changes were discussed in a recent paper (Aprahamian, 2015). A wastewater treatment plant had not been budgeted at the time, and this represented a significant constraint when considering the introduction of a wet processing circuit. After a review of various options, a turnkey silver electrorefining circuit was purchased from a European firm. Initially, enough cells were ordered to produce 2 million oz of fine silver (999), with the option to increase to 5 million oz. The selected equipment was based on a Moebius cell design combined with a silver grain pressure dissolver to produce make-up silver nitrate solution. Additionally, an evaporator/hydrolysis unit included in the package appealed to the Mint Refinery, on the basis that it offered a simple way to bleed dissolved copper in electrolyte without generating effluent."

Jan 1, 2016

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the 'Sudbury Basin'. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938